I have a Lenovo W510 Laptop with Ubuntu 10.04. The laptop has an on board Qualcomm 3g modem. I have managed to install the Qualcomm firmware and Network Manager detects the 3g device but when I try to connect it disconnects after a few seconds. My syslog has the error
Code: Got failure code 100: Unknown error
cdma usb modem recognized on as mass storage device.nstalled wvdialler and made appropriate lines to conf file and still does not work.
View 5 Replies View RelatedBasically upon logging network manager will connect to my network, and most of the time it will only last 20 seconds or so before it disconnects and tries to reconnects, this tends to go on for quite a while. Logging off and logging on over and over worked once, for this post I opened pages between the 15 seconds that i was connected and after 20 minutes it has remained connected (every time it stays connected for longer than 5 minutes it will never disconnect again) I followed the HOWTO thread so forgive me if most of this information is useless
1 ) Machine Brand and Model (Laptop): Asus 52jr is the model number
2 ) Wireless Brand, Model and Wireless Chipset:
03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)is what I found from running lspci
3 ) check interface:
Code:
wlan0 Link encap:Ethernet HWaddr 1c:4b:d6:5c:61:8b
inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::1e4b:d6ff:fe5c:618b/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
I'm currently on F11, and experienced problems with Network Manager. Whenever I to connect to a network, wired or wireless, it just seems to try to connect, and then after 2-3 seconds, it just reports "Disconnected"..
Then I switched to network, and both wired and wireless works. so I don't think there is any driver or hardware issue...
Does anyone have any idea of this problem? The network manager have worked on the live CD version ( before installed to HD).
running Ubuntu 9.10 x64bit fresh install and updated.When I connect with my 3g um150 modem it disconnects my home network?? I cannot get them to run both at the same time and of cousre the next thing would be to share the internet connection.
View 9 Replies View RelatedI run KVM on 9.10 host and guest 9.10. Both are x64. When I halt the guest os:
My host OS looses its connection with internet for 10-15 seconds and then it comes back on. Probably something goes wrong with default gateway, as it looses only external network (I still can reach it on my internal network). I've googled a lot, but cant find anything about that. I use bridged network.
I use an analog modem and wifi to access the internet. I am using Ubuntu LTS 8.04 on a laptop and have an analog modem connected via USB serial cable. The dialup feature and the modem work flawlessly. I am testing LTS 10.04.1 on a live USB drive that I purchased preinstalled from On-Disk. On the live USB drive, I am able to get a dialup connection with my ISP long enough to pull up a web page with the browser. However, the analog modem disconnects within minutes with exit codes 16 or 17.
Man pppd:
16 The link was terminated by the modem hanging up.
17 The PPP negotiation failed because serial loopback was detected.
My questions are, how to do I track down the dialup setting(s), or file configuration(s) that is causing the disconnects? Is the problem likely due to a poorly worded AT modem command? I want to get this problem resolved before I proceed with upgrading from 8.04 to 10.04.1.
I recently bought a IOgear USB bluetooth adapter and a Sony DRBT101/BLK bluetooth headphones to use with my computer.Whenever I try to make a call using these headphones with skype, I can speak for say 10 seconds and then the headset disconnects completely from the system. I then have to reconnect the headset by switching it off and on. I do not have this problem listening to music using A2DP. It works fine with my mobile phone.When I change the profile to Telephony Duplex (HSP/HFP), it shows up as hands free, I thought it should be headset in blueman manager. My friend uses Plantronics headset with is Dell laptop with built in bluetooth and he says his comes up as headset not hands free. Could this be causing the problem?
View 1 Replies View RelatedI am having a problem with my Fedora11, I am not sure wether it is software or hardware but this looks serious. My computer is running very slow and freezes up every few seconds. Every time I reboot I would get a kernel failure pop-up.
This is what the message says:
Kernel failure message 1:
Kernel failure message 2:
Call Trace:
I am trying to setup HylaFax server on Ubuntu 10.04 Server with an external COM Rockwell modem, but no success yetEverything works fine except when I try to send fax. I get an error saying: Failure to train remote modem at 2400 bps or minimum speed.I have searched Hylafax mailing lists but no luck.Does anyone had the same problem? Any ideas to solve it?
View 1 Replies View RelatedI have failed to install an AT&T Sierra Wireless Aircard 881 on a Compaq 8510p running RHEL5 Server (Linux version 2.6.18-164.9.1.el5,gcc version 4.1.2 20080704, Red Hat 4.1.2-46. )
As seen in the dmesg output below, the OS detects the modem, connects it to ttyUSB0 - ttyUSB3. However, kppp is unable to access the modem.
I have followed Sierra Wireless instructions located at sierra wireless's website. (I would post it, but I've not made enough posts yet to link it in this message.) However, I was not able install the TRU-Install patch. The unusual_devs.h is absent on the machine, so patching was unsuccessful.
I'm stumped on what to try next. Is there a FAQ or guide on how to get a 3G modem running with RHEL5 Server? Ideally, I'd like to find something like the Internet Connection manager on Ubuntu. The modem works on that distro with no problems. I'm not able to migrate due to application and security certification dependencies on RHEL5 Server.
lsusb output:
Bus 009 Device 001: ID 0000:0000
Bus 008 Device 002: ID 1199:6851 Sierra Wireless, Inc. AirCard 881 Device
Bus 008 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 007 Device 001: ID 0000:0000
[Code].....
OpenSUSE 11.1; kernel 2.6.31.12-0.2-default
Tried to configure via:
Zoom CD driver: 1.06_k2.6.22.17_01_default-1suse.i586.rpm
linuxant driver: dgcmodem-1.13_k2.6.31.5_0.1_pae-1suse.i586.rpm
[code]....
find and install modem driver for the Alcatel X200 USB modem?
I've been all over the internet trying to locate Linux drivers but no success. Alcatel's website says is not supported, only in Windows. I'm sure there's gotta be a way to use the X200 in Linux.
i'm running Kubuntu karmic and i've been using a 3G Huawei E1552 modem to connect to the internet, everything was going well when suddenly my modem stopped working. I've tried reconfiguring everything, i even reinstalled kubuntu from scratch with no success.Here's a part of my /var/log/debug
HTML Code:
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099883] usb-storage: device found at 7
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099888] usb-storage: waiting for device to
[code].....
I don't know how to make my Wifi Card Qualcomm Atheros QCA9377 to work on my Debian Jessie.
I found driver here: [URL] .....
Tintumon2 said it work for him on Ubuntu 14, but how can I make it to work on Debian?
@update:
When I try to install them on Debian using "./install.sh" I see black screen and then GNU/Linux reboots.
I'm trying to sync a folder between my Windows install and my PCLinux install. Same machine, Windows 7 on the C drive and Linux on an external USB hard drive.
Using the Grsync GUI, I searched for the source and destination folders, and then executed the command. Here is the output:
** Launching RSYNC command (simulation mode): pkexec rsync -r -n -t -v --progress -s /media/Win7/Documents and Settings/Paul/Application Data/The Word file:///root/.wine/drive_c/Program Files/The Word/myData
ssh: connect to host file port 22: No route to host
rsync: connection unexpectedly closed (0 bytes received so far) [sender]
rsync error: unexplained error (code 255) at io.c(601) [sender=3.0.7]
Rsync process exit status: 255
It seems to be doing an FTP operation, whereas all I need is a file transfer. Can anyone point out my error here?
When I use all the band(transmission or browsing too many videos) it disconnects after few minutes and it doesn't connect again until I reboot.
lspci:
05:01.0 Network controller: RaLink RT2760 Wireless 802.11n 1T/2R Cardbus
Code:
sudo lshw -C network
*-network
description: Ethernet interface
product: 88E8056 PCI-E Gigabit Ethernet Controller
[Code].....
I could use N and WPA2 by following this thread. If it is possible to reconnect without reboot would be a possible workaround
(I use Ubuntu Karmic x_64)
My internet disconnect mabe every second hour and I have to restart the Ubuntu to get internet again. This started to happen when I bought a new wireless card called NETGEAR WG311v3. The live CD didnt have the drivers for it so I had to download XP drivers and install it with ndisrwapper.
So my question is how do I fix it? Do other network drivers crash with my current one? If so how can I see wish one to remove?
Note that my card works fine with XP on same computer.
I have loaded ubuntu Lynx 10.04.1 as a dual boot behind XP home. I have wireless connection to the XP os via netgear wireless G router and USB 2.0 adapter. The network connection works well with the XP side. When I boot into ubuntu I am sure I have configured the network properly with the wep key and password and the network signal is alive in the work bar at the top of the screen. When I open Firefox and try to browse to ,say, ebay it asks for the passphrase again then tells me that FF is in work offline mode. When I correct this I get asked for the pass phrase again and the connection is disengaged. It just keeps asking for the passphrase and disconnecting. When I reboot into XP everything works perfectly again.
View 9 Replies View RelatedI'm using an Acer Aspire One d250 running Netubuntu 10.04. The wireless connection to my router fails at random intervals and spends most of it's time trying to reconnect. It will occasionally ask me to input the password to the network, which is already entered in the dialog box, and clicking "connect" doesn't seem to make any difference. Also, when it is disconnected from the network, none of the other computers in the house, wired or wireless, are having any problems. If there is any more information I could provide,
View 1 Replies View RelatedI have experienced sudden wifi disconnects. My laptop fails to reconnect even after repeated attempts. It is only after a reboot that I am able to connect to the wireless.
View 1 Replies View RelatedI use ubuntu 10.10 and disconnects from wireless at random. after it reconnects the the connection speed is very slow and unstable. It's not my router because it works fine on my sister's netbook (which is also running ubuntu) and it worked fine when I was running windows? I'm not very advanced with linux so you know. I don't have IPv6 enabled. My laptop is an "Advent QRC430" my wireless card is QCOM Q802XKG Wireless Network Card.
View 1 Replies View RelatedI have a minor Internet issue. I have a static IP address with the modem acting as a gateway only to my ISP. My Ubuntu server hosts my public IP address and I use pppoeconf to connect. Every 3 hours I lose Internet. I have wrote a short script to reconnect. I doubt that it is my ISP trying to renew that often.
View 8 Replies View RelatedI just installed Ubuntu this morning and don't have much time to detail my problem before my internet goes out again. I am currently running Ubuntu 9.10 (Karmic Koala?). I just got this laptop earlier this week with windows 7 and decided to put ubuntu on it via Wubi. Anyhoo, I login and then enter my wifi password and eveythings fine. I can surf the internet for a bit and everythings fine. but after a while, the wireless indicator on the keyboard begins to flicker on and off (between a connection and no connection) then starts to stall. The first thing I did was install google chrome (always the first thing to do) and I accidentally downloaded the wrong version A-OK. After I saw I downloaded the wrong version, I downloaded the correct, 32-bit version and installed it. During the download it said I had a 750kBs speed, but took much longer to download than had it been downloaded at a consistent 750kBs speed. I then tried to use update synaptic and it began to download reload all 44 packages and stalled around 38 or so. My internet then disconnected (wouldn't reconnect) and the download failed. I went back into windows uninstalled Ubuntu and then reinstalled it. After going through the first few steps again I began to update via update manager and surfed the web. After a few minutes of surfing the indicator began to flicker than just went off. I then connected to my neighbors internet, continued surfing and then the internet just crashed. I've found that when its just lightweight surfing, everythings okay, but during a download or any 2.0 surfing, then things start to get funky.
View 4 Replies View RelatedMy wireless disconnects after around 10 minutes. It does not reconnect automatically. I've to pull out the usb dongle and then put it back in to connect again.
[Code]....
I upgraded to Karmic the other day and my Wireless Internet has been disconnecting every hour or so. I had the same problem on Intrepid but I managed to fix it somehow. After disconnecting, it will reconnect after a few seconds.
View 9 Replies View RelatedRecently I've installed Ubuntu 9.10. I have DSL connection so, I wrote all details needed. After trying to connect on it, it automatically disconnects and connect auth connection again. I have worked on 9.04 and older versions and used to work very good, also the internet connection, but not in 9.10.
View 5 Replies View RelatedThis problem is fixed in the upcoming kernel, 2.6.34. You can either wait until Canonical releases the update, or download, build and install the 2.6.34 kernel manually. The instructions to do so are HERE. It's fairly easy.I'm having a problem on Lucid (amd64) with a Linksys WUSB54Gv4 usb wifi adapter. After some time (varies between ~10 mins to a few hours), the connection is lost. However, in my case I can't connect back. It tries to establish the connection, then pops up the dialog asking for the WEP key again. It will do this repeatedly, not ever connecting back.This is basically how the disconnect looks in dmesg:Quote:
[ 2657.920014] phy0 -> rt2500usb_set_device_state: Error - Device failed to ente
r state 1 (-16).
[ 2658.120008] phy0 -> rt2500usb_set_device_state: Error - Device failed to enter state 3 (-16).
[code]....
I've recently downloaded, installed Ubuntu 10.04 (june 5 2010)
As title suggests, this is about my USB wireless adapter Linksys WUSB54G ver.4 periodically failing. Now, the exact problem AND solution was posted on this thread:
[URL]
Essentially, I have to try a new kernel or something. I downloaded the kernel 2.6.34 at http://kernel.org/ which is supposed to solve my networking problem. But above thread suggests building my own kernel somehow [URL] and some of its steps are unfortunately not straightforward as copy-and-paste and i'm afraid i can't go on after trying to mimic command prompts a few times.
I tried referring to other sites, like
[URL]
but their suggested steps aren't exactly the same, or maybe they are really but i'm too dumb to see it.
I think I managed to copy the config file (i hope i chose the right one) and put it to the extracted folder of new kernel I just downloaded, but "Build the linux-image and linux-header .deb files" ?
After upgrade to Lucid I have experienced intermittent wireless disruptions. The wireless just cuts out and reconnects.And I was hoping to continue or follow up on the same thread however with the released version.I tried replacing network manager with wicd and I tried the other driver options both without success.I'm currently using the Broadcom B43 driver, when I tried the Broadcom STA driver wireless would not work. I use the 64 bit OS, and this problem did not appear prior to the upgrade.
View 1 Replies View Related