I've followed a few different steps to try and solve the wireless issue, but no luck so far. I have a Compaq Presario CQ60 with Atheros 5001 "ath5k" driver and module. I use "WPA & WPA 2 Personal" security.I first did "rfkill list all" to see what was being blocked, and at the time, I had this:Quote:
0: hp-wifi: Wireless LAN
Soft blocked: no
Hard blocked: yes
[code]....
I spent days trying to figure out how to get my atheros AR928x 802.11n wireless card to work in Ubuntu. The card worked perfect in Windows 7 but the connection kept dropping in Ubuntu. It would find my router and connect with 60% signal for about 5 seconds, then fall down to about 25% signal and then cut out altogether. After searching for days to find a solution, I finally figured it out and figured Id post it here to let everyone else in the same boat have a working wireless too!
I found this solution from:[URL].. This solution is for JAUNTY (Ubuntu 9.04), so if you are running Jaunty, you can just follow that post. If you are using Karmic (Ubuntu 9.1), you can follow this tutorial I'm posting. It's pretty simple: First, make sure you got all your files up to date. Type in a terminal:
sudo apt-get update Let that run, and once its done, type into terminal:
sudo apt-get upgrade
Once that finished, restart your computer. Again open up terminal and type:
sudo apt-get install linux-backports-modules-karmic
If you are using Jaunty, instead of karmic type in jaunty, if you use another version of ubuntu, you can find a list of versions and their names here:[URL].. Restart your computer one more time, and you should be good to go! This has been tested and confirmed to work on: -Ubuntu 9.1(karmic) with an Atheros 928x 802.11n wireless card, using the Ubuntu installed network software, in a Gateway NV53 laptop connected to a belkin 802.11n wireless router.-HP base station / 802.11g airport express
This has been tested and does not work/has issues with:
-airport extreme I hope this works for you too, and if it does, please let me know with your hardware and Ubuntu version so I can post here what other setups have been confirmed to let this work.
Does Ubuntu 10.04RC support Atheros AR2427 wireless card out of the box? I ran 10.04RC Netbook Live on my new Asus Eee 1001P Netbook today and it looks very impressive indeed. However, I could not get Ubuntu 10.04 to even see the Etheros AR2427 card (iwconfig). Am I doing something wrong or is there no driver to support the card? If no driver what are my options to get it working under 10.04 as I do not want to use Windows on my netbook..
View 4 Replies View Relatedlspci gives this for my ethernet hardware:
[Code]...
I have tried installing "linux-backports-modules-wireless-2.6.32-22-preempt" but I receive a notification that it failed to install properly upon rebooting... I have also tried installing compat-wireless but it fails to make because it can't find the linux kernel header directory...(I do have the headers, but how do I get the makefile to see a non-default header dir?) sudo modprobe ath9k runs, but running sudo ifconfig wlan0 up returns this error:
Code:
sudo ifconfig wlan0 up
SIOCSIFFLAGS: Unknown error 132
I just installed the new version of ubuntu 10.10 and I discovered that my wireless card atheros ar5001 is not working, i tried to modprobe ath5k and wont work either.
All the past versions of ubuntu had no problems. bug?
I'm using a compaq cq60 laptop.
I upgraded to Maverick Meerkat on my Compaq Presario CQ60 and the installation bugged killing all the documents and settings. I'm not a total n00by to Linux as I've been using it for years, but neither am I an advanced user.
Any halp you can give with this as I've tried everything I can think of to get the wireless card to work. Which basically boils down to trawling Google for the drivers and attempting to install them. code...
I have a Toshiba MX35 laptop it's a little old but does the job. I'm have a problem getting the wireless to work. I can boot a live CD either Ubuntu 10.10 or Fedora 14 and they will see the wireless card. The card is Atheros Communications Inc. Atheros AR5001X+ Wireless Network Adapter (rev 01).
I have Ubuntu 9.10 installed and that is the OS that is having the problem seeing the wireless. The computer will not handle Ubuntu 10.10 (at least it won't handle the desktop effects under Ubuntu 10.10) but handles them just fine under 9.10 and that's why I have 9.10 installed. I really need the Wifi to work because I'm going to travel in a few days.
So I decided to wipe out Windows and try Slitaz. It's an awesome well featured distro for it's size. One huge problem tho: I can't get wireless to work for the life of me. I actually went as far as to manually load the ath5k module but It just refuses to recognize my wireless router, much less any nearby routers. It simply doesn't see anything when it scans for wireless networks. I have no problem with that in Puppy Lucid. But I'd really like to use Slitaz, just for it's small size and quick bootup. Can anyone PLEASE help me with that?
PS: It happened here before that I had to plea and beg for any response, so PLEASE(!!) don't let me hang like that this time.
Cannot get wireless to work. Hostapd.conf had nothing inserted in it so I put the following in which I found [URL]..So it connected right away and then disconnected after opening one of my tabs. I went back into hostapd.conf and it had erased all the info I put in there. Is there a way to keep it from deleting this info every time. Because it worked great for a brief second. Otherwise it just keeps going on, then going off. It stays off most of the time though. Right now this is what my iwconfig reads:
[Code]...
Hope this saves some1 an immense amount of time;First type this;
Code:
rfkill list
check if the problem looks like this
[code]....
After an upgrade to 2.6.27.25-78.2.56.fc9.i686 in March, my Atheros wireless stopped working. (It had previously run without a hitch for 9 months). Anyway, I finally got around to working on it today and using the "WiFi misery" thread managed to consistently get it to start manually via these steps:ifconfig wlan0 up
iwconfig wlan0 essid netname key xxxxxxxxxxxxx
click on "activate" in network device control (gives error msg, but works)
During boot-up, I get "Invalid argument" errors for "SET MODE", "SET BIT RATE", and "SET ENCODE".Currently NetworkManager service is disabled, but when enabled doesn't seem to change any of the above.I'd like to get back to automatically coming up wireless, if possible.
I have an Atheros AR5007 802.11 b/g WiFi Adapter. I use OpenSuse 11.3, KDE desktop.When I did iwconfig, it displayed the following:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:"sami"
[code]....
i have a dell duo and i am wanting to install ubuntu Q. there is no LAN connection what is the "best" way to get the atheros wireless working.i have looked around for a driver to downlod found several that appear as they would work i just don't know which would be the best or the best way to download and install it?
View 7 Replies View RelatedAnyone knows what is the right driver for this device? It is not being recognized by the system, and there is no Atheros AR9271 on url
View 9 Replies View RelatedA wifi card with the ath5k driver used to work properly until a couple of weeks ago. Now, if I ping the router the response times sometimes are okay but often fluctuate into the range of many hundreds or thousands of milliseconds. Occasionally the connection breaks down entirely.My laptop, which uses a different card, works fine (typical ping response times of 2 ms), so its probably not the router which is faulty.I use opensuse 11.3 x86_64, currently with the 2.6.34.7-0.7 desktop kernel and knetworkmanager
View 1 Replies View RelatedAfter several hours of frustration to point of almost scrapping linux alltogether I was finally able to get my wireless networking to work in Linux Mint 6. I searched for hours and came up with several different suggestions that were supposed to fix my problem - NONE OF THEM WORKED! As a new linux user, I can completely understand why so many people try linux and then give up on it. It should not be so hard to get a wireless internet connection working.
Said another way - the people making distros should read these forums and see what difficulties are experienced and work on fixing them. In any event - I want to post my solution to the problem for my COMPAQ CQ60-211DX so that anyone else who wants to try linux on this model laptop will save a great amount of time. Here are the steps I took to get linux mint 6 to work on my laptop:
1. Open terminal window
2. Type - lspci | grep Atheros
3. Hit the enter key
If you see: Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01)
then these instructions WILL get your AR242x (AR5007) wireless card to work for you. Be warned - I tried everything I read including ndiswrapper, etc. - none of it worked! You will need to click the menu button go to all applications and then administration. From there, select hardware drivers and look for anything that has Atheros in it. CLICK DEACTIVATE! Now you will have to restart your computer. When it starts back up....
I got a used computer (Toshiba Satellite A215-S5829) for Christmas, and it was running Vista *shudder* so I decided to wipe the hard drive, and install the latest Ubuntu. This is my first real foray into linux, and I've loved the system, but the only problem I've had with is so far is I can't get the wireless to work. I believe the card it has is Atheros AR5001, and I've tried installing the "madwifi" drivers, but I can't get them to register. I've been following the suggestions of dozens of different forum posts and answers I've found scattered around the internet, but I haven't been able to get anything to work correctly.
When I view the "Additional Drivers" in System > Administration, it says "Alternate Atheros "madwifi" driver: This driver is activated but in use," but when I click on the internet icon in the top panel, it only gives me the wired connection. It used to also give me the wireless option, just without ever successfully finding any wireless networks to which it could connect. Like I said, I've done about a half-dozen different things without any success.
I'm trying to get bluetooth working. I have an ASUS USB-BT211 USB 2.0 Mini Bluetooth Dongle. Where do I find the driver and how do I install it? (Currently when I plug the dongle in, it is ignored.)
lshw shows me this:
Code:
Bus 008 Device 003: ID 0cf3:3002 Atheros Communications, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
[Code].....
I'm new to the linux community -started using Slax as of this morning. I'm having trouble getting wireless set up for my Atheros AR9287, I found that Compat Wireless should get the thing to start working.
Problem is I have no idea what I'm doing setting it up. Can anyone explain this to a total novice? Or have anything else that will get it to work?
I can't get my wireless into monitor mode. I;m running ubuntu 9.1 karmic It connects fine to wireless networks. But when i do: sudo iwconfig wlan0 mode monitor. I get: Error for wireless request "Set Mode" (8B06) :SET failed on device wlan0 ; Device or resource busy. I can only see wlan0 (wmaster0, eth0), not ath0 or wifi0 mentioned elsewhere, in wireshark. I only see my own ip and packets coming to and from that. my system tells me i have an atheros ar9285 chipset in place.
View 2 Replies View RelatedI bought this new computer with an Atheros AR9285 wireless adapter, signal dropped out after a couple of minutes, sometimes reconnected, I looked up different posts on [URL] and [URL].
First I installed linux-backports and linux-backports-wireless, still dropped. Then I installed compat-wireless-2.6.33 and it still dropped. Finalley I blacklisted the driver with gksu gedit /etc/modprobe.d/blacklist-ath_pci.conf and it still drops. What should I do, it seems to pick it up again after 30 sec or so, but it a bit frustrating.
P.S.: It seems to be getting much better now that I have the torrent program shut down.
I've a big trouble that curses me for months. I've an Asus K52Jc laptop with wireless card Atheros AR9285, Ubuntu 10.10 and this network set-up: a WDSL (so an antenna on my house) wired to a switch; the switch shares connection through 2 ethernets cables: one to my uncle house, one to my router Netgear DG834v5.If I connect my laptop via ethernet, internet works good, if I connect to my router, wireless works (I can ping my router), but no internet. I've been helped a lot in official ubuntu chat: after some tries we understood that the problem aren't drivers, isn't Netgear, but probably it's something messed up in routes or arp cache.Anyway note that I have also some difficulties to ping my router, on 3 tries he often loses 1 or 2 packets.
[Code]...
I installed Fedora 11 on an Acer Aspire 5516 and everything works except my networking interface card. In Windows XP it is listed as an "Atheros Ar8132 PCI-E Fast Ethernet Controller" and it works. In Fedora 11 it is listed as "Attansic Technology Crop. unknown (OX1062)" and does not work. I have tried the default driver "ath5k" and also downloaded madwifi and modprobed "ath-pci" but I still get the same problem. What is weird is that the wireless does work. Is this chip not supported yet in Linux?
View 1 Replies View RelatedInstalled 10.04 on an Acer TimelineX 3820TG but can't get the ethernet to work.
Code:
$ sudo lshw -C network
*-network UNCLAIMED
description: Ethernet controller
product: AR8151 v1.0 Gigabit Ethernet
[Code]....
The driver from [URL] won't work either (error in script on make).
After upgrading to 11.04 about six weeks ago I've had no sufficient solution to my inability to connect to wireless. Here is a summary of the problem:
After the upgrade, nm is running, and lspci detects my wireless controller (Atheros AR2413 802.11b/g), but nm can only sporadically detect/connect to wireless networks. Essentially what happens is that upon startup, I have to wait (sometimes 5 minutes, sometimes hours) for the computer to "decide" that it wants to detect the networks, at which point I can connect. After this it is fine; it doesn't disconnect after this point, but more often than not it takes so long to start working that I might as well not use the computer.
I've tried "Connect to Hidden Wireless Network", to no avail. I should mention that I also run under the Gnome Classic UI, because Unity is one of the worst UI changes I've ever seen in a version. I've read that Unity causes some problems with NM, but I have no corroborating evidence of this, and the problem persists even without using the Unity UI.
Someone recommended using an older kernel, but the file "menu.lst" doesn't even exist in the /boot/grub folder, so I have no idea how I would do that.
I've installed it no problems on my desktop and I really love it. Now I'm trying to install it on my Satellite and I'm having a couple of problems. When trying to connect to my wireless network, I can see my network, but it will just keep asking me for my WEP. I've confirmed that there is nothing wrong with the network or the password I've provided. Sometimes when I boot up, the network manager just says that the wireless networks are disconnected and can't find any. The wired connection always works just fine.
Here are the system specs:
Toshiba Satellite M45 S169
Ubuntu 10.04 Lucid Lynx LTS Fresh Install
Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01)
Kernel driver in use: ath5k
Kernel Modules: ath5k
I have an old Tatung tablet pc, with touchscreen, stupid speakers and an atheros wifi card (AR5001X+). With XP, everything works reasonably well, and wifi connectivity is rock solid. I know I'm asking for trouble installing *nix on this machine, but if the wireless worked, I'd be happy. However... With an updated Lucid install, I can see and connect to open, WEP, and WPA(1/2/tkip/aes/whatever) networks. I get good speeds with every network I've tried, but after a minute or two, my connection speed drops to zero, only to recover after another few minutes. A few minutes later, the wireless dies again, then reconnects....
Both the router and the tablet show that I still have a connection, and the connection speed recorded by both does not change from the 'working' condition. I get nothing in the logs (router or tablet) and no indication (aside from transfers stalling) that there's any problem. The 'network history' part of Gnome system monitor shows the data rate dropping to zero, but a network monitor applet on the gnome panel shows transmissions and (later) recieves. Reported signal strength remains constant, and seems to have no bearing on the frequency or length of the dropouts.
I've tried the stock lucid drivers, the lucid wireless backports, and madwifi (currently on madwifi) with no change to symptoms. I did think that it may be to do with scanning for networks (iwevent showed completed scans as the dropouts ended) so I removed network manager and tried static configuration with /etc/network/interfaces . The problems persited (although iwevent is now silent) and I am now using Wicd with no change.
lscpi:
Code:
sudo lspci
00:00.0 Host bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:00.1 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
[code]....
I see nothing toobad in these, so I ran a longer test - I bash'd a while loop to ping the router, run ifconfig and iwconfig, and spit the results into files. I concurrently ran a wireshark capture. All of these contain a lot of text/data, so I've attached them here. I can't see any connection between the output of ifconfig/iwconfig/wireshark while the ping drops, but I'm no expert.
[URL]
Ubuntu recognize my wifi adapter which is Atheros AR5007, but when i open context menu to connect to wireless network it just simply shows me that wireless is disabled and even when i checked "Enable wireless" option nothing happened. Here is information from terminal:
Code:
$ ifconfig .....
There is no any wireless device, only my wired network.
Code:
$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=off
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
Wlan0 exists but Power Management is off.
Code:
$ iwlist wlan0 scan
wlan0 Failed to read scan data : Network is down
Code:
$ sudo iwconfig wlan0 power on
Error for wireless request "Set Power Management" (8B2C) :
SET failed on device wlan0 ; Operation not supported.
Also I tried to install windows drivers with ndiswrapper but no any luck.
My system is up-to-date Ubuntu 11.04
Code:
$ uname -a
Linux linux 2.6.38-10-generic #46-Ubuntu SMP Tue Jun 28 15:05:41 UTC 2011 i686 athlon i386 GNU/Linux
I want to load Atheros wireless card to ubuntu linux OS having kernel 2.6.32.21. I have loaded the atheros driver and I observed the following log messages when card was inserted.
[ 55.732223] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
[ 55.732294] pci 0000:04:00.0: reg 10 32bit mmio: [0x000000-0x00ffff]
[ 55.810152] ath5k: disagrees about version of symbol ieee80211_free_hw
[code]....
My suspect was the driver was 2.6.35.1 kernel based i may need to update my kernel, but i have other laptop having 2.6.32-21 kernel and this card works fine.
I recently purchased an MSI 740GM-P25 with an Atheros AR8131M gigabit ethernet adapter onboard. I have since discovered that it's not the easiest device to get working in CentOS (or any other distro I've tried, frankly). Anybody use this card and have instructions on how to get it working? I've got a lot of experience with Linux, but I've never been quite as good with hardware stuff as I probably should be. I've included a list of things I've already attempted below (limited as the list may be).
1) Tried both CentOS 5.5 x86_64 and Fedora 13 x86_64
2) Tried to download and compile the source code for three different Atheros drivers from their website (the Linux drivers listed here) in Fedora 13. All stated that I was using a kernel version that was unsupported (>2.4.0) when attempting to compile.
EDIT: Also, I contacted MSI directly for assistance.I got the simple yet incredibly unhelpful "we can't help you unless you use Windows" response. So there is no official support (and therefore no driver) provided by the manufacturer.