Linux box could act as a router? I have one machine running ubuntu, another running windows 7, a cable modem and a switch. Is it posible to share the connection between both computers by making the linux box a "router"?
View 7 Replieshow I could file share, or make the whole Hard Drive (HDD) accessible to another computer. The two other computers I have are a Toshiba Laptop with Ethernet and USB, and a iMac Intel with Firewire, USB, and Ethernet. Putting these to use along with:
Three Ethernet Cables
Two Printer Peripheral USB Cables
The Two Computers
A 2GB Flash Drive
That is all I can think of right now. I do not want to use CDs. In a way, I would like to do a network boot. So, how do I get the whole HDD visible to the others computers (either/both) and be able to write to it? I want to put Xubuntu on it, and earse the rest of the Hard Drive. The computers getting this are the iMac G3s and the eMac G4. The eMac has 256MB RAM, 40GB HDD, and a 700MHz processor. Two iMacs have 128MB RAM, 40GB HDD, and a 600MHz Processor. The other iMac is the same as the rest but has a 500MHz processor.
I am using ububntu 9.10,and have a cable modem internet connection. All I have is an ethernet cable given to me,and when plugged in a windows machine and fire a browser am redirected to default login page where i can login, but when i plug it into my linux machine,i cant get the same done. In network connections it doesnt shows my autoeth0, i have deleted my existing dsl settings(not autoeth0),made a new wired network,i doubt what should i put into MAC addrs field(i have put my machines mac given by lshw -c network.) What should I put in DHCP client id? Anyways when i click on network connections it says under my wired connections-device not configured properly.
View 6 Replies View RelatedAt the outset I would like to tell everyone that I am still relatively a newbie in linux. I use a usb mobile broadband data card to connect to the internet, and I recently purchased another desktop for my wife. Both of us do not share any files, but I do not have a router and was wondering if I could share my connection with her using a crossover cable.I did a lot of Googling around and tried various different things, I even followed another thread in the same forum but the most that I have got is my network manager saying that connection has been established. I am however not able to see her computer under my windows network and don't know how to proceed.I don't know where I am going wrong, and considering that my knowledge of networking is at below basement level, I would really appreciate any help in this regard.
View 2 Replies View RelatedI just got connected to Charter Cable Internet service a few days ago and I'm having a weird problem with my home network. Prior to this my network worked fine. On my network I have a desktop running Ubuntu 9.10/64 and Virtualbox with WinXP installed, an HTPC with Ubuntu 9.10/32 installed and a laptop dual booted with Ubuntu 9.10/32 and WinXP. The desktop and HTPC are hard wired to a wireless router and the laptop is wireless. The cable modem is hard wired to the router. I have samba installed and UFW is disabled. The problem is: with the cable modem turned off or on standby, all machines connect to each other and can transfer files, etc just fine but when I activate the cable modem all of the machines can connect to the Internet but the machines running Ubuntu can't connect to each other on the home network. If I boot the laptop into Windows, it can connect to the Linux machines just fine but if I boot it into Linux, it won't connect to the Linux machines but it can connect to the Internet and as far as the desktop, Ubuntu won't connect to the network but Windows running in the Virtualbox with bridged networking can connect to all of the machines.
View 2 Replies View RelatedIm a long time Ubuntu user (since 5.04), but networks were never my speciality, I have a desktop running 10.10, connected to the internet trough a US robotics modem (connection eth1), and i want to share its network with my laptop running win7, over a cat5 cable (connection eth0), but the problem is I dont seem to understand what i am doing wrong, what the missing steps required, or in which end is the problem (either ubuntu or windows side).
From what I could grasp was needed googling about the subject, i already set the eth0 connection to share with other computers (in network manager edit connections auto eth0 ipv4 configuration set to share with other computers). Also using the cli set eth0 for static ip using :
Code:
sudo ifconfig eth0 192.168.0.1 Now the question is what i am missing? or is everything needed already done and i just have to properly configure the win7 side (which i already checked several times)?
Here is my ifconfig output:
Code:
eth0 Link encap:Ethernet Endereo de HW 00:01:29:a6:55:fe
inet end.: 10.42.43.1 Bcast:10.42.43.255 Masc:255.255.255.0
endereo inet6: fe80::201:29ff:fea6:55fe/64 Escopo:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Mtrica:1
[Code]...
I am writing a simple script which will transmit files over a serial connection. I have simplified the setup to test the solution, so the final configuration will be a bit more complicated.
Current setup:
1. 2 RS232 com ports connected with a null modem in between.
2. Open minicom on both
3. Put in 19200,8,N,1 as parameters
4. Open text travels both ways
5. Files sent over Zmodem transfer well.
Both serial adapters are USB, but I tried it also with real com ports, and same story. For simplicity, I will call one adapter "receiving" and the other "sending" to signify from which side I want to send the files through zmodem.
Then I close minicom on the "sending" site without reseting the port (I have also tried setting everything up with stty)
On sending site:
Code:
I tried googling but no solution helps. Please do not try to suggest to use minicom on both sides, because this is going to be an unattended process in the end.
How to transfer a file with zmodem using rz and sz without minicom.
I am using a cable modem wired to my PC via ethernet. My ISP is Road Runner, through Time Warner Cable.
I entered my IP address, Netmask, and DNS Servers into the network, not using DHCP. This was how I was able to achieve a network connection.
I am connected to the modem, but I cannot get internet.
Here are my stats:
Ubuntu and Xubuntu read my Motorola Surfboard SBV5120 cable modem via USB "out of the box"; Puppy LInux doesn't. The computer I've run them on doesn't support ethernet, so it has to be via USB. what can I do to get Puppy online?
Computer: Systemax
Processor: AMD athlon
Memory: 189 Mb
Hard drive: 40 Gb
I cannot connect my Dell Inspiron 1300 through the NetworkManager "wired" connection, when I try to go direct to the cable modem. It fails to connect.
If I connect the cable modem to my (linksys WRT54GS) wireless router, and then connect my laptop to a wired port in the router, it connects in seconds, successfully.
This has happened to me 2 other times, when I tried to connect my laptop to a client's cable modem, because my client did not have a wireless router available, in their home.
My wireless works fine. This has me perplexed. I'm using Ubuntu 10.04 LTS and NetworkManager Applet 0.8
I've tried some things to see what is going on, such as "ifconfig" "dhclient" as well as modifying the "Auto eth0" parameters and adding my laptop's MAC address, etc. Results were no fix or solution. I feel like I'm headed down the wrong road. Would someone set me straight? I have a feeling this is simpler than I think.
Do I have to actually reset my own or someone's cable modem to get this to work? I don't want to do that unless there's no other way. Is there? Let me know what commands I can or should run.
i'm having problems connecting to the internet unless i manually enter the IP info.
automatic DHCP does not work. I'm on a dual boot machine vista/ubuntu 10.04 LTS connecting to the internet through a lynksys wireless g router and a cable modem.
Using ubuntu 10.10 (pinguy OS) i connected an ethernet cable from my girl's macbook pro to her lenovo ideapad s10-3t to transfer some DS9 episodes onto it. new enough to linux to have not been able to figure out how to access the files on the mac, so i disconnected the ethernet, and the wireless hasn't worked since. tried everything i know, and googling for a while (as well as searching again on this forum) to no avail.
Just before linking the 2 computers via ethernet, the wireless worked fine on the ideapad, always had; but not so after the ethernet connection that did nothing other than apparently kill the wireless. an "lshw -C network" command tells me i have a BCM4313 wireless card, and *-network UNCLAIMED. also, if i launch "install additional drivers", i see that the proprietary driver is not active.
How could merely plugging in an ethernet cable that happened to be conncected to a MBP running OSX.6 do that? and will that happen again? i thought linux was supposed to play real nice with other OS's, so why did a simple file transfer kill my wireless connectivity? i have no access to internet via ethernet cable, so i cannot just download the driver i need now. shouldn't it still be in the computer still? somewhere? is there a simple solution to this, or has the wireless driver been wiped out by plugging in the ethernet? is this a bug that should be reported?
I have fedora 12 installed in my laptop. Can anyone plz tell me how to connect nokia E51's modem ( via. Data Cable) to access GPRS !
View 2 Replies View RelatedRunning 2.6.29-gentoo-r1 on a Sun Ultrasparc 10 with a Sun Happy Meal on eth0 connected directly to my cable modem. Intermittently, with a frequency between a few hours and a few days, I lose internet connectivity. Running ifconfig eth0 indicates all is well and I have a valid IP address but I cannot even ping the cable modem's management address; pings to 127.0.0.1 and eth0's IP address do get a reply but no other address I've tried does. I can 'fix' the problem by issuing
Code:
If I check the CM logs, it appears that it has rebooted itself prior to the loss of connectivity. The strange thing is that the incoming traffic doesn't seem to be affected by this, my PSAD log is full of incoming scans even during the periods when I can't connect to the net. I suspect this is an ISP problem (they own the CM);
Running Gentoo with kernel 2.6.29 on a Sparc Ultra 10. I'm having problems with my cable modem connection failing, so I've added a static route that enables me to log into the modem's diagnostics page at 192.168.100.1 when the connection drops; my /etc/conf.d/net looks like this (with the comment lines removed).
Code:
dns_domain_lo="MYNETWORK"
config_eth1=("192.168.0.1 netmask 255.255.255.0 broadcast 192.168.0.255")
config_eth0=("dhcp")
routes_eth0=(
"192.168.100.1/32 via 0.0.0.0"
) dhcpcd_eth0="-N"
This works but after a period of several hours to several days, this static route disappears from the routing table.
My broadband internet connection came with a Nokia-Seimens C2110 Adsl modem. Please help me connect the modem through USB cable as the ethernet card is used to connect my computer(Asus- P5RD2 VM motherboard) to a different computer on LAN. I am in a fix and have no clue how to proceed.
View 1 Replies View RelatedI have a sprint usb 3g modem that plugs in via usb. I want to be able to share that Internet though an Ethernet port so I can connect another PC or my playstation so I can steam movies or just use the INTERNET on another puter. Iv tried lots of stuff I found on Internet like firestarter for one but it doesn't want to set up right.
View 4 Replies View Relatedi want to ask a question. sometimes i use a gprs modem to connect to the net. the gprs modem uses the usb port. i've connected this pc to another machine through crossover cable. the problem is that when there are two active connections, firefox can't load anything. also how can i share the gprs modem with my other pc that is connected via crossover?
PS. in my active network connections it shows:
eth0- the NIC
and auto eth1 - the gprs modem
i have also tried to change the firefox preferences but to no avail.
Both my computers run on FC11.
I use Opensuse 11.2 & Edge/Gprs Modem to connect Internet.I configured /etc/wvdial.conf & /etc/resolv.conf. Now I can connect Internet using this command "wvdial MYNET" in terminal.Now I want to share my internet using Lan card & Netgear Router. If i connect my PC with Router using wire & change option ON BOOT find this device in ifup then it'll show in ifconfig command.
My Router IP : 192.168.0.1 & It gives my PC an IP automatically : 192.168.0.2
I can ping my router.. even I can browse Router Admin page in browser. No problem there.But now If i want to connect my net using wvdial command... net connected... but no data passing!!! If i disable Lan card in ifup then Edge/Gprs net connection again OK!
For my broadband Internet I have several computers connected by cable to a Netgear DG834Gv5 router which has its own firewall.I have the wireless turned off by choice.My desktop and laptop are Linux only. (Ubuntu lucid lynx) I use the same username and password (very strong password) on both.What I want to know is can I set things up so I can browse and copy files between the computers using say nautilus on either computer?if not nautilus then I would happy to be able to do the same via a terminal window.I am not necessarily wanting to be told how but either what to Google for or where to find it.
View 2 Replies View RelatedI am wanting a computer with an external dialup modem (ppp0 modem through a com port /dev/ttys1) to act as a gateway to the internet, forwarding internet traffic through ethernet (eth0 is set to static 192.168.2.2) to a router (the router is 192.168.2.1) where it will be broadcast to other wireless computers like my laptop (192.168.2.3). I've had this setup until recently when the gateway computer (the one with the modem) died. Now I'm replacing that machine with another box and an install of Ubuntu 10.10 but so far things aren't working for me.
Success so far:I have dialup access working on the new box. Took me a while to work out the configuration for getting dialup working, though the IP address is Dynamic (or it won't stay connected), "Check carrier line" is off, and "Ignore Terminal Strings (stupid mode)" is on in order to successfully connect and stay connected to my ISP. I also had to make my normal (non-root) user "lancer" a member of the "pid" group (the reboot) in order to use gnome-ppp as non-root. The laptop (192.168.2.3) is successfully connecting to the router (192.168.2.1) as I can see the router configuration page when I type http://192.168.2.1 into the laptop's web browser. This setup is unchanged from how I had it before when this was previously working and I don't want to change how the router itself is set up. What I want is to know what to fix in the new box in order to get it connected to the router (through ethernet) and bridging the internet through.
My problem is that whenever I plug in the eth0 from the gateway (192.168.2.2) to the router (192.168.2.1), Ubuntu's automatic plug-me-in network detection kicks in and I find my dialup no longer working through some kind of IP conflict (at least that's what I think it is). Maybe I don't have the "gateway" correctly assigned? (in the gateway computer for the ethernet connection, I had it pointing to itself as I don't know what to put for "gateway IP" as that is automatic So, just to check my connection, here I am pinging google (from the gateway computer which has the dialup modem) once a dialup connection has been made.
Code:
lancer@lancer-desktop:~$ ping www.google.com
PING www.l.google.com (74.125.237.17) 56(84) bytes of data.
64 bytes from 74.125.237.17: icmp_req=1 ttl=55 time=179 ms
64 bytes from 74.125.237.17: icmp_req=2 ttl=55 time=176 ms
64 bytes from 74.125.237.17: icmp_req=3 ttl=55 time=158 ms
[Code]...
What do I need to do in order to make Ubuntu of my gateway computer stay connected to my dialup but also simultaneously share an ethernet LAN to my wireless router and feed traffic to the other computers from there? I have googled this but some of the most promising instruction (e.g. http://www.ubuntugeek.com/sharing-in...in-ubuntu.html) call for packages like dnsmasq or ipmasq which seem defunct now in Ubuntu 10.10. Other pages seem to suggest dual-networks "can't be done" in Ubuntu [URL].. (what!?! I had it before my other gateway died)
I want to configure my ADSL but I don't know what should I do. Can you explain me How can I configure it?(I use fc10, ethernet cable <Asus Am608 ADSL modem)
View 9 Replies View RelatedI got a new cable modem so I could get rid of the one I've been leasing from the cable company. It is a Motorola sb6120. Everything is fine with the ISP, it's approved for operation on their network, the only hitch was I had to use my Windows laptop to run their activation software.
At any rate, with the new modem installed, I hop on my Linux box and go to work. I'm seeing some terrible delays in looking up names. When I look with firebug, all the dns lookups for new names are taking 15+ seconds. First I just think maybe the names aren't cached or something is weird for a minute and it will get better, but no. After several restarts and then a couple days persevering with the new cable modem, all DNS queries are still terribly slow (including zypper, mail client, web client).
Suddenly I remember an issue I was having with, I believe version 11.1 when I first installed it. For just the computer on my network with a fixed IP address, DNS resolution was slow like this and if I disabled IPv6 then all was well. I believe there was even a patch issued back then for gethostbyname() that was supposed to fix the issue? So, when I disable IPv6, DNS lookup is back to normal. The two Linux computers on my network had been working fine with IPv6 and the old modem, though, and the Windows box is still working fine even with the new modem.
I can disable IPv6 and make it fast again, but really why should I have to?
I have a CentOS system running. I want to get mail off it to my yahoo account.
I did a test mailx command and it goes out of the queue but never gets to my yahoo mail.
I am using a cable modem.
I can go out to the Internet so I know I have a valid connection.
I am guessing I need to set something up so the cable company will relay my mail for me.
I know i can pull pop mail down and sen it using my account.
Do I need to configure something in the sendmail.cf file to do this?
I just went into my email and say this ...patial msg included...
(reason: 553 5.7.1 [BL21] Connections will not be accepted from 98.249.136.1 9, because the ip is in Spamhaus's list; see [url])
I installed slackware 13.1 a couple of days ago. I am a complete linux newbie..I am able to connect to internet from windows using the USB cable of my modem..but this modem is not detected in linux..is there any option to make linux detect it?
I have a pentium 3, 1 GHz processor 256 RAM..and the info below i got from my terminal..
lsusb output
Code:
Code:
And here is some information about my modem
Code:
Features:
-Complies with IEEE 802.3, IEEE 802.3u standards
-One 10/100Mbps auto-negotiation RJ45 port supporting auto MDI/MDIX, 1 RJ11 port, 1 USB port
-Built-in firewall
-Compatible with major ISP lines
-Fast internet access
-Supports bridge and NAT router mode
-Complies with ADSL protocols (ADSL/ADSL2/ADSL2+)
-Easy configuration
-Quick response semi-conductive surge protect circuit, provides reliable ESD and surge-protect function
-Supports firmware upgrade
-Built-in DHCP server
I have been testing with "Add a physical serial port in Polled Mode to a VM using a Null Modem cable".I have been using HP ILOM for a while and need u guys help with "can I Connect the null modem serial cable from server port to the desktop which act as a terminal through ilom?
View 1 Replies View RelatedA netmap scan of my WAN IP address (cable modem) shows;
23/tcp open telnet?
8080/tcp open tcpwrapped
I've called Linksys and Netgear and they have said there is no user adjustable configuration allowed for the Cable Modems.
How am I supposed to close the open ports if the manufacturer doesn't allow access ?
I snaptic installed xmacro. I do not see it show up anywhere. Lost. I need a macro that can record keystrokes to reset my cable/router modem combo. I now use autohotkey. But I cannot virtual machine this, because it would need to raise up a ms windows explorer, something that cannot be done in a virtual machine on guest OS.
View 1 Replies View RelatedCan Cat5e RJ45 connector crimper be used for Cat 6 connector because I heard cat 6 connector is different from cat 5e connector and also same question for cable tester can cat5e cable tester be used for cat 6 cable?
View 1 Replies View RelatedRight now I am using some software to emulate a null modem serial cable on my Windows computer connected to itself. For development purposes I need to have a null modem connection to a linux computer from a windows host. Is there any method of doing this virtually?
View 2 Replies View Related