Ubuntu Installation :: Lynx On Dell D620 Hangs And Freezes Since Upgrade ?
May 11, 2010
I have been running 32 bit karmic (and before that jaunty, intrepid and hardy) with no problems on my Dell D620 laptop. Since I upgraded to lucid, I get occasional freezes. It often happens at the gnome login screen after I click on my name but before I can enter the password, or upon restore from suspend but sometimes at other times. It doesn't happen all the time but often enough to be really annoying. When the freeze occurs, the mouse pointer responds to the touchpad or an external usb mouse, but no mouse button events are recognized and the keyboard has no effect either. I can't switch virtual terminals or anything. If the system was up and had a DHCP address at the time of the freeze, I believe the network still responds to ping. The only thing I can do to get the system back is hold the power button for 30 seconds until it powers off. The desktop CPU temperature monitor does not indicate excessive heating at the time of the freeze. I don't know whether I should try a re-install of lucid, or just go back to karmic.
View 4 Replies
ADVERTISEMENT
Jul 8, 2011
I just installed 11.04 on my Dell Latitude D620, and I'm not able to get an Ethernet connection. (Which in turn means I can't get wireless drivers.) Whenever I plug in an ethernet cable to the port and select auto eth0, the networking icon on Ubuntu's status bar flickers between the obtaining wifi animation and a spinning cursor. In a couple minutes I get the "wired network - disconnected" message.
View 1 Replies
View Related
May 5, 2011
I have a Dell latitude D620, suspended to ram and resumed and when I move the mouse the display goes crazy. It looks like an old TV with the horizontal hold messed up. IIRC this runs an intel video card, I'll double check when I get home.
View 1 Replies
View Related
May 9, 2011
Hi,I'm using a Dell Lattitude D620 laptop. I just installed the latest kernel 2.6.38 in my Squeeze amd64 :
Output of uname -r
2.6.38-bpo.2-amd64
Now I'm running on new kernel,everything seems fine except my wifi ( now I'm connected through ethernet ). Before I do the process with the guide in http://wiki.debian.org/wl to activate my wifi,I'd like to ask for some advice here,is this latest kernel support my wifi card? If yes,how to activate it?
Output of lspci :
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03)
[code]....
View 4 Replies
View Related
May 23, 2011
I'm using Dell Latitude D620 notebook,with Squeeze amd64.This is the output of lspci:
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated
[code]....
View 2 Replies
View Related
Jan 20, 2011
I have installed CentOS 5 just downloaded yesterday on a Dell D620. Everything but the wireless card works. So I found this article:
http://wiki.centos.org/HowTos/Laptops/Wireless/Broadcom
and followed it step by step and was able to complete all of the tasks. The problem is that obviously it still won't start. It is not even recognized as an adapter but when I run lspci -v it is there sure enough. When I look under the networking GUI it is listed there but it has no MAC assigned to it. Please let me know what command output you need to see and I'll get here asap. I have searched this forum and other sites and nothing so far has worked.
View 1 Replies
View Related
May 1, 2010
I am planning on playing with the lynx on VirtualBox for a while just to do some test and maybe update my installation notes before moving everything but just can't get it to work.
Environment details:
OS: 9.10
Kernel: 2.6.31-21-generic
Machine: Compaq Presario B1200, 3 GB RAM, 14 GB available disk space
VirtualBox: VirtualBox OSE 3.0.8_OSE r53138
Problem: After starting up the virtual machine and reaching the purple screen (where a keyboard and accessibility icons are displayed at the bottom part), everything just goes black with an un-blinking cursor on the top-right. I already tried recreating the virtual machine, removing and creating a number of times, and I've also tried reinstalling VirtualBox but the problem still persists.
View 4 Replies
View Related
Mar 23, 2011
Can I upgrade lucid lynx kernel from 2.6.32 to 2.6.38? If so, how do I do it from command line?
View 8 Replies
View Related
Jun 3, 2011
I just got a new dell 15z and it hangs on the install "Waiting for hardware to initialize"of the 64bit fedora. I have tried both the nomodeset and noprobe and still to no avail. I have also tried installing ubuntu and the installer will not run so im at a loss. Any ideas from the fedora community.Is there any way I can debug anaconda so I can see where it is hanging?
View 2 Replies
View Related
Dec 11, 2010
I've been attempting to install 32-bit Ubuntu 9.10 on my Dell Studio 1749 with the intention of making a dual-boot system. Attempting to install with a live CD using the default settings, I got as far as pressing ENTER on "Install Ubuntu" before the screen went completely black. The CD drive spun wildly, but nothing ever appeared on the screen. I tried the fix detailed here:
http://bennybeta.blogspot.com/2009/1...udio-1555.html
typing "nomodeset" as an option, and using the "apic=off" option. When I did this, I was no longer greeted with a blank black screen, but instead with a blinking cursor, but the installation still hung. The keyboard was unresponsive and I could not open a terminal. I also tried using the alternate installer instead, and got the same results.
After this, I tried installing using wubi, and on boot I get exactly the same results: black screen without "nomodeset" and a blinking cursor otherwise.
I should also mention that the same thing happens for every option on the installation screen, including the option to "try ubuntu" by booting from the CD.
Does anyone know what could be causing this issue, and how I might install ubuntu on my machine?
View 1 Replies
View Related
Apr 16, 2011
I'm currently trying to install ubuntu but the installation process hangs on the second page of the installation (right after select language) I am booting from a usb. NO other OS is installed and I'm currently in "try it now" mode.
View 4 Replies
View Related
May 2, 2010
I learned yesterday that doing a massive upgrade on my system while moving was a BAAAD idea.The upgrade process was going along just fine, it was all downloaded and was actually installing that last time I saw it. I unplugged my laptop to move a bookcase out, and completely forgot to plug it back in. After I got back from moving a load, I found my computer was off. I tried to boot up, and I got an error that kind of freaked me out. It reads as follows:
Code:kernel panic not syncing vfs unable to mount root fs on unknown-block(0,0)I'm able to get to grub just fine, and my windows partition loads up just fine, but any of the linux kernels fail similarly when I attempt to load them.I'm sure that I can fix this, I just have no idea how. Probably has something to do with a live cd.
View 3 Replies
View Related
Dec 10, 2010
I have Dell Vostro laptop with Core2 processor 1.8 GHz, 2 GB RAM. I want to install Fedora. I tried to install it with Fedora_14_ 32 bit and Fedora_14_ 64 bit. After booting by DVD or USB, I get initial blue screen in which I select Install and it starts for few seconds and freezes there, it does not move ahead. I got Fedora 32 bit DVD from Fedora so it should have come with checksum checked. So IMO DVD is ok, it is something else with regard to hardware detection, stopping installation to go ahead. I tried 3 times, but do not go ahead.
View 4 Replies
View Related
May 20, 2010
When I try logging in using any user name, ubuntu just returns to the login screen. I cannot actually log in. I used the recovery mode to create a new login with password 123456, and the same thing happens. What could it be? Ubuntu worked just fine for a while, then DKMS started causing problems, I had errors with upgrades, software installs/uninstalls, then my sound went. I found a great fix for the sound (https://help.ubuntu.com/community/SoundTroubleshooting), the sound came back, but then I could not log back in again. I cannot find any help for this issue, and had to install 9.10 Karmic Koala, and that's what I have been using for the past couple of days.10.04 has been fairly buggy for me and I am considering staying with 9.10, or going to another Linux distro.
View 7 Replies
View Related
May 21, 2010
I recently installed ubuntu 10.04 lts. Whenever i boot ,it hangs the moment i log in. I had the same problem with 9.10 as well.
View 1 Replies
View Related
Mar 24, 2011
I just installed debian-6.0.1a-i386-netinst yesterday on my Dell Dimension 4100. I have a serial keyboard and mouse, which both worked fine during the install and the keyboard allowed me to enter the correct passphrase. After I enter the passphrase the PC continues to boot up, and it gets to a black screen with small fuzzy/distorted "DELL" logo's on the top part of the screen going from left to right.
What is wrong with my PC? What can I do to troubleshoot this?
I really would like to get debian up and running on this desktop
View 5 Replies
View Related
Jun 24, 2009
I upgraded from FC10 to FC11 yesterday.I had no problems using FC11 after I looked into the bootloader (not intuitive - Ha!).Tried to boot up this morning; and things seemed to work well until I tried to call up Firefox (added a few themes yesterday).The window pops open; but the computer freezes on the spot with an alarm (generic "beep", w/o the finishing "p").Tried it with Epiphany; and I get the same results with the exception of actually getting to the Home Page.Yum works for the most part - I reinstalled Firefox (no effect); but couldn't reinstall epiphany (keeps saying "there is no such package - did you mean 'epiphany'". No typos on my part - go figure). Doing Software/Package Updates (via System Menu) freezes the box as well.Did it with the system monitor on. It doesn't appear to be related to CPU Usage.
Had a FC10 liveUSB and used it for awhile (e.g. to check out the forums). After giving my ISP some grief about downloading speed, immediately received a note from their Abuse Department, saying that my machine had been infected with a virus and had been sending spam emails (post upgrade to FC11).
View 14 Replies
View Related
Sep 18, 2010
I'm running Ubuntu 10.04 Lucid Lynx Desktop Edition and most of the time I get these random freezes and then I have to turn off my computer and reboot it back on. It's getting really annoying because I am constantly downloading huge packs of data and it freezes and then I have to start re downloading...
View 2 Replies
View Related
Nov 2, 2010
I purchased a USB from [URL] for the upgrade of the title. There are no instructions so I need to know how to do this upgrade. I have looked at the files on the USB and it is not clear how to proceed.
View 5 Replies
View Related
Mar 24, 2011
I am currently running Ubuntu9.04 (Jaunty) on a Dell Vostro v13, pre-installed when I got it. I would like to upgrade to the 10.04 LTS but when I try, all goes fairly well until I get to the screen where it wants to set up my keyboard (Step 3). Then comp freezes and I have no use of touch-pad or keyboard, have to just shut off computer and re-install to factory settings to use it again. I have upgraded with USB and through update manager. Neither works. No clean instal from a CD because I don't have a CD drive... I have read in a couple places the inability to use keyboard/touch pad might have to do with the incorrect driver on the VostroV13.
View 2 Replies
View Related
Aug 12, 2010
I was running Ubuntu 9.10 on my Toshiba A40 Laptop and decided to take the plunge and upgrade to 10.04. Everything seemed to go well until the Restart. Now it only gets to the Splash Screen (Purple Screen with "Ubuntu" and dots under it) and then there is a flash and the text becomes blocks briefly before going to a blank screen! It seems like it might be a video problem but...
View 1 Replies
View Related
Nov 27, 2010
Recently I decided to upgrade my 10.04 installation the lazy way, by clicking the upgrade button instead of a clean install (32bit). Now, I can only get into Ubuntu with the recovery mode. If I let the system boot the normal way, I end up at the login screen where I (correctly) enter my password and then nothing else happens. I can move the mouse, the clock ticks on, and I can even use the restart button, etc. But the login screen stays gray and does nothing else, so no desktop. With recovery-mode I can use the failsafeX option to get into the desktop, everything works fine there. And even though it calls it a low-graphics environment or so, everything looks normal, its even my native resolution of 1440x900.
My first idea was some driver issue for my Ati Radeon HD 2600 Mobility card, so I looked into that. I've checked/done the following:
- Installed the drivers manually (downloaded from AMD)
- Uninstalled those drivers
- Used aptitude to remove any fglrx things
- Installed Jockey
- Installed the drivers with Jockey
- Removed the drivers with Jockey (Ive read this is the cleanest option)
- "no drivers" at this point
- Use generic/default X config, make specific X config (both from the failsafe X boot thing)
Nothing worked at all, booting still only works with recovery option and then the low graphics mode. Otherwise, it will just "hang" on the login part. When I boot first recovery mode, and then pick the resume option, I'll see some errors near the end of the booting process.
I've seen 2 errors which might be related to my issue:
- "Unable to allocate crypto cipher with name [ecb(aes)]" (home is encrypted, and accessible with safe boot)
- BUG: CPU#1 stuck for 61s!
Now, the second error seems to "match" with hanging at login. I login, something is stuck and churns the CPU... and never gets unstuck, so login just hangs there. However, I can't find any information related to that stuck CPU thing. Only changing PIDs and other numbers/stack traces, no processname or any other name to work with. So I'm at a loss here.
Big dump of possibly interesting part of kern.log:
Code:
Nov 26 20:31:25 lexmortis-laptop kernel: [44.572381] BUG: unable to handle kernel NULL pointer dereference at 00000021
Nov 26 20:31:25 lexmortis-laptop kernel: [44.572386] IP: [<c027c1b0>] sysfs_delete_link+0x30/0x70
Nov 26 20:31:25 lexmortis-laptop kernel: [44.572397] *pdpt = 0000000035f29001 *pde = 0000000000000000 .....
Despite that with low graphics mode everything works, it seems to be a non-graphical issue here (stuck CPU on some process?). Unless I missed another option I can test for the graphics / drivers. ow I could find more info on stuck CPUs during boot?
View 1 Replies
View Related
Sep 2, 2010
I have been using UBUNTU 8.04 with my Dell Mini Inspiron. How can I upgrade it ? If I upgrade is there problem after upgrade ?
View 5 Replies
View Related
Mar 14, 2010
After successfully upgrading from 8.04 to 8.1 (where even my wireless worked for the first time) I got a system freeze when I tried to upgrade to 9.04.
I suspect the graphics driver but don't know how to upgrade without X running. After booting in generic mode (kernel 2.6.28-1 I can log in the shell but am lost without the GUI.
View 2 Replies
View Related
May 28, 2010
Today I upgrade my Ubuntu 9.10 pc to the latest Ubuntu 10.04 LTS. The upgrade went perfectly with no errors. But when I login to my account Ubuntu loads but then the screen freezes and nohing happens. Then I am just left with a blank desktop with only the Ubuntu 10.04 background and no panels.
View 2 Replies
View Related
Jul 19, 2010
Yesterday I upgraded from 9.10 to 10.04 (32 bit). Everything seemed to go well with no errors until the point where the system needed to restart at the end. After it restarted (and every power cycle since), it gets to the "ubuntu" screen with the moving cycle of square dots underneath, and stays there for ever. The screen resolution is absolutely goofed up, the word Ubuntu cannot be clearly read (looks like it is way overdriving the monitor). All letters seem to have like vertical bars on either side.
Below the Ubuntu and the dots, there appears to be two lines of completely illegible text (they just look like multicolored boxes about the size of characters.
I tried using the shift key to get to grub and try to boot into recovery mode--no luck. I tried using grub to boot to the previous kernel--no luck. It just sits there at the Ubuntu screen with this weird resolution/appearance.
I can boot from the Live CD and things work fine. I can see the file system, grub files etc. Any help debugging this would be most useful.
View 3 Replies
View Related
Dec 10, 2010
Today I decided to do the upgrade from 10.4 to 10.10. Unfortunately the upgrade has frozen for the last few hours (after it has completed ~60% of job)... The problem is with xorg, when I log through ssh to the computer I see the xorg process takes 30%. what I could try not to 'smash' the OS... I am not an expert. During the upgrade I have experienced only 1 error with no space left on the device (it exceeded the estimations) but I have freed additional 2GB and it continued for some time.
View 3 Replies
View Related
May 3, 2011
I just tried to upgrade from ubuntu 10.10 to 11.04 (64bit). Everything went fine until the machine tried to reboot. Now it stops while booting on the screen where the ubuntu logo and five red dots appear. I'm unable to open a terminal (alt+ctrl+f1 does not result in anything) and the only thing I've been able to do is to reboot the machine.
If I reboot by pressing ctrl+alt+delte I see some information for a short while, it seems that the boot stops on "checking battery state" I've googled this, and it seems that quite a few other have had the same problem, but they have been able to open a terminal, any ideas on how I can do this? Or any other suggestions on how to fix this?
My system is a dekstop with a Nvidia GTX 260 graphics card. I recently installed the newest Nvidia driver. I forgot to mention that I did an online upgrade.
View 8 Replies
View Related
May 24, 2011
Screenshot attached. System itself is fine as in i can move the window around, etc no problem but the upgrade itself just hangs. Left it for 20 mins with no progress.....
Anyone got any clue as to how to fix or a work around? I dont know if its related but I just upgraded from 10.4 to 10.10 and am now trying to upgrade to 11.4
View 2 Replies
View Related
May 24, 2011
Just wanted to upgrade my desktop computer and after the terminal shows:
Installling new version of config file /etc/apparmor.d/usr.sbin.cupsd ...cups start/running, process 7944
The display froye, mouse does not move any more, keyboard does nothing, no chance to escape into a text terminal. Nada. After rebooting the system I get a kernel panic. This is now second of two upgrades to 11.04 that failed, and I do not know how often upgrades failed previously, but rather often.
View 1 Replies
View Related
