Ubuntu Networking :: Router Not Passing On DNS Address?
Feb 2, 2011
I'm using an ubuntu machine to route internet to my main PC. I think I finally got it working with DHCP and all, but there's still a slight problem. DNS does not work! My /etc/dhcp3/dhcpd.conf file contains the following lines:
Code:
default-lease-time 600;
max-lease-time 7200;
option subnet-mask 255.255.255.0;
option broadcast-address 192.168.0.255;
[Code].....
I am currently only able to post on this forum because I copied /etc/resolv.conf from my server to my main machine. Now DNS is working. But it should update automatically, right? Currently, this isn't working.
If possible, I'd like it most if I wouldn't have to hardcode the DNS servers in /etc/dhcp3/dhcpd.conf either, but that the server would just relay the DNS adress it has gotten itself!
View 7 Replies
ADVERTISEMENT
Sep 1, 2011
I have read in a forum that a computer can have the same MAC Address with its router in the sane LAN but how is that possible? Isn't every MAC unique? Also I have not understood, when we send a packet to a PC that is not in our LAN the packet should have the IP Address or the MAC Address of the computer that we want to send?
View 3 Replies
View Related
Aug 24, 2010
us robotics router, trying to access 192.168.2.1, worked on windows xp, just switched to lucidi have tried using both firefox and chrome, neither will access my router
View 7 Replies
View Related
Jan 24, 2009
I noticed that my internet connection wasn't automatically brought up each time I logged into Fedora so I opened the system-config-network tool and edited my network adapter by checking the box marked "automatically start at boot/login." To my surprise, the connection went down and upon trying to click on the device to let the manager bring up the connection the greyed-out phrase "device not managed" appeared underneath the device name and wouldn't allow me to connect.
Even when I used ifconfig/dhclient to get the connection up nothing happened. I could get the router to assign an IP address through DHCP, pinged a few sites to make sure it was legit, but still couldn't use firefox to browse anything. Seems as if network manager GUI is conflicting with command line attempts to bring the network up. I'd like to permanently disable system-config-network if possible because it's acting screwy!
View 5 Replies
View Related
Jul 7, 2011
I have just installled fedora, and I am puzzled by dhclient-script. Because it gives the router ip as nameserver 192.168.0.1. I have had other linux distro on same machine that resolves the correct nameserver without any configuring.
Does anyone know how to get your ISP:s nameservers instead in /etc/resolv.conf when running dhclient from CLI? I have thought about edit /sbin/dhclient-script. But if that is the case. Which option should I edit?
Quote:
My system
OS=Fedora 15
Kernel=Linux fedora_15 2.6.38.8-32.fc15.i686.PAE #1 SMP Mon Jun 13 19:55:27 UTC 2011 i686 i686 i386 GNU/Linux
Router =DLINK dir 100 (IP 192.168.0.1)
View 5 Replies
View Related
Jul 6, 2010
I'm running Ubuntu 10.04 and my setup is as follows:
As you can see, I am directly connected to router 192.168.25.1, and so my ip address is 192.168.25.101. I want my ip address to be 192.168.13.101, and make router 192.168.13.1 my gateway router. Is this possible under the current physical layout (I do not want to have to connect directly into 192.168.13.1, but keep my computer where it is at)?
When I run tracepath, it shows 192.168.13.1 is one hop away.
What I've tried:
The problem is under this manual setup, I cannot ping 192.168.13.1 and running command netstat -rn returns the following:
View 2 Replies
View Related
Jan 31, 2010
I've only been using linux for a few days so I don't know all the tricks. I'm pretty savy configuring windows networks however.My adapter is (according to windows) a: CNet PRO200WL PCI fast ethernet adapterLinux says it is a: 21x4x DEC-tulip compatible 10/100 EthernetI do seem to be getting an ip address from the DHCP router, but I cannout ping any other ips or connect to the internet.I've tried a bunch of different options, switching things back and forth, but it still doesn't work, and honestly i don't even know what some of the options mean.
ALSO, if this helps:
paladin:~ # ifconfig eth0
Eth0 Link encap:Ethernet HWaddr 00:08:A1:03:3C:99
[code]....
View 14 Replies
View Related
Aug 31, 2011
I have been struggling to get FC15 to act as an IPv6 router for a while now, am sure I am missing something trivial.. The idea is that I have a ppp / adsl connection (this works fine), use the wireless card on my pc with hostapd and dhcpd to provide connections to other pcs (works fine), and radvd to delegate ipv6 addresses.
The issue seem to be that as soon as I turn on ipv6 forwarding (net.ipv6.conf.all.forwarding =1), the ppp connection no longer gets an IPv6 address. This means the router cannot ping any ipv6 address outside my network.
If I disable ipv6 routing, my router gets an IPv6 address on its ppp connection, and can ping things such as ipv6.google.com just fine, however (of course) no packets are forwarded from my network and radvd complains that forwarding is disabled.
View 1 Replies
View Related
Jul 15, 2010
I need to obtain daily dynamic IP address from my router for remote user. In order to get into the router page, I need to login to it with ID and password.
Can I tell the server to do this every time it started up to login to router and extract the ip address and send out via email?
The router can only access through web interface and below is what I copied from browser.
View 8 Replies
View Related
May 29, 2014
I have 2 PCs, each running Oracle VirtualBox with about 30VMs installed and standing on the same table
On shopping router I found TP-Link
TL-WR741ND
150Mbps Wireless N Router
[URL] ....
How can it assign 30 IP address to each PC?
View 0 Replies
View Related
Apr 13, 2010
Because of the configuration of my house, I need two routers.I have a DLink ADSL router as my main router and the Belkin N1 as my repeater.I have set up the IP address in the Belkin to be 10.1.1.10 - my DLink is 10.1.1.1. I have disable the dhcp in the Belkin and set the DNS as ISP provided. [URL]..I have set the channel to 11 and in the Ubuntu Network Manger I have set the IPV4 to Link Local Only. I can see the Belkin and connect with my PC.but it will not take me through to the internet.
View 9 Replies
View Related
Aug 18, 2011
I get assigned an IP from the university's server. Every now and then, a student will plug in his router to the network trying to get wifi in his/her room.
And by doing so will start assigning IPs on the network, while rendering useless the university dhcp server, which has to cope with a higher number of pc's.
How can I specify to dhclient (or the linux system in general) NOT TO obtain IP addresses given by a specific mac address ?
View 7 Replies
View Related
Jun 18, 2011
I want to set up a Linux box as a wireless router to replace our existing Netgear WNR1000 router, as I believe the Netgear does not support the coming IPv6 protocol. Unfortunately, it is not flashable with OpenWRT or DD-WRT presently.
As we have Comcast, our cable modem acts as a dumb modem according to the customer support guy I talked to, and our router is the one that asks for the IP address from DHCP. Thus, when Comcast switches over to IPv6, I don't believe my existing router would work, correct?
My idea is to take a Linux box and put two NICs and a wireless adapter in it, using IPCop or Smoothwall to set up a router. I could then enable IPv6 support for when we have IPv6 with Comcast. Is that possible? Would there be a way to get BIND to hand out private IP addresses in the same subnet on the both the LAN NIC and the wireless card?
View 1 Replies
View Related
Nov 6, 2009
I have a desktop PC running Ubuntu 9.10 and Windows 7, and a Eee PC 701 laptop running EasyPeasy Ubuntu 9.04. I'd like to connect the desktop to the laptop with a wired connection (eth0), then the laptop to my ADSL router using wireless (ath0).
I have a crossover ethernet cable (I bought on ebay). I have set up my laptop with a static IP address on my LAN and it uses OpenDNS.
I have added this to /etc/sysctl.conf on the laptop:
net.ipv4.ip_forward=1
Then I tried this on the laptop:
sudo iptables --table nat --append POSTROUTING --out-interface ath0 -j MASQUERADE
sudo iptables --append FORWARD --in-interface eth0 -j ACCEPT
This is a variation on what I found on other sites describing how to set up a router. I don't understand iptables very well, but I gather that the above two lines should set up forwarding so that traffic from my router to the laptop will be forwarded to the desktop, and vice versa.
But this doesn't work. The connection doesn't even establish between the laptop and the desktop.
View 12 Replies
View Related
Apr 24, 2010
I'm having trouble getting my network set up the way that I want it/had it. You see, when I first set up my network, I just had my cable modem going directly to my standard wired router (A D-Link DI-604), which had DHCP,and was connected to all of the computers on my network. I had one switch hooked up to one of the ports of the router, but this was a regular switch, and it would not try to assign IP addresses, it would just pass through the DHCP info as I wanted.
Now however, my network setup has changed. My room mate and I both got laptops, and we decided that we wanted to have wireless access so we didn't have to constantly plug in to the router.
Now my network is set up like this: The modem is hooked up to the router(DI-604), which is hooked up on the LAN side to our computers, our switch (which is hooked up to 3 more computers), and to a wireless router card (A Gigabyte GN-BC01).
The wireless router card has two jacks for ethernet. One for WAN, and one for LAN. The LAN side we have plugged only into the computer in which the card is installed.
Now the problem is this: The wireless router card comes with DHCP by default, and it's assigning addresses to the laptops and to the computer hat it's in, and worse, the IP addresses are on a different subnet than that of the main dlink router. The Main (dlink) router assigns addresses from 192.168.0.1 (itself) to 192.168.0.254, while the wireless router card assigns addresses from 192.168.1.1 to 192.168.1.254 (itself).
Because of this, I cannot access services on the wireless network from my wired network or vice versa. The first thing I tried was setting the card to assign addresses from 192.168.0.12 to 192.168.0.253, however it just said "internal error" when I tried to do this. I decided that this may be because it sees that it was being assigned an address on it's WAN side on the same subnet. So the next thing I tried was disabling DHCP and setting the "LAN IP Address" to 192.168.0.12, hoping that the DHCP would just go through the card, like a switch. I would have set the LAN IP address to be assigned by DHCP, but this was not an option, so I decided that'd be the best thing to set it to.
Once again however, setting the LAN ip address to an address on the same subnet as that of the IP assigned to it's WAN side caused it to report an "internal error". I verified that this was the issue by setting the LAN address to several other private IP addresses to test (I.E. 10.0.0.1, 192.168.3.1, 192.168.5.12).
My question then really is: How do I set up both routers so that I can access services and computers from each network from the other network. Should I set them with different subnets and set the gateway on the wireless network to the main router? To the wireless router card? Should I put them on the same subnet? Will it know how to communicate?
Here is a link to (picture) my network diagram. Network Diagram
View 2 Replies
View Related
Feb 24, 2010
I have an open WEP wireless internet connection with a security key. KNetworkManager can never obtain an IP address from my wireless router, but I know that the router works because Windows can connect correctly and Ubuntu's NetworkManager can connection correctly. Does anyone know what is happening? KNetworkManager just asks for my security again and again and again after it fails to connect.
View 8 Replies
View Related
Feb 24, 2010
Currently my OS is Ubuntu 9.04 Jaunty Jackalope Desktop OS and my web server is Apache2. I have a public address 60.x.y.z and my pc local address is 10.x.y.z. I have a web app in my Apache2 which currently run in localhost(10.x.y.z).
I would like to enable the web app so that it could be browse from outside. I know there maybe some port forwarding process and some commands involved in order to do that. But I have no idea on the steps to do that.
View 5 Replies
View Related
Mar 26, 2009
These r IP provided by my ISP that i've put on Fedora 8:
WAN IP:xxx.xxx.xxx.17 (eth0)
Subnet:255.255.255.252
Gateway:xxx.xxx.xxx.18
Valid static(public) IP set of 2:
IP:xxx.xxx.xxx.147 & 148 (eth1, eth2)
Subnet:255.255.255.240
i want to run xxx.xxx.xxx.147 as a web server & xxx.xxx.xxx.148 as a ftp server. but I'm able to ping only xxx.xxx.xxx.17(WAN IP) from outside world. Can any1 tell me that how can i bring my 147 & 148 IP online without router.
View 6 Replies
View Related
Dec 16, 2010
Version 10.04 LTS. Installed desktop version and network worked but I needed a static IP address and the install configures for a DHCP configured address. I tried changing to static address using the System->Preferences->Network Connections application but was unable to get the system to come up with the network up.
So I manually modified the /etc/network/interfaces and the /etc/resolv.conf files. I restart the system but when I do an ifconfig, I don't see a configured IP address on eth0 (only the loopback address). If I run /sbin/ifup eth0 everything then works fine and ifconfig shows the correct address bound to eth0.
My files are as follows:
View 2 Replies
View Related
Mar 12, 2011
I'm running Ubuntu 10.10 and I'm having problems trying to assign it a static IP address. No matter what I put in the Preferences->Networking area (identifying the interface as Manual)... it still will query DHCP for an address if I run the dhclient command. I'm using to using ubuntu server where I just set the IP in the interfaces config file.
View 1 Replies
View Related
Jun 25, 2010
We have a ubuntu machine on the network with number of users in it. Basically, when other users connect via telnet i want then to get particular messages depending on the user. The message will be set by the administrator or a particular user with privs. Similarly we also need a to-do app via which users can update their work and see each others progress . Its all in a local network. Do tell what would be the best way to do it!
View 2 Replies
View Related
Mar 29, 2011
I am having an issue with pureftpd and the way it handles passive mode. Here is a link to a discussion on filezilla.
[URL]
Basically the problem I have is that the Ubuntu Server is not passing the right IP address. It passes the internal "unrecognized IP address"
How do I set up Ubuntu to know it external IP address and pas it during a passive mode FTP connection?
View 1 Replies
View Related
May 12, 2011
I am working on implementing a protocol on NS2.34 .I really need help to solve this problem . Actually , I don't now whether the problem is generated by the tcl code or the c++ code when I run the simulation, I get this result :
Code:
num_nodes is set 64
INITIALIZE THE LIST xListHead
34
45
channel.cc:sendUp - Calc highestAntennaZ_ and distCST_
highestAntennaZ_ = 1.5, distCST_ = 550.0
SORTING LISTS ...DONE!
code....
View 1 Replies
View Related
Apr 24, 2010
Consider the following program:
Code:
#include <stdio.h>
#include <stdint.h>
[code]...
View 2 Replies
View Related
May 7, 2010
I am running my own Postfix mail server. Some time ago I noticed that most email was rejected because of the server's dynamic IP address. So I got a fixed IP address. However then I noticed that some mails got rejected due to failing the reverse DNS check. So my ISP told me to get a range of IP addresses and they could then create a PTR record for one of those addresses. That is now running but it turns out that the IP address used for the PTR record is a ... dynamic IP address. So Spamhaus PBL rejects my emails again.
View 1 Replies
View Related
Apr 1, 2011
Using 10.04 and x11vnc I'm finding that upper case characters are being sent as lower case. I've tried multiple keyboard configurations with no success
View 1 Replies
View Related
Oct 6, 2010
In my job I use some ethernet embedded devices. They take an ip address from dhcp server or auto ip. I only know mac address.How can I obtain ip from mac address? In other words I need a rarp packet generator.
View 6 Replies
View Related
Jan 23, 2011
I did some playing around changing up the configuration of my server and now cannot pass traffic through to port 22. I have since restored everything back to the way it was but am still not able to ssh into the server.
nmap only shows port 80 and 5222 open. Both ports that I want open. However I am unable to get 22 to pass.
iptables -nL shows
http://www.theprepared.com/images/tech/iptables_nL.PNG
netstat -an |grep 22 shows
http://www.theprepared.com/images/tech/netstat.PNG
I've tried clearing the routing table with the following which did no good.
ip route flush table main
Can somone point me in the right direction?
View 1 Replies
View Related
Jun 7, 2009
I have a few external IP's assigned to me by my ISP. I have IPcop as my router/firewall. I am wondering how to bind 1 of my external ip's to my internal ip address. So I do not have to port forward, etc. For Example, 77.77.77.77 to 192.168.1.123 and on the server it see's the external IP address.
View 2 Replies
View Related
Oct 28, 2010
I dont know for what reason, since 2 days, I started having this message whenever I try to start httpd.I commented "Listen 443", restarted httpd started correctly. I needed to comment "listen 443" in order to be able to start httpdWhat is strange is when I do
Code:
telnet mylinux 443
it responds
[code]...
View 9 Replies
View Related
