Ubuntu Networking :: Lucid Won't Detect Laptop Ethernet Card?
Nov 15, 2010
so, when i first got my laptop it came with vista and the ethernet worked fine, then when I decided to install Karmic about 9 months ago it still worked fine. After a while the update for lucid came out so I upgraded to that and then the ethernet started getting buggy. It would only work about half the time that i wanted it too and the other half of the time it would just stare at me and not move anywhere. So along with a couple other bugs I decided to format my harddrive and downgrade back to karmic and await the 10.10 release. unfortunatly my ethernet woes carried with me and they still would only show up on occasion. then about half way through my time with karmic round 2 it stopped altogether, and with the upgrade back to lucid it hasn't seemed to solve itself.
I ran through ifconfig -a, lspci and sudo ifup -a but they all tell me that the device doesn't exist.
View 6 Replies
ADVERTISEMENT
Jul 19, 2010
I'm on an HP Pavillion dv4-1125nr with a Broadcom BCM 4312 network card.
I only have Ubuntu 10.04 installed on this computer.
ifconfig reports:
Code:
eth0 Link encap:Ethernet HWaddr 00:1e:ec:b5:b4:85
inet addr:192.168.0.5 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::21e:ecff:feb5:b485/64 Scope:Link
[Code]....
It isn't even detecting the wireless card, and the network manager will only let me connect to wired networks (I'm connected to my router via ethernet cable right now).
I've pressed the LED killswitch but it does nothing (doesn't change from orange to blue nor does it have any noticeable effect on the network manager or the reports of the above 2 commands).
View 2 Replies
View Related
Aug 17, 2010
i install devian squeeze with the netinstall iso, all work fine except for the auto-detect of my ethernet card.i have a mother asrock p4i45gv with an onboard ethernet card realtek rtl8139/810x family fast ethernet NIC.i try everithing, the ifconfig shows only lo, but ifconfig -a shows a eth0 any ideas?
View 12 Replies
View Related
Jun 21, 2009
I installed the OpenSUSE 11 on my IBM T43 laptop. After installation finish I found the Yast can't detect the integrated ethernet cardBroadcomCorporationNetXtremeBCM5751MGigabitEthernet PCI Express(rev 11).
View 5 Replies
View Related
Dec 19, 2010
I am trying to install Debian Lenny (64 bit) on my brand new Toshiba laptop (intel i3, 3 GB RAM) and for some reason the installer cannot detect the ethernet card. This is the error message I get:"No Ethernet card was detected. If you know the name of the driver needed by your Ethernet card, you can select it from the list."And then there's a list which is quite long -- and I cannot replicate it here. But I want to know why the installer cannot find the ethernet card on its own or find the appropriate driver. In any case how can I fix this problem?
View 14 Replies
View Related
Jun 15, 2011
While installing my redhat distro in VMware 6, its giving an error message that ethernet will be disconnected.
View 1 Replies
View Related
Aug 31, 2010
Since I have upgraded to Ubuntu 10.04 Lucid Lynx, my second graphics card isn't detected by X server. When I do an lspci I get both listed though. I am using NVidia's driver v195.36.24
View 1 Replies
View Related
Sep 10, 2010
I own an EeePC 701; right now I'm giving 10.04.1 a test run on it, using a live usb.
The EeePC has an Atheros wireless card, but live Lucid doesn't detect it. Here's the output from a ifconfig command:
Code:
Will the card be detected by a properly-installed Lucid? Is there some package I need to install so I can use wireless? Or should I steer clear of installing Lucid on my EeePC?
View 4 Replies
View Related
Jun 14, 2010
i have installed red hat 5.1 on my dell inspiron 1525 laptop.It is not detecting any ethernet card.driver is marvel yukon 88E8040So far i found this package to be installed kmod-sk98lin-PAE-10.70.7.3-2.el5.elrepo.i686.rpm but it is showing me the dependencies problems..
View 4 Replies
View Related
Apr 20, 2010
I am using fedora core 2. I used the oldest version of fedora just because im running only 1 system, my specification is: HP compaq PC,pentuim4, 512mb memory, 40gig hdd, Intel board. I have two units same spec..windows xp and the other one is fedora 2. The windows xp normally detect the lan card, but when I try to fedora2, I try to active it and seems no lan card detecting,. How to detect broadcom nextreme gigabit ethernet to my fedora 2 OS???
View 7 Replies
View Related
Jul 2, 2011
I've got Puppy Linux on a USB key, and yesterday, while I was on the internet with it, it hanged. I didn't know what to do, and I rebooted from the button (I now know what to do ). The problem is that, after rebooting, Puppy doesn't recognise the router. I've tried to apply the drivers that are on Puppy, but there aren't any compatible.
My router is a Xavi 7968 and my Network Card is:
NIC Fast Ethernet PCI Familia RTL 8139 from Realtek
(On Realtek's website, there isn't any driver linux-compatible)
View 7 Replies
View Related
Dec 4, 2010
Just installed Fedora 14 from the Live CD i686 on my Dell Inspiron 1521. I can't connect to the SpeedTouch 585 on either wireless broadcom card or the wired Ethernet card.
I can connect to it from the same Laptop on the Vista which is on dual boot on the same laptop.
Further confusing is that I ran Fedora 14 and connected to another SpeedTouch today.
Already checked the Channel on the wireless nic and it's on the same one as the SpeedTouch.
View 6 Replies
View Related
Aug 13, 2010
I am using Ubuntu 10.04 Lucid and VMware 2.0 server. I have a an XP virtual machine that is needed for work. When I am at home and I place my cat 5 cable to my cisco catalyst switch, my XP VM recognizes the ethernet card on my laptop and bridges fine with ubuntu and works fine and I can get to my network. When I take my laptop to work and I go to a site and I plug it into a World Wide Packet 311 management port on the switch, my XP Virtual Machine does not see the network no matter what setting I set it too(100 full, 10 full, 10 half and etc). It simply says that the network card is disconnect. Ubuntu see the network fine and I can ping and talk to the network without any issues but the VM does not.
View 2 Replies
View Related
Sep 11, 2010
I am trying to get this laptop`s wireless to connect to my router or any wireless connection. It does not have an ethernet port,so it has been tough.I have been reading everything i can,but cant get it to work.Maybe I need a different wireless card or a usb adapter.The one I have is a Texas Intruments acx100.Can anyone tell me if this should work.I have ndiswrapper installed and the windows driver for it but still nothing.
View 4 Replies
View Related
Jul 26, 2011
I have one of these nifty Atom based "net-top" boxes that has built in wireless N and gigabit ethernet. the problem I have is that even when the ethernet cable is plugged in Ubuntu seems to be defaulting to use the wireless connection. This is a problem since in some areas of the house where I have a wired connection the wireless signal is pretty weak and so the ethernet traffic becomes spotty.
is there a setting somewhere where I can force ubuntu to prefer the wired over wireless no matter what, or to disable the wireless when the ethernet is plugged in?
View 2 Replies
View Related
Jan 10, 2010
Just like the title said it won't detect my wireless card. Anybody know what's wrong with it?
View 9 Replies
View Related
Mar 29, 2010
I have ASUS Laptop A6Rseries was running XP untill I installed Linux 9.10. Now i am having problem connecting to my wireless network. I am using Belkin router what works fine with XP, Vista and Windovs 7. Here is some information what I found
lspci
00:00.0 Host bridge: ATI Technologies Inc Device 5a31 (rev 01)
00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80)
[code]....
View 2 Replies
View Related
Jun 6, 2010
I'm trying to set up a shared Internet connection that had been broken by a previous update, I believe. Eth0 is connected to the Internet, whereas eth2 should be the connection going to my Roku set-top box. Under the nm-applet icon, an entry exists for "Auto eth0" for the first card, but there is nothing under the second card except "disconnected". How do I make a connection entry under my eth2 card so that I can share my Internet connection with my Roku box?
View 6 Replies
View Related
Dec 3, 2010
I have brought a new DELL INSPIRON 1410. I installed ubuntu 10.04 but my ethernet card is not getting detected where as in windows 7 is working..
View 2 Replies
View Related
Jan 10, 2011
Running Ubuntu 10.04. Networking won't work at all. Used to work flawlessly. Problem is not hardware, because booting windows (vista) on the same machine I can still use networking.
Little story: I Was going into a short trip, then I put my computer to sleep (as usual). Trip took longer than expected and, when I came back, the notebook battery was dead. Charged it, booted the notebook (Dell Inspiron 1525) and now its network won't work at all. After reboot it even ran a filesystem scan, but problem wasn't fixed. The icon on 'taskbar' only says "networking disabled". The ethernet lights won't even light up when I connect a ethernet cable and it won't see any wifi networks. I've tried to fiddle with that little switch which would turn the wifi on and off, but all it seems to do is turn the Bluetooth on and off, as shown by the little Bluetooth icon on 'taskbar' (I've not tested bluetooth, though). I've also tried to plug a external wifi dongle but ubuntu won't even try to install it.
what's happening or what could I do to get my network working? Is there some 'magic' I can type into a terminal window to make this work?
View 2 Replies
View Related
Feb 8, 2011
I am basically wanting to use my Ubuntu 10.10 computer as a router. Note: Before you say just get a router please note that I am poor/cheap. I have two ethernet connections and one wireless connection on my netbook. I want to share the internet connection that is going into one of the ethernet cards through the other ethernet card and the wireless card.
DSL-->1sr Eth --> 2nd Eth (currently works)
DSL-->1sr Eth --> Wireless Card (Adhoc) <--(connects with limited connectivity AKA no internet)
The 2nd Ethernet card already has working internet, but when I connect to the Wireless card (through an Adhoc network), it cannot get an IP (I believe).
View 2 Replies
View Related
Apr 24, 2010
can one ethernet card support multiple ip address? but i think it's very dangerous. if bad guy take many ip, other people can't get ip. "does one ethernet card take multiple real ip or multiple virtual ip(one real ip)?" if it takes multiple real ip, then how it works good?..
View 7 Replies
View Related
Nov 22, 2010
I am facing problem with onboard lan card. i think its not detecting. when i type ifconfig command it shows below details
I have installed red hat. but not able to give ip.
View 3 Replies
View Related
May 6, 2010
I own a D-Link DI-604 wired router and I've started getting some issues after Ubuntu 9.10 to 10.04 upgrade(Ubuntu 9.04 used to work OK!). The problem is that Ubuntu recognizes all my ethernet cards (see below), but I can only connect to the internet through eth1 not eth0 (which is my Windows default). If I try to plug the cable in eth0 nothing happens (at least not in Ubuntu 10.04 and 9.10).
Code:
lucas@lucas-desktop:~$ sudo lshw -C network
[sudo] password for lucas:
*-network:0
description: Ethernet interface
[code].....
View 9 Replies
View Related
May 20, 2010
I have just installed a generic PCI ethernet card into a fairly low powered system (Celeron 766MHZ, 512mb Ram, 40 Gb HDD, Generic sound and video). The card came with no drivers. I have since installed Ubuntu 9.10, and up to a point everything is fine and looks great. However when I connect an ethernet cable up to the PCI card (in the hope of connecting with the Internet), nothing happens. I am thinking that I need Ubuntu drivers for the PCI card ? or does Ubuntu 9.10 come with drivers and I need to go into the 'engine room' to sort it all out ?
View 1 Replies
View Related
Jul 2, 2010
I've had way too many problems with my network card under linux and I'm looking to buy a new one because the money is worth the lack of headaches. My project: I'm breathing new life into my old, old pentium 4 computer by running Kubuntu Server on it and using it as a little samba filedump.
So I don't want to spend a lot on an ethernet card -- this computer is no prize. I just want the cheapest, most out-of-the-box-compatible-with-no-configuration card I can buy.
I started on Newegg (sorted by price: [URL]....CE&PageSize=20 ), and I've heard that cards based on the RealTek 8129/8139 chip may be compatible/cheap but I can't seem to find out ahead of time what chip the cards are based on.
View 6 Replies
View Related
Jul 18, 2010
I've set up 10.04 Server so that I could install directly to a command line, due to the fact that Desktop was crashing during the install every time. The installation goes fine, except for the networking portion. DHCP fails every time I try it. So I set up a static IP as an alternative. Once installation completes, none of the network-oriented tools (ping, telnet) work. I've tried pinging my router and I get 'Destination Host Unknown'. This is true if I change to a DHCP oriented setup as well.
The router sees that the machine is there, as indicated by the slowly blinking connection light meaning that it's hooked up to *something* but there's no activity. Also, networking did work within Windows before I nuked it, so I know it has the ability to operate correctly. I'm at a loss, mostly due to my own newness and ignorance of how to start tackling this within this environment.
View 9 Replies
View Related
May 9, 2011
The on-board NIC on my machine died this morning, so I've just gone out and bought a replacement PCI card. The card has been recognised by Karmic, but it's not working. /var/log/messages says:
Code:
May 9 11:21:58 ian-desktop kernel: [ 2.082324] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
May 9 11:21:58 ian-desktop kernel: [ 2.082334] r8169 0000:04:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[Code]....
how I install the appropriate driver (noting that I have to sneakernet files across via usb stick), or any other diagnostics I should try?
View 2 Replies
View Related
Feb 15, 2010
My ISP finished some 'upgrades' on its infrastructure. The result is that I am having great difficulty in connecting to the internet.
I have 3 operating systems on my box - XP, Fedora 8 and Feota 12.
I connect using an ethernet card, using dhcp. In fedora 12, the ethernet card is controlled be networkmanager. After the ISP completed their upgrades, I was not able to connect. I tried to connect manually using
Code:
There was an error message -
Code:
I read the advice here: [url], and removed all but the important lines.
But even after that neither ifup eth0 or dhclient eth0 works.
In fedora 8, the ethernet card is activated by ifup eth0 in /etc/rc.local. I was able to connect on a couple of occasions, but that too stopped working. I tried both ifup eth0, dhclient eth0, and tried to use the gui( which fires the dhclient command), but none worked.
When I use windows, it takes about 2 minutes to get an ip (earlier it was immediate). Sometimes that doesnt work and I have to click on "repair" whereupon it starts working.
View 1 Replies
View Related
Sep 2, 2010
Tell me how to configure my Ethernet card to work. My pc only works wirelessly. I don't know what kind of Ethernet card is installed. I have Ubuntu 10.4 on a dell pc 1ghz, 20ghd, 512mb.
View 2 Replies
View Related
