Ubuntu Networking :: Realtek Rtl8192se Disappears On 11.04?
May 24, 2011
After having installed ubuntu 11.04 my laptop's wireless device (realtek rtl8192se on a packard bell laptop) disappears on ubuntu 11.04. Before, with ubuntu 10.10, I had no problems. Now, when I start ubuntu 11.04, sometimes the wireless card work, but most of times it doesn't: the wireless led is off, and with the lspci command I got no line about wireless card. If I restart the laptop and I start win7, the wireless card doesn't work there too! only after many reboots and/or shutdowns wireless card appears again.
View 1 Replies
ADVERTISEMENT
May 15, 2011
Not too many entries for this Realtek product in the forum, but it appears that the commands MAKE and MAKE INSTALL do not work in opensuse 11.4 for the above Realtek NIC. I suspect that it is Realtek's driver which is a tar.gz file and the problem. They do not provide either an rpm or deb file.
Is there anyone out there who has had success with this driver in opensuse 11.4, or for that matter, opensuse 11.3?
View 9 Replies
View Related
Aug 15, 2011
I have just installed an Edimax EW-7612PIn PCI-E Wifi card which has an RTL8192SE chipset. This chipset is not supported under current F15 kernels so I have installed the driver and firmware from source and have that working fine. The driver can see the card and I can issue 'iwconfig' commands successfully enough to see my Wifi network.
The problem I have is that I don't understand the relationship between iwconfig and wpa_supplicatant and as I'm running a headless F15 server I cannot use the NetworkManager GUI to help me. I should also note that the Wifi network is using WPA2-Personal encryption.
This is what I have done:
Configured /etc/sysconfig/network-scripts/ifcfg-wlan0 with what I think are reasonable values (based on google searches), including the ESSID, TYPE as Wireless, etc.
Configured /etc/wpa_supplicant/wpa_supplicant.conf, including using the key value returned from wpa_passphrase.
Arranged for wpa_supplicant to run from boot, using chkconfig.
However when I run 'ifconfig wlan0 up' I get the error message 'link is not ready' and indeed looking at the output from 'iwconfig wlan0' there are no configured values. I also understand that some values are configured by iwconfig and others by wpa_supplicant, however it's not clear what.
How do I permanently set iwconfig values?
How do I configure wpa_supplicant?
View 3 Replies
View Related
Apr 10, 2011
I am running Debian 6 & picked up a wireless nic for my desktop since I want to locate it in an area that would be a challenge to wire. I downloaded the driver and ran make and got the strange error below. I tried doing some web research but could not find anything. I also booted up the machine w/ a Ubuntu Live disk to ensure the card was good and found no issues ( I also have the same nic in my kids machine running Ubuntu 10.10. )
[code]...
View 10 Replies
View Related
Jan 24, 2010
the wireless connection works very well when i start using. but once, after my sister took hold of my computer for a moment. the wireless don't seem to work anymore. i asked her what she did but she says nothing. she may ot may not be lying but that doesn't matters. what matters is i cant reinstall back the wireless network.when i first formatted my notebook to ubuntu 8.0, i followed an online instruction to enable wifi to work. it works perfectly well. so when the problems occured, i tried using the same instruction but it doesn't work anymore.
the wireless network does not appears under connection anymore.
View 4 Replies
View Related
Mar 3, 2010
Out of the blue a dialog popped up requesting that I enter the key for my home wireless network. This is of course unexpected since the correct key is defined for that network in my network config. I entered the correct key but it was rejected. I then clicked on the network manager icon in the task bar. Contrary to normal behavior this did not show either my home network or any of the other wireless networks from my neighbors. The only resolution I could find to restore the wireless network was restarting my system. This seems excessive.
View 1 Replies
View Related
Jul 8, 2009
The problem in a sentence: a F10 machine seems to disappear from the network after running for a couple of days, however, the network is accessible from the machine itself. My setup: A router with two machines connected via ethernet. Both are essentially desktop computers, one is a standard machine that is booted every day (let's call it Desktop) and the other runs continuously, having only a keyboard attached (let's call it Server).
After running for a few days, Server becomes inaccessible from Desktop. It doesn't respond to ping, ssh fails etc. Even the router shows that Server is disconnected from the network. There is a ping running in Server that pings a machine in the internet with an interval of 60 seconds, the output is directed to a file. The file shows no failed pings, it even succeeds when the router shows that Server is disconnected.
The most peculiar thing: a random keyboard event (e.g. pressing Shift) will make Server reappear. I don't have to do anything else, just press Shift on Server's keyboard and a few moments later everything is back to normal. The router shows that Server is connected and I'm able to do ssh to Server.
View 14 Replies
View Related
Jan 28, 2010
On about 90% of bootups I find that network manager has disappeared from the notification area to be replaced by a random duplicate of one of the other icons (at random). If I remove the notification area and add it again all is fine.
View 9 Replies
View Related
Sep 10, 2009
I have a problem with samba machine disappearing after I restart smb or the server where samba is running. Lets say I name my samba server ABC and set it up via system-config-samba utils. I follow basic steps and fill out everything according to most guides that are available for fedora. After that everything works great, I can connect to samba server ABC form any machine through smb://ABC (mac) or \ABC (win), however as soon as I restart smb services or my server (subsequently restarting the smb service ...) I no longer can connect to it via samba server name ABC, I can only do smb://SambaServerIP or \SambaServerIP (have to put numerical internal ip to connect)
My smb.conf:
# cat /etc/samba/smb.conf
[global]
[code]....
View 1 Replies
View Related
Feb 15, 2010
I am brand new to ubuntu (I installed it about 2 hours ago on my new PC). Everything so far has seemed really easy and straight-forward, but I am having problems trying to connect to my wireless network.
I have a Realtek 8185 wireless card, and have the disk with the inf file on it. I installed ndisgtk but when I pointed it to the inf file, I got an "error while installing" message, then it showed up in the list of currently installed drivers in ndisgtk but as an invalid driver. I'm not really sure what I'm doing wrong.
I actually have another wireless card in my old PC (a belkin of some sort) - would I be better off using that? I'm using an ethernet cable at the moment and it works absolutely fine, I just plugged it in and off I went.
View 1 Replies
View Related
Feb 26, 2010
I have a white label netbook with the Realtek RT8187SE Wireless card on PCIe. It is not detecting wireless networks consistently. When I am even 1 meter from the wireless router, I get no networks in range, but sometimes I pick up networks that are more than 20 meters from me. I can not connect, even if it is unsecure.
WiFi Radar does not detect the card. If I run a system check on the PCI bus I get the following: 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8187SE Wireless LAN Controller (rev 22) Subsystem: Realtek Semiconductor Co., Ltd. RTL8187SE Wireless LAN Controller Flags: bus master, fast devsel, latency 0, IRQ 17
[Code]...
View 3 Replies
View Related
Jul 24, 2010
I've had this problem ever since I've installed this ethernet card in the PC (after the 'effin integrated one blew off for some reason), I wasn't ever able to make the networking work again. Every time I try to trigger the PPPoE connection (DSL), the PPP configurator keeps on looking for the concentrator, reaches over 100% and stayed like that for 1 hour. Here's the terminal log of everything that I've tried:
Code:
~$ sudo lshw -C network
*-network
description: Ethernet interface
product: RTL8139D [Realtek] PCI 10/100BaseTX ethernet adaptor
vendor: Hangzhou Silan Microelectronics Co., Ltd.
[Code]...
View 9 Replies
View Related
Oct 12, 2010
I have an ASUS M4A785-m and it has the Realtek 8112L gigabit nic. The weird thing is, the 10.10 rc saw the nic card just fine, and windows sees the card so it's not disabled in the bios.
Ubuntu says i have no network connections and i need to get internet. Any suggestions?
I should also note that i'm running from the livecd and lspci shows that it detects my NIC. but my NIC isn't "detected" in that it can be used.
View 5 Replies
View Related
Jan 1, 2011
I have tried ndiswrapper using 32 bit and 64 bit winxp drivers and the 32 bit driver just doesn't work period (as expected.) The 64 bit driver locked the system up completely and I ended up reinstalling ubunto. I have now reinstalled and updated and upgraded ubunto 10 times in the last 3 days of trying to get this to work and need some external!
using
Code:
lshw -C network
I do see my network card and driver.
Where I am at currently: I have a fresh install of ubunto 10.04 with it upgraded and updated. I do not have ndiswrapper gtk installed and I have not downloaded any drivers for the wireless card.
View 9 Replies
View Related
Jan 14, 2011
Bus 001 Device 007: ID 0bda:8171 Realtek Semiconductor Corp. RTL8188SU 802.11n WLAN Adapter this adapter shows up in network manager when connected to computer but doesn't detect network and cant connect to any network I have setup in nm, the adapter works fine in windows and it's supposed to work in linux or do I have to install drivers?
View 8 Replies
View Related
Mar 19, 2011
Ubuntu 10.10 - the Maverick Meerkat � (Installed .iso from cd)The router has a password that I'm not sure if is wep or wpa.When I manually put in the address, netmask,gateway, dns,domain my Realtek usb adapter is connecting to the router but is not receiving packets.I got the driver installed with ndiswrapper.I'm trying to figure out wpa_supplicant
View 5 Replies
View Related
Apr 17, 2011
I recently installed ubuntu on my computer and when i put in my network wireless usb adapter (Realtek RTL8191SU) it isn't recognize, and the internet doesn't work. When I do lsusb, it comes up with Realtek Corperation however. And also the light on it doesn't flash either.
View 9 Replies
View Related
Apr 26, 2011
trying to get my little Encore USB wireless adapter to work on several flavors of Linux (Ubuntu 10,10, ElementOS, Xubuntu, and Puppy), I emailed tech support at Realtek. I asked where is the Linux driver for this product? I did this because there were no Linux drivers posted on their site and everyone here (and on Newegg) is jumping though hoops trying to get a working wireless connection with the Encore and similar dongles that use the RT8187b chipset. I didn't expect an answer, but felt better after my little vent. I get an email from Realtek with a driver. Realtek needs to promote Jerry -- a beacon of customer service in the age of the "get lost" school of customer relations. I have attached the driver below. Caveat: I have not yet compiled the driver, so I don't know much more about it than I've said already, although the archive appears to contain the source code.
View 3 Replies
View Related
May 22, 2011
i'm having troubles with setting my wireless driver on ubuntu 11.04
this is the closest i ever got to a solution: i found this [URL] which led me to these drivers [URL] but i have no ideia how to make it work
View 5 Replies
View Related
Jun 29, 2011
After compiling the Realtek drivers from their page (ver 8.024), installing the module, blacklisting r8169 and updating the initramfs, I still can't get the network card working.The card is listed in lshw as RTL8111/8168B PCI Express Gigabit Ethernet controller.lsmod shows only r8168.dmesg keeps spitting once and again, every second or so the following:
Code:
[ 1293.452274] r8168: eth0: link up
[ 1294.449785] r8168: eth0: link down
[code]....
View 5 Replies
View Related
May 7, 2010
When using a Verizon UM150 aircard, it is quickly recognized in Ubuntu 10.04. It installs and connects quickly and seamlessly. After anywhere from a few seconds to a few minutes it disconnects and then disappears from the network manager. To reconnect I have to exit and reboot into Ubuntu. I suspect that there is a conflicting driver that needs to be blacklisted.
View 5 Replies
View Related
Nov 18, 2009
I am trying to set up bridge, and everything seems to be ok, except 1 thing, it disappears after reboot. So, what I am doing:
Code:
brctl addbr br0
brctl addif br0 eth0
and adding /etc/sysconfig/network-scripts/ifcfg-br0, here it is:
Code:
GATEWAY=192.168.1.1
DEVICE=br0
BOOTPROTO=none
NETMASK=255.255.255.0
DNS1=208.67.222.222
DNS2=208.67.220.220
TYPE=bridge
HWADDR=00:18:f3:75:18:78
IPADDR=192.168.1.3
IPV6INIT=no
ONBOOT=yes
USERCTL=no
and my ifcfg-eth0 is:
Code:
GATEWAY=192.168.1.1
DEVICE=eth0
BOOTPROTO=none
NETMASK=255.255.255.0
DNS1=208.67.222.222
DNS2=208.67.220.220
TYPE=bridge
HWADDR=00:18:f3:75:18:78
IPADDR=192.168.1.3
IPV6INIT=no
ONBOOT=yes
USERCTL=no
How to make it working after reboot?
View 1 Replies
View Related
Feb 16, 2010
I have downloaded the driver installed it, and it works fine. But i can't get to turn it off. I do have the ability to unload the driver's kernel modules and the sysyem does not see my card after that. That's ok, but i'm thinking it still uses my battery power. The wifi led is always on no matter what i do. The fn+<wifi key> doesn't to anything.
View 8 Replies
View Related
Apr 27, 2010
I have a problem with my internet connection this is the picture the device is Realtek RTL8187. i didn't know how can i manage this device to work so could you help me i don't have an internet connection in ubuntu right know and i really wanna move to ubntu my verison is 9.10
View 9 Replies
View Related
May 12, 2010
Im not able to establish a Wireless Internet connection in Ubuntu 10.04.
Ive tried these steps:
1. Wireless Internet did not show via the Network-icon. Only the 2 LAN-gates where shown
2. I installed the Windows Driver (net8185.inf) via ndisgtk package
3. After restarting the computer, 2 LAN-gates and 1 WLAN where listed via the Network-icon
4. Normally WLAN should automatically start scanning for available networks, but that didnt happen
5. When I tried to connect to my own network, the computer tries to connect for 1 minute and than stops because no connection could be established
6. A wired Internet-connection does not give any problems
Details:
- I first had Ubuntu 9.10 but I wasnt able to make a WLAN connection either. I followed the same steps. After that I upgraded to 10.04
- iwconfig in Terminal gives an IP-address which consists of 12 identical characters.
- lspci in Terminal shows these data:
01:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5787M Gigabit Ethernet PCI Express (rev 02)
[Code]....
My questions:
- How to create an Internet connection via my WLAN-card?
- How to install the option to search for available networks automatically?
View 9 Replies
View Related
May 21, 2010
I have installed 9.04 ( I currently have it on dual boot with Windows XP) and my problem is that I have no internet connection. I have a Motorola modem with a Realtek RTL8139 Family Fast Ethernet NIC network card ( it's a wired connection, btw) When I plug in the cable, there's a little animation, but after a while I get the message: Wired connection is not active (or something like that) Here's what I did so far:
1) I ticked the Wake-On-Lan option in XP, since I read it in the forums that I could solve my problem. It did not
2) I turned off my modem, rebooted my system.
3) I deleted the Auto Ethernet network, and plugged in the cable again...no use.
4) I did an ifconfig, since I know that is what you guys really want
evajulia@Derek:~$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:18:f3:ab:2b:3a
inet6 addr: fe80::218:f3ff:feab:2b3a/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
View 9 Replies
View Related
Jun 13, 2010
I recently purchased two MSI Windtop AE2220's. One for my home which uses a router with WPA2 protection and one for my office where I use WEP encryption.
The Realtek internal wireless card will not connect to a WEP router if you are running Ubuntu Lucid Lynx 10.04. I have exhausted all suggestions on this site and all drivers found at Realtek's site.
I have been using Ubuntu since Hardy Heron, but sadly, painfully, I have had to install Windows 7 on my office machine until I find a wireless card compatible with the MSI Windtop AE2220, Lucid and WEP.
View 5 Replies
View Related
Jul 25, 2010
I am using ubuntu 10.04lts on my compaq615 laptop, which has a realtek wireless card, with which I had a few issues to get it to work.
Here is what I had to do:
When I do this, it works beautifully, after setting my router to open I may add.
So, as I said it is probably the fastest wireless I have ever experienced, but my problem is this, everytime I switch my laptop on I have to re-install, starting at:
View 7 Replies
View Related
Aug 15, 2010
I have a Toshiba Satellite L655-S5061 laptop and dual-boot Windows 7 and Kubuntu Lucid Lynx. Windows detects and connects to the wireless network just fine, but in Kubuntu it will detect the network but can't connect to it. Sometimes Network Manager will say it's connected, but Konqueror can't load any websites. Plugging in an ethernet cable doesn't give me access to the internet, either.
View 2 Replies
View Related
Sep 16, 2010
I was able to successfully install the drivers on the generic kernel, but I seem to be having a problem getting it done on the real time kernel I downloaded via the Ubuntu Software Center. Here's what shows up when I type in 'make' at the command line:
Quote:
/driver/rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.20100 625$ make
make ARCH=i386 CROSS_COMPILE= -C /lib/modules/2.6.31-11-rt/build M=/home/marcoharder/rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.20100 625/driver/rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.20100 625 modules
[Code].....
View 8 Replies
View Related
