I was able to connect normally with winXP then installed ubuntu and now am unable to connect. I have a TW-EA510 ADSL modem router connected to ubuntu computer. How do i make it work
View 9 RepliesI just installed Ubuntu 10.04 on my mac G4 (PPC) and it does not connect to wireless with my wireless card (drivers maybe) I am a complete newbie with any linux operating system (I've tried SLAX but never kept with it) So is there anyway i can use my laptop with Windows XP to cennect to the wireless on my G4 using an Ethernet cord?
View 2 Replies View RelatedI installed karmic to a flash drive, and grub overwrote my winxp mbr. On boot it has an error that grub can't load and then shows the grub rescue prompt. I've tried fixboot and fixmbr and bootcfg /rebuild from the repair console with no luck. Grub loads if I leave the flash drive in, but it takes a long time.
The boot_info script provided this data:
Code:
Boot Info Summary:
=> Grub 1.97 is installed in the MBR of /dev/sda and looks for
(UUID=18f3e5ee-7ef2-4158-8b84-853630827dea)/boot/grub.
=> No known boot loader is installed in the MBR of /dev/sdb
=> Syslinux is installed in the MBR of /dev/sdc .....
I installed Ubuntu 10.04 on a USB hard drive after booting the desktop installer ISO on a USB flash stick. My laptop already had Windows XP installed on the internal hard drive and i did not load Ubuntu onto that disk. I can no longer boot the Windows OS. My laptop shows a grub rescue prompt with "no such device" error. I can mount the internal hard disk ("system drive") and see all the Windows files from within the Ubuntu desktop installer. Is there a way to restore my Windows system drive to boot or do I need to reinstall?
View 3 Replies View RelatedWhen I load into winXP I can see the files for winXP and win7. When I load into ubuntu I can only see winXP. i did a sudo update-grub and got the windows loader, which then shows me winXP and ubuntu. what i would love is one boot page that has listed winXP, win7, and ubuntu. FWIW this is an acer netbook, winXP is on D:/ and win7 is on F:/, i used the windows installer wubi for ubuntu 10.10.
View 9 Replies View RelatedYesterday I reinstalled my ubuntu 11.04 and now I cant get samba to work. I allso installed Firestarter to get internet connection to my media center pc. In firestarter I have unchecked in the "advanced options" "block broadcast from external network".In my media center pc when I go network connection and view workgroup computer, I cant see my computer at all. If I try to ping my computer then everything is ok.
View 1 Replies View RelatedI just downloaded ubuntu 11.04 and installed it and everything off of a cd and now I cant connect to internet wirelessly! My WiFi button on my laptop is orange and I press it and it doesn't go blue like it normally did when I had windows vista. I just updated my wireless driver off of ubuntu and restarted and nothing happened! its still not connecting me to the internet, I only have access through the ethernet I am using. I cant go ethernet, this is only temporary and I really want ubuntu, I really need it, but its not letting me go wireless. My wireless driver is this: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 02)
View 2 Replies View RelatedEven though having already spent many hours trying to connect to the internet from Ubuntu, I still haven't done it succesfully. What I've done so far:
Code:
nuno@Houdini:~$ ndiswrapper -l
WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release.
WARNING: All config files need .conf: /etc/modprobe.d/ndiswrapper, it will be ignored in a future release.
bcmwl5 : driver installed
device (14E4:4318) present (alternate driver: ssb)
On the bar at the top, under 'Wireless Networks' it reads: "disconnected".
I just installed 10.04 LTS on my husband's Dell laptop but don't know how to get my wifi to work. I did some searching here in the forums and found a bunch of posts, but all are from 2008 or earlier meaning that they are probably not for my version of Ubuntu - feel free to tell me that the steps are the same.
Anyway, I did a 'lspci' in Terminal and the important lines that appeared are:
03.00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base0TX (rev 02)
0c.00.0 Network Controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01)
So my system does recognized the wireless card, I just don't know how to get Ubuntu to find available networks. I tried adding in our network as a 'hidden' network - which it isn't and that didn't work, so I'm up for any suggestions in how to get the computer to connect to the wifi network?
I have managed to compile and install the driver for my linksys AE1000 adapter. I can scan and see my network (and several others) but can't seem to connect. I have read a few threads looking for clues but I can't seem to figure it out. My kernel is 2.6.35-24-generic and I am using the latest rt3572 driver (v2.5.0.0). Here are a couple of steps that I have taken:
1) The usb driver does work properly and connect on a Windows machine.
2) Temporarily removed security from my router (uses WPA2). Still can't connect.
3) Tried compiling and installing the previous version of the driver (2.4.0.2)
On my Ubuntu installed xl2tpd. Connected from Win7 without any problems. But I cannot connect from iPhone. Where I can get pre-shared key? Is it differ from password?
View 8 Replies View RelatedI just installed Ubuntu Remix 10.04 on my wifes MSI U100 netbook. I did a dual boot just in case she had to get into Windows for something. I let the install automatically partion (did the side by side option). Anyway, Ubuntu works fine and imported all her documents and stuff. Problem is Windows XP won't boot. The first time I tried to boot Windows XP I got a message saying the hardware had changed and I had to select safe mode, normal boot, last known good, etc... I booted normally. I got the splash screen followed by a quick flash of BSOD and a reboot. I does this no matter how I try to boot Windows (safe, command prompt, etc). Anyone have any idea what the problem is?
View 3 Replies View Relatedxxxxxx:/etc/samba$ uname -aLinux xxxxxx 2.6.38-8-generic #42-Ubuntu SMP Mon Apr 11 03:31:50 UTC 2011 i686 i686 i386 GNU/LinuxI have a printer shared off of Windows XP. I have always been able to print to this from Ubuntu by adding a network printer through the "Windows Printer via Samba" gui.Now, in Natty, I can set up the printer no problem but all jobs fail. In the printer properties gui I can see this text briefly: "Processing - unable to connect to cifs host".The errors in /var/log/cups/error_log are:
E [28/May/2011:14:32:31 -0700] [Job 15] Tree connect failed (NT_STATUS_BAD_NETWORK_NAME)
E [28/May/2011:14:32:31 -0700] [Job 15] Tree connect failed (NT_STATUS_BAD_NETWORK_NAME)
E [28/May/2011:14:32:31 -0700] [Job 15] Tree connect failed (NT_STATUS_BAD_NETWORK_NAME)
[code]....
Ever since my upgrade to 10.04 I no longer have Samba shares to my WinXP system(s).I have searched the forums high and low and for the life of me cant figure out what I am doing wrong.I am not able to see my XP system from Ubuntu, nor see my Ubuntu system from XP.Attached here is a copy of my smb.conf.
View 9 Replies View RelatedI'm setting up a network for a school. The network has 11 client computers (windows xp) and a server (fedora 10) All I need to do is have a share for all the children to use. (this I did by adding each client to the workgroup specified on samba then I just map the drive). The issue turns out to be that I have over 300 users. The users don't always use the same computer therefore I need the users to be registered on all 11 clients. How can I do this? I have been searching and I've not gotten anywhere. How can I add the computers to a domain instead of a workgroup? What can I use?
View 1 Replies View RelatedI am running VMware workstation on a Linux host and WinXP guest using NAT. I have shared a folder on WinXP, and I am able to mount it on the linux host with:
mount -t smbfs -o username=Administrator,password=mypasswd //192.168.100.129/Shared /mnt/tmp
This works fine. However, I want to mount the same folder from a different linux machine (not the host).
I added port forwarding in /etc/vmware/vmnet8/nat/nat.conf:
[incomingtcp]
#445 = 192.168.100.129:445
If I run:
mount -t smbfs -o username=Administrator,password=mypasswd //external_ip_number/Shared /mnt/tmp
I am getting:
mount error 112 = Host is down
Refer to the mount.cifs(8) manual page (e.g.man mount.cifs)
It doesn't work even if I try the above command from the linux host itself. It only works if I use the internal IP number. I suspect vmware is not forwarding port 445 but I am not sure how to verify it. I am not running smbd on the linux host, in case that make any difference. I didn't think that was required because the server is really on the WinXP and the linux is just a client.
I want to access RHEL5 by remote desktop from windows XP.
View 1 Replies View RelatedMy home linux box is behind a Linksys WRT110 router. I have enabled the Remote Desktop from System-->Preferences-->Remote Desktop. I then run TightVNC from my WinXP box. As I wish to run a secure connection, my first obstacle comes from PuTTY.
In PuTTY, my settings are as follows:
Host Name(or IP address) Port
xxx.xxx.xxx.xxx 22
SSH-->Tunnels:
[code]....
I recieve "Network error: Connection refused" I have gleened all of this information from other boards and tutorials. I know there is something critical that I am missing.
My office is on migrating to UNIX system. I am configuring Centos as our server including some program will be running on it. But one of the problem is we use foxpro for operating some program on server directly. I can run that program on Centos using DOSBox. My question is how can i run that program on winxp client that connected to network through samba to that program on server? so my plan is just give the shortcut and link it to server. I have tried to open it but not work.
View 1 Replies View RelatedI have a network of 2 WinXP machines and one linux box. I have fiddled around with the settings as you do when learning. The network is working. The network neighbourhood on the WinXP machines recognise the linux box and vice versa, (the linux Places|Network recognises the 2 WinXP). I can Ping the linux box using its hostname from a WinXp. But I cannot do the reverse. I get an 'unknown host' response. I can ping the linux to itself using its hostname.
View 7 Replies View RelatedI just installed ubuntu server, and I need to use a usb wifi thingy for it, but it refuses to connect. The computer recognizes the wifi, and I can even do "sudo iwlist scan" and see my wifi network, but I can't figure out how to connect.
View 1 Replies View RelatedOk so I have recently purchased my VPS and I have installed the wonderful "Ubuntu 10.04 32bit". I have installed VNC fine and I can connect to the Remote Desktop with a GUI.Im looking to run "RsBot" but im unsure on how to run Java. I am really stuck and I was wondering how I can install java as when I try and run the setup it just open the folder up..currently installing OpenJDK Java 6 Runtime, ill update you when its done.
View 3 Replies View RelatedI installed teamviewer and immediately skype went offline. Upon logging in to skype I get the following error:
"skype p2p connect failed"
So I rebooted pc, router, performed the command: "rm -rf ~/.Skype" to no avail. Next I removed teamviewer and tried everything again & still the message persists. Skype was set to not use port 80 already, but if it won't log on then I can't get to full the options menu.
I keep getting this error trying to connect to newly installed postgres server on Amazon EC2 running Ubuntu Maverick Meerkat....
Could not connect to server: Operation timed out Is the server running on host "....ap-southeast-1.compute.amazonaws.com" and accepting TCP/IP connections on port 5432?
I've updated config files, as follows...
pg_hba.conf
added
host all all 124.168.242.0/24 trust
where 124.168.242.0 is the IP range of my ISP
postgresql.conf
listen_addresses = '*'
port = 5432
I am attempting to connect with pgAdmin 3 client. I don't think the problem is the client.
I have just installed Mandrake Linux and everything seems OK apart from the fact that I can't connect to the internet. I presume it's because I have not got the relevant driver (or have not configured it if it's there)y machine was previously running Windows and all the disks I have are for Windows.I have looked in my manual and it says I have a K8NBP GRAND (I think that's the motherboard, you'll see that I don't really know a lot!!) The manual also says Gigabit Ethernet LAN : NVIDIA Gigabit MAC + VITESSE Gigabit PHY - Supports 10/100/1000Base- T Ethernet/Fast Ethernet/Gigabit Ethernet.When I was running Windows I just had a network cable running out of the back of the PC connected to one of the LAN sockets on my routerI am currently having to use my wife's laptop (which runs on yet another OS but at least it connects to the internet or I'd be really stuffed).
View 5 Replies View RelatedI have installed the madwifi drivers and I am able to put the wireless device into monitor mode using airmon, so that tells me that the driver is working and the device can be picked up...
But I still can't connect using Wicd and I really don't know what to do next
My wireless (Toshiba laptop, 10.04 64 bit) is just hanging when trying to connect. It was working fine but now nothing. My Wireless antennae is on and my other laptop can connect with no problems. I have restarted the router and the laptop twice.
View 1 Replies View RelatedI am unable to connect to wireless network in ubuntu 10.10.i have noticed that the iwlagn driver isnt been used by anything.
View 9 Replies View Relatedin linux world and have recently downloaded and installed ubuntu desktop 10.10i cannot connect to both wired and wireless ethernet on my laptopit tries to connect but fails in 30 seconds , it says"disconnected" while i am able to connect to the same in windows i have broadcom 4315 and i have tried both fwcutter and ndiswrapper but the problem persiststhe device id is 14e4:4315
View 9 Replies View RelatedI am trying to setup a dhcp server for my internal network. I have two NICs, a modem, and a wireless router. I have my server connected directly to my modem which is providing me with Internet access on eth1 and is working fine. I have dhcp and dns setup on eth0 which is connected to my router. The router shows that it is connected to the Internet but when the router gives a client computer an IP address, the client is unable to connect to the Internet but can connect to the router. I will post my configuration files below with my current configuration.
[Code]....