Ubuntu Networking :: How To Stop Network Manager From Auto-reconnecting
Apr 11, 2011
I am running openVPN to secure my wireless network traffic right now. Everything works great except every once in a while, my Internet connection will drop out for about a minute or so. Ubuntu very nicely tries to reconnect, and most of the time successfully does. The issue is that if I don't catch it every time this happens, I am now running without my VPN.
I want to know if there is any way to DISABLE auto-reconnect to a wireless network if connection is lost or signal fades.
Im running ubuntu 10.10 by the way
View 3 Replies
ADVERTISEMENT
Jul 1, 2010
I recently fixed an annoying problem and I thought it would be nice to share my solution here. The problem was that after a cycle of suspend/resume, Network Manager would only auto-connect to the same network as it was previously connected to. So, for example, if I suspended my laptop at home, and then I went to school and resumed it, it would try to connect to the home network, and then just give up. It would not connect to the school network unless I explicitly told it to.irst, I'll describe the fix. If you're having this problem, you can this. Copy the following:
Code:
#!/bin/sh
case "$1" in
[code]....
View 5 Replies
View Related
Jul 10, 2011
I would like to stop network manager from starting up on boot. I have tried moving
Code:
/etc/init.d/network-manager stop
to rc.local and it did nothing but boot me into the CLI
I have also tried to put
Code:
sudo service network-manager stop and that did nothing also.
After I get network manager to stop on boot up. How do I make it so it will not auto connect to networks? My computer keeps on joining a different network on boot up. And I don't like this as some times I go to my banks website and I am on there network with out realizing it (because of the auto connect) Is there a way to stop this also?
View 6 Replies
View Related
Jun 23, 2009
I got a little problem with network manager. I got two connections in it, with two different DNS-Servers, because the one of my provider is very slow I surf with opendns, but sometimes that slows down too, so I want to change if necessary. Both connections got the same fixed IP.That worked all fine, until I got my new router (it's a Netgear WGU 624). It's connected by cable and I configured it like the old one. But for some reason instead of connecting to the manually configured connections, my fedora 10 creates a new one "auto eth 0" with a dynamic IP. So every time I boot or switch on from standby my PC connects with this one and I have to manually set it to the right connection. There's no chance to edit or delete it cause those two buttons are grey and won't work. I also tried restarting network manager manually and I also tried starting it with su as root.
View 14 Replies
View Related
May 3, 2010
I'm running Kubuntu 10.4. My problem is that Network Manager keeps defaulting back to Auto eth0. I have created a new wired connection and set my manual addresses. I have ticked the 'connect automatically' button. Every time I reboot or wake up it reverts back to Auto eth0.I did have wicd installed but this was not reconnecting after wake up (said it was connected but I couldn't ping etc), this is a pain also.
View 9 Replies
View Related
Apr 13, 2011
Within the last couple of days or so, my wireless has been on the fritz. It keeps disconnecting and reconnecting every minute or so, which is annoying to say the least. The information relating to my wireless network is:
Laptop model: Toshiba Satellite L350
Wireless interface: Atheros AR5001 Wireless Network Adapter
Interface:
[code]...
View 3 Replies
View Related
Sep 13, 2010
I typically have several terminal windows each of which is connected via ssh to a remote server. In each window I work using the gnu screen program, to ensure persistence of the interactive processes in case of a disconnection.
Currently, whenever the ssh connection drops (such as when I put my client computer to sleep overnight) I have to manually and tediously restart the ssh session inside each window, and then in each window tediously resume the specific screen session (e.g. "screen -r 3453" in one window, "screen -r 3462" in the other etc.)
Is there an elegant way to automate this? Specifically:
reconnect the ssh session if it drops, as soon as an Internet connection is detected run the specific screen instance for the terminal window as soon as ssh reconnects
View 2 Replies
View Related
Aug 12, 2011
I'm putting a opensuse 11.4 64 bit KDE install on an HP -G62 laptop.
I also use an NFS network.
I want to use a wireless network.
The problem is that network manager keeps insisting on asking kwallet for permission to start up the network. As a consequence boot hangs because the nfs network can't find the files in /etc/fstab because the network can't start because you can't see kwallet until it finishes booting.
I have options set in networkmanager to store the password in connection secrets in secure storage, and it insists on asking kwallet!
I don't want to get rid of kwallet because it's very useful otherwise - just not at boot time?
How do I modify the behaviour shown here?
View 1 Replies
View Related
May 25, 2010
I have Debian Squeeze AMD64 bit release. It finds my wired ethernet connection and ues itfine, although nothing shows up in the top right corner under the networking icon.
When I plug my mobile phone in (HTC S620) it always uses this as the main internet connection and then even if disconnected wont use my wired connection until I reboot.
Is there a way to stop it doing this or at least have my wired connction as an option so I can just click to reconnect to my ethernet connection?
View 2 Replies
View Related
May 6, 2010
I'm trying to use network-manager in sid and it's incredibly frustrating because every 2 minutes or so it seems to scan for wireless access points, during which time my SSH connections completely hang and screw up. Pings start dropping packets as well. By doing an "iwlist scan" I can reproduce the behavior. Has anyone else dealt with this? I haven't been using network-manager, but I am currently due to mobility and needed VPN functionality... WICD with no network-manager works better but there's no gui-based VPN support. I've got an Atheros wireless device and I've read that supposedly it should be doing background scanning since kernel 2.6.32, but I haven't seen anything like that, and I'm on 2.6.32-5-amd64 currently, 2.6.32-3-amd64 behaves the same too.
View 4 Replies
View Related
Mar 18, 2011
I would like to disable auto loading of network manager/wpa supplicant in my FC13 system. I am not interested in just stopping the service (/etc/init.d/NetworkManager stop) from user lever. Is there any kernel configuration which can serve the purpose. If there is a way to stop notifying user level about new network interface, please let me know.
View 3 Replies
View Related
May 24, 2010
SPM has just two options 1. Direct connection(no proxy) to internet and 2.manual proxybut my firefox cannot connect to internet with no proxy, It can connect to internet only on auto-detect proxy settings option.Right now my SPM is not working. I can ping the SPM server from my console but apt-get is not working
View 3 Replies
View Related
Aug 19, 2010
If I made a distro from scratch it would have been Lubuntu, cept I'm sure my theming would have been horrible. Now Ive installed on a couple of my Laptops, and even had a few friends convert, and for the most part everything is hunkus doris, cept one small issue thats keeping me from slapping it on my trusty laptop. I'm lost as to what the problem could be. Ive tried just about all I can think of, but I use sprint mobile broadband to connect to the net and then use Network Manager to share this connection with the laptops and Palmtops around the house. I can get my sprint modem to connect thats not a big problem the problem is now I cannot get the Auto Eth0 to connect to send out as a share. It just refuses to connect. Now this is not a Lubuntu problem at all Im sure its somehow a Lxde problem, as Mint Lxde, PeppermintOS, and so on do the same thing, refusing to connect Auto Eth0 while Sprint is connected. Any Gnome based distro this works flawless, as does Xfce distros, so Im sure this is somehow something within Lxde. Im sure its down to just "missing" a file or some stupid overlooked thing.
View 3 Replies
View Related
Jun 12, 2010
I m using Ubuntu since 8.10 Then i switched to 9.04. When i tried 9.10 I was not able to connect with my Huawei EC325 modem which was available as an auto CDMA connection in the nepwork manager applet.I posted this in ubuntu forums. This could not get my Huawei USB dongle get connected. So I reverted back to 9.04 from 9.10. recently i tried Lucid. i was dissapointed with it. It seems Auto Cdma connection option under mobile broadband connection is been removed from 9.10. Jaunty updates will be available untill October 2010. So after that for a USB mobile user like me It will be difficult for me to get my 9.04 updated. Ubuntu 9.04 will be outdated. cannot you suggest some methods to solve the problem or shall i stick to jaunty jacklope.
View 1 Replies
View Related
Mar 16, 2010
Since OpenSuse 11.2 doesn't reconnect samba shares upon a resume from suspend, I wrote a small, ugly script to do so. It's placed in /etc/pm/sleep.d/66samba-remount
#!/bin/bash
case $1 in
hibernate)
echo "Hey guy, we are going to suspend to disk!"
/etc/init.d/smbfs stop ;;
suspend)
/etc/init.d/smbfs stop ;;
thaw)
echo "oh, suspend to disk is over, we are resuming..."
sleep 15
/etc/init.d/smbfs restart ;;
resume)
sleep 15
/etc/init.d/smbfs restart ;;
*) echo "somebody is calling me totally wrong." ;;
esac
and made it executable
(as root)
chmod +x /etc/pm/sleep.d/66samba-remount
The 15 seconds sleep time is useful to me to postpone the remount after WiFi is back online. Perhaps there are way more elegant ways to do so (check for x times if WiFi is on, for example), but I'm no good at bash, and this serves me well. How do I file a wishlist for 11.3? If someone puts a samba share in fstab, I'd assume he wants it connected mostly everytime (at startup for sure... so why not over a standby?) I hope 11.3 just reconnects in-fstab samba shares in a polished way, out of the box.
View 1 Replies
View Related
Jan 29, 2011
I have a Broadcom Corporation NetXtreme BCM5721 network card on my server at work.Everything works fine for a few weeks, then randomly the network connection on the server will stop working. After it stops working, I will try to reconnect with the network manager, it shows a wired connection available, it shows the "connection in progress"animation, then the "connection disabled" icon.
I uninstalled the network manager and used manual configuration, but do you think the network manager was the issue? I can't have the server disconnecting randomly every few weeks with no way to know what the real problem is. Was there an issue with the network manager with 10.04?
View 4 Replies
View Related
May 1, 2011
I want to know any command which is equal to disconnecting and reconnecting lan cable. actually sometimes my router takes some time to connect to internet and when this happens my desktop shows network disconnected. but when router is connected system does no detect it and i have to manually disconnect and reconnect the cable which is not convenient.
I have debian 6.0.1 (squeeze) with gnome 2.30.2
And i have already tried following commands:
View 10 Replies
View Related
Oct 26, 2010
I installed 10.10 for some days ago, networking was working smooth back then. I use a ethernet cable to connect to the internet.But yesterday when I installed 10.10 on my brothers laptop(he connects through wireless), I began to get these disconnects and reconnects.They just seem to happen random.
View 2 Replies
View Related
Jan 24, 2011
I am a Windows refugee who discovered Ubuntu as a way to save my files from my virus-ravaged computer. Had no installation discs for Windows, so when I had to wipe my hard drive and start over, I decided to give Ubuntu a try. I've had mixed success, but that's another post...
Right now, the problem is that I installed 10.10 two weeks ago and was able to connect to the Internet with no problems - until yesterday. Suddenly, our wireless network (the only one in the vicinity) does not come up as available in Network Manager. In fact, the entire wireless option disappeared. I know there are many posts and threads on here about this, but weeding through them trying to find an answer is more frustrating than actually dealing with the problem. I know the router works because I can post on this forum from the Macbook. I really like Ubuntu and would like to keep using it, but not being able to connect to the Internet now on top of the other issues I've had is making me doubt I want to continue down this Linux road.
P.S. When I attempted an analysis through System Testing, it said something about there being no proprietary drivers?
View 2 Replies
View Related
Jun 14, 2010
I have used ubuntu in the past but had a lot of hardware issues with it and unfortunately moved back to windows (( BUT i have tried Ubuntu again and all seems to work great except wifi My wifi connection is sort of working because when i run SUDO IWLIST SCAN it does pull up all available networks. But in the network manager icon on the panel i left click but i see no networks and can't connect to anything. I WOULD LOVE TO keep Ubuntu and use it permanently but I must get wifi working or else this won't be possible.
View 4 Replies
View Related
Feb 10, 2011
I am access my linux box remotely using putty. I ran some build process on the remote machine. I lost my connection and now I had to re login using putty. I dont know if my process has finished or not. How will I check that.
View 2 Replies
View Related
Jul 9, 2010
Been trying to deal with this one for some time, and still not sure it's more or an issue on the Samba or Win 7 side.
Running Ubuntu 10.04 with Samba 3.4.7, using Windows clients from 2000 on up to access shares.
2000 and XP have no trouble both connecting initially to shares, but upon reboot the shares are disconnected and do not automatically reconnect unless one of them is double-clicked on. Passwords and mappings are saved such that Windows tries to reconnect upon restart. When manually reconnected in this way, shares remain open as they should. This isn't a big issue, but it would be preferable to have these shares reconnect so that links and shortcuts across the LAN work right from bootup.
The bigger issue is with Vista/Windows 7 - When shares are set up with appropriate passwords and such on the clients, they work as expected, until the client is rebooted. After signing into windows 2 things are observable:
- Black screen for 2-5 minutes before desktop appears
- error message appears when you try to double-click on a mapped share (even with a saved password) that the connection cannot be restored.
If you go into credentials manager and delete the saved password for the share(s) on the samba server, you are prompted for the password when you try to open any of the shares - reenter it and you're then fine until the next reboot.
There must be some issue with the persistence of the saved password, but not sure if this a Windows-side issue or not. Read some other info on this, and had to make the following changes earlier to even get Win 7 clients to connect to samba at all:
[URL]
It appears that when Win 7 starts up, it simply can't connect using the saved password, and the desktop doesn't come up until the reconnecting action(s) time out (if you disconnect your win 7 machine from the network the delay is not present).
It's not a game-breaker, but really annoying when rebooting having the delay and reentering the network share password(s).
View 9 Replies
View Related
Jan 10, 2011
I've just loaded the new Hamachi2 Linux beta with Haguichi for a GUI. Everything installed & connects OK, but the connection at the hub is dropping & reconnecting every minute or so. I tried adding a line to the sshd_config file to keep it alaive but it didn't make a difference.
View 3 Replies
View Related
Feb 10, 2011
I am using ubuntu 9.10. in my area there are frequent power outage. So my wifi get disonnected as the router stops. And it asks for security code. So when power comes the router starts but i have to manually write the security code and connect to wifi again. how i can make the computer to auto connect to wifi after power comes.
View 3 Replies
View Related
Jul 18, 2010
This should not be this difficult. I have a plain install of Ubuntu 10.04 64 bit with a wired network card. It picks up a private IP address from my router. It has an app called NetworkManager Applet 0.8 in the notification area of the panel. If I right click on this app and select "Disconnect" it does. ifconfig shows that the IP address is gone. I can then right click on the app again and "Auto eht0 and I am connected again and ifconfig shows the IP address restored. So far, so good. I was testing a crossover cable to see how fast I could transfer files to/from my server - both machines have gigabit cards but my switch is only 100 Mb.
I unplugged the PC from the router, hooked up the crossover cable to the server and found that I had no connectivity - the IP address was gone. Not wanting to mess with hard configuring IP addresses for the moment I connected the PC back to the router. When I unplugged the cable the app showed the networking disconnected icon. I tried right clicking on the app and unchecking [ ] Enable Networking then rechecking it. This works on my netbook running Ubuntu 9.04. No luck on 10.04 (and I had not tried the Auto eht0 as described above - did not discover that until later). So then I tried to fix it from the command line.
ken@taylor12:~$ sudo /etc/init.d/networking start
Rather than invoking init scripts through /etc/init.d, use the service(8)
utility, e.g. service networking start
Since the script you are attempting to invoke has been converted to an Upstart job, you may also use the start(8) utility, e.g.
start networking
networking stop/waiting.
So I then tried
ken@taylor12:~$ sudo service networking start
networking stop/waiting
but still no connectivity. A reboot got things back in order.
Then I did a little more testing.
ken@taylor12:~$ sudo /etc/init.d/networking stop
* Deconfiguring network interfaces...
Ignoring unknown interface eth0=eth0.
and I am still connected.
Editing Connections within the NetworkManager Applet shows "Auto eth0 - last used never" even though I have used it. [Edit] Auto eth0 via the app appears to show information about my wired NIC.
ifconfig shows eht0 as active
ken@taylor12:~$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:25:64:e8:18:2c
inet addr:192.168.0.112 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::225:64ff:fee8:182c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2234 errors:0 dropped:0 overruns:0 frame:0
TX packets:2407 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
bytes:1824427 (1.8 MB) TX bytes:404086 (404.0 KB)
Interrupt:17
View 2 Replies
View Related
Feb 18, 2010
I have the problem with my notebook, that, after I used it at work, the network-manager always tries to autoconnect after boot. He has no cable network and so I get the message "not connected" after a while.how to tell the network-manager, not to autoconnect each time?
View 4 Replies
View Related
Jul 10, 2010
I recently put Linux on a Thinkpad T40 I got. The wireless card works out of the box--I can see nearby networks. However, I can't connect to mine. network-manager would try (spin spin spin), fail, ask for the password, and then go back to the beginning and repeat indefinitely. This happened to me on a different computer, and on that one all I had to do was use wicd instead of network-manager. So I installed wicd, but it's not working either--it hangs at "Obtaining IP address".
I've found many, many threads with people who had the same problem, but none of their fixed worked for me.
I also tried to get wifi going manually, using this guide, but that didn't work.
View 3 Replies
View Related
May 2, 2010
Upgraded To Ubuntu 10.04 The Other Day. And when I first installed it everything worked great except for my sound card which I fixed. But there was no problem with connecting to my Router via an Ethernet cable. Then I updated the video card drivers, restarted my PC and it wouldn't connect. It would try over around 1-2 mins then tell me its disconnected. No green light activity on the router / network card either.
I've reinstalled fresh copies of Ubuntu a couple of times now, Hoping to get the default settings back. But nothing has worked since.
I looked around the net and found quite a few people had this problem on previous versions of Ubuntu but it would seem most of there fixes were for there Version, so it hasn't helped me.
Heres some info:
ifconfig:
I've tried all the various things from dhclient to ifup/ifdown etc etc.
View 9 Replies
View Related
Jan 28, 2011
I've been trying to get and old PCI wireless card to work on Ubuntu 10.04. The card is a Zonet 1602. It was not recognized automatically.
I have been able to get it to work using ndiswrapper except that when the computer is started it does not automatically connect to the network. I can click on the network icon and select my network from a list and it will connect, including properly authenticating the network key.
I have worked through a lot of information on the web but much of it seems to apply to earlier versions of Ubuntu and some if it does not match what I'm seeing in 10.04.
There is a built in Ethernet controller on the mother board but I have disabled it in the BIOS.
View 3 Replies
View Related
Jul 21, 2011
I am using BSNL broadband ISP and I am able to get network on windows os but not on my ubuntu.( I have a dual boot). I see Auto eth0 connected from the notification but when i am pinging [URL]... it says unknown host.
View 9 Replies
View Related
