Ubuntu Networking :: Atheros AR9285 Not Detected By Samsung NF310 / What To Do?
Nov 8, 2010
I recently got a Samsung NF310 netbook. It has a Broadcom 802.11n wireless card, which is not very well supported currently. In order to have reliable wireless, I switched it out with an Atheros AR9285 wifi card. The Atheros card seems to be invisible to the system. It doesn't show up in the output of lspci, and I can't find anything weird in dmesg. It's like it just doesn't exist.
At first I thought the card was just dead, but then I tried it out in my old EeePC900 and it works fine. I know the slot on the the NF310 is OK, because the original Broadcom card still works. I also determined that the NF310 isn't doing some BIOS weirdness to only us the Broadcom card, because my AR5BXB63 802.11g card works in it. (Unfortunately it's a full-length footprint, and the NF310 has a half-length Mini PCIe slot, so I can't leave it in there.)
The NF310 is running Maverick. The EeePC identifies the wifi card as:
I have a Samsung N150 netbook with Atheros AR 9285 WiFi card. I installed Ubuntu 9.10 on it, although this problem happens on other distros too (Network Remix 9.10, OpenSuse 11.2) My wifi card and networks get detected. The problem is when I try to connect to my network, which is protected by WPA key (I don't know if it matters whether it's WPA or not). After I input my network key, the network manager is trying to connect, but obviously cannot, because just prompts me for password again. I can connect without problems to this network from my other computer running WinXP
I bought this new computer with an Atheros AR9285 wireless adapter, signal dropped out after a couple of minutes, sometimes reconnected, I looked up different posts on [URL] and [URL].
First I installed linux-backports and linux-backports-wireless, still dropped. Then I installed compat-wireless-2.6.33 and it still dropped. Finalley I blacklisted the driver with gksu gedit /etc/modprobe.d/blacklist-ath_pci.conf and it still drops. What should I do, it seems to pick it up again after 30 sec or so, but it a bit frustrating.
P.S.: It seems to be getting much better now that I have the torrent program shut down.
I've a big trouble that curses me for months. I've an Asus K52Jc laptop with wireless card Atheros AR9285, Ubuntu 10.10 and this network set-up: a WDSL (so an antenna on my house) wired to a switch; the switch shares connection through 2 ethernets cables: one to my uncle house, one to my router Netgear DG834v5.If I connect my laptop via ethernet, internet works good, if I connect to my router, wireless works (I can ping my router), but no internet. I've been helped a lot in official ubuntu chat: after some tries we understood that the problem aren't drivers, isn't Netgear, but probably it's something messed up in routes or arp cache.Anyway note that I have also some difficulties to ping my router, on 3 tries he often loses 1 or 2 packets.
I am kind of new to linux and have installed the lucid lynx ubuntu distro (10.04) and then "upgraded" it to ubuntu studio but it still says is the lucid lynx. I got a Samsung Q430 laptop with the Atheros AR9285 wireless adapter.I have everything up and running EXCEPT my wireless card. The wireless card DOES work, it does see all the connections available, but when I choose to connect it does not, and keeps asking for the password.
Weird thing is that when I use my samsung galaxy tab as the wireless adapter for its 3G signal, it does seem to work fine (although really slow). I have tried looking for a solution, some say to just install the drivers, but ubuntu does not recognize anything to need a driver except the video card. I have installed linux-backports-modules-wireless-lucid-generic I have also tried the bleeding edge drivers.
After a while of experimenting by myself I came with the following, somewhat rudimentary. I managed to fix the problem by installing the windows wireless driver utility. Here is a tutorial on how to do it. So I just installed it, went to system/administration/windows wireless drivers and just installed it. Downloaded the file from here [URL]. It may not be the best way to fix it, but it does work. Still if you can use ethernet, don't hesitate to do it.
I'm facing problems with Fedora13 and the AR9285 wifi card... the connection is just too slow, and the wired connection works fine. I just figured out that a lot of VAIO users (so am I) were in the same situation, and solved their problem by downloading ath9k drivers from linuxwireless.org. Fine, I did it! That's what I found :
Quote:
Building and installing cd /path/to/compat-wireless-2.6.32-rc5 ./scripts/driver-select <driver-name> make sudo make install
...but make is looking for source files in /usr/src/kernels/2.6.34-7-61.fc13.x86_64/build/ , which doesn't exist! The /usr/src/kernels/ folder is just empty. I also found something about the fact that Fedora13 didn't came with kernel's source files... So how can I install that driver? (I didn't find the package via yum...)
I've been trying to install the network adapter for the ar9285 driver using compat-wireless-2.6.32.16.tar.bz2 found at [URL] The commands I run after extracting are:
cd ~/Desktop cd compat-wireless* scripts/driver-select ath9k
Then after typing scripts/driver-select ath9k. This happens:
Processing new driver-select request... Backing up makefile: Makefile.bk Backing up makefile: drivers/net/wireless/Makefile.bk scripts/driver-select: line 73: perl: command not found
installing my wireless card Atheros AR9285.I have tried to get it working with both compat wireless - Ath9k driver but I dont know exactly how to do.I have also tried to get it to work with ndiswrapper, but it is really tricky because nothing is available in centos like precompiled ndiswrapper.I used to work with Arch Linux so everything in Centos is totally new to me and I don�t understand a thing:I need to get it to work as soon as possible.What I have read the should go to just "activate" the ath9k driver with my card and it would work,
I keep getting the following error when I run the following:
Quote:
# iwconfig wlan0 key s4ssw0rd Error for wireless request "Set Encode" (8B2A): SET failed on device wlan0 ; Invalid Argument
No matter what method I try for setting an encryption key for my card, it doesn't work. I am only able to connect to wireless access points that don't use encryption.
details: I have an Atheros AR9285 wireless card, I have the mac80211,ath9k modules loaded. Also when I run lspci, my Atheros AR9285 card shows up on the list. I am using the 2.6.30.9 kernel.
I need to change my network key number in my router, because I think it is beening used by a near neighbour in the apartment above, can anyone tell me how to do this.
I have an absolutely bizarre hardware issue (concerning the Atheros AR8132 PCI-E Fast Ethernet Controller) that has been giving me quite a bit of grief for a while, and having completely hit a wall on this one, I'm a reasonably-experienced Linux user of several years, and have been running Ubuntu 9.10 on an Acer AOD250 netbook for several months out. I know that this model has wireless issues out-of-the-box (easily fixed), but it did not have any noticeable ethernet issues. That is, until I attempted an installation of Arch Linux.
During the Arch Linux installation, the ethernet card was initially detected, but unable to be used (because of a bad module in the kernel released with the installer). As I didn't know the fix for this at the time, I decided to reinstall Ubuntu 9.10. This time, however, the system failed to recognize the wired ethernet whatsoever. Instead, the external activity lights for the port (green and orange) are ALWAYS on, yet the device doesn't function.
I have done a successful install of the latest drivers directly from Atheros for the device and have them automatically loading with the kernel during boot, but as the device isn't recognized, the drivers aren't doing any good. Relevant information:
I want to load Atheros wireless card to ubuntu linux OS having kernel 2.6.32.21. I have loaded the atheros driver and I observed the following log messages when card was inserted.
[ 55.732223] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0 [ 55.732294] pci 0000:04:00.0: reg 10 32bit mmio: [0x000000-0x00ffff] [ 55.810152] ath5k: disagrees about version of symbol ieee80211_free_hw
[code]....
My suspect was the driver was 2.6.35.1 kernel based i may need to update my kernel, but i have other laptop having 2.6.32-21 kernel and this card works fine.
I have recently installed Linux Mint 10 on my laptop. When I look at the Device Manager in Windows 7, it says I have an Atheros AR9285 Wireless Network Adapter. Right now, I am unable to connect to wifi with Linux. What drivers am I able to install, and how would I install them?
Just installed CentOS 5.1 and it's not detecting my NIC. ifconfig produces nothing for eth0. This is a xen kernel.
I can't tell exactly what NIC this motherboard uses, the ASUS website doesn't seem to think we need to know anything more than that it's a PCIe Gigabit lan:
[URL]
lspci indicates it's an Atheros AR8121/AR8113/AR8114.
leopard@brokenbox:~$ ifconfig -a lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host
[code]....
I have had this issue before, and fixed it by booting into Windows XP SP3 and pressing and holding the power button down until the computer shuts down. (e.g. "Unclean or "Illegal" or "Cold" boot.) Unfortunately, not having Windows XP SP3 on my system anymore, I have to do this in Ubuntu. I have tried several times, and it is clearly not working. I don't want to try too many times more for fear of damaging my ext4 file system.
I looked for this issue on Google and found only driver problems, not device problems. There is no Ethernet option in the BIOS, except for the Network Boot, which should always show the device whether its in use or not. Is it silly to ask if Windows in a VM in an unclean shutdown may solve the problem? The driver for the device is currently supported by the kernel out of the box:
Code:
Linux brokenbox 2.6.31-17-generic #54-Ubuntu SMP Thu Dec 10 16:20:31 UTC 2009 i686 GNU/Linux
It uses/used the atl1c driver. It was working on the same install just about a day ago!
I have a Toshiba NB300 netbook that has an Atheros AR9285 wireless chipset and is running Ubuntu 10.04 Lucid Lynx. At my University there is a FreeRadius authenticated wireless network (called "UCC") that I would like to connect to. Using NetworkManager I have created an automatic profile called "Auto UCC" that contains my user details for the connection. When attempting to connect to the network, the NetworkManager icon spins for a couple of minutes and then presents me with the authentication dialog. If I re-enter my details (and disable the CA cert prompt), it repeats the process seemingly infinitely (spin-spin-spin, auth box) Attached is a copy of the syslog from first attempting to connect to stopping the connection attempts. The wireless card's 'lspci' line is
I had U10.10 installed prior to running U10.10 Desktop, and the wlan worked flawlessly on that.My understanding is that the packages are the same and so this should be installed with Desktop, however it will not action the final connection. The wlan is finding networks and prompts for the Key when connecting, but it never actually connects.
Quote: sudo lshw -C network gives the following: Quote: *-network
I spent days trying to figure out how to get my atheros AR928x 802.11n wireless card to work in Ubuntu. The card worked perfect in Windows 7 but the connection kept dropping in Ubuntu. It would find my router and connect with 60% signal for about 5 seconds, then fall down to about 25% signal and then cut out altogether. After searching for days to find a solution, I finally figured it out and figured Id post it here to let everyone else in the same boat have a working wireless too!
I found this solution from:[URL].. This solution is for JAUNTY (Ubuntu 9.04), so if you are running Jaunty, you can just follow that post. If you are using Karmic (Ubuntu 9.1), you can follow this tutorial I'm posting. It's pretty simple: First, make sure you got all your files up to date. Type in a terminal:
sudo apt-get update Let that run, and once its done, type into terminal: sudo apt-get upgrade Once that finished, restart your computer. Again open up terminal and type: sudo apt-get install linux-backports-modules-karmic
If you are using Jaunty, instead of karmic type in jaunty, if you use another version of ubuntu, you can find a list of versions and their names here:[URL].. Restart your computer one more time, and you should be good to go! This has been tested and confirmed to work on: -Ubuntu 9.1(karmic) with an Atheros 928x 802.11n wireless card, using the Ubuntu installed network software, in a Gateway NV53 laptop connected to a belkin 802.11n wireless router.-HP base station / 802.11g airport express
This has been tested and does not work/has issues with:
-airport extreme I hope this works for you too, and if it does, please let me know with your hardware and Ubuntu version so I can post here what other setups have been confirmed to let this work.
Just rebuilt my file/print server using an ECS 945GCD-M Atom motherboard. Running it under 9.10 (2.6.31-20) using the same cable and port on my Netgear switch that my old server connected to at 1GB/s without issue (old server's NIC was Intel-based).
Found the driver is an AR813x, & downloaded & installed the latest driver from here (1.0.1.9). sudo lshw -C network now shows that it's using the new driver, but still sitting at 100MB/s:
I got a used computer (Toshiba Satellite A215-S5829) for Christmas, and it was running Vista *shudder* so I decided to wipe the hard drive, and install the latest Ubuntu. This is my first real foray into linux, and I've loved the system, but the only problem I've had with is so far is I can't get the wireless to work. I believe the card it has is Atheros AR5001, and I've tried installing the "madwifi" drivers, but I can't get them to register. I've been following the suggestions of dozens of different forum posts and answers I've found scattered around the internet, but I haven't been able to get anything to work correctly.
When I view the "Additional Drivers" in System > Administration, it says "Alternate Atheros "madwifi" driver: This driver is activated but in use," but when I click on the internet icon in the top panel, it only gives me the wired connection. It used to also give me the wireless option, just without ever successfully finding any wireless networks to which it could connect. Like I said, I've done about a half-dozen different things without any success.
I'm trying to get bluetooth working. I have an ASUS USB-BT211 USB 2.0 Mini Bluetooth Dongle. Where do I find the driver and how do I install it? (Currently when I plug the dongle in, it is ignored.)
lshw shows me this:
Code: Bus 008 Device 003: ID 0cf3:3002 Atheros Communications, Inc. Device Descriptor: bLength 18 bDescriptorType 1
I realise there are a few threads of issues with the AR8152 chipset and Ubuntu 11.04, however, my issue does not appear to be the same as others, nor does there appear to be a consistent solution yet. My ethernet worked fine in Ubuntu 10.10, but after upgrading to 11.04, I experience the errors I am about to explain. I also experience these when booting off a Ubuntu 11.04 Live CD, so it's not just the upgrade the caused the issues. The issue is, if I turn on my system without the ethernet cable plugged in, and then plug the ethernet cable in once I've logged into Ubuntu, the system will not detect it, at all. No amount of network manager of dhclient eth0 will get it to function, however, the device itself still appears in the system. If I turn the system on with the ethernet plugged in, however, it will get an IP address and function correctly. I tried to download the drivers from Atheros and build them, but for whatever reason it complained about me not having autoconf.h or automake.h (can't remember which), despite having build-essentials and linux-headers-generic installed.
My old Winbook laptop had good wifi connection under Ubuntu 9.10 but shows 'disabled' under Ubuntu 10.04 and 10.10. At least under 10.10 it came up with working video (had to mess with GRUB on 10.04 before video would work). I have an onboard wi-fi card that has never worked well with any Linux as far as I know but the Atheros PCMCIA card worked solid under Karmic (9.10). Here is some diag. info.
I'm trying to tether my sprint samsung exclaim. I've tried the ubuntu network-manager and gnome-ppp. dmesg seems to show the phone connected and the cdc_acm driver loading the phone as /dev/ttyACM0 . However running wvdialconf says no modem detected.Furthermore, when I specify the device in gnome-ppp I get an input/output error.how to get tethering to work in 9.04?
I've got a little netbook, and all works fine, except for one small thing. I'm able to connect to a wireless network with my Atheros AR5001 just fine. However, if I right click on the network icon, and disable network or wireless and enable it again, wireless won't work anymore. I can't see and connect to any network at all. Except when using airodump-ng from the famous aircrack-ng tool set. When using airodump I'm able to see any network and their specs just fine. I don't even have to be in monitor mode to do airodump-ng (the wireless must be off in the network manager though). Is there any way of getting my wireless back when I turn it on again?
I just downloaded Ubuntu Studio on my laptop and I can't get the wireless to work. I think it's because I need a driver; the Atheros AR928x. Whatever the driver is, it works with the pretty unpopular Musix distribution, because wireless worked instantly when I got that. I switched because it was old and slow.
I can't get my wireless into monitor mode. I;m running ubuntu 9.1 karmic It connects fine to wireless networks. But when i do: sudo iwconfig wlan0 mode monitor. I get: Error for wireless request "Set Mode" (8B06) :SET failed on device wlan0 ; Device or resource busy. I can only see wlan0 (wmaster0, eth0), not ath0 or wifi0 mentioned elsewhere, in wireshark. I only see my own ip and packets coming to and from that. my system tells me i have an atheros ar9285 chipset in place.
Does Ubuntu 10.04RC support Atheros AR2427 wireless card out of the box? I ran 10.04RC Netbook Live on my new Asus Eee 1001P Netbook today and it looks very impressive indeed. However, I could not get Ubuntu 10.04 to even see the Etheros AR2427 card (iwconfig). Am I doing something wrong or is there no driver to support the card? If no driver what are my options to get it working under 10.04 as I do not want to use Windows on my netbook..
Just installed Ubuntu 9.1 on a Thinkpad T60P with an Atheros Ar5008 wireless network card. The problem I am having is that I can find my network name and it will even ask me for my password; however, when I type everything in, it seems to be connecting but never does and asks me for my password again. I have verified my password is correct and that my router is using WPA. Anyone else having this problem and is there a way to fix it? I believe the system is using the atk9 drivers.
