have a dell Inspiron 1501 with ubuntu 10.0.4 I want to rename my wireless card from eth1 to wlan0 as I use conkyrc and it will not read my wireless strength or my ssid cuz it thinks it's a ethernet card and not wireless card. I know this for a fact because peppermint os my wireless card was wlan0 and it worked just fine.
View 1 RepliesA friend who switched ISP's gave me his old Linksys WRT54-G wireless router. I went through the installation procedure and had a wireless connection up and running - smiley face. I had security set up for WPA, and decided to upgrade it to WPA2. Another smiley face. When I went to connect (had already done so successfully), I noticed it referred to my wireless as Linksys - I was expecting to see the SSID. So I started playing around in Network Manager and now I have things all effed up.
Don't know exactly what I did, but now I have no wireless. So I ran a few commands (lshw -C network, iwconfig, ifconfig, and iwlist scan), and looking at the results I see what appear to be inconsistencies in the output. I've posted them below, and make the following observations:
1. Under the lshw it refers to my wireless connection logical name as wmaster0, and has the correct MAC address, etc.
2. Under the iwconfig it says, 'wmaster0 no wireless extensions', but then refers to wlan0 as the wireless connection (although it does not seem to be running).
3. Under ifconfig I see both a wlan0 and a wlan0:avahi. The wlan0 has no IP, the wlan0:avahi does, but it is incorrect.
[Code]...
trying to connect wireless on wlan0 intel pro wireless 4965 AG or AGN
View 1 Replies View RelatedAfter 3 days and 2 gallons of sweat and 9 billion forums read I give up, I cannot figure out why Ubuntu 9.10 does not read my wireless card. I have a Lenovo G555, I followed most of the instructions the forums provided online such as ndiswrapper and finding the inf. file within windows, copying it to your usb and than putting it into ubuntu to later use windows wireless drivers to install the driver just to run into a bcmwl6 Invalid Driver! I tried to use terminal with no sucess. Can someone just please give the straight forward how to make this work answer.
View 1 Replies View RelatedI have managed to get everything MOST of the way setup...Come to find out though that I cant get conky to function 100% due to my wireless card being named eth3 instead of wlan0...I can get everything to work except for the signal strength, since ubuntu thinks its an ethernet cared. (although it show up as wireless connection in the network interface on the top right of ubuntu control bar). It's not a BIG deal but I was wondering if anyone had a fix or work around for this. BTW it is a Broad 4311 using Broad STA drivers if that makes any difference at all...
View 1 Replies View Relatedhaving trouble with my asus 1000 rt2860 wireless n card and WPA/PSK/WPA2 connections. Funky thing is it worked in the 2.26.32-21 kernel (iwconfig shows ra0 as the wireless interface), but when the kernel was updated and pushed through in the ubuntu updates to 2.26.32-22 the wireless card won't stay connected and iwconfig says wlan0 is the interface. I checked the proprietary drivers and they said that the driver for my card was active, but not in use. How do I use the ra0 instead of wlan0?
how do i use the driver that's listed as not being used? I'm having to boot up lucid with the older kernel now, it's annoying, lots of programs aren't running as expected as a result. I've tried manually installing the driver from the RaLink website as detailed in many other posts concerning this wireless card. It seems to work for some people, but not with me.
I recently reformatted and dual partitioned to both Windows 7 as well as ubuntu 10.10. Loading works fine and Windows 7 is 100% operational. I cannot seem to get my wireless network adapter to be read by Ubuntus 'Windows Wireless Drivers' gui. Here are the steps that I have done THUS far, to make sure that we are all on the right path. Before I go any further, my wireless network adapter is an old school WUSB11 Linksys Wireless Network Adapter (running version 2.6).
1) Downloaded and installed "ndiswrapper" from ubuntu's main website. I downloaded the common, utils and ndisgtk files and installed them accordingly.
2) I extracted these three files to the desktop of Ubuntu and accessed the terminal page.
3) From terminal I typed "cd Desktop" to change the directory to the desktop.
4) Next, I typed in "Sudo dpkg -i ndiswrapper-common_1.54-2ubuntu1_all.deb
Sudo dpkg -i ndiswrapper-utils-1.9_1.54-2ubuntu1_i386.deb
Sudo dpkg -i ndisgtk_0.8.5-1_i386.deb"
5) This installed Windows Wireless Drivers gui successfully and I can access it.
6) I have downloaded the driver files for the adapter from the cisco website and searched them for the required files needed.
7) After extracting the .INF file from the "Drivers" directory named "NETUSB.SYS" (I wasn't sure if the other associated files within the same folder needed to be present together with NETUSB so I moved everything to the desktop) I typed in "sudo ndiswrapper -i NETUSB.inf". After accessing the Windows Wireless Drivers gui I have noticed that the 'netusb' driver is present yet under it, the system states "Hardware present: No". This leads me to believe that maybe I installed incorrectly or my "fireware?" is not present? I was reading through the installation guide posted on the ubuntu website that in addition to the .INF file we also need the BIN file(s)? and SYS file(s)?.. The folder with the drivers for my adapter contains a BIN file but it is not within the "Drivers" section of the folder.
9) Upon mousing over the network Icon naturally my hardware is still not present.
10) From what I gather after the system finds the hardware I am to write into the terminal
[Code]....
My wireless suddenly no longer works either in Ubuntu 10.10 or Windows 7. Upon some investigation, I have found that my eth1 is no longer showing up as it used to.
What can I do to get my wireless back?
Right below is some current specs, while below that is an older set of specs from a while ago.
Code:
sef@sef:~$ lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
[Code]....
I have a dell 1521 and I can't get internet working, I thing the driver is no working with ubuntu 9.10
View 1 Replies View RelatedI have lenovo thinkpad, T61 with Intel 4965AGN wireless card. It is a N card, it works under N mode in windwos, but not in Ubuntu (10.10). I installed ndiswrapper and got the windows xp drivers for this card. the issue is that i got an error when installing the drivers and since then I cannot use wireless.
The error i got is: Code: Module could not be loaded. Error was: FATAL: Could not read '/lib/modules/2.6.35-24-generic/kernel/ubuntu/ndiswrapper/ndiswrapper.ko': No such file or director I unistalled the driver, but now under network connections no wireless connections appear, nothing. I cannot use wirless anymore.
wlan0 Authentication capabilities :
WPA
WPA2
CIPHER-TKIP
CIPHER-CCMP
Those are my authentication capabilities, obviously. I am using a WEP encryption for my wireless router and according to this, it will not allow me to connect. Is there anyway to allow that? The wireless card works just fine in Windows, even on the same network encryption type. Using a Intel Wireless/Pro 4965 ag. Note* this is my mother's router and whatnot. She won't change it the encryption type.
The problem with my wireless network. I have Dell DV6 Pavilion 2115 eg laptop and i installed Ubuntu 11.4 and internet and wireless worked, until i reboted my system it has disapear. I cant no longer to connect to a wireless network. It dont shows me any wireless network. My wireless card is Atheros AR 9285 802.11b/g/n Wifi Adapter
View 9 Replies View RelatedIt is. I think this might be the reason why my $wireless objects don't work in Conky?
View 4 Replies View RelatedI have an older laptop, a Toshiba Satellite Pro 6100 that has a switchable internal wireless connection. It will not connect to my router. I am using the 10,04 netbook remix. When I use lshw in terminal this is what I get:
*-network
description: Wireless interface
physical id: 1
logical name: eth1
[Code].....
Should it not be identified as wlan0? I know a whole lot about Ubuntu linux because I don't. I did a clean install over XP and am using this laptop as a learning tool for linux in hopes to divorce windows completely.
When I try to bring up my wi-fi PCI card (ifup wlan0 or ifconfig wlan0 up) my whole PC just hangs until I power it off.
I believe I have the right drivers, but cannot see what I am doing wrong.
I'd really prefer not to go down the ndiswrapper route.
Firstly, I can see the PCI card and the driver it is using :
Code:
[J@gx260-f10 ~]$ lspci -k
...
...
01:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller (rev 20)
[Code]....
the PC just hangs for ever. No mouse movement, ctrl-alt-del, nothing.
I have downloaded a Linux driver from Realtek but it will not compile. I have the latest kernel-devel, headers, and gcc. I can post compiler errors if anybody would like. They're all apparently to do with missing parameters.
I installed a Tenda W322P wireless card in my dual-boot PC running both Windows XP and Ubuntu 11.04. The card worked straight out of the box on XP, but does not function correctly under Ubuntu. My apologies for any missing/irrelevant information, I am having to post this from the Windows boot so the Ubuntu settings are not directly available at the same time as internet access.I followed the process detailed here htURL...to install and configure the driver (I believe from reading other sites that this card is the Ralink RT3062 chipset), blacklisted the original RT2860 driver that was in use (couldn't even get the card to scan for wireless networks with the default driver) and restarted the interface.
Since then, sudo iwlist scan can find my wireless router but when I attempt to connect to it, it seems to enter a loop of requesting the WEP key then pausing for a while before re-requesting the key. I know I have the key value correct because it is copied and pasted from the same text file I used to copy and paste into the passkey field on the Windows boot. Attempting to connect to the router using Ubuntu also has the rather unfortunate side-effect of crashing the wireless router, killing off all other device connections until the router has been reset.
How do I install the correct driver for my Ubuntu 10.10 system for the AR9285 wireless card? code...
View 2 Replies View Relatedinstalled UB10.10 on a dell d800 laptop with a built in wireless.The eth1 wireless device/connection shows up on the little radio icon as connected .but the chrome browser says "ERR_name_not_resolved" when I enter a common url.What's the next step or hint for gaining full internet access ?
View 4 Replies View RelatedWhen I type ifconfig,
I see wlan0 and eth0. I want to somehow bind these two together into one device.
How would I go about doing this?
i installed ndiswrapper and ndisgtk, then using my thumb drive installed my .inf file (tried in the terminal as well as ndisgtk and both worked succesfully). when i run "sudo ndiswrapper -l" my wn311b device is shown, and the chipset to be working properly. now when i run "iwconfig", Wlan0 is not listed. also i blacklisted the drivers "b43, b43legacy, ssb, and bcm43xx", could this be the issue? im running the newest build of ubuntu which i installed today on this computer for a dual boot drive with vista.
View 5 Replies View RelatedI have got Ubuntu 10.10 on a Dell Inspiron Laptop. Can't get anywhere with wireless network. Tried a few bits of poking it blindly with a stick:
matthew@ubuntu:~$ lshw -C network
Warning: you should run this program as super-user.
*-network
Description: Network controller
Product: BCM4312 802.11b/g LP-PHY
Vendor: Broadcom Corporation
Physical id: 0
Bus info: pci@0000:0c:00.0
Version: 01
Width: 64 bits
Clock: 33MHz
Capabilities: bus_master cap_list
Configuration: driver=b43-pci-bridge latency=0
Resources: irq:17 memory:f69fc000-f69fffff
*-network .....
I reckon *-network DISABLED is a problem, I tried sudo ifconfig wlan0 up but that didn't work. The output of that and lspci are on the ubuntu side of my machine. I have also tried pressing my wireless on/off key (F2) but that doesn't work either.
Just installed f14 on my Toshiba laptop, which has a realtek ethernet card. i installed the drivers from the realtek site with no issues (also, i know the card is good, i had it working on suse a while back). No matter what I try, i cannot seem to get the computer to recognize there being a wireless connection (tells me no such thing as wlan0).ifconfig shows the following:
Code:
# ifconfig
eth0 Link encap:Ethernet HWaddr 88:AE:1D:F4:AD:88
[code]...
I have configured a wireless pcmcia card using ndiswrapper. I'm sure that works, as with the command "iwlist wlan0 scan" gives me back
the list of detected wireless networks. At this point I was wondering: is there a way to detect the new interface (wlan0) with network manager? Even after enabling the wifi card the network manager gnome applet always finds only eth0.
I'm running Ubuntu 10.04 Server. I can't get my Wireless Card & Wired Card to work at the same time. My interfaces file is incorrect, when I comment out 1 of the interfaces the other works. I have attached my interfaces file.
View 2 Replies View RelatedJust installed Fedora 14 from the Live CD i686 on my Dell Inspiron 1521. I can't connect to the SpeedTouch 585 on either wireless broadcom card or the wired Ethernet card.
I can connect to it from the same Laptop on the Vista which is on dual boot on the same laptop.
Further confusing is that I ran Fedora 14 and connected to another SpeedTouch today.
Already checked the Channel on the wireless nic and it's on the same one as the SpeedTouch.
how can I send internet from wlan0 to eth1 .
View 1 Replies View RelatedI'd like to know how can I find a Linux wirelles driver for wireless Belkin card.
View 1 Replies View RelatedEarlier on my wireless is attached as eth1 and it works on to load conky except the Network section is blank. After that I had renamed eth1 to wlan0 and checked at ifconfig it is working fine.Now the conky won't load and I think something to do with my wlan0.
View 1 Replies View RelatedI recently installed Linux "Fedora" and when I click "ifconfig" I see can see the network card "eth1" I want to change it to "wlan0", I realized that this is a common enough problem at Fedora, and I read about it a bit on Google but unfortunately I did not understand how to change it correctly. give me the order strictly Consul that allows Linux to change the name of my network card
View 14 Replies View RelatedI have a Dell inspiron 1420 and its set up as a dual boot. Windows/Fedora.I cant get the wireless card to work. I review some previous posts but still cant get it working.
I did a /sbin/lspci
Network controller: Broadcom Corporation BCM4310 USB Controller (rev 01)
I did $rpm -q b43-fwcutter
b43-fwcutter-011-3.fc9.i386