I just installed 11.04 on my Dell Latitude D620, and I'm not able to get an Ethernet connection. (Which in turn means I can't get wireless drivers.) Whenever I plug in an ethernet cable to the port and select auto eth0, the networking icon on Ubuntu's status bar flickers between the obtaining wifi animation and a spinning cursor. In a couple minutes I get the "wired network - disconnected" message.
View 1 RepliesI'm using Dell Latitude D620 notebook,with Squeeze amd64.This is the output of lspci:
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated
[code]....
I have installed CentOS 5 just downloaded yesterday on a Dell D620. Everything but the wireless card works. So I found this article:
http://wiki.centos.org/HowTos/Laptops/Wireless/Broadcom
and followed it step by step and was able to complete all of the tasks. The problem is that obviously it still won't start. It is not even recognized as an adapter but when I run lspci -v it is there sure enough. When I look under the networking GUI it is listed there but it has no MAC assigned to it. Please let me know what command output you need to see and I'll get here asap. I have searched this forum and other sites and nothing so far has worked.
I have recently installed Ubuntu 9.10 but am unable to connect to any of the wireless networks. Network manager does not shows any of the available wireless networks and upon clicking the network connection icon, under Wireless networks category it shows "Device not ready".Following are the results of some of the commands :
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
[code]....
I've recently partitioned off a section of my hard drive to run Ubuntu from and I'm having trouble with the network connections. In my device manager of Windows 7, it lists that my network adapters are
1. DW1520 Wireless-N WLAN Half-Mini Card
2. Intel(R) 82577LM Gigabit Network Connection
Is there something I'm not doing right in order to allow me to connect to a wireless connection? Are these devices even enabled in Linux systems?
I just did a fresh wipe and install of Ubuntu 11.04 on my Dell D630 Latitude. I installed connected to the internet and ubuntu recognized I was missing firmware and I installed and rebooted. Now the "firmware missing" notice is gone but I don't know how to connect to my wifi. I can access internet with the ethernet cable.
This is the lspci:
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c)
00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (primary) (rev 0c)
00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (secondary) (rev 0c)
[Code]....
I feel like I just need to add the wifi network, but I don't know what info to put into the fields.
I've installed successfully the ubuntu 9.10 netbook remix on my DELL Latitude 430.Everything work out of the box except the wifi, I cannot find a way to get working.Using the lshw command, I can see that the interface is listed, but status is disabled.On the Network Manager, status I get is device not ready.As a FYI, bluetooth seems working perfect (I've not tried to pair with any device)as this is the only roadblock I face before enjoying Ubuntu on my laptop.
View 6 Replies View RelatedHave an odd problem on a Dell Latitude 13 w/ a Intel WiFi 5100 card. The wifi antenna is disabled on startup into Ubuntu 10.04/64-bit. There's no hardware enable/disable that I can find.I have tried "sudo ifconfig wlan0 up" to enable it, the light for the wifi antenna comes on, but still no luck.I know the wifi works in Ubuntu, because if i load windows first, then reset into Ubuntu, once in a while it works just fine.
View 2 Replies View RelatedI have a 10 year old Dell Latitude CPx that has no ethernet or modem ports, and the only way to connect to the internet is the Dynex Wireless G DX-BNBC PCMCIA card. It came with Windows 98, and I put Xubuntu on it for a while. I believe it was Xubuntu 8 or 9. Back then I had no clue what to do whatsoever, so after a couple weeks removed it and put Windows 2000 on it. It worked, I used it for a while, but it was slow and 2000 took up a lot of space on the 12gb hard drive after all the updates. I left it forgotten and gathering dust for the past year.
Then a few days ago I discovered Lubuntu 10.10, and from what I've seen so far it is definitely a lot more compact and faster than 2000. However, the wireless card still won't work. It's somewhat recognized, because whenever I unplug it and plug it in a bubble pops up saying "you've been disconnected from the network"... which is odd, since it never says I'm connected, and says that the firmware is missing for this card. Anyway, I discovered something this time. By running "lspci -nn | grep -i 14e4":
[Code]....
I am running the latest version of arch linux on a Dell Latitude D420. So far everything has worked perfectly except the wireless. It seems that Arch does not even detect the wireless because ifconfig -a only gives me the loopback and eth0. I installed ndiswrapper as well as the drivers. lsmod | grep ndiswrapper shows that ndiswrapper is being loaded on boot. I tried to install the iwp3945 drivers, but they have become obsolete so pacman was unable to find them. I also tried installing the iwl3945 drivers as explained here [URL] but still no luck.
View 14 Replies View RelatedI have been running 32 bit karmic (and before that jaunty, intrepid and hardy) with no problems on my Dell D620 laptop. Since I upgraded to lucid, I get occasional freezes. It often happens at the gnome login screen after I click on my name but before I can enter the password, or upon restore from suspend but sometimes at other times. It doesn't happen all the time but often enough to be really annoying. When the freeze occurs, the mouse pointer responds to the touchpad or an external usb mouse, but no mouse button events are recognized and the keyboard has no effect either. I can't switch virtual terminals or anything. If the system was up and had a DHCP address at the time of the freeze, I believe the network still responds to ping. The only thing I can do to get the system back is hold the power button for 30 seconds until it powers off. The desktop CPU temperature monitor does not indicate excessive heating at the time of the freeze. I don't know whether I should try a re-install of lucid, or just go back to karmic.
View 4 Replies View RelatedI have a Dell latitude D620, suspended to ram and resumed and when I move the mouse the display goes crazy. It looks like an old TV with the horizontal hold messed up. IIRC this runs an intel video card, I'll double check when I get home.
View 1 Replies View RelatedHi,I'm using a Dell Lattitude D620 laptop. I just installed the latest kernel 2.6.38 in my Squeeze amd64 :
Output of uname -r
2.6.38-bpo.2-amd64
Now I'm running on new kernel,everything seems fine except my wifi ( now I'm connected through ethernet ). Before I do the process with the guide in http://wiki.debian.org/wl to activate my wifi,I'd like to ask for some advice here,is this latest kernel support my wifi card? If yes,how to activate it?
Output of lspci :
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03)
[code]....
am running ubuntu 10.10; Laptop see others network but its can't connect to my network. This card work under Windows XP.
View 1 Replies View RelatedI am running (K)Ubuntu Lucid 10.04 64bit on a Dell Latitude E6400, WiFi Card Intel 5100. Never had any problems with networking. Up to about 2 weeks ago. I do realize there have been quite a few posts with this network adaptor, but non really described the problem I have here.
What happens is that suddenly the WiFi LED on the computer stops blinking, the WiFi connection gets disrupted, and the device is not recognized anymore when checking ifconfig. Only cold restarting the machine helps then... it will work for a while (between 1 and 20 minutes) and then crash again.
On Windows 7 the card works perfectly fine. With Ubuntu 11.04 in Live CD mode I have the same effects (connection crashes after a while). Also tried booting an older kernel, no success.
My exact hardware:
Code:
I notived the following problems in /var/log/kern.log
Code:
I just received my brand new E6410 laptop, which have i5 processor and wish to install ubuntu 10.04 on it.
I am wondering which should I choose: 32-bit or 64-bit?
I resued a Dell Latitude CPi D300XT that was getting tossed and have XP on it running a little slow but decent for basic web surfing. I saw a ..... video of someone that had Ubuntu Minimal with LXDE running on it. I could not find that but tryed Puppy Linux, Damn Small Linux, and Ubuntu 9 to 11.04 CD's in it and could not get them to to boot into the CD. I even just set the Dell to only boot from CD/DVD and would not boot any of them.
Does anyone know which Ubuntu or Linux distro I could try on a Dell Latitude CPi D300XT? The specs are Intel Pentium II 300 MHz, 256MB of RAM and 20 Gig Hard Drive.
refer to this and let me know if I can get this working
[URL}
I'd really like to start using Linux, but I don't know much about it. I tried installing Mandriva One 2010, but it apparently isn't compatible with my laptop. Does anybody know what would be a good distribution to use with an old Dell Latitude CPx? I'd like to get a free bootable CD one for starters, if possible. I mainly would like to use it for surfing the Web.
View 9 Replies View RelatedNew to GNU/Linux community. Have Dell Latitude C800 I picked up for $5.00 @ garage sale. Windows XP currently installed works fine, but looking for optimal Linux OS for this unit. Tried installing SUSE 11.2, Gentoo, Freespire, Debian, Vector, Knoppix & Ubuntu w/o satisfactory results. Any suggestions from you good folks w/experience? I understand Slackware might do the trick, but remember I'm a newbie. :-)
View 5 Replies View RelatedAfter someone messed up the computer by putting XP half ass on it, it was built for windows 98 se. Now that i am working with an unformated hard drive. It doesn't like Ubuntu, Kubuntu, Windows NT, so I need to start somewhere and I need the answer fast, so i need to know what is the best linux distro for it. it is a Dell Latitide CPT c.
View 8 Replies View Relatedwe have a laptop (dell latitude xt) on our company, and we would like to install ubuntu on it. windows 7 works fine out of the box, so the hardware is fine.since this laptop has a touchscreen we just installed ubuntu 10.10 netbook edition 32x.But, we do not manage to enable the touchscreen, neither the vga graphic drivers.
View 1 Replies View Relatedthis is my first post sorry if im not clear OK i downloaded Ubuntu 9.1 32bit burned it to a CD and popped it in my dell latitude c600 i was going to set it up to dual boot with xp i already have 2 partions so every thing was ready
i hit install and saw a Ubuntu symbol fading in and out after that i got a whole heap of i/o errors ranging from 350 to 500 for the first number, then a bit later it loaded up the busy cursor for Ubuntu on a black screen it then changed to a cross outline and no matter how long i let i go for i do not change at all off that the disc isn't the problem because it works on my desk top live and install
I have recently installed Ubuntu 9.10 in my Dell Latitude E6400. Everything works great except that I cannot disable the built in microphone. I have even disabled from the BIOS but the mic continues working, this is really annoying as I do lots of calling from this computer for my work.
I have played around with the alsamixer and the sound preferences but I haven't been able to disable it or at least lower its volume.
My headset is plugged in to the mic jack and it works fine. The problem is that both the headset and the internal mic are working at the same time.
The disc is fine I have installed using the CD on an Acer Laptop without any trouble what so ever. However now I need to install it on a Dell Latitude D505.It was detected and started the disc and show Ubuntu with the five dots loading screen. And then it goes black, with the laptop on. The menu with options like Install, defect test etc. can't be seen.In response to this I installed it inside Windows and that seemed to be ok, so I restarted the laptop and selected Ubuntu from the boot menu and does the dot loading screen and then black.I have searched Google and it is just threads that end up dead.
View 9 Replies View RelatedI've installed Ubuntu 10.10 Netbook to my sisters laptop (Dell Latitude C640) but there appears to be a problem with the screen going black then opening the primary window, then loading the sidebar and then going black again.
For example, I'll hover over the new bar on the left and it'll just disappear, the screen will go black then will suddenly come to life again and then disappear, go black and so on. It just cycles through that.
Am pposting in here cause its my understanding gos is a part of the ubuntu family sorry if i am wrong. Anyway i have a dell latitiude d610 which am wanting to run Gos on currently i dual booting but keep finding myself going back to windows as I cant get my wireless working in gos any ideas please anyone
View 4 Replies View RelatedI'm trying to install the magnificent ubuntu 10.10 on my brand new Dell LATITUDE E5510. The installation works fine. I installed it with a working internet connexion ... so the drivers should be there. Then when booting, the GUI does not start I get the console instead...
I tried several things:
- run startx --> I get a blank screen where even CTRL+ALT+F1 does not work anymore
Code:
sudo dpkg-reconfigure -phigh xserver-xorg
--> just returns without anything on the screen, no error no nothing
- run in failsafeX mode, I get:
Ubuntu is running in low graphics mode. Your screen, graphics card, and input device settings could not be detected correctly. You will need to configure them yourself.
Then I get the login page but it doesn't go any further, when I type my login/password it comes back to the login page...
When I do:
Code:
lspci | grep VGA
I get :
VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev02)
That's all I could see... apart from that I'm not getting any error messages and I'm really stuck.. I'm running on intel Celeron 32 bit, I have checked the checksum of my CD...
Partitioned Hard Disk I set up Ubuntu 9.10 (10.4 would hang before installation).Computer works for a few minutes and then freezes (pointer and the rest: Ctrl Back, Ctrl Del, Ctrl f2 do not respond).The graphics card is Intel� HD GraphicsRAM 8GbHD 500GbLED Display (1920 x 1080) (perhaps too much?)It seems a memory problem:testing memory on windows is ok. On Linux the memory test declare "too small lower memory". No problems with windows (I tried also wubi, independently, but it hangs immediately going blank after upgrading packages). Ubuntu 9.10 works perfectly on my older pc
View 3 Replies View RelatedA friend lent me their Ubuntu book but I can't understand it and could not find anything about the sound suddenly going from the speaker on Monday night. I went to Sony Ericsson's site to check something on my account and loud music suddenly started blaring out so I pressed the Fn button and End which muted it. However, I forgot to take it off before closing down for the night and as of Tuesday morning I have no sound. Would me leaving mute on all night have screwed something up or has it just suddenly gone? I am so upset as I cannot afford to get another laptop as not working and this is my last resort since my original Compaq one died.
I appreciate any "Helpful" solutions. Not in techy but layman's terms please as I won't understand. Also if you do reply, I am in the UK and also don't get notifications so I am not being rude if I can't get back to you quickly. I will be going to bed now.