I have been using Ubuntu for a couple of years and always at the 1024 768 screen resolution.
I just finished installing version 10.04. It defaulted to 1280 1024.
I much prefer the 1024 768 because it is better for my older eyes, but when I attempt to change, the screen goes black for a minute and then stays at 1280 1024.
Since earlier versions of Ubuntu did it, this should also, but..
Need a driver for a Compaq P900 Trinitron monitor, Model PE1030 using Linux Mint 8 Helena. Unable to change resolution. Max is 600 x 400.
View 6 Replies View RelatedI have an asus eee pc with a 7 inch screen. the screen is small and today I attached a 15 inch dell monitor to increase the screen size. the dell monitor is displaying a 720x 400 resolution which results in a very large screen but no more space on the screen. I can select 1024x768 resolution in system,preferences, display. HOWEVER I cannot select APPLY to this resolution because the apply button is not visable on the bottom of the screen because the display is SOOOO big.
View 4 Replies View RelatedInstalled server 10.04 using an old Sony 19" multi scan 400ps CRT monitor. The command line font is less than 1/8" high: something on the order of a large 4pt or small 5pt font. Made several attempts to locate the correct info using the man functions and searching the archives, but so far have not been unable to find the needed information. The eye strain is about to make me eligible for a white cane with a red tip.
View 4 Replies View RelatedI use a laptop and Ubuntu 10.10 x86. Problem is I have a second monitor with 1280x1024 native resolution, and that resolution is not displayed in modes.So I solved my problem temporarily using this: Code:xrandr --newmode 1280x1024_60.00 109.00 1280 1368 1496 1712 1024 1027 1034 1063 -hsync +vsync
xrandr --addmode VGA1 1280x1024_60.00 The 1280x1024 mode appears and I do "apply" -> all OK. And then I press "make default" (where I get a pop screen confirmation warning me that will be the default config after reboot) - nice! Problem is: "make default" don't work! And I have to add a new mode after each login.
I have an acer aspire one netbook and in display properties it says the monitor is unknown. The trouble is that the screen is widescreen (16:9) but it has it as (4:3)so the screen is sort of stretched. Is the a terminal command as another way round this or how can i get the screen recognised?
View 4 Replies View RelatedI have a fresh installation of Debian 7.8 on my Dell Precision notebook. Somehow I failed to configure Xorg in a proper way. I do have X up and running, but I can not change my monitor resolution. Here is my graphics card.
Code: Select all$ lspci | grep VGA
00:02.0 VGA compatible controller: Intel Corporation Haswell Integrated Graphics Controller (rev 06)
01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Radeon HD 8800M Series
I tried to follow suggestions from Debian Wiki, somehow nothing really worked (https://wiki.debian.org/AtiHowTo)
Code: Select all# aticonfig
aticonfig: No supported adapters detected
Code: Select all# X -configure
Terminated with an error, below is the Xorg.0.log file
Code: Select all[ 227.953]
X.Org X Server 1.12.4
[code]....
I need to know how to change resolution on the screen and monitor
View 5 Replies View RelatedI mis-clicked and now my monitor resolution is WAY too high. I could fix that by re-clicking, but the menu to bring up the screen I need to click is off-screen.By blind clicking I got a command line window. Can anybody tell me the command line to bring up the system preference for monitor resolution?
View 2 Replies View RelatedJust installed Ubuntu 10.10 "Maverick Meerkat".
Install went through smoothly in both my laptop and an old Dell Optiplex GX 270.
Screen looks fine on laptop but terrible on the Dell. It's stuck on Refresh rate of 60Hz and flickers pretty bad. 60Hz is the only rate offered! How can I change the refresh rate to ~65-72Hz like is possible on earlier Ubuntu versions to ease eye strain?
I'm newbie linux user and I want to ask a question about my laptop display is too big i think its because of my screen resolution, how can I change my monitor resolution?
View 1 Replies View RelatedI just switched monitors to a Viewsonic VX2025 and I am unable to get beyond 1280 x 1024 using the nvidia x server settings. My graphics card is a GeForce 5200. These are connected with a DVI plug. I would like to be able to set my resolution to 1920 x 1080. (Also, the card and monitor worked at 1920 x 1080 in a previous windows machine.)
I have done a fair bit of searching and it appears that my issue is either the x configuration file or EDID. After 2 days of working with this it's gotten confusing to say the least. So, I'm looking to see if others have had a similar problem and how to solve it. I have not altered an x config file before, so not exactly sure of where to begin.
I have a fujitsu siemens monitor C776 (built by Hansol E17CL)
FC12 can't autodetect it
If I go system -> preferences -> display the button: detect monitor does not work
I can't change resolution which is stopped at 640x480:
I'm currently using ubuntu 10.04 version. I've recently purchased a BenQ E2200HD monitor. However, the monitor is unable to configure a resolution higher than 800x600. I've tried changing it via 'preferences' - 'monitor' etc. The monitor model is 'unknown'. and the highest resolution available is the 800x600.
I've tried changing it manually, but it says x.cong file does not exist. Xrandr doesnt seem to work either. Or i would get CTRC 262. My current set up is, intel i5 2600, 4GB Ram, Nvidia GTS 240. I'm pretty certain, my graphics card (despite being in the low end) can support HD resolution. Even if it can't, it surely can support a resolution higher than 800x600.
Just Installed the latest version of Ubuntu Netbook on my Toshiba Portege 7200 and the screen resolution is set to 800x600. The OS is not recognizing the fact the laptop can do 1024x768. I've been searching the net for a few hours to fix the problem and I'm not getting anywhere. The fix to the problem is to add the info below to the Xorg.conf file. This file does not seem to exsist on the latest version and if I create it manually it does not work.
# xorg.conf (X.Org X Window System server configuration file)
# This file was generated by dexconf, the Debian X Configuration tool, using values from the debconf database.
# Edit this file with caution, and see the xorg.conf manual page.
# (Type "man xorg.conf" at the shell prompt.)
# This file is automatically updated on xserver-xorg package upgrades *only* if it has not been modified since the last upgrade of the xserver-xorg package.
# Note that some configuration settings that could be done previously in this file, now are automatically configured by the server and settings. Here are ignored. If you have edited this file but would like it to be automatically updated again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
Section "Device"
Identifier "Trident Microsystems Cyber 9540 (rev 52)"
Driver "trident"
BusID "PCI:1:0:0"
EndSection
Section "Monitor"
Identifier "Integtrated LCD"
HorizSync 28-90
VertRefresh 43-85
#Modeline "1024x768_60.00" 63.50 1024 1072 1176 1328 768 771 775 798 -hsync +vsync
#Option "PreferredMode" "1024x768_60.00"
EndSection
Section "Monitor"
Identifier "VGA-0"
Option "Ignore" "true"
EndSection
Section "Screen"
Identifier "Screen 1"
Monitor "Integtrated LCD"
Device "Trident Microsystems Cyber 9540 (rev 52)"
EndSection
I was running my Acer V193 monitor at 1280x1024 resolution on KDE 4.3.1. Then after someone else used the computer the resolution changed to 1024x768 and I am unable to change it. Yast recognizes the monitor correctly, but when I run Sax2 it will not change it back to 1280x1024. It accepts that setting but when I start it again it is set at 1024x768. My xorg.conf indicates...
Section "Monitor"
Option "CalcAlgorithm" "XServerPool"
DisplaySize 376 301
[code].....
I just upgraded to 11.4 and after finding the right nvidia driver it finally works.But i can`t change my screen resolution to 1280x1040, right now it`s on 1024x786Software management says sax2 is installed but when i type it in a console i get the message"If 'sax2' is not a typo you can use command-not-found to lookup the package that contains it, like this:cnf sax2" Also in yast i can`t find a option to change the resolution of my monitor.
View 9 Replies View RelatedI am unable to change mu screen resolution in slackware 12.2. I am editing the xorg.conf in "etc/X11/" with nano. My graphics card is a ATI with 64MB RAM. My monitor is capable of 1280x1024 @ 60Hz. Heres the xorg.conf:
Code:
# File generated by xf86config.
# Copyright (c) 1999 by The XFree86 Project, Inc.
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions: .....
I installed fedora 14 on Dell laptop but I am unable to change resolution on my laptop also video quality is poor , I think proper drivers are not installed. I am new to Fedora, so probably missing something.
[root@localhost qalandar]# lspci -nnk | grep VGA
00:02.0 VGA compatible controller [0300]: Intel Corporation Core Processor Integrated Graphics Controller [8086:0046] (rev 02)
When I boot my computer I get this message: Warning Pc video resolution is out of range Change setting to recommended resolution 1280x1024 @60mh So I hit ctrl alt f1 I typed in Sudo dpkg-reconfigure xserver-xorg Nothing happens. It's been very frustrating because with everything that I've looked up it says that it's suppose to guide me through something. I desperately need my computer for school.
View 8 Replies View RelatedI have a dual monitor setup in Ubuntu, with my main monitor on the right and the monitor I want to extend to on the left monitor, but I can't seem to get it to do this, it always has the 'desktop' on the left monitor and then extends onto what I want to be my main monitor. I have an ATI Radeon 4350 Graphics card.
View 1 Replies View RelatedHow to change the resolution of my tv to be the same as the monitors. I mean cloning ..
View 9 Replies View Relatedjust installed ubuntu10.04 has set monitor resolution to 800x600 i need 1920x1080 i have been at this for two days now and getting absolutely no where , i could set this on windows in 5 minutes , why does it need to be so hard on ubuntu, i really prefer ubuntu to windows but problems like this really can drive one to despair. i have tried so many different web sites and follow instructions but keep getting command not found which i dont understand why. here is an example of something i tried in terminal xrandr --output VGA --mode 1920�1080 --rate 50 i get warning: output VGA not found; ignoring.many other things i have tried come up with command not found .
View 4 Replies View RelatedI have a laptop with an "ATI Technologies Inc Mobility Radeon HD 3400 Series" video device. I have trouble configuring the second VGA monitor attached to the laptop to 1024x768 resolution. It is always stuck on 2560x800. My xorg.conf file is as follows:
Code:
Section "ServerLayout"
Identifier "amdcccle Layout"
Screen 0 "amdcccle-Screen[1]-0" 0 0
Option "DefaultServerLayout" "dualscreen"
EndSection
[Code]...
Just installed 11.04 on a box that it is on a kvm switch. As long as the switch is connecting the monitor to the booting Ubuntu box, the resolution of the monitor is detected OK. However, if for some reason I am working on a different box and the KVM switch is routing K V and M inputs to the other box, then Ubuntu defaults to what seems a botched VGA setting (i.e. it chops off top and left sections of the display).While in this "VGA" mode if I log out and log in, it re-detects the resolution ok.Is there any way to force Ubuntu to use a specific resolution no matter what? In this way, if I am working on a different box while waiting for Ubuntu to load, when I switch the resolution will be OK.I tried the only thing I can think of and this is to set the "good" resolution as "default" for "all" monitors, but it has no effect.
View 2 Replies View RelatedI was playing around with the NVidia settings control panel today and I saw that its Resolution dropdown was giving me options for
1680*1050
1920*1080
My monitor supports up to 1440*900. When I selected one of the higher resolutions, it didn't look very sharp, and the text was somewhat fuzzy and lacked clarity. Was this rendering being done by the graphics card but 'compressed' by the monitor?
The status said 'switched to metamode'. I tried searching but found nothing - what exactly does MetaMode mean? I'm more interested in understanding what was happening, only experimenting with the higher resolutions. What monitor and resolution do you have?
why both ubuntu and centos 5.4 will only give me 800x600 resolution on my monitor when opensolaris immediately gives me 1280x1024?The first time I tried ubuntu it gave me 1280x1024 and now will only make 800x600...This is a viewsonic VG930M Monitor..
View 4 Replies View RelatedI simply ran the Guest Additions CD (on VirtualBox), double clicked the x86 (I'm running 32-bit) executable, and got that error.
View 6 Replies View Relatedso when ppl bring me their computer and i install them ubuntu in my monitor when they take their computer to their home ubuntu does not keep the screen resolution i set for them.
View 4 Replies View RelatedI have a 30" apple cinema display. The monitor handles up to 2560 x 1600 pixels which is the optimum resolution for this monitor. I found out that most apple monitors have nvidia graphic card.The monitor is hooked up to a motherboard Intel BOXDG45FC. This motherboard has Onboard Video Chipset Intel GMA 4500. However, using KDE interface I dont get beyond 1280x800 resolution for the monitor.How can I get the maximum resolution for the monitor?
View 9 Replies View Related