Ubuntu Networking :: Discovering Network Printers And Configuring Routes
Apr 6, 2010
1. My machine [running Karmic Koala] is part of a corporate LAN with NIC details below
Quote:
2. My routing table:
Quote:
3. The network printer's details [as read from the printer's display interface]:
Quote:
My question:
This printer can be discovered by windoze machines using "Find printers" and then added. [Am not sure how this works!]
But when I try to discover the same from my ubuntu machine, its not getting discovered. Tried pinging the ip [172.20.254.158] which gives the following:
Quote:
Now I tried fiddling around with the route command along with good amount of googling but to no avail.
1. Is there a way I could add that printer to my machine?
2. If yes, how could I? Does it involve adding routes?
View 2 Replies
ADVERTISEMENT
May 8, 2011
How do I add a route that doesn't go away after a reboot? I tried adding to /etc/sysconfig/network-scripts/route-wlan0 and /etc/sysconfig/static-routes but neither of them did anything when I restarted network and NetworkManager. route command does not show the new route that I added. I tried this too - routes.html and there were no errors but the new route doesn't show up with the route command.I added "192.168.13.88/255.255.255.255 via 192.168.13.101 dev wlan0"
View 2 Replies
View Related
Jan 28, 2010
I've been using Kubuntu 9.10 for several months now. For most of that time, I configured and used with no problem several network printers.. a HP LaserJet 3015 at home connected to a Windows machine, and a Xerox Phaser 8560 at my coworking space connected directly to a router.
However, several weeks ago I was at the coworking space, requested a print from my web browser, and in the printer selection dialog, observed the list of printers expanding... some sort of autodetection of network printers was occuring, and multiple instances of the same printer were being offered, with slightly different names. Printing to these devices did not work.
Now, after a reboot, there are NO network printers available no matter what network I'm connected to. When I use the Kubuntu printer configuration tool and try to set up a new printer, it asks me to "Select a connection" to which the only option it gives me is "Other". When I put in an address for the printer it just cycles endlessly, never finding anything.
View 3 Replies
View Related
Jan 13, 2010
I currently managed it to get a pptp-connect to my home network. now I have another little problem. NetworkManager always routes the whole network traffic over my home network if i am connected to the home network.If i set the "Use this connection only for resources on its network" I have do manually say:
Code:
route add -net 192.168.1.0 netmask 255.255.255.0 dev ppp0
After that only the correct traffic runs over the vpn. Now my question is it possible to setup the route via the networkmanager gui?
View 3 Replies
View Related
May 10, 2011
First I will give some background. We have a currently working network that the Previous network Admin assigned an internal IP scheme of 200.1.1.0/24. I have no idea why he would have done such a thing, but it is my job to fix it (and keep our systems up and running). We have a Fedora 10 box on the 200 network that is acting as a router and a firewall (shorewall to be exact).
I added another NIC card (thank you again to all the great people on this forum for helping me get that working) and it is eth2. Assigned it a 10.100.1.A/24 (This is just a variable for the real IP). The other end of the cable that I plugged into that NIC connects to a Cisco Layer 3 switch. I assigned the port that connects to the other end of the cable the IP address of 10.100.1.B/24
Ok, I added the static route of ˜ip route add 10.100.1.0/24 via 10.100.1.A dev eth2' I added loc2 (which is my eth2 adapter) to the /etc/shorewall/zones file. I set eth2 on loc2 in the /etc/shorewall/interfaces file. loc2 eth2 detect I set the lines in the /etc/shorewall/policies file loc loc2 ACCEPT info loc2 loc ACCEPT info I can ping the cisco switch from the linux server itself. From a PC on the original network I can ping the new NIC card in the linux server, but cannot ping the cisco switch, so I figure it has to be either the route or shorewall.
View 13 Replies
View Related
Feb 15, 2010
I've had Kubuntu 9.10 32-bit running on my laptop since it came out, but in the past month all its networked printers have disappeared from the configuration, and I can't set up any more. I've been through the forums again and again and cannot fix it. I've installed and reinstalled lots of packages related to CUPS but it doesn't seem to make a difference.I'm not sure what has happened, but I have lots of clues. Since I'm reaching the limit of my know-how here, I'll just list all the clues.
I'm pretty sure the problem is in my Kubuntu laptop, because in my SOHO setup I also have a Kubuntu 9.10 desktop (this time 64 bit) connected to a printer, and I have successfully printed through that from both a Windows XP laptop and a Xubuntu 9.10 box.On the Xubuntu 9.10 box, I just asked for the GUI print configurator and it automatically detected the network printer. No muss no fuss.But on the Kubuntu laptop, when I go into the print configurator, here's what happens:
- it shows two options, "new printer" and "server settings" (image a.png)
- entering "server settings" everything is greyed out and unchangeable (image b.png)
- entering "new printer" shows only one option for a connection, "other" (image c.png)
- after entering the address of a printer i know works (image d.png) the configurator has detected the printer (image e.png)
- but then attempting to move forward it crashes with no explanation.
Running the non-kubuntu version of the configurator GUI provides a bit more information before it fails. When I try to access the desktop with the printer attached it wants a username and password. (which wasn't necessary for the two client machines who successfully printed.) And at the end of the process there is an error: "there was an error during the CUPS operation: client-error-forbidden".
Two more clues:
- when I try to go with my browser to localhost:631 the browser can't establish a connection
- but I can see the cups page on the printer's host machine at 192.168.0.104:631 no problem.
View 2 Replies
View Related
Jul 28, 2010
Is there an ink level app that works with network printers? I am currently using Ubuntu Lucid x64 with a Canon MX860 printer that was installed using this tutorial: [URL]. Everything seems to work fine (it prints) but I cannot get any of the ink level apps to work (Mtink or Inkblot). After doing some research, my conclusion is those apps only work with USB connected printers. Is that true?
View 3 Replies
View Related
Mar 1, 2010
I have Ubuntu Server 9.10 up and running as my file server. However, it sits amongst other PCs running XP Pro and Network Printers (e.g. Xerox Docuprint C2535A) on the network. My question is whether there is a way of adding the Xerox printer to the Ubuntu Server so that other PCs will send print jobs through the server. I think the printer is windows-based printer. Is it possible to do this? or are there any other options that you may be able to share with me?
View 3 Replies
View Related
Apr 15, 2010
I need help setting up network printers I have two computers, they both have ubuntu on them. The internet comes in to the first computer on a usb modem, it is routed out from ethernet to wireless. I used CUPS on computer two and printed out a test page that worked, but it won't print out anything else.
View 1 Replies
View Related
Nov 3, 2010
I can't install printers shared by a computer running Windows 7, I try to add a new printer using samba, it shows me the other computers but I cant see any printers.
View 4 Replies
View Related
Feb 8, 2011
Suppose that I am in a private network of computers (say each having ip addresses 192.168.. ). Some of the machines( we have no information regarding their ip, name and no physical access to the servers) in the network are connected to internet and they run an http proxy at some port say 3128. Is there a program which can be run on Windows or Linux which will give me the list of machines(ip addresses and ports if possible) acting as proxy servers?
View 1 Replies
View Related
Apr 7, 2011
I am totally new to Linux and have just installed ubuntu 10.10. After configuring the network interface via dhcp I started getting these messages that come in so frequently I can't configure anything else.
[87.186415] Stack:
Why I am getting this messages and more importantly how do I get rid of them.
The installation is on a VM on Hyper-V.
View 1 Replies
View Related
Feb 14, 2011
entries for connecting to broadband. Was OK with ubuntu 8.04 which had boxes for DNS server, etc. The 10.04 asks for MAC address (?) and there is a space for "DHCP client ID". I don't understand these terms. how I may proceed, especially exact syntax for any command line work. I am in Chennai/Madras, and have a BSNL wired broadband connection to my Dell laptop.
View 5 Replies
View Related
Feb 16, 2011
"Need help with entries for connecting to broadband. Was OK with ubuntu 8.04 which had boxes for DNS server, etc. The 10.04 asks for MAC address (?) and there is a space for "DHCP client ID". I don't understand these terms. I will appreciate some step-by-step instruction or example of how I may proceed, especially exact syntax for any command line work. I am in Chennai/Madras, and have a BSNL wired broadband connection to my Dell laptop." I have repeated what I tried in the ubuntu forum without success. I'm really in newbie category, and not comfortable with computer or internet jargon. I can still connect with ubuntu 8.04 and firefox, just once daily. In a later post I also added: In Ubuntu 8.04 there was a system> admin> network tab (missing in 10.04). In the connections tab "wired" was checked. The general tab had my computer name (tsq-laptop) for host, and a blank box for domain name. The DNS tab had 192.168.1.1 in the servers box (presumably my service provider BSNL), and nothing in search domains. The hosts tab had a list of IP addresses and aliases, the first few being:
127.0.0.1 - local host
127.0.1.1 - tsq-laptop
::1 - ip6 local host ip6 loopback
fe00:: - ip6 localnet, .... (and a few more such I think most (or all) of these entries were generated automatically by the system, since I don't understand the jargon at all! I don't recall having any difficulties then, some two years back.Before that I had major problems in using the internal modem for a dial-up connection, but got detailed help by e-mail/internet from some really knowledgeable people in Europe and elsewhere regarding linmodem configuration, which I followed blindly and it worked!
In 10.04 there is only the taskbar icon to edit settings, and it has a different structure. It asks for MAC address (example 00.11.22.33.44.55). Other info required is IPv4 settings, DHCP client ID, about routers and other stuff. There may be other system settings to be made, which I can try with proper guidance. The ubuntu help page gives very sketchy information, and the images are not clear at all. No response to that till second day. Subsequently: In the 'wired' tab the 'routes' button popped a table where I entered address as 127.0.0.1, and netmask as 255.0.0.0, leaving gateway and metric blank. This is all geek stuff for me - I'm an old-fashioned engineer from the slide-rule era!
Should all this have been in the newbie forum? Thanks, =TeeSquare=
View 11 Replies
View Related
May 10, 2010
Total Newb here, sorry. I am pseudo-IT at work and have set up a desktop with Debian 5 (accidentally overwrote Windows in the process, but there you go). We are set up with network printers here (all Windows), and I was wondering how to go about being able to print to one of the network printers from my Linux desktop. Can I even connect to the Windows network with this desktop (it is hooked up)? Understand, I do NOT want to screw up anything on the network - they won't let me play anymore if I do. If I download the Linux driver, what do I do next?
View 2 Replies
View Related
May 19, 2010
My DNS server is baring 192 series IP for ex: 192.168.10.100, need to configureloadbalancer IP in that DNS server, where loadbalancer is baring 172 series IP. for ex : 172.56.67.19.is it possible to cofigure the loadbalancer ip in DNS server? if it is, please let me know the configuration details and procedure.
View 2 Replies
View Related
Mar 12, 2009
Does anyone havea good tutorial on Fedora's network scripts, how to edit them, in what order they are called, etc. What I want to do seems simple, but something in the bootup keeps changing it. Right now, I have an image of Fedora Core 7 created in a server with 2 Ethernet cards. I need to specify static IP addresses for each card. Thats simple, and I did that. Now, heres the tricky part, I need to be able to clone this image and place it onto other exact duplicates of the hardware, and have all of the settings stay the same.
What happens here, is that eth0 and eth1 are stored somewhere as devices, and upon boot on a different machine, the Fedora will mount new network cards(different MAC addresses) as eth1 and eth2. It then mvoes my ifcfg-eth0/1 to a backup, and creates two brand new network setting's files, which initialize to DHCP. This creates an issue, becuase these machines do not have monitors nor keyboards attached, nor is their a DHCP server, so its a pain when I swap the machine out, to have to go in with a keyboard/mouse/monitor and reconfigure the network settings before I can connect to it over the LAN.
So does anyone have any advice on how to do this? No matter what i tried, booting the image in a new PC caused Fedora to create two new devices and create brand new network settigns for them, both initialized to DHCP. Hell, I wouldn't care if it created brand new devices, if it would initialize them to static IP addresses that I am expecting.
View 1 Replies
View Related
May 18, 2010
First off I would like to install a GUI for samba. After that I want to set up my network so that router stays as the server for the network I have four windows computers already hanging off of the router. This machine which has Slackware on it is hardwired, directly connected, to the router via cat-5 cables. I have samba installed already and I just need to configure it correctly.
View 4 Replies
View Related
Jun 27, 2010
For some simulation, I am trying to configure a setup of 3 ubuntu desktops (one of them with multiple network cards) to behave in the following way:
Each one of them should be a separate network not seeing the others (including multicast addresses) They need to have internet access through the machine with multiple network cards. So from the point of view of each machine they define a LAN in which it is the only device and have internet access through the gateway machine.
What do I need to do to configure these machines for the above setup?
View 6 Replies
View Related
Oct 9, 2010
I have a shared printer on my Ubuntu 10.04 machine, and it cannot be seen by other computers (macbook, pc) on the network. I have the printer shared, but it is not a member of the 'Shared Printers' group. When I add it to the 'Shared Printers' group, it stays there until I close the 'Printing' application GUI. Then, when I re-open 'Printing,' it is no longer in that group. I think this is why I can't see it on the network, due to the wording of the option in Server Settings to 'Publish shared printers connected to this system.'
View 3 Replies
View Related
Aug 25, 2011
I am trying to configure my IPv6 network. My computers are behind a Fedora gateway IPv6-configured, which is working great. But for computers inside my network, it seems I am getting only internal addresses from DHCP. Here is my ifconfig for an internal computer:
Quote: em1 Link encap:Ethernet HWaddr F4:6D:04:34:92:2B inet addr:192.168.0.184 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f66d:4ff:fe34:922b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:744250 errors:0 dropped:0 overruns:0 frame:0 TX packets:548987 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:841392242 (802.4 MiB) TX ytes:60384500 (57.5 MiB) Interrupt:18 Memory:f7100000-f7120000
he-ipv6 Link encap:IPv6-in-IPv4 inet6 addr: 2001:470:1c:611::3/64 Scope:Global inet6 addr: fe80::cea7:b778/128 Scope:Link UP POINTOPOINT RUNNING NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:61 dropped:0 overruns:0 carrier:61 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
[Code]....
View 2 Replies
View Related
Sep 1, 2010
I have a ubuntu 10.04.1 install with openvpn, so I have some routes in my /etc/networking/interface file. But for what ever reason when it boots the routes don't come up and I have to restart the networking before they come up. Once I do that all is well. Any idea's why it's doing that?
View 1 Replies
View Related
Sep 18, 2010
I'm a newbie on lucid lynx 10.04
The Hardware:
Mac Mini late 2009 running 10.6.4 (Snow Leopard/OS X)
Dell Dimension 2400 running Ubuntu 10.04 Lucid Lynx
HP Photosmart C4680 multifunction printer/scanner/copier
Canon PIXMA MX310 multifunction printer/scanner/copier/fax
Netgear Wireles-N 150 router model WNR 1000v2
[Code]...
As the HP Photosmart printer is currently connected, it is visible over the network by the macintosh however will not print (all jobs appear in the macintosh's queue without a "hold" designation, printer not on pause. pause/resume only changes the tag on the printer but does nothing to cause the queue to begin printing). Although I can navigate within the printer setup to the existing printer on the network, I cannot connect the printer on the mac without finding a new "printer" instance on the Ubuntu machine when I get there. The printer instance which works is the one the Ubuntu machine created, and the printer instance which does not work is the one generated by the mac, which doesn't work either from the mac or when printed to from the Ubuntu machine, now that this instance exists there.
With the printer connected to the mac, it is visible over the network to the ubuntu box however asks for authentication for the print queue and will not accept any password established for either machine. It also does not specify what account name the password should match with so is an utter quandary.
lastly, I did run dmesg but the result was too large for my terminal's log and scrolling back through it I did not find a section relevant to the HP (or Canon) printer to post here.
View 1 Replies
View Related
Sep 1, 2010
I have a ubuntu 10.04.1 install with openvpn, so I have some routes in my /etc/networking/interface file. But for what ever reason when it boots the routes don't come up and I have to restart the networking before they come up. Once I do that all is well.
View 4 Replies
View Related
Sep 1, 2011
I am using Fedora 12. I am connected by Wi-Fi to a large network with dozens of printers (the network is running CUPS). How can I set up my fedora box to "see" those printers so that "print..." file menu option works? Also, I know the address of the CUPS server; when I go to System->Administration->Printing and I go to Server->Connect I can connect successfully and I can see all the many printers on the network. But I haven't figured out how to print from my favourite programs yet.
View 1 Replies
View Related
Jul 18, 2010
New ubuntu desktop user here. I've been working with Ubuntu servers for over 3 yrs, using Windows as clients. I have OpenVPN running on an ubuntu 10.04 server, and it has worked well with Windows OpenVPN clients connecting. I took those same settings and applied them to this new install of Ubuntu 10.04 Desktop, and now openvpn seems to be failing when we get to the routes (I wrestled with the network-manager "secrets" issue for hours, but that works now).
I performed the following:
sudo openvpn --config fogbank-ny1.ovpn
--all is well, we're connecting/yay then *screech* FAIL--
Code:
Sun Jul 18 07:17:14 2010 PUSH: Received control message: 'PUSH_REPLY,route 10.8.0.0 255.255.255.0,redirect-gateway def1,dhcp-option DNS 10.8.0.1,route 10.8.0.0 255.255.255.0,topology net30,ping 30,ping-restart 600,ifconfig 10.8.0.10 10.8.0.9'
Sun Jul 18 07:17:14 2010 OPTIONS IMPORT: timers and/or timeouts modified
Sun Jul 18 07:17:14 2010 OPTIONS IMPORT: --ifconfig/up options modified
Sun Jul 18 07:17:14 2010 OPTIONS IMPORT: route options modified
Sun Jul 18 07:17:14 2010 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified
Sun Jul 18 07:17:14 2010 ROUTE default_gateway=192.168.10.1
Sun Jul 18 07:17:14 2010 TUN/TAP device tun0 opened
Sun Jul 18 07:17:14 2010 TUN/TAP TX queue length set to 100
Sun Jul 18 07:17:14 2010 /sbin/ifconfig tun0 10.8.0.10 pointopoint 10.8.0.9 mtu 1500
Sun Jul 18 07:17:14 2010 /sbin/route add -net <mypublicip> netmask 255.255.255.255 gw 192.168.10.1
Sun Jul 18 07:17:14 2010 /sbin/route add -net 0.0.0.0 netmask 128.0.0.0 gw 10.8.0.9
Sun Jul 18 07:17:14 2010 /sbin/route add -net 128.0.0.0 netmask 128.0.0.0 gw 10.8.0.9
Sun Jul 18 07:17:14 2010 /sbin/route add -net 10.8.0.0 netmask 255.255.255.0 gw 10.8.0.9
Sun Jul 18 07:17:14 2010 /sbin/route add -net 10.8.0.0 netmask 255.255.255.0 gw 10.8.0.9
SIOCADDRT: File exists
Sun Jul 18 07:17:14 2010 ERROR: Linux route add command failed: external program exited with error status: 7
Sun Jul 18 07:17:14 2010 Initialization Sequence Completed
I am using the suggested openvpn routes. If I connect from Windows (actually the .ovpn file is taken directly from the working windows machine).. all is well, routes work fine all traffic is routed thru the VPN -- same way it's worked for over a yar. I assume that this is what is causing networkmanager to fail as well. those logs indicate that it has connected to the vpn, but is probably stopping when it gets to routes.
View 1 Replies
View Related
Oct 15, 2010
I've got a 10.04 machine with two ethernet interfaces. I have two separate outside internet connections. This machine is connected to both interfaces. But it DOES NOT route between them. It's just a host on both subnets. Again, no routing is to go through this host. I'd like to force traffic originating on each ethernet port out to that network's internet connection.
Here's the desired setup:
eth0 192.168.12.37/24 gw 192.168.12.1
eth1 192.168.1.37/24 gw 192.168.1.1
I'd like traffic on the 192.168.1.37 address to go out through the 192.168.1.1 gateway. I have a program bound to that address and need it's traffic to go out ONLY through the 192.168.1.1 gateway. Any other traffic on the machine should go out the 192.168.12.1 gateway.
The logic is: source IP is 192.168.1.37, dest IP is any then go out only through 192.168.1.1 source IP is 192.168.12.37, dest IP is any then go out through 192.168.12.1 first or 192.168.1.1 next. The point is source on the .1.37 address must always go out the .1.1 gateway and NEVER through .12.1. Whereas traffic on the .12.37 address should try going out the .12.1 gateway first but can go out the .1.1 gateway if the .12.1 connection is down. I could live with this failover option. I could accept that traffic on the .12.37 address was likewise limited to its own gateway.
View 3 Replies
View Related
Dec 3, 2010
I just set up NIC bonding in Ubuntu 10.4, following these instructions, and I've got it working except for one problem: Every time I up or down a network device, or every time the system reboots, my routes go all to hell with eth0 and eth1 entries next to my bond0 entries. When the eth0 and eth1 entries show up, my connection is hosed and I have to go in via the maintenance IP to kill each route one at a time, leaving only bond0. Here's how I want my routes to look at all times:
Code:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
10.87.9.0 0.0.0.0 255.255.255.0 U 0 0 0 bond0
0.0.0.0 10.87.9.1 0.0.0.0 UG 100 0 0 bond0
Here's my /etc/network/interfaces:
[Code]...
View 3 Replies
View Related
Apr 27, 2011
On a server with 4 network interfaces, sometimes not all 4 are plugged in. All 4 interfaces have the same IP address. Sometimes the machine cannot access the local LAN, but can access the internet via a router on the local LAN, after a reboot. What I find is that the routing table looks like this:
Code:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
172.30.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0
172.30.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1
172.30.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth2
172.30.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth3
0.0.0.0 172.30.0.2 0.0.0.0 UG 1 0 0 eth0
0.0.0.0 172.30.0.2 0.0.0.0 UG 2 0 0 eth1
0.0.0.0 172.30.0.2 0.0.0.0 UG 3 0 0 eth2
0.0.0.0 172.30.0.2 0.0.0.0 UG 4 0 0 eth3
On the console I cannot reach any local host, but I can reach internet hosts. Pinging the gateway router 172.30.0.2 gets no answer. When I manually change it to this:
Code:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
172.30.0.0 0.0.0.0 255.255.0.0 U 1 0 0 eth0
172.30.0.0 0.0.0.0 255.255.0.0 U 2 0 0 eth1
172.30.0.0 0.0.0.0 255.255.0.0 U 3 0 0 eth2
172.30.0.0 0.0.0.0 255.255.0.0 U 4 0 0 eth3
0.0.0.0 172.30.0.2 0.0.0.0 UG 1 0 0 eth0
0.0.0.0 172.30.0.2 0.0.0.0 UG 2 0 0 eth1
0.0.0.0 172.30.0.2 0.0.0.0 UG 3 0 0 eth2
0.0.0.0 172.30.0.2 0.0.0.0 UG 4 0 0 eth3
Then all is well (can ping local hosts including the gateway router). I do have metric specified in the /etc/network/interfaces file like this:
Code:
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static
address 172.30.16.8
netmask 255.255.0.0
network 172.30.0.0
broadcast 172.30.255.255
metric 1
auto eth1
iface eth1 inet static
address 172.30.16.8
netmask 255.255.0.0
network 172.30.0.0
broadcast 172.30.255.255
metric 2
auto eth2
iface eth2 inet static
address 172.30.16.8
netmask 255.255.0.0
network 172.30.0.0
broadcast 172.30.255.255
metric 3
auto eth3
iface eth3 inet static
address 172.30.16.8
netmask 255.255.0.0
network 172.30.0.0
broadcast 172.30.255.255
metric 4
Apparently that metric setting applies only to the gateway route, not the LAN route. Is there a way to specify the LAN route metric, too?
View 1 Replies
View Related
Oct 28, 2010
I have some CISCO,Linux related problem with 2 Class C subnets:
192.168.64.0 -> PC5
192.168.65.0 -> PC6
Here's a picture of my situation: [URL]
HQ has to have 2 STATIC routes in order those 2 "PCs" mentioned above to have end to end connectivity with NETWORK A and NETWORK B. Now I try with
route0 -> network: 0.0.0.0, mask: 0.0.0.0, nexthop: Serial 0/0/0
route1 -> network: 0.0.0.0, mask: 0.0.0.0, nexthop: Serial 0/0/1
And it seems to work but I don't think it's proper! I feel it's kinda wrong ... but all my other attempts to set another couple of static routes ends in "Request timed out" and thus connection lost.
View 1 Replies
View Related
