i done desktop config in ubuntu server 11.04 and connected via tightvnc,uvnc and in remote desktop viewer from another ubuntu machine also. I am not able to access(connect) the server in GUI mode(when monitor is removed) but i putty is working fine in cmd line.
View 1 RepliesI am running CentOS 5.1 on VMware on Win 7 On CentOS I added Bridged network adapter and the server is connected to internet without any problems, but when I telnet any server on port 25 I get connection timeout.
Code:
telnet f.mx.mail.yahoo.com 25
Trying 98.137.54.237...
telnet: connect to address 98.137.54.237: Connection timed out
telnet: Unable to connect to remote host: Connection timed out
I stopped all servers, iptables and sendmail on the linux server and the firewalls on the win 7 but still getting the same error! I added new network adapter ( host-only ) and tried to telnet the win machine from vmware Linux but I got connection refused
Code:
telnet 192.168.71.1 25
Trying 192.168.71.1...
telnet: connect to address 192.168.71.1: Connection refused
telnet: Unable to connect to remote host: Connection refused
[code]....
When i am trying to telnet to a machine connected in our LAN ..
telnet: Unable to connect to remote host: Connection refused
What's the reason for this? how do i establish a connection? I am using ubuntu 10.04.
telnet localhost the output is...
Trying 127.0.0.1...
telnet: connect to address 127.0.0.1: Connection refused
telnet: Unable to connect to remote host: Connection refused
I don't understand what is the problem. Its not configured properly how do i configure it?
I'm trying to connect with my server via telnet, but when i sent the command (telnet xxx.xxx.xxx.xxx Port) doesn't works and shows then follow error: Unable to connect to remote host: Connection refused, It happens with any port. Is strange but my telnet services works (telnet xxx.xxx.xxx.xxx), In addition, i tried with firewall enabled and disabled and the problem still happens. My centOS run on virtualbox.
View 3 Replies View RelatedFriday night I was working on some networking stuff between my two Fedora 14 boxes. I have my laptop and my desktop. on both machines I have "system-config-firewall 1.2.27" and "iptables" (i believe both come standard on F14?) I kept getting the same message as seen below before realizing perhaps I should check my firewall!
I added a rule for incoming and outgoing traffic on port 22 and was able to get in with no problems at all! however today I can't ssh into anything... I can't use "Remote Desktop Viewer 2.31.4" to vnc into the machine anymore. I can't remember the exact error message at this time, it's something close to "Connection was terminated" or "Unable to connect" I can update this message later.
last night I foolishly uninstalled the system-config-firewall and then uninstalled iptables to see if it was a simple firewall issue.... totally hosed my system <insert smiley!>
After reinstalling and realizing I didn't backup my documents <insert smiley!...again...> I started reinstalling all of my applications. I'm still unable to use ssh and I've tried to ssh my own computer.
Is this possible?
# ssh 127.0.0.1
ssh: connect to host 127.0.0.1 port 22: Connection refused
I am facing connection refused error 111 in TCP client server program, in android native code which in C , but if code is in JAVA it works fine, but i want to continue in C only, in manifest file i have given permission and ip, port is correct .What am doing wrong?? or is their any network setting?? am using UBUNTU 10.04and If both client server Linux pc it works fine. only if android emulator becomes client then am getting connection refused
View 1 Replies View Relatedlpr: can't connect to remote host (127.0.0.1): Connection refused
[root@l-GZ:/]# usb 1-1: new full speed USB device using sl811-hcd and address 3
I am using TomCat6 with Ubuntu Server 9.10 x64. I successfully configured to iptables to redirect the port "443" to "8443" (Tomcat SSL), using this command:
[code]...
when i try a telnet to a host like that: telnet 10.10.10.10 1234 i got this: telnet: Unable to connect to remote host: Connection refused.
1/ does this mean that the problem is not due to a firewall, but that the host 10.10.10.10 doesn't listen on the port 1234? other way does this mean that my firewall is authorizing traffic on the port 1234?
and when i try a telnet on another port like that: telnet 10.10.10.10 1235 i get: Trying 10.10.10.10 ...
in this case this
2/ does this mean that the firewall is blocking the traffic between my host and the 10.10.10.10 on the port 1235?
My system is Ubuntu 11Before I typed "telnet localhost" or "telnet localhost 23". I have make this work below:$sudo apt-get install xinetd$vim /etc/xinetd.conf
defaults{
instances=60
log_type=SYSLOGauthpriv
[code]....
I did followings:
Code:
But got:
Code:
But as I tried:
Code:
It's OK.
Can I use apcupsd to monitor my smart-ups 2200 without it being connected to a server? I have set the TCP info on the APC and can telnet into it, but I'm kinda confused by what I've been reading in the apcupsd documentation.
If someone can tell me about there experience doing this and best practice that would be awesome.
I am doing some R&D on 11g RMAN in oracle at home. i have installed oracle enterprise linux and i have installed oracle software. when i am trying to configure listener, it is error-ed out. i have verified that telnet with the port is not working and i am seeing connection refused error.
View 3 Replies View Relatedvsftpd not working on my CentOS system. I tried logging in using FileZilla but the error message was: Connection attempt failed with "ECONNREFUSED - Connection refused by server".
View 7 Replies View RelatedI'm trying to create a PAN (Personal Area Network) using a laptop (Siragon ML-1040) and my desktop computer, but I get the Connection Refused (111) error.
Blueman doesn't detect any network service between the two computers unless I start PAND on one of them and then it detects the NAP service. That, only after I enable the NAP/Workgroup services on the Services submenu in Blueman. However, it doesn't work neither with the NM plugins or without them (dhclient and that other one I can't remember the name of).
Any clues over here? I'm using pand 4.91 and blueman.
I need to access all PCs in our LAN via ssh from our server in order to do some maintenance. All of them have Ubuntu or Kubuntu Lucid Lynx. Some of the PCs allow this access with no problems, but most of them not. They just answer "Connection refused". I realized that these PCs don't start sshd at startup. If I type "sudo service ssh start" manually in these PCs then sshd starts and all works. But I need it to be started automatically.
I tried some workarounds to solve with no success. I always tried to run a script at startup that could start ssh. If I write a script with this single command inside (service ssh start) and execute it as root, it doesn't work! It doesn't start ssh. But if I execute the same command directly in the command line, it works. I don't understand this behaviour. Also I don't understant why it doesn't happen to ALL the computers. Some of them start ssh at startup with no problems.
I have 4 boxes on a local network: 2 with XP only, 1 with Ubuntu 9.10 only, and 1 with both. All boxes can share folders, set up with share-admin instead of using Nautilus right-click properties for each folder. I can see and control the remote desktops on all boxes, to all other boxes, from all other boxes,with one exception: I can only access the XP desktop on the dual boot box, not the Ubuntu desktop. When I try I get: "Connection to host 192.168.1.102 was closed." I am refused access to the Ubuntu desktop in this manner from both the other Ubuntu machine, and from both XP machines.
My setups are basically plain vanilla with routine installs of Ubuntu 9.10. On the XP machines I am using TightVNC on the XP machines to view both other XP desktops, and the Ubuntu desktop that is accessible. On both Ubuntu setups I am using (I suppose) vino and vinagre, and have completely re-installed what I think is the relevant software. There is no firewall running on the Ubuntu dual boot, when I check ufw. For reasons I cannot determine the inaccessible Ubuntu desktop is not providing its own address but instead in the Remote Desktop config dialogue it identifies itself as 27.0.0.1 which I think is the loopback id. I know so little about this sort of networking that I am not giving all relevant info, but I still thought I'd try.
configure nagios to monitor custom port on a remote linux server..
View 5 Replies View RelatedIm running a dedicated server for our website(and a few other things) and for some reason, the website suddenly started giving everyone trying to access it a 500 internal server error.
When I went to correct this problem through ssh, it says "connection refused". We don't have an ftp account and webmin isn't working either, is there any other way we can get into the server?
We are running a Apache/2.2.3 (CentOS) Server.
I am merely trying to change the port for my ssh server.However it isn't changing.I edited my ssh_config file to:
Code:
# This is the ssh client system-wide configuration file. See
# ssh_config(5) for more information. This file provides defaults for[code]...
When i try to connect to my server via port 443 i get a connection refused error. However when i try to connect via port 22 it connects. Since that didn't work, i tried restarting the entire server.To restate, i changed the config file and restarted ssh then the computer, however the port didn't change.Ohh and yes my router is set to port forwarding on port 443, though it doesn't matter since I'm inside the network.
i am facing a problem with my mail server,i get an error when sending mail to a specific domain group;
Aug 18 06:41:02 mycompany2 sendmail[16745]: n7I1Ab9m016743: mail.xyz.in.: SMTP DATA-2 protocol error: 571 Delivery not authorized, message refused
Aug 18 06:41:02 mycompany2 sendmail[16745]: n7I1Ab9m016743: to=<feedback@xyz.in>, delay=00:00:25, xdelay=00:00:24, mailer=esmtp, pri=166397, relay=mail.xyz.in. [xxx.xxx.xxx.xxx], dsn=5.5.0, stat=Remote protocol error
I am experiencing a problem with Nagios running some checks on our Ubuntu 10.04 servers.
we have 16 Nos HDD in each servers. These HDD's are checking by nagios with CPU and users.
For whatever reason, all of the checks will come up with the response: "Connection refused by host".
We have checked the server at the time of occurence and all seems fine. No memory issues, no CPU issues etc.
Then within 5-10 minutes the problem goes away.
ERROR:Connection refused (111)when i change the password.I have a freebsd dovecot server.
View 1 Replies View Relatedat the computer shop we have an ubuntu 9.10 server that we log into via ssh or webmin today i was trying to ssh into the machine and got connection refused, so i logged into webmin and found the ssh server not running when i tried to start with webmin it i got the error
Code: failed to start ssh server * /dev/null not a character device went over to the shell command part of webmin and issued ls /dev -l and looked at the output and found something of concern
[Code]....
I have configured openssh 5.8p2 with centos 5.6. My sftp is working fine with chroot environment but i am having problem with SCP. I am dealing with muliti Redhat servers. When i try to transfer data from other linux server through scp it gives connection refused. For e.g ssh 5.8 is configured on new server and i want to transfer files from old server which is using openssh 4.3 version.i created same username and password on new server as on old server.My sftp users on new server has no shell access but only sftp access. When i try to scp from old server to new server it gives error connection refused. Is the below configuration only for sftp and can't scp? According to google the configurations i found are for scp and sftp. Do i need to generate ssh keys by giving users on new server shell access, once created then stop shell access again, as i dont want to give shell access permanent for security reasons? but i want to use ssh keys for more security as well.
Port 22
PermitRootLogin no
1.override default of no subsystems[code].....
I'm trying to make an SSH script for my place of employment. This script, I want to go out to the server hostnames we have specified (in another file) and change a users account password. We use Kerberized telnet, so if telnet root hostname fails, I want it to use ssh username hostname and use the old password (specified). If both fail, I want it to ask the user what the port should be and input the port in the ssh command.
But I'm having a issue having it try telnet root hostname and if it fails then, try to ssh in, I have no clue how to have it proceed. Is it an if statement? Here's the telnet failed message: telnet: Unable to connect to remote host: Connection refused
I'm setting up a computer with xUbuntu installed and wan't to run it as a PPtP VPN server.
I'm using a mobile broadband for internet connection, with DynDNS wich updates the host with public IP-address.
I've managed to set up the connections and installed the needed packages. The problem appears when I connect to the VPN server through another computer;
When I get connected to the VPN server the remote computer recieves an IP-address from the server (xUbuntu) wich is great! But the server changes prefered network, from the mobile broadband to the wired network wich results in the remote computer losing it's connection to the server.
I have a box running Fedora 14 upstairs and I've been trying to get it to run VNC server, unsuccessfully. I've RTFM, and followed the instructions step-by-step, but it still won't run. I'm getting no error messages. But when I try to connect from either a Window or Mac client, it either get a timeout or connection refused. I've read and tried all the troubleshooting; been working on this for about 12 hours now. Is there something major that I could be overlooking?
View 14 Replies View RelatedI am using redhat on server and open suse on client. When I want to ssh from my server machine the following error occur "connection refuse". I execute the following command on clien machine "/etc/init.d/sshd start". It shows the following error just after command execution "sshd re-exec requires execution with an absolute path".
View 1 Replies View Related