Im on 9.04 and i upgraded to the latest kernel. Pretty much a default .config for a kernel few things here and there removed. When i boot into the kernel and go to connect to the wifi it shows enable wireless grayed out and enable networking checked.
View 1 Replies
I am writing this using the 2.6.31-17 generic kernel after rebooting and selecting NOT to use the 2.6.31-18 kernel which was just installed. The newer kernel would not recognize/activate my Atheros AR2418 wireless adapter and, when I connected to the ethernet and did updates, there were no hardware drivers available. I haven't needed proprietary drivers since I upgraded to 9.04 and 9.10 works fine with older kernel.
View 1 Replies View RelatedA quick note for other frustrated Ubuntu users out there. I have a D-Link DWA-510 PCI wireless card (RT61) that just stopped working. After wasting hours searching posts and asking for help, I've determined that there's a problem in the latest Kernel to be rolled out.
I have now installed StartUp-Manager, and used it to boot into the old 2.6.31-22 kernel still on the machine and, hey presto, wireless is working again. It seems like the simplest fix by far.
How can I get information similar to proc/net/wireless but for more than just the wireless router I'm connected to. I know there has to be a way because when I'm disconnected from all routers the network manager shows signal strength of all available routers.
View 3 Replies View RelatedI'v tried to uninstall and reinstall wubbi 4 times already. Before the OS even start up it says that it cannot find the wireless kernel and then it boots me up into that start up with the *configuration wizard* and that fails as well and asks me to reboot.How can i get my wireless transfered to Ubuntu without using a flash drive or CD? I thought that Ubuntu would automatically detect my wireless but i see no options as such.
View 2 Replies View Relatedwhat is name of modules in kernel for wireless and lan driver ?
View 1 Replies View RelatedI have problem with my laptop, the last week I update my kenel to 2.6.32-24-generic-pae and in this moment the wireless drive dosen't work.
View 1 Replies View RelatedI was able to successfully install the drivers on the generic kernel, but I seem to be having a problem getting it done on the real time kernel I downloaded via the Ubuntu Software Center. Here's what shows up when I type in 'make' at the command line:
Quote:
/driver/rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.20100 625$ make
make ARCH=i386 CROSS_COMPILE= -C /lib/modules/2.6.31-11-rt/build M=/home/marcoharder/rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.20100 625/driver/rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.20100 625 modules
[Code].....
I just want to enable my wireless network card... how do I do that? It worked perfectly in Jaunty and it also worked when Jaunty was upgraded to Karmic, but in a fresh install of Karmic it is displayed as DISABLED:
sudo lshw | grep network:
*-network:0 DISABLED
I know this is not a bug in any kernel or anything. I now have Karmic on two identical laptops (Fujitsu Siemens AMILO, rt2500pci chipset) with the same kernel (2.6.31-22-generic). Wireless is enabled on one, disabled on the other. This is wearing me out... I am on the verge of buying Windows 7...
I have this weird issue which only appears when I am using 64 bit Ubuntu. Every now and then my laptop seems to go into a kernel panic (system unresponsive, numlock and scrollock lights flash repetitively) only when I am using the broadcom wireless. I can connect to my wireless router and use the internet and local network, but eventually, kablamo, crash, bang, boom. The only way out of the crash is to power off completely. After repowering, the wireless network is fine until the next crash. There does not seem to be a pattern or time period to cause this crash either. I have purged network manager(which I couldn't get to use my wireless) and am using wicd, which allows me to connect wirelessly.
Here is the details of my system:
Dell inspiron 1520
lspci (snipped)
0c:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01)
[code]....
I just upgraded the kernel on my Ubuntu laptop from 2.6.32-24-generic to 2.6.32-25-generic (using the update manager under gnome). After the update, the wireless network controller shows up as UNCLAIMED when I do lshw -C network.When I try to install the driver with the commands sudo modprobe lib80211 sudo insmod wl.ko
i get this error message: insmod: error inserting 'wl.ko': -1 Invalid module format
I have compiled the driver using the 2.6.32-24 kernel. Do I have to re-compile with the new kernel?I'm a unix user, but not a kernel hacker, so I'm wondering if I will run into problems every time I get a kernel update? Or is this problem an exception?
I am having some issues getting the broadcom sta driver installed on Kernels 2.6.36 up through 2.6.38.
Before I continue, I'll list my specs
Release: Xubuntu 10.04.2 LTS (64-Bit)
Wireless Card: Broadcom BCM4328
Kernel: 2.6.38-x (Any version), and 2.6.36 and above
EDIT: Yes! Yes! I got it to work, for those that are having issues, install this packages. Disregard that it says that there is an older version available in a software. The bcmwl-kernel-source for Natty works on Lucid![URL]... Install one of these and check your Hardware Drivers, they will probably say that the Broadcom STA driver is installed but not in use. If you then proceed to restart it should be up and running, this way you can use kernels 2.6.36+ and still use the Broadcom STA driver!
I made a custom kernel for maverick, 2.6.35-27. And I want to get the latest Intel 5300 wireless card drivers working. The wireless works now, but I want to get these installed anyway. I've been on a custom compilation kick for a while, and just been wanting to do everything compiled myself, just to learn a lot. Including putting linux on my WNDR3700 router using DD-WRT. Still doing a lot of customization on that as well.
View 1 Replies View RelatedI upgraded from kernel-2.6.38.6-27.fc15.x86_64 to kernel-2.6.38.7-30.fc15.x86_64. After the upgrade I no longer have a wireless interface in Network Management. I have a broadcom BCM4312, booting the previous kernel solves this problem.
View 9 Replies View RelatedI've only used Linux for about a year or two now and have worked through suspend esume and WPA wireless issues with CentOS and my T61p. However, I'm stumped on this one. why my T61p freezes randomly (happened once while writing this topic) with the caps lock light blinking. I'm wondering if it has something to do with my nVidia driversettings andor using my wireless card and/or switching between home wwireless and work wwired connection.
[Code]...
I wireless network card is Broadcom Corporation BCM431, but is doesn't work after I update kernel from
2.6.29.6-217.2.7 to 2.6.29.6-217.2.8.
Linux localhost.localdomain 2.6.29.6-217.2.7.fc11.x86_64 #1 SMP Fri Aug 14 20:53:08 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux
Everything worked fine on kernel 2.6.33-6.But since the update to kernel 2.6.33-8, not always but nearly everytime I resume from suspend, my wireless network is disabled.When I right click the tray Icon the "Enable Networking" box is unticked and greyed out.Only a reboot brings networking back
View 14 Replies View RelatedA friend who switched ISP's gave me his old Linksys WRT54-G wireless router. I went through the installation procedure and had a wireless connection up and running - smiley face. I had security set up for WPA, and decided to upgrade it to WPA2. Another smiley face. When I went to connect (had already done so successfully), I noticed it referred to my wireless as Linksys - I was expecting to see the SSID. So I started playing around in Network Manager and now I have things all effed up.
Don't know exactly what I did, but now I have no wireless. So I ran a few commands (lshw -C network, iwconfig, ifconfig, and iwlist scan), and looking at the results I see what appear to be inconsistencies in the output. I've posted them below, and make the following observations:
1. Under the lshw it refers to my wireless connection logical name as wmaster0, and has the correct MAC address, etc.
2. Under the iwconfig it says, 'wmaster0 no wireless extensions', but then refers to wlan0 as the wireless connection (although it does not seem to be running).
3. Under ifconfig I see both a wlan0 and a wlan0:avahi. The wlan0 has no IP, the wlan0:avahi does, but it is incorrect.
[Code]...
Ok, so I am needing some drivers and I've been googling like hell to find em, however, I can never seem to find any. My adapter model is F6D6050v1.
PS: when I try sudo ndisgtk it comes up with command not found.
I'm using a Packard Bell Easynote Tn36 laptop, and I'm having trouble with Ubuntu 10.10 and the wireless network card, (probably because of lack of driver). I.e. it is disabled.
How can I enable it?
I input this code:
And here is the output:
I just upgraded to natty last night, and everything is working fine except for the network manager. I can enable and configure the wireless card via bash, but the network manager widget will not manage the wireless card.
When I first boot up, the "Enable wireless" check box is greyed out. After I enable the card via the terminal, the "Enable wireless" check box becomes ungreyed, but every time I click it, it instantly unchecks itself. I feel like Currly from the Three Stoogies. Check, uncheck, Check, uncheck.. "Slaps face repeatedly."
I have Packard Bell easynote tn36 and I used to use ubuntu 10.10 and then when I upgrad it to ubuntu 11.04 the wireless doesn't work (disable) and I can't press the botton of Enable wireless.
View 9 Replies View RelatedVirtualbox, is great, except that I have no wireless networking or USB support. Problem one, is USB support. As far as I know there is a personal free use version of Virtualbox that includes USB support, however I can't find this copy to download it. Any ideas where I can find it? Second problem, I have an integrated wireless networking card in my laptop, that Ubuntu recognizes with no problems, but Virtualbox can't even "see" the device. I found a tutorial that addresses this know issues with wireless and Virtualbox, but I don't understand the instructions
[URL]
Quote:
Wireless Networking Setting up a normal bridged network generally doesn't work if you're bridging from a wireless card to VirtualBox. A simple script that utilises the parprouted tool will allow your VM full access to the wireless network. You will require parprouted to do this: sudo apt-get install parproutedNext, using your favorite text editor, create and edit the script, for example:
sudo nano /etc/network/if-up.d/vbox_networkThen, enter the script (replacing $USER with your username (or whoever you intend to run virtualbox as)). Replace wlan0 with the name of your wireless interface. Use an available IP address on your network for tap0 (I have used 192.168.1.100 in this case):
sysctl net.ipv4.ip_forward=1
VBoxTunctl -b -u $USER
ip link set tap0 up
ip addr add 192.168.1.100/24 dev tap0
parprouted wlan0 tap0Finally, make sure the new file is executable by root: sudo chmod 700 /etc/network/if-up.d/vbox_networkNow your networking script is installed, the virtual interface tap0 will be available on boot for VirtualBox. Rather than reboot, let's just run the script now:
sudo /etc/network/if-up.d/vbox_networkThe final thing to do is tell VirtualBox to use the new virtual device tap0. Open VirtualBox, highlight a VM and click settings. Now choose the network option and select Host Interface on the 'attached to' drop down menu.
In the Interface Name text box, enter: tap0 Click ok and start your VM. The VM should now behave as though it was another physical machine on your network!! For more information on the process up to this point, please visit Bridged Networking with VirtualBox on Linux Hosts Using DHCP in the Guest VM It was possible to get DHCP to work on the guest virtual machine. Instructions were taken from here. Because parprouted does not relay multicast, we need to use an additional helper daemon to manage this. I tried dhcp-helper and bcrelay, and had the most success with bcrelay.
Use it as follows:
sudo apt-get install bcrelay
sudo bcrelay -i tap0 -o wlan0At this point, my /etc/network/if-up.d/vbox_network is as follows:
#!/bin/sh
sysctl net.ipv4.ip_forward=1
[code]....
bcrelay -i tap0 -o wlan0 &It seems that I have to start the script by hand after boot. Other than that, host networking now seems to work fine (this issue should be solved by adding the "#!/bin/sh" line just at the beginning of the script.
My mother has Windows Vista and i have linux ubuntu. She has a special verizon card that she inserts into her laptop for internet. My computer also has an internal wireless card, but the signal here is very poor. Supposedly, among windows computers, I would be able to get a flashdrive, and with a little program uploaded from my moms computer, set things up using the flashdrive on my computer to share the internet that she pays good money for =/ However, it wont work with ubuntu, which isnt in the windows inner circle. When I open the executable file with WINE it says that it cant run wireless network setup "on this version of windows". lawl. I was wondering, is there any way around that? Is there anyway to network with my mothers internet?
View 2 Replies View RelatedI've had my wireless networking (on an Acer Aspire laptop) working perfectly well for at least six months.Now, quite suddenly, after a reboot I get the message from wicd, "No wireless networks found". I probably was running a week or so before that without needing a reboot. Windows wireless is fine (I'm using it to send this post).In addition, my sound stopped working and I see a fleeting message to the effect that the sound system is reverting from analog to digital.I'm running Kubuntu 9.10. My guess is that something in a recent round of updates knocked me out of the box. How can I proceed to set things aright?
View 1 Replies View RelatedMy laptop is an Amilo a1650 on which I've very recently installed Ubuntu 9.10. It's worked out fine so far, except that I can't get the wireless card to work. It's an internal Broadcom BCM4318. Where do I start with configuring it?
View 1 Replies View RelatedI have a desktop with a printer attached on a wireless link.I have a laptop where I want to print from. The problem is the wireless link comes up only after I log on to the desktop.I would prefer the wireless link (and cups) to be up with out having to log on at the desktop.
How would the run level be changed?
I have a compaq c784tu and it was shitty with xp. Vista is quite crap, so i turned over to ubuntu 10.4. The configuration of the laptop is: 1.73 GHz Intel Pentium Dual Core Processor T2370 with 1-MB L2 Cache, 533 MHz FSB featuring Intel Mobile 945GML Express Chipset Motherboard, 2-GB PC2-5300 DDR2 667 MHz SDRAM (Maximum 4-GB in 2 slots), a 160-GB SATA 5400 rpm Hard Disk Drive and 8x Super Multi Double Layer (8.5 GB) Slot-in DVD Writer.Everything worked like a charm and I was able to connect to the internet through a public wifi network. However, I came home this week to my mothers house, where they have a dsl-router to connect to the internet whih uses bridge mode pppoe. I tried to connect to the internet through it, and it initially couldnt. However, I got around that by doing a clean install of ubuntu. I was able to then connect to the internet using "sudo pppoeconf" and "sudo pon dsl-provider"One night the network manager app on the top left disappeared and would not come on. I figured I had fried my wifi adapter, however, lspci -v confirmed its presence.Further, "system>admn>system testing" detected the adapter aswell. I tried the iwconfig command in the terminal the result was:
lo no wireless extensions
eth0 no wireless extensions
wlan0 IEEE 802.11bg ESSIDff/any
[code].....
My wireless can connect to my router without a problem, but in order to do so (after boot) I must first disable networking in the Notification Area and then re-enable it. I don't mind it too much, but when other people use my computer, it's made painfully obvious to me, that this was never an issue with Windows 7 (as much as I despise MS).
View 9 Replies View RelatedI need straight forward directions on how to do this. I installed samba on ubuntu and I shared a number of ubuntu files. No luck.Xp can't see ubuntu and the reverse is also true. My searches just end up off on some tangents. Example, researching samba - I get the entire manual on samba - can't find the specifics I need within that document.
View 2 Replies View Related
