Ubuntu Networking :: Samsung N130 Netbook & RTL8192E & Wireless - Access The Internet?
Nov 30, 2010
Has anybody been successful in getting a N130 with a RTL8192E wireless chip to access the internet? I�ve tried practically every suggestion quoted on this message board �downloading drivers, from Samsung and Realtek which won�t open also linux versions with the same result, trying the Ubuntu compilation of Wine etc, etc. Am about to give up, which is a pity, because the Netbook version Ubuntu is very user friendly.
View 3 Replies
ADVERTISEMENT
Nov 7, 2010
I've got UNE 10.10 installed on a Samsung N150 that uses the RTL8192E for wireless. When the wireless works then it generally works okay, but I'm having problems with reboots and long-running connections. This is different to the mass of posts (mainly from 2009) about the card not working at all, so I started a new thread.Basically, 90%+ of cold boots result in a successful wireless connection, with Network Manager remembering my WPA password.
When the wireless is up then it never obviously drops out, but I've got an app with a long-running connection that seems to disconnect itself occasionally. Looking at Wireshark then it appears that there are a number of retransmits, and a big batch just before it disconnects (which implies that the app is dropping its connection because it thinks the other end disappeared). Running the app on another machine with a different card but through the same release of Ubuntu and the app and the same router doesn't result in retries or drop-outs.On the times when a cold boot doesn't successfully reconnect then it asks for the WPA password, then continues trying, then asks for the WPA password again, then continues trying, then asks...and so on until I rmmod and modprobe the driver.
I originally had problems with the machine refusing to restore after a hibernate/suspend, but this was solved by a tip to rmmod the driver on hibernate/suspend and modprobe it on restore.The wireless will now work okay on some restores, but is more likely to repeat the behaviour described above for the failed cold boot.
Code:
$ lspci -nn
...
05:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8192E Wireless LAN Controller [10ec:8192] (rev 01)[code]....
Attached is a file with some snippets from dmesg around the time of the wireless failure, and the log of what it does after a remove and re-add for comparison of the "correct" messages.
View 3 Replies
View Related
Apr 2, 2010
I have a Samsung N130 with a Realtek 8192 wifi card (possibly 8192e, I'm not sure) and I am trying to run Fedora 12 on it. I used to run Ubuntu until trying their latest beta and realizing it's not very good, so I looked for something else. Ubuntu was at least easy to get the wifi working with just a few quick commands that were written out, word for word, in order, on the Ubuntu forums. I tried openSUSE on here and it didn't have wifi working out of the box either but people on their forums refused to give me actual instructions and just kept bumping me from thread to thread with people giving vague advice or else just telling me I was looking in the wrong place. I'm hoping that someone can give me clear and detailed instructions on how to get this wifi card working. Keep in mind that I am coming from Ubuntu and so I'm not super comfortable in CLI, if I need to do some CL stuff I will need clear and detailed instructions on how to do that.
View 4 Replies
View Related
Apr 23, 2011
I need to connect to wireless internet in ubuntu netbook 10.10, but it says 'device not ready (firmware missing).
View 2 Replies
View Related
Aug 4, 2010
I installed lucid netbook edition on my friends netbook and I am unable to connect to their wireless. The netbook is dual booting with xp and while in xp it is able to connect but once i boot into lucid it is unable to.
View 2 Replies
View Related
Sep 23, 2010
1. HP Mini 110-3000
2. 02:00.0 Network controller: RaLink RT3090 Wireless 802.11n 1T/1R PCIe
3. wlan0
4. cant find...
5. nothing come out...
6. *-network DISABLED
7. wlan0
8. Description:Ubuntu 10.04.1 LTS
9. 2.6.32-24-generic i686
10. * Reconfiguring network interfaces...
I cant see any access point from my router...
View 1 Replies
View Related
Sep 17, 2010
I cant connect to the internet with my wireless( or my lan for that matter, but i mainly want to use my wireless). I am going to follow the ticket provided by one of the sticky threads [URL]
1.Machine Brand and Model
Actually i am using a computer i built myself using following components
AMD Phenom II x4 965 CPU
ASRock 890FX Mobo
[Code]....
View 4 Replies
View Related
Jun 28, 2011
am currently using Windows 7 across my networked PCs at home.
I've just received my new Samsung N250 Plus Netbook which comes with Windows 7 Starter (yuk). I read a post on Ebuyer from someone who has installed ubuntu on his N250 so thought I'd give it a go tonight.
My main concern is whether my wi-fi card (Broadcom 802.11n according to windows) will work when I remove windows and install ubuntu. I intend to use the netbook for internet use only while working abroad.
Is it possible to test it works by running ubuntu from my USB stick first (without removing windows 7)?
View 6 Replies
View Related
Feb 10, 2010
Running Ubuntu 9.10 Ive just got my wireless connection working after first having got the wired eth0 connection working.
With the wired connection I could SSH into my server through my firewall/router (via a forward). I can run up VNC, from there firefox, browse the web - all is well.
I have now setup the wireless connection, using a static IP, and I can likewise SSH into my server. I can run up VNC. I can ping my router. I can log onto it via VNC. I can browse to my router. But I cant browse the internet.
But I cant ping google.com. The reason is there is no host lookup service. Nslookup eventually says no servers could be reached.
So specifically, if I ping www.google.com Im told "unknown host". If I do an NSlookup on it I get timeout, no servers could be reached. However if I ping 66.102.11.104 I get responses.
I see no relevant entries in my firewall log.
Unfortunately I cant traceroute because the package isnt found - and of course I cant install it because I have no internet !
Strangely (to me at least !) if I then tunnel through SSH and browse the web, I have no problems. It works ? I know I am browsing through my SSH tunnel because whatsmyip gives the IP of my router at home, not where Ive SSHd in from. I can surf just fine.
why I cant do host lookups any more (and this did work with my wired connection, but whether its related to my change to wireless, or static IPs or both I cant be sure - it certainly appeared to happen at the same time). And, more to the point, what I need to look for/do to rectify it ?
As a bonus Id be interested in why I can SSH and browse via tunnelling but not direct from my server (via VNC). Just for interests sake !
if config reports :
wlan0 Link encap:Ethernet HWaddr 00:90:4b:27:ae:17
inet addr:192.168.1.69 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::290:4bff:fe27:ae17/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[Code]....
View 1 Replies
View Related
Apr 18, 2010
I have a dual-boot desktop with Windows 7 and Ubuntu.Problem: Linux does not recognize my D-Link DWA-131 Wireless N USB Adapter. So, I can't access my wireless router or the internet.D-Link has a Linux driver for the DWA-131 posted on their website URL...that includes a readme file with long, strange, convoluted instructions on how to install the driver.
View 9 Replies
View Related
Dec 6, 2010
I had been happily using a wireless connection for about two weeks. The connection then went down for a few days. Since it came back up, I can connect to the network, but cannot access the internet. Other users of the network can both connect to the network, and access the internet, though people have experienced the same problem as me the last time the network went down (they could connect to the network but not access the internet). I have tried deleting and re-starting the connection, to no avail. I have looked around the forums, but haven't found anything that can help: do any of you have any suggestions? I am malarial and at the end of tether.It is not a problem with Ipv6, which is set to ignore, as it was in the past when the connection workedI am running Ubuntu 10.10 on an X61 Thinkpad. Below is the output of iwconfig, route -n, lspci, and what happens when I ping other network
Iwconfig:
eth0 Link encap:Ethernet HWaddr 00:1d:72:9e:09:8f
UP BROADCAST MULTICAST MTU:1500 Metric:1
[code]....
View 2 Replies
View Related
May 3, 2011
I just loaded Ubuntu 11.04 onto Acer Aspire 5100 computer. I can access the internet through Firefox when I connect ethernet lan cable but it doesn't work when I use wireless connection. Although I do get the indicator in top right that says my wireless connection was established. Why I can't access internet with Firefox in wireless mode? I tried toggling the wireless switch in front of Acer but that didn't work.
View 9 Replies
View Related
Aug 26, 2011
I have installed ubuntu 10.04 and STA wireless driver. I am using a wimax modem, the wireless is connected (have IP addresses) but I do not have access to the internet.I also have installed a windows XP as a guest OS (ubuntu is the host) on vmware. By using a bridged network connection, I am able to access internet. So I guess the problem is related to the ubuntu wireless driver.
View 9 Replies
View Related
Jan 26, 2010
With Encrypted Wireless Connection Not Able to Access Internet - no pings, internet browsing, etc. However, without encryption I am able to browse the internet. I need encryption ..
I am pasting diagnostics collected by shell procedure collectNWdata.sh..
Code:
collectNWData.sh V0.6.2.0 (Rev: 1.193, Build: 2010/01/20 21:22:30 UTC)
--- Which type of your network connection should be tested?
--- (2) Wireless connection (WLAN)
--- What's the type of networktopology?
[Code].....
View 8 Replies
View Related
Apr 13, 2010
I spent $70 on a brand-new Wireless-N adapter for my Ubuntu computer in hopes that I could get it to connect to the main router in the house and get me internet access. However, the driver install CD is designed for Windows and thus will not run. I have tried to get it to set up, but it takes no action when plugged in and I am still without access to the internet. what I can do to get my computer connected and save me from having wasted $70?
View 9 Replies
View Related
Oct 27, 2010
At work, we (like almost everyone) are still full-on windows. I am currently trying to get away from windows because I am not a fan. my current windows machine (different from my Ubuntu machine) is accessing the wireless network fine, and there are no obvious problems there. Also, my Ubuntu machine can access my wireless network at home, so I know there are no driver issues. I set up the connection for the Ubuntu machine, and it seems to be connecting OK. I can ping internal IPs and by all statuses, the connection to the router is functioning. However, when I attempt to load a web page or ping a domain or external IP, it fails. I tried to ping the IP, thinking if that worked, it's probably the DNS, but pinging both domains or IPs fails. I have looked around at forums and posts, but none of them seem to match my issue (that's probably not true, but I am struggling to see the commonality).
Here are the results of "netstat -r":
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.45.0 * 255.255.255.0 U 2 0 0 wlan0
link-local * 255.255.0.0 U 1000 0 0 wlan0
default 192.168.45.5 0.0.0.0 UG 0 0 0 wlan0
And here is "ifconfig":
wlan0 Link encao:Ethernet HWaddr 74:f0:6d:XX:XX:XX
inet addr:192.168.45.49 Bcast:192.168.45.255 Mask:255.255.255.0
inet6 addr:fe80::76f0:6dff:XXXX:XXXX/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
View 3 Replies
View Related
Jan 20, 2011
I have had a heck of a time trying to get my laptop running ubuntu to connect to my home network. I have managed to get it to work at my university which would seemingly be more difficult than getting it to work at home, so I know for a fact it isn't a hardware or driver issue. If I try to connect via ethernet cable from my router, it detects that I connected the cable but says "disconnected" and never lets me connect. If I SKIP the router and go from my modem directly to my laptop via ethernet cable it works great.
Using the wireless network tool I can see all of the wireless connections in my area. When I go to connect to my network it prompts me for the WEP key and when I enter it and hit connect it just keeps cycling and eventually times out and finally again prompts me for my WEP key. I know this network works as it works just fine on my Windows 7 partition. Another interesting note - both my wireless and ethernet connections both worked flawlessly and stoopid easily on the live cd but don't after the full install.
If I manually enter in the information for my wireless through IPv4 settings and enter in the Address,Netmask and gateway I can connect to my network - but then I have no active internet connection. Same deal with my wired connection. Is this because choosing this manual method grays out the DHCP?
View 5 Replies
View Related
Feb 10, 2011
I am trying to connect to the college campus wifi network, but having difficulties in Linux.I am dual-booting Windows 7 and Ubuntu 10.10, and I use Google Chrome web browser on both. When I boot into Windows, my laptop connects to the network (as I can see from the taskbar icon) and I can (and currently am) connect in Chrome.However, in Ubuntu, it connects (or so the icon indicates) but Chrome doesn't load any pages.The campus network is unsecured, but once you open the browser, you are prompted with a log-in page (student ID and password) to actually connect.Here is my output for iwconfig:
Code:
wlan0 IEEE 802.11bgn ESSID:"sjsu_campus"
Mode:Managed Frequency:2.412 GHz Access Point: 00:24:6C:BC:D3:E0
Bit Rate=54 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
[code]....
View 1 Replies
View Related
Jun 28, 2010
Just installed Fedora 13 about an hour ago. I've googlled and googled but can't get my RTL8192E wireless card working in my netbook. I've had it working in ubuntu netbook remix via ndiswrapper but for the life of me I can't figure out how to get ndiswrapper and ndiswrapper gui installed to attempt to install driver.
View 1 Replies
View Related
May 8, 2009
I am building a CarPC which I'd like to have wireless internet access on. I have Verizon phone service so if there is a Verizon air card (not wireless card, an air card so I can have constant access without having to search for hot spots) that would work with Fedora 10 I would be very happy. I don't really know where to start and I can't find too much on Google, so I'm just looking for what options are available.
View 3 Replies
View Related
Sep 17, 2009
if i'm connected to my wireless network it only gives me internet acces for a few minutes. The connection with my network stays but i have to close it back of and reconnect before i get back online.
View 1 Replies
View Related
Aug 8, 2010
I started using Arch just a few days ago. forward traffic to the Wireless access point I created on arch. i am using cable internet (ppp0) which I want to share via a usb wifi adapter running as a WAP. I followed the instructions in this link to enable the AP mode. Afterwards I followed the instructions provided in the Arch Wiki to forward the traffic but because of my inexperience I am still unable to connect to the internet. Here is the output of iptables -nvL :
Code:
Chain INPUT (policy DROP 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
77 31312 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0
0 0 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID
[code]....
View 2 Replies
View Related
Jun 1, 2010
I am not really that good with linux, yet, I have a smc 2602W v3 wireless pci card, and I want to install it on linux, so I could access the internet, but I haven't found any solutions yet. Btw latest ubuntu desktop version. Info about the card: [URL]
View 3 Replies
View Related
Jun 5, 2010
I have I fileserver on my home network. It has a static IP and is plugged into the back of the wireless router. It is fine on the network but cannot access the internet. I noticed this when I was trying to update my package list. This is what is in /network/ interfaces:
auto eth0
iface eth0 inet static
address 192.168.2.100
netmask 255.255.255.0
network 192.168.2.1
broadcast 192.168.2.255
gateway 192.168.2.1
[Code]...
View 2 Replies
View Related
May 22, 2010
I just installed the Ubuntu Netbook Remix on my netbook and the wireless internet no longer works?
View 1 Replies
View Related
Mar 4, 2011
I am wanting a computer with an external dialup modem (ppp0 modem through a com port /dev/ttys1) to act as a gateway to the internet, forwarding internet traffic through ethernet (eth0 is set to static 192.168.2.2) to a router (the router is 192.168.2.1) where it will be broadcast to other wireless computers like my laptop (192.168.2.3). I've had this setup until recently when the gateway computer (the one with the modem) died. Now I'm replacing that machine with another box and an install of Ubuntu 10.10 but so far things aren't working for me.
Success so far:I have dialup access working on the new box. Took me a while to work out the configuration for getting dialup working, though the IP address is Dynamic (or it won't stay connected), "Check carrier line" is off, and "Ignore Terminal Strings (stupid mode)" is on in order to successfully connect and stay connected to my ISP. I also had to make my normal (non-root) user "lancer" a member of the "pid" group (the reboot) in order to use gnome-ppp as non-root. The laptop (192.168.2.3) is successfully connecting to the router (192.168.2.1) as I can see the router configuration page when I type http://192.168.2.1 into the laptop's web browser. This setup is unchanged from how I had it before when this was previously working and I don't want to change how the router itself is set up. What I want is to know what to fix in the new box in order to get it connected to the router (through ethernet) and bridging the internet through.
My problem is that whenever I plug in the eth0 from the gateway (192.168.2.2) to the router (192.168.2.1), Ubuntu's automatic plug-me-in network detection kicks in and I find my dialup no longer working through some kind of IP conflict (at least that's what I think it is). Maybe I don't have the "gateway" correctly assigned? (in the gateway computer for the ethernet connection, I had it pointing to itself as I don't know what to put for "gateway IP" as that is automatic So, just to check my connection, here I am pinging google (from the gateway computer which has the dialup modem) once a dialup connection has been made.
Code:
lancer@lancer-desktop:~$ ping www.google.com
PING www.l.google.com (74.125.237.17) 56(84) bytes of data.
64 bytes from 74.125.237.17: icmp_req=1 ttl=55 time=179 ms
64 bytes from 74.125.237.17: icmp_req=2 ttl=55 time=176 ms
64 bytes from 74.125.237.17: icmp_req=3 ttl=55 time=158 ms
[Code]...
What do I need to do in order to make Ubuntu of my gateway computer stay connected to my dialup but also simultaneously share an ethernet LAN to my wireless router and feed traffic to the other computers from there? I have googled this but some of the most promising instruction (e.g. http://www.ubuntugeek.com/sharing-in...in-ubuntu.html) call for packages like dnsmasq or ipmasq which seem defunct now in Ubuntu 10.10. Other pages seem to suggest dual-networks "can't be done" in Ubuntu [URL].. (what!?! I had it before my other gateway died)
View 1 Replies
View Related
Nov 11, 2010
I just installed UNR 10.10 on my Acer AspireOne D255 netbook.
I've installed the broadcom driver it wanted me to, so it enabled wireless networks, HOWEVER, none show up.
I used to have the Acer AspireOne 531h with UNR 10.04, and the wireless worked out of the box.
What can I do to get it to recognize wireless networks?
I tested it with a wired connection and it worked.
View 3 Replies
View Related
Aug 8, 2010
I have a Samsung phone (S3310) and I'm trying use it as a modem to access the net on 10.04. I set up a Mobile broadband connection (under network connections) and I'm pretty sure the settings are correct because it works on a Nokia phone with the same service provider.
When I plug in my Data Cable and set it to Samsung PC Studio mode, my phone isn't detected as a modem. I just tried wvdialconf and it says "No modem detected". I'm guessing that maybe I'm missing some drivers here. what I can do get the phone detected as a modem.
View 5 Replies
View Related
Apr 14, 2010
I just bought a samsung r580 laptop. this is the first time i've ever owned a laptop. I have owned a pc with ubuntu 8.04 installed on it and the internet worked trouble free. Now I have windows 7 and ubuntu 9.10 dual booted on my samsung r580. I used wubi to install and the internet works fine in windows but will not work in ubuntu. I have been trying to get this to work for about 5 hours now
View 6 Replies
View Related
Mar 5, 2011
I have just purchased the Samsung N150 net-book. The reason for purchasing was so I could watch movies, listen to music and browse on the go. It came with windows 7 starter and a load of pre installed Samsung crap. I was wondering whether Ubuntu would be a better choice for me since I only really want, Chrome, VLC, Spotify, MSN and Dev++ compiler.
I am very computer literate doing programming at Uni, but have not used Linux before. Also there's loads of Samsung software for extending battery life or something. Will I be able to install that on Ubuntu or not?
View 6 Replies
View Related
