I installed the OpenSUSE 11 on my IBM T43 laptop. After installation finish I found the Yast can't detect the integrated ethernet cardBroadcomCorporationNetXtremeBCM5751MGigabitEthernet PCI Express(rev 11).
View 5 RepliesI have a strange problem. An old PC is my home server. On the PC I had in the long past 2 NICs. For the last year or so, I had only one NIC installed, a Compex with 8139too module which run just fine. After the upgrade to 11.4, 32bit of course, with zypper dup, I saw that I had no internet and no network connection to the server. So, I logged on the server and found that rcnetwork could not start the eth0 and eth3(!). OK, a mistake I thought. Enter Yast and solve it. Unfortunately, yast reports 2 cards! I removed all of them, rebooted but nothing. lspci reports 2 cards, while I have NONE installed on the motherboard!hwinfo --netcard the same! yast the same! So, the OS "knows" that I have 2 NICs, while I definitely have none!
Checked if /etc/udev/rules.d/70- had any left data from the past, but the file was empty. Checked the /etc/sysconfig/network/scripts nothing again.In principle, the openSUSE 11.4 believes that I have 2 cards (and with wrong MACs, obviously) and I cannot make it rescan the PCI bus to find that I have nothing! I am sure that some garbages are left somewhere but I don't know where to look at. it is very critical to have that server but on-line and in my LAN.
i install devian squeeze with the netinstall iso, all work fine except for the auto-detect of my ethernet card.i have a mother asrock p4i45gv with an onboard ethernet card realtek rtl8139/810x family fast ethernet NIC.i try everithing, the ifconfig shows only lo, but ifconfig -a shows a eth0 any ideas?
View 12 Replies View RelatedI have a hp zd 7000, i really like this laptop, the onboard ethernet will not work at all. i purchased a dynex wired ethernet pcmcia card to get on the internet with. i have had no luck getting on the internet with it it will light up so i am getting power but no transmitting light works at all i have three net work cards listed in the system. one is the wireless. and the other two are the wired eth0 is the onboard and eth2 is the dynex what can i do next to determine the problem i do not use the wireless at all.
View 1 Replies View RelatedI am trying to install Debian Lenny (64 bit) on my brand new Toshiba laptop (intel i3, 3 GB RAM) and for some reason the installer cannot detect the ethernet card. This is the error message I get:"No Ethernet card was detected. If you know the name of the driver needed by your Ethernet card, you can select it from the list."And then there's a list which is quite long -- and I cannot replicate it here. But I want to know why the installer cannot find the ethernet card on its own or find the appropriate driver. In any case how can I fix this problem?
View 14 Replies View Relatedso, when i first got my laptop it came with vista and the ethernet worked fine, then when I decided to install Karmic about 9 months ago it still worked fine. After a while the update for lucid came out so I upgraded to that and then the ethernet started getting buggy. It would only work about half the time that i wanted it too and the other half of the time it would just stare at me and not move anywhere. So along with a couple other bugs I decided to format my harddrive and downgrade back to karmic and await the 10.10 release. unfortunatly my ethernet woes carried with me and they still would only show up on occasion. then about half way through my time with karmic round 2 it stopped altogether, and with the upgrade back to lucid it hasn't seemed to solve itself.
I ran through ifconfig -a, lspci and sudo ifup -a but they all tell me that the device doesn't exist.
While installing my redhat distro in VMware 6, its giving an error message that ethernet will be disconnected.
View 1 Replies View RelatedI installed 10.3 (after buying it a couple of years ago and letting sit on the shelf) and can't get it to configure my ethernet connection or my wireless card. Yast doesn't include a list of available cards, and the error I get in installation-network setup is that the kernel isn't present. The machine I'm installing this on is a Lenovo, in which there isn't a discrete ethernet card (it's in the motherboard), but my wireless card (a Cisco LINKSYS 802.11G) is a discrete card. Because I'm divorcing Microsoft for a number of valid reasons, I don't have Windows available on that box.
View 4 Replies View Relatedi have installed openSUSE 11.2 on a dell dimension 2400. My Ethernet card wasn't working, so i am using a wireless interface, but it doesn't work either. It worked on a dell dimension 4400, but when it gets to the activate network my system freezes. Should i re-install my system, or should i post this under the hardware category.
View 9 Replies View RelatedI have a dual boot system (Suse 10.0 and Windows XP Pro) in my notebook. My notebook is toshiba m358, which has a Marvell Yukon Gigabit Ethernet Network Card (Marvell 88E8072) on it. My problem is this: in Windows XP Pro, the network card works well, but in openSUSE, the light on the network card does not turn on. I believe that there is no driver for the network card. I have tried several ways to solve this problem:
1. Download Marvell 88E8072's driver from "[URL]", whose name is "install_v10.85.3.3.tar.bz2", and then install it with following commands:
Code:
# tar xfvj install_v10.85.3.3.tar.bz2
# cd DriverInstall
# ./install.sh .....
Code:
# modprobe sk98lin
# WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/.
After I reboot the openSUSE, the light of network card is still off.
2. Follow "[URL]" to configure the Marvell 88E8072. It also does not work.
I've added a 2nd ethernet network card into my linux box. After I installed it the box recognized the new card and mapped it to eth1, as I expect. I then configured the addresses and routing for my eth0 and eth1 interface. Since then I had shutdown my box.When I next started my linux box up only eth0 was present.`ifconfig -a` only displays eth0, but `lspci` lists both cards. How can i permanently map the new pci card to eth1?
Code:
scattaneo@unthread:~$ ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:1a:a0:8c:61:49
inet addr:192.168.2.108 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: 2002:c0a8:6414:1234:21a:a0ff:fe8c:6149/64 Scope:Global
[code]....
I just installed x64 Fedora, and as the title says, NM fails to detect my WiFi card. It's an Encore ENLWI-N with a RaLink RT2800 chipset. The card does show up when I run lspci, although iwconfig yields nothing.Not sure if this helps, but when Ias running Karmic Koala, Ubuntu detected the card immediately and required no configuration
View 2 Replies View Relatedopensuse 11.3 cannot detect my wirless card.
View 9 Replies View RelatedHow to install Ethernet network card module (driver) for the Notebook Toshiba QOSMIO X500-121 64-bit on Lenny?
View 1 Replies View RelatedI am having a situation where I couldn't connect to Internet through wireless and LAN cable. I have done ifconfig, it only shows me "lo" info. May I know how can I bring up the LAN and wireless?
View 2 Replies View RelatedI'm on opensuse 11.4 (11.3 won't work with my monitor).
My computer gets internet through wireless and I want to share that internet through its ethernet port. So far I've tried using Knetworkmanager to create a network bridge between my wireless and wired connections. I created a new wired connection and shared it using the ip address settings. I was able to get both connections active, but the device hooked up via ethernet had no internet connectivity.
I also tried this command:
echo 1 > /proc/sys/net/ipv4/ip_forward
but another test resulted in the same fashion (no internet on wired). I believe anything I add to /proc should have an immediate effect, correct?
I often use an Ethernet cable to connect my computer to another computer for various purposes. But when I do that, I cannot use the internet even though I'm still connected to a WiFi access point. I'm presuming that's because openSUSE is trying to reach the internet through the Ethernet cable, which has precedence over WiFi.Is there a way to enable internet usage via WiFi while I'm connected to another computer over Ethernet?
View 9 Replies View RelatedI am basically wanting to use my Ubuntu 10.10 computer as a router. Note: Before you say just get a router please note that I am poor/cheap. I have two ethernet connections and one wireless connection on my netbook. I want to share the internet connection that is going into one of the ethernet cards through the other ethernet card and the wireless card.
DSL-->1sr Eth --> 2nd Eth (currently works)
DSL-->1sr Eth --> Wireless Card (Adhoc) <--(connects with limited connectivity AKA no internet)
The 2nd Ethernet card already has working internet, but when I connect to the Wireless card (through an Adhoc network), it cannot get an IP (I believe).
I have just switched over from Ubuntu. My PC with Ubuntu connected to the ethernet fine, but now the internet is not found at all. Can someone tell me what sort of things I need to do to get my internet up?
View 2 Replies View RelatedI was trying to activate my wireless connection .... in turn did something that triggered eth0 no-carrier when "ifstatus eth0"
View 2 Replies View RelatedToday I switched from Ubuntu to OpenSuse. But I can't setup my Ethernet connection.I have 2 PCs connected with a crossover cable, one with Ubuntu, the other with OpenSuse 11.3. Lights are on in both NICs.
View 9 Replies View RelatedI am using Sony vaio E series laptop. Previously, I was using my E63 nokia phone as modem for internet connection and i have installed K-internet in my Opensuse OS, and configured wvdial.conf as follows:
[Dialer Defaults]
Init1=ATZ
Init2=ATQ V1 E1 S0=0 &C1 &D2 + FCLASS=0
Init3=AT + CGDCONT=1, "IP","bsnlnet","",0,0
Baud=4608000
Modem Type= Analog Modem
[Code]....
But now, I have Reliance Brodband Connection through LAN. when I am Pluggin in my LAN cable in my laptop YAST Network Configuration Showing Marvell Ethrtnrt is not Configured, When i am going to configured that part it's showning me no Enther net present or Configured By ny Hardware Is detecting ethernet. So, I have concluded that it might be the problem with my wvdial.conf. Also, additional information are as follows:- S- Open suse 64bit, Version- 11.2, cause I cannot Connect to my Internet now? What should I do to have this Problem Fixed?
I've connected my openSUSE laptop with a Windows XP computer using an Ethernet cable that supports two-way traffic.
LAN settings on Windows XP
IP address: 192.168.5.1
Netmask: 255.255.255.0
Gateway and first DNS server: 192.168.5.2
LAN settings on openSUSE
I've been searching for a couple of hours and have not found any threads that solve my situation... hope I'm not repeating something here.
Setup: Notebook with openSUSE 11.2 using KDE 4. Using Network Manager to manage network connection (although I've tried configuring this using ifup as well with no luck).
I need to be able to connect to client networks via a network cable (Ethernet) and connect to the internet via my MiFi 2200 Mobile WiFi. Both cards/connections are active with the following:
I have no problem mounting drives from the client's network. But, can not reach the internet. If I disconnect the ethernet cable, the browser will immediately connect to the internet and load web pages.
I'm assuming the ethernet connection is taking precedence over the wireless connection?
I can't imagine that there is not a way to set this up. If Windows can do it, I'm sure openSUSE can!
system:
destop
openSUSE 11.4 KDE
single wired network connection
running as a headless server
upgrade from 11.1
Problem: I had a bunch network services running under 11.1 with KDE. Now after upgrade to 11.4 full network functionality is broken. I was using ifup but now is broken. Between ifup and NetworkManager I can demonstrate the full required range of functionality but not all at the same time (the union of functionality of each provides the full required functionality, but not individually). WOL does work in all cases.
With 'ifup', it seems that everything is 'working' as before, but services are broken when accessed from outside. eth0 up and fuctioning with statically assigned IP. Outgoing connections seem to work - I can browse the web. But trying to access services from outside is broken. VNC is rejected. Connecting to SMB shares reports login error. TFTP doesn't respond. SSH connection is rejected.
Although sometimes it will get in a state that everything except VNC works (connects but then is dropped upon login with "Error while waiting for server message") but I can't consistently reproduce this state other than it seems to happen after some extended period of time.
I have verified the firewall is off and apparmour is off.
On the other hand, everything works with 'NetManager' (both KDE and Plasmoid) with no other changes. The problem here is that it does not seem possible to set a static IP address - eth0 doesn't show up in the list of wired interfaces to be able to select and edit. That's problem 1 - I need a static IP. (I suppose I could reserve an address at the DHCP server, but a static IP works 100% to get the right address). The other problem is that neither NetManager starts at boot and only start _after_ login at the console - that won't work as I never log in at the console. (I suppose I could set it up to login automatically into a console or something but I would rather not)
Just installed Fedora 14 from the Live CD i686 on my Dell Inspiron 1521. I can't connect to the SpeedTouch 585 on either wireless broadcom card or the wired Ethernet card.
I can connect to it from the same Laptop on the Vista which is on dual boot on the same laptop.
Further confusing is that I ran Fedora 14 and connected to another SpeedTouch today.
Already checked the Channel on the wireless nic and it's on the same one as the SpeedTouch.
How can I enable the network with Networkmanager WIHTOUT logging in in OpenSuse 11.2?
If I define a connection for ethernet the System connection is greyed out. I want to use Networkmanager because I have also wireless connections...
My WiFi can connect to internet without any problem, until I plug my ethernet cable ...then I lose internet.
So the question is : how do I configure my ip/dns and stuff to still have internet when I'm plugged by cable at the same time! it was working on windows ;-)
I'm currently using SuSE 11.4 and after running the full online updates and restarting the machine as YAST suggested, I no longer have eth0/eth1 available.
I'm clueless about what to do since I'm kinda new to Linux and at the moment, I'm trying out all the distros before making a full commitment to anyone. So far, Ubuntu has been trouble-free from day one, but I'm willing to give this distro (opensuse) some slack.
Just installed Suse 11.4 Kde build. Using 64 bit ECS A780GM-A Ultra Mobo, 4 gigs ram, Athlon 7550 CPU, I am unable to detect my Verizon broadband MIFI 2200 with this new OS, have used Ubuntu in the past. Plugged in USB cable for modem into different ports, still does not work,
View 1 Replies View Related