Fedora Networking :: Network-Manager PPTP Add Routes
Jan 13, 2010
I currently managed it to get a pptp-connect to my home network. now I have another little problem. NetworkManager always routes the whole network traffic over my home network if i am connected to the home network.If i set the "Use this connection only for resources on its network" I have do manually say:
Code:
route add -net 192.168.1.0 netmask 255.255.255.0 dev ppp0
After that only the correct traffic runs over the vpn. Now my question is it possible to setup the route via the networkmanager gui?
View 3 Replies
ADVERTISEMENT
Feb 25, 2010
I have updated the system this morning and the vpn stopped working!It gives me an error: invalid secrets.I use network manager to connect to a pptp vpn connection, I use fedora 12.Does anyone know the problem?
View 2 Replies
View Related
Dec 1, 2009
I can not stablish PPTP VPN because SELinux blocking Network Manager.
I get the following:
Summary: SELinux is preventing NetworkManager (NetworkManager_t) "unlink" to ./reso
Code:
I'm attaching complete alert.
View 1 Replies
View Related
Mar 12, 2010
i can't install network-manager-pptp package with offline.i get this package from Code:http://packages.ubuntu.com/karmic/i386/network-manager-pptp/downloadJust now i use ubuntu9.10.
View 3 Replies
View Related
Mar 24, 2010
I followed (or at least tried to follow) tutorials on doing this. I installed network-manager-pptp and tried to configure network manager to connect to a VPN. In the settings when I select MPPE with 128-bit encryption, after I've selected it and applied it, I check the settings and it's invariably unchecked. I tried using KVpnc after getting frustrated with network manager, and I can't seem to get that working either. I've been trying to search for info on this, and I can't seem to find anything on why I can't select MPPE with 128-bit encryption. That seems like it might be why I'm unable to connect to the VPN?
View 1 Replies
View Related
Sep 15, 2010
I successfully installed openvpn and networkmanager openvpn plugin. Then I successfully added a PPTP vpn connection by networkmanager vpn tab which name is "vpn1". But now I don't know how to connect to this PPTP vpn connection. I tried bellow command but no luck.
openvpn --config vpn1.config
View 3 Replies
View Related
Jul 27, 2010
I have ~20 log entries/second in syslog
Code:
nm-pptp-service-1078 log[decaps_gre:pptp_gre.c:414]: buffering packet 57467 (expecting 57429, lost or reordered)
[code]....
View 1 Replies
View Related
May 8, 2011
How do I add a route that doesn't go away after a reboot? I tried adding to /etc/sysconfig/network-scripts/route-wlan0 and /etc/sysconfig/static-routes but neither of them did anything when I restarted network and NetworkManager. route command does not show the new route that I added. I tried this too - routes.html and there were no errors but the new route doesn't show up with the route command.I added "192.168.13.88/255.255.255.255 via 192.168.13.101 dev wlan0"
View 2 Replies
View Related
Oct 27, 2010
I've searched the forums (250 thread limit) for a fix on this, but all the questions seem unanswered or unrelated. My situation is this: I'm running Ubuntu x64 10.10 'Maverick'. I have a cablemodem connection for my Internet access. I have home network running on DD-WRT with the dreadful Linksys WRT54G series router.
My DD-WRT router is 192.168.1.1, subnet 255.255.255.0.
My Linux box is 192.168.1.61, subnet 255.255.255.0.
I have a VyprVPN connection set up successfully on Linux. Mostly everything works great, speed's fine, latency is what I expect it to be. Except... I also run an SSH server to remotely admin the box at port 22, an Apache server running over SSL at port 7001, and a Transmission web client at port 7002 (only secured by basic HTTP realms auth). All of these things worked before I got the VPN working, I'm of course using NAT at the DD-WRT router.
The endresult I am looking for, is to have the security and protection of the VPN (even if it's only perceived) for everything I do on this machine -- EXCEPT on Apache, the Transmission web panel, and the SSH server, which I want to access from the outside world. I have no firewalls running or configured, not even iptables, not even the SPI firewall on DD-WRT. All connections to the aforementioned services from the outside world timeout coming in to the Linux box. They all work from inside my home network (182.168.1.0/24). In case it's needed, he's my routing:
[Code]....
View 2 Replies
View Related
May 10, 2011
First I will give some background. We have a currently working network that the Previous network Admin assigned an internal IP scheme of 200.1.1.0/24. I have no idea why he would have done such a thing, but it is my job to fix it (and keep our systems up and running). We have a Fedora 10 box on the 200 network that is acting as a router and a firewall (shorewall to be exact).
I added another NIC card (thank you again to all the great people on this forum for helping me get that working) and it is eth2. Assigned it a 10.100.1.A/24 (This is just a variable for the real IP). The other end of the cable that I plugged into that NIC connects to a Cisco Layer 3 switch. I assigned the port that connects to the other end of the cable the IP address of 10.100.1.B/24
Ok, I added the static route of ˜ip route add 10.100.1.0/24 via 10.100.1.A dev eth2' I added loc2 (which is my eth2 adapter) to the /etc/shorewall/zones file. I set eth2 on loc2 in the /etc/shorewall/interfaces file. loc2 eth2 detect I set the lines in the /etc/shorewall/policies file loc loc2 ACCEPT info loc2 loc ACCEPT info I can ping the cisco switch from the linux server itself. From a PC on the original network I can ping the new NIC card in the linux server, but cannot ping the cisco switch, so I figure it has to be either the route or shorewall.
View 13 Replies
View Related
Mar 14, 2009
I used VPN before in Windows only.
How can I connect to VPN network by PPTP protocol in a simple way ?
View 12 Replies
View Related
Apr 6, 2010
1. My machine [running Karmic Koala] is part of a corporate LAN with NIC details below
Quote:
2. My routing table:
Quote:
3. The network printer's details [as read from the printer's display interface]:
Quote:
My question:
This printer can be discovered by windoze machines using "Find printers" and then added. [Am not sure how this works!]
But when I try to discover the same from my ubuntu machine, its not getting discovered. Tried pinging the ip [172.20.254.158] which gives the following:
Quote:
Now I tried fiddling around with the route command along with good amount of googling but to no avail.
1. Is there a way I could add that printer to my machine?
2. If yes, how could I? Does it involve adding routes?
View 2 Replies
View Related
Jan 7, 2011
I am trying to connect to a PPTP VPN at work, and I cannot accomplish that. Both server and client are using Ubuntu 10.10.
Code:
Jan 7 11:32:26 multicore-dev03 NetworkManager: <info> Starting VPN service 'org.freedesktop.NetworkManager.pptp'...
[code]....
View 9 Replies
View Related
Mar 13, 2010
i have a VPN server PPTPD on Centos 5.3
eth0: 62.2.2.x (public on the internet)
GW: 62.2.2.1 (cisco router)
i want to configure my ppptp server to allow users access internet with their own public ips of class 62.2.3.0 62.2.4.0 62.2.5.0
every time i configure my server all users can get thier IPs but they only go out with my server IP same as NAT not routing.
can you show me the proper configuration to make my users connect with public IP and have internet access. use specific DNS ( i did this but some users can not brows by DNS)
is there any way to specify an expired date for each pptp user.
View 1 Replies
View Related
Sep 17, 2009
I'm trying to connect to a Microsoft ISA PPTP server from my Linux box. The box I'm connecting from is itself a router. I have no problem connecting a Windows XP machine to the VPN via this machine. This is fine, but I would rather connect via the Linux machine, giving me far more advanced routing options (i.e. no to send every packet from the XP box completely unnecessarily via the PPTP tunnel). The Linux router is running Debian Lenny.
I've checked iptables. There were initially some issues. I've fixed those.
Invoking pppd from the console, I can see that authentication succeeds, but then some negotiation goes wrong and the server terminates the connection. Here's the output from pppd, with the more sensitive stuff removed:
Code:
<hostname>:~# pppd call <peer> nodetach debug
using channel 19
Using interface ppp0
Connect: ppp0 <--> /dev/pts/2
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xe3e45f75> <pcomp> <accomp>]
code....
View 1 Replies
View Related
Mar 11, 2009
I updated my FC10 just a day back. The problem is that Netwrok Manager has disappeared. And in spite of re-installing it, it doesn't appear on the panel when i enter 'NetworkManager' as root in the terminal.I have a USB modem right now. Update was made through a broadband connection. Ethernet works perfectly well but this USB modem of mine doesn't work at all. And I have to use USB not Ethernet.
View 9 Replies
View Related
Jul 7, 2009
I have got DHCP issues with Network Manager. Whenever I try to connect using static IP it works, but when I use use Netowork Manager with DHCP, it seems to try to connect and soon says "Network Disconnected"..I've managed to connect to wlan and eth using network, so there shouldn't be any hardware/driver issue.
View 4 Replies
View Related
Jan 20, 2009
I have run Fedora 9 and 10 on my Dell Inspiron 640m for about 6 months now and generally experience very few issues with it. Specifically I've been running Fedora 10 KDE 64bit since it was launched. Up until I had to reload it a couple of weeks ago my Vodafone Huawei E172 3G dongle worked perfectly with Network Manager. Since the reload the dongle is detected by the OS (lsusb lists it correctly, etc) but nothing I do will make it appear in Network Manager.
I've tried manually configuring a GSM connection then plugging it in, but no joy. I've also tried using it in my Acer Aspire One which runs Fedora 10 XFCE and it work, but when I try it in another Dell Laptop running Fedora 10 KDE 64 bit it doesn't. I'm assuming that a recent update must have caused some issue as it has definitely worked in both Dell laptops in the past. As mentioned I've reloaded recently but the other laptop hasn't been.
I'm unsure where to go from here. I haven't been able to get Vodafone's beta drivers working under F10 (although I did under F9) and can't find any posts on this issue. The version of Network Manager that I'm running is NetworkManager-0.7.0-1.git20090102.fc10.src.rpm, which was released shortly before I reloaded. Chances are I just didn't try my dongle between the update coming out and the reload, so didn't notice the problem before hand.
View 14 Replies
View Related
Mar 10, 2009
I'm running Fedora 10. My Network Manager settings are all grayed out. They are uneditable. I can see the detected settings, but not change them. All of the settings fields are disabled.
Is there a way to enable these, so that they can be edited?
Starting with the menu in the upper left corner of the GNOME screen: System/Preferences/Internet And Network/Network Connections
The Network Manager window appears correctly.
I see all automatically generated settings that were created for my various devices:
In particular, I want to be able to edit "Auto vmnet8", for VMware usage.
I know about the workaround of going back to the manual network configuration as used in older versions of Fedora, such as editing the files in /etc/sysconfig/network-scripts/ifcfg-* and then enabling the old "network" service and disabling the "NetworkManager" service.
However, this workaround really won't work in this situation. The VMware interfaces, vmnet1 and vmnet8, are virtual interfaces that *only* exist when the VMware services are running. The VMware services are started *after* the old manual network configuration would be applied. So, at the time the scripts in /etc/sysconfig/network-scripts are processed, the vmnet1 and vmnet8 devices do not yet exist! I'm hesitant to change the numbering of services, lest other things break (VMware on Fedora 10 is rather fragile already).
I love the feature of NetworkManager to be able to automatically apply settings to newly materialized network devices (such as vmnet1 and vmnet8 when VMware is loaded). However, I need to also be able to edit those settings.
Is there a solution that will make my Network Manager "Edit" window not be entirely grayed out? I can see the settings pages just fine, but unfortunately, they are all disabled and I can't edit them at all.
View 11 Replies
View Related
Jun 23, 2009
I got a little problem with network manager. I got two connections in it, with two different DNS-Servers, because the one of my provider is very slow I surf with opendns, but sometimes that slows down too, so I want to change if necessary. Both connections got the same fixed IP.That worked all fine, until I got my new router (it's a Netgear WGU 624). It's connected by cable and I configured it like the old one. But for some reason instead of connecting to the manually configured connections, my fedora 10 creates a new one "auto eth 0" with a dynamic IP. So every time I boot or switch on from standby my PC connects with this one and I have to manually set it to the right connection. There's no chance to edit or delete it cause those two buttons are grey and won't work. I also tried restarting network manager manually and I also tried starting it with su as root.
View 14 Replies
View Related
Jul 20, 2009
I lost my network manager applet after removing kde-desktop. restore it, as I dont find it in add to panel applications I dont have any clue, also how could I add bluetooth applet in notification area.
View 5 Replies
View Related
Mar 27, 2010
After an update in mid-February I can no longer get Network Managero run anyinterface. I tried downgrading ppp, but that did not help. I have tried to delete all devices, but there is no user interface from which I can do that. Network Manager does not appear in any system tray. I even did a complete remove and reinstall, to no avail.This is true on both 32 and 64 bit Fedora 12, and on laptops, desktops and VBox VMs.Here is what I see in messages.log:
Code:
Mar 27 12:09:46 vmf11x64 NetworkManager: <info> Activation (eth0) Stage 4 of 5 (IP6 Configure Timeout) scheduled...
[code]...
View 14 Replies
View Related
Dec 21, 2010
I'm trying to share internet connection with my wifi capable mobile device. For that I'm creating ad-hoc wifi connection in networkmanager with 'shared to other computers' ipv4 option. And there is the problem - the device cannot get the setting via DHCP. The firewall is adjusted properly by NM, dnsmasq is started. I've looked at dnsmasq arguments string and found that the temporary config file which is provided by NM is empty. So, where else should I look for a possible reason or should I just post a NM bug?
View 6 Replies
View Related
Feb 22, 2011
I just installed F14 today, all day I have been trying to get my wifi to work, I keep running in problems I found many threads with links to download drivers. I did that and in the README file loses me. It talks about compile driver from the source code.
PHP Code:
View 7 Replies
View Related
May 15, 2011
Fresh install of Fedora 14 from Live cd.Used it for an hour or so, d-loaded some programs, had ti all running great. Wired connection to internet. Had the Network Connection Manager icon in panel. There was an icon saying new updates, alot of them, like 400 or so. Told it to go ahead and up date, left room. Came back hour later was done, said it needed to re boot, so I did. From then on, no internet, not icon, no Network Connection in the drop down list for preferences.
What I have tried:Worked off live cd, again, all works fine, icon, manager, internet all there.In installed version: In terminal, typed service Network Manager, it said unrecognized service.Did yum install network manager. It started to do it, but looked like it was trying to get stuff off mirrors, and of course there is no internet access. error PYCURJ ERROR 6.Of course I can re install, but I figure I will just end up in the same place a few hours from now.
View 6 Replies
View Related
Jun 26, 2011
I have a laptop with ipw3945 on. I don't want to use Network Manager. this is my wpa_supplicant.conf
PHP Code:
[code]....
I do as root:
PHP Code:
[code]....
In another terminal as root I do:
PHP Code:
[code]...
but no IP address got.
View 8 Replies
View Related
Aug 24, 2011
does Network Manager in Fedora 15 support bridging and if so, can you configure the bridge using your wireless interface? All of the information I've come across so far said that you can NOT create a bridge using a wireless interface, and that Network Manager doesn't support bridging, but this info was also from Fedora 12 and below, so I don't know if it's still relevant for Fedora 15. I would certainly hope that by now you can make a bridge from a wireless interface. Even the lowly VMware Player offers this option.
View 2 Replies
View Related
Sep 23, 2010
I am running Fedora 13 and using Ndiswrapper with my pci wireless card. my router is a netgear wgr614v9 wireless router with wpa2-psk. When I try to connect to my network the only options I see for security are dynamic WEP (802.1x) and WPA &WPA2 Enterprise and for authentication all I see is TLS LEAP Tunneled TLS and Protected EAP (PEAP). I can connect to my network when I drop security on the network but other wise I am stuck. I have been trying to fix it for about a week now by myself to no avail
View 6 Replies
View Related
Aug 30, 2011
I'm a new fedora-user and are having some problems setting ut everything as i want:
The host to always use WIFI
The host to not see the ethernet-connection.
The guest to use ethernet
The guest to be able to get wifi when no ethernet is avaible.
The guest to install from PXE
The guest is going to be a Windows 7. Nothing is done so far, as i cannot figure out how to do this.
View 1 Replies
View Related
Jul 3, 2009
I'm currently on F11, and experienced problems with Network Manager. Whenever I to connect to a network, wired or wireless, it just seems to try to connect, and then after 2-3 seconds, it just reports "Disconnected"..
Then I switched to network, and both wired and wireless works. so I don't think there is any driver or hardware issue...
Does anyone have any idea of this problem? The network manager have worked on the live CD version ( before installed to HD).
View 12 Replies
View Related
