Ubuntu Networking :: Atheros AR5001, Won't Work After Turning Off And On?
Jan 12, 2010
I've got a little netbook, and all works fine, except for one small thing. I'm able to connect to a wireless network with my Atheros AR5001 just fine. However, if I right click on the network icon, and disable network or wireless and enable it again, wireless won't work anymore. I can't see and connect to any network at all. Except when using airodump-ng from the famous aircrack-ng tool set. When using airodump I'm able to see any network and their specs just fine. I don't even have to be in monitor mode to do airodump-ng (the wireless must be off in the network manager though). Is there any way of getting my wireless back when I turn it on again?
View 9 Replies
ADVERTISEMENT
Dec 31, 2010
F13 on a EEEPC 1000HD.I have big problems with my wireless card. lspci says:
Code:
01.00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
I can't use Network Manager (it continue to ask me for the WPA password9. So I stopped it and I use command line, following this: [URL]
From the log I can see that it tried to associate to AP and after a lot of tries: it connects BUT the connection is really SLOW and UNSTABLE! (pinging hosts on the same network gives me about 50% packets loss) I am worried about this entry in the log:
Code:
ath5k phy0: unsupported jumbo
I am going to try to install madwifi, but before that I'd like to have your opinion and listen your experience! I see a lot on infos about ath5k, but I'd like to be pointed to the right direction!
View 6 Replies
View Related
Dec 30, 2010
I got a used computer (Toshiba Satellite A215-S5829) for Christmas, and it was running Vista *shudder* so I decided to wipe the hard drive, and install the latest Ubuntu. This is my first real foray into linux, and I've loved the system, but the only problem I've had with is so far is I can't get the wireless to work. I believe the card it has is Atheros AR5001, and I've tried installing the "madwifi" drivers, but I can't get them to register. I've been following the suggestions of dozens of different forum posts and answers I've found scattered around the internet, but I haven't been able to get anything to work correctly.
When I view the "Additional Drivers" in System > Administration, it says "Alternate Atheros "madwifi" driver: This driver is activated but in use," but when I click on the internet icon in the top panel, it only gives me the wired connection. It used to also give me the wireless option, just without ever successfully finding any wireless networks to which it could connect. Like I said, I've done about a half-dozen different things without any success.
View 3 Replies
View Related
Jan 16, 2011
I'm just having a bit of trouble with activating my wireless card (see title for details). rfkill - I installed it but nothing was soft / hard blocked (whatever they mean). I did the rfkill unblock command anyway but it didn't appear to change anything Tried doing it manually through system-config-network but this yielded no luck either. Basically all it does is continually ask for my WEP key, even though I've typed it in correctly a million times. why I don't have WPA2 because I do not have the ability to change it
View 1 Replies
View Related
Aug 10, 2010
I have recently installed Ubuntu 10.04, and today the wireless connection has started to become spotty. The networks menu shows no wireless entries when they were there the day before. Again I have the Atheros AR5001 wireless card, my network is WPA2 and is 802.11g
View 1 Replies
View Related
Mar 2, 2011
A Toshiba 35MX-S114 laptop with Atheros AR5001 works but unless the laptop is in the same room as the router I am not able to connect.
After a relative gave me their old laptop, I installed 10.04 Lucid but I am having problems with the Atheros AR5001 based wifi. I've been able to update the OS using wifi with the laptop in the same room as the router. If I move about 9 metres away from the router into another room, with applet showing 3/4 blue bars and effectively still within line of sight of the router, I lose the connection. Wifi receive is working so well that the Network Manager Applet detects several of my neighbours' routers but not well enough for me to connect to our router.
Originally on the Toshiba laptop under XP there's supposed to be a hotkey Fn+F8 which enables/disables the wifi antenna, in contrast Fn+F9 does disable the touchpad as stated in the manual.
My router is recognised but I cannot connect. Is it a driver issue?
View 1 Replies
View Related
Jul 31, 2011
I've been having problems with the Atheros AR5001 wireless card in my EEE PC. Whenever I'm connected to an encrypted network of any description (WPA2 at home, WPA-PSK at work), the connection will drop out after some time, ask for the key again, then will drop out after a shorter time. This repeats until it's continuously asking for the key. This is no problem with an unencrypted connection. I've installed the madwifi module as per the instructions in this thread, but that doesn't seem to have helped.Ubuntu 10.04.3 LTS, 2.6.32-33-generic i686 kernel.
lspci:
Code:
01:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
ifconfig:
Code:
wlan0 Link encap:Ethernet HWaddr 00:25:d3:12:c3:37
inet addr:192.168.2.4 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::225:d3ff:fe12:c337/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
View 9 Replies
View Related
Jun 17, 2011
I have Ubuntu 10.10 on a Toshiba satellite L300 with an Atheros AR5001 wireless network card. I can get the computer to see the network but it wont persist, it keeps going offline or asking to be re connected.Also Firefox will not find the internet even if the wireless icon shows the wireless network is alive.I can use the laptop for the internet if I plug in the LAN cable but have no luck with the wireless. Security for the modem is using WPA&WPA2 and it will connect according to the icon in the title bar for the wireless network.
I have tried the Atheros site for a driver but had no luck finding one. Not even sure if that is what I need to do.
[Code]...
View 2 Replies
View Related
Aug 12, 2010
I have a Acer Revo R3610 nettop on which I installed oS11.3. It has an Atheros AR5001 wireless network adaptor.I'm getting very bad latency and throughput on with this card. In comparison my Thinkpad with Intel card achieves at least 10 times the throughput from the same location. Also when I boot my wifi will come up authenticate and then a few seconds later disconnect and reconnect. I've tried updating the kernel to 2.6.35 as one of the fixes was to improve the performance of the ath5k driver. I'm using wpa2 authentication.
Here are some details:
Code:
mediacentre:~ # /sbin/lspci -nnk
00:00.0 Host bridge [0600]: nVidia Corporation MCP79 Host Bridge [10de:0a82] (rev b1)
Subsystem: Acer Incorporated [ALI] Device [1025:0222]
[code]....
Is there anything else I paste that will help determine the cause of the bad throughput. Browsing the web or copying files across the network is bordering unusable.
View 9 Replies
View Related
Nov 17, 2010
I have used Ubuntu without trouble for quite some time now on my computer (maybe 2 years; recently upgraded to 10.04) and have just bought a new computer for the office. When I install 10.04 on the new computer it doesn't seem to recognise the lan card, an atheros AR8151 onboard card (on a GA-G41MT-S2 mobo).
p.s. phrases such as 'build-essentials', 'sudo' and '.tar.gz' files don't mean anything to me (except the last is a bit like a zip file I think).
View 1 Replies
View Related
Nov 27, 2010
In my laptop, after upgrade, wifi stop working.My laptop is Fujitsu-Siemens Amilo Pro V2065, wifi cart Philips 12127e (from IBM T41), linux kernel: 2.6.37-020637rc3.This card worked before upgrade, and work on windows Command lshw -c network return:Quote:
*-network:0 UNCLAIMED
description: Ethernet controller
product: AR5212 802.11abg NIC
[code]....
View 4 Replies
View Related
Mar 10, 2011
i'm running Ubuntu 10.10 32-bit on an Acer Aspire 3050 laptop with an Atheros AR5BMB5 WiFi card.
The problem i'm having is that the hardware switch to turn the WiFi on and off isn't working right. When I hit the switch to turn it off, the light doesn't turn off, and Ubuntu just disconnects from the network and searches for more WiFi networks - it doesn't say that the WiFi has been deactivated, and I don't think it is. When I hit the switch again, it finds my network and connects to it.
The lspci -v | less command gives me the following information for the WiFi:
Code:
08:04.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01)
Subsystem: AMBIT Microsystem Corp. Device 0418
Flags: bus master, medium devsel, latency 168, IRQ 21
[Code]....
It lists a different model of card, but it's using what I assume is the correct driver, so I don't know if that has anything to do with it. I've checked the card itself and it is a AR5BMB5.
I would like to fix it so the switch actually turns the WiFi off instead of just making it search for more networks (I assume it's not actually turning off), and perhaps make the light turn off as it should as well.
View 6 Replies
View Related
May 12, 2011
The problem is wireless connections show up in the connections list but when I try to connect it will just keep trying to connect and will never actually complete. During the connecting process it will constantly ask for my WPA2 key. Wired connection does work but that is only a temporary fix to this problem. The phy0 wlan hard block is stuck to yes also, so that could be the problem.other info:Running Ubuntu 11.04 dual boot with windows vista 32 bitWireless card is Atheros ar5001 on Toshiba satellite laptop
View 5 Replies
View Related
Jun 29, 2010
No wireless networks detected with AR5001 chipset
View 1 Replies
View Related
Jul 11, 2011
I installed 11.04 some time ago. I got my printer to work, but I have tried to use wireless and I cant. I can perfectly connect using a wired connection but on the network menu in the taskbar it tells me that wireless is turned off by hardware switch. I am suspecting that I don't have the drivers for my atheros wireless card, but when I click on additional driers it tells me that there are no drivers to download. how to configure my wireless card to work with natty?
View 9 Replies
View Related
May 22, 2010
I`ve read solution in this thread. [URL] It seems Linux driver for AR5001 does`n support ad-hoc mode. But user Selak found solution with a bridge. With this advice by my AR5001 card can finally be detected by other devices. I can connect to it with my girlfriend`s net-book with XP, but I still can`t share internet. May be I miss something. I haven`t shared wifi before.
[Code]...
View 1 Replies
View Related
Jun 25, 2011
Wife's laptop has AR5001 Wireless Adapter laptop model is Toshiba Satellite A215
Problem : Wireless networking randomly loses connectivity and can not regain connectivity, the only apparent solution is a full power down , this is not even certain to work. The card works under Windows, she hates Windows. (I love her for this) I know it's not faulty hardware , because it will work for days on end under Windows without problems.
Things I've tried : madwifi drivers (any and all versions available) : These increase stability of the signal and seem to delay the inevitable however it still happens. When using these drivers the only option is to unload them modprobe -r then reboot then remove them again and re add them. It makes no sense why this works, and if I don't remove them prior to rebooting it will not work.
ATH5K drivers : These are pretty much junk, results are unpredictable at best, sometimes it will work perfectly for a few hours, sometimes it will not work at all. Nothing is repeatable, I can't seem to force whatever condition is causing this. rfkill does not show the wifi being blocked (hard or soft), unblocking it anyway does nothing, only way to make this work and it's iffy is to fully power down wait 5-10 minutes turn it back on and it MAY decide to work.
Firmware update : Updated the Toshiba BIOS to the latest version of the firmware 2.0 no joy here either. Same issue both sets of drivers.
Tried different distros and kernels : I've tried Mint 9, 10 ,11 ; Ubuntu 10.10, 10.04 , 9.10 and 11.04 (which is currently installed) , Fedora and OpenSUSE. All are giving the same problems. I have also tried a slew of different kernels no joy from any of them (I'm not at the computer with the issue now I will post exactly what kernel versions I've used when I have access to the machine).
Another useful bit of information, the hard switch to disable/enable wifi WILL disable it but turning it back on does absolutely nothing. The hotkey does nothing at all. The bios does not have an option to disable or enable the wireless card.
I will also post the typical lsmod , lspci , iwconfig all that good stuff when I get back to the computer in question. I'm probably just going to buy a PC card for it and give up on that one, but this is driving me insane and I would really like to see it resolved even if I do replace the hardware.
View 3 Replies
View Related
May 27, 2010
I have an Acer Aspire One with an SSD for storage. I recently installed Ubuntu on it and chose ext4 for my filesystem. Then I read that journaling on an SSD isn't the best idea, so I will try to disable journaling and I have found these intstructions [URL]..
# Create ext4 fs on /dev/sda10 disk mkfs.ext4 /dev/sda10 # Enable writeback mode. This mode will typically provide the best ext4 performance. tune2fs -o journal_data_writeback /dev/sda10
# Delete has_journal option
tune2fs -O ^has_journal /dev/sda10
# Required fsck
e2fsck -f /dev/sda10
[Code]...
I will use them on my boot partition. Are there any particularly bad parts here, or are there any missing steps? Will my boot partition be fit for being on an SSD after this? Or should I consider switching to ext2, or even reinstall it all and choose ext2 at partitioning time (I'd rather not though, since I've configured quite some stuff already)?
View 2 Replies
View Related
Aug 30, 2010
I am severe wireless problems with Ubuntu 10.04 on my laptop.(Spec below)
I have just performed the first clean install since new. Installed a new Hard Drive as well. The machine and wifi was fine under Ubuntu 9.04.
It is booting much faster now but the wifi keeps dropping off.
Spec:
Machine - Acer Aspire 4310
Wireless card - *-network
description: Wireless interface
product: AR5001 Wireless Network Adapter
vendor: Atheros Communications Inc.
[Code].....
View 2 Replies
View Related
May 10, 2011
I have the dm1 3020 (the version found in most stores) with the ralink rt5390 wifi/BT card that so many people have been posting about, and would like to know how to make sure the bluetooth is disabled. Since I don't have any BT stuff to connect and really want to get all the battery life I can out of this thing I am using Ubuntu 11.04 with KDE, if there is a plasma widget I could use to make sure its disabled? There is no BT icon in the notifications area on the bar.
View 9 Replies
View Related
Apr 7, 2016
I don't know how to make my Wifi Card Qualcomm Atheros QCA9377 to work on my Debian Jessie.
I found driver here: [URL] .....
Tintumon2 said it work for him on Ubuntu 14, but how can I make it to work on Debian?
@update:
When I try to install them on Debian using "./install.sh" I see black screen and then GNU/Linux reboots.
View 4 Replies
View Related
Aug 25, 2010
I have a problem with my internet connection. It is turning on and off all the time. I can maybe surf 3 sites without a problem then the internet goes really slow and after that I wont be able to surf at all. After a while it works fine. I can't even look on ..... videos because all of them stop at half or before. I have connected to my router through my cellphone and my ps3 and those two are working just fine.
I am running ubuntu 10.04 64bits. I don't know what network card my computer has.
View 3 Replies
View Related
Feb 16, 2010
I've searched many forums, and I can't find out how to turn off the wireless connection balloons. I regularly switch between wireless networks, and it's really annoying to have two connect/disconnect notifications each time that I switch between networks.
View 2 Replies
View Related
May 1, 2010
i updated to lucid lynx from karmic (i could not get wireless to work on that either) with the hope that wireless might actually work but it doesn't, the keys to turn wifi on don't even work with lucid there is no way to get the wireless to even give me a light that says its on. I have tried installing the rt3090-dkms package and it installed fine (took ages) however that has done nothing at all. It is kind of pointless having a netbook without wireless so anyone got any ideas this is getting very annoying I have yet to use wifi since i bought the netbook
View 8 Replies
View Related
Sep 8, 2010
I am in a situation at the moment which means I am going to be without an ISp for a week or two, and I can't survive that long without the intenet!!! What's more, I have 8 computers that need to connect, though not necessarily at the same time, but certainly more than one at a time. Anyway, I came up with an idea to buy a Mobile Broadband Dongle, and then share the connection via my PC. Problem is, I don't know how I would go about setting my PC to be a Wireless Access Point/makeshift Wireless Router, and sharing the connection.
View 9 Replies
View Related
Aug 24, 2010
Im trying to maximize my network connectivity. To do this I have begun using the program ethtool. The first thing I did was run
Code:
#ethtool eth0
which informed me Im running 10BaseT mode. So i though, ok, that has to do with the autoneg right?
so I ran:
Code:
# ethtool -s eth0 speed 1000 duplex full autoneg off
[Code]...
LOLz, I got it now, This computer has 2 nics installed! Thats why the link stat was "Link detected: no"
I moded my code to pertain to eth1, the connected port. Eh, anyhow, Im still not sold on this problem being solved, the connection eth1 seems to work fine at 100BaseT/Full but I loose connectivity when trying to use 1000BaseT/Full despite the nic showing it as a supported mode.
View 4 Replies
View Related
Jan 11, 2010
I spent days trying to figure out how to get my atheros AR928x 802.11n wireless card to work in Ubuntu. The card worked perfect in Windows 7 but the connection kept dropping in Ubuntu. It would find my router and connect with 60% signal for about 5 seconds, then fall down to about 25% signal and then cut out altogether. After searching for days to find a solution, I finally figured it out and figured Id post it here to let everyone else in the same boat have a working wireless too!
I found this solution from:[URL].. This solution is for JAUNTY (Ubuntu 9.04), so if you are running Jaunty, you can just follow that post. If you are using Karmic (Ubuntu 9.1), you can follow this tutorial I'm posting. It's pretty simple: First, make sure you got all your files up to date. Type in a terminal:
sudo apt-get update Let that run, and once its done, type into terminal:
sudo apt-get upgrade
Once that finished, restart your computer. Again open up terminal and type:
sudo apt-get install linux-backports-modules-karmic
If you are using Jaunty, instead of karmic type in jaunty, if you use another version of ubuntu, you can find a list of versions and their names here:[URL].. Restart your computer one more time, and you should be good to go! This has been tested and confirmed to work on: -Ubuntu 9.1(karmic) with an Atheros 928x 802.11n wireless card, using the Ubuntu installed network software, in a Gateway NV53 laptop connected to a belkin 802.11n wireless router.-HP base station / 802.11g airport express
This has been tested and does not work/has issues with:
-airport extreme I hope this works for you too, and if it does, please let me know with your hardware and Ubuntu version so I can post here what other setups have been confirmed to let this work.
View 9 Replies
View Related
Apr 20, 2010
Just rebuilt my file/print server using an ECS 945GCD-M Atom motherboard. Running it under 9.10 (2.6.31-20) using the same cable and port on my Netgear switch that my old server connected to at 1GB/s without issue (old server's NIC was Intel-based).
Found the driver is an AR813x, & downloaded & installed the latest driver from here (1.0.1.9). sudo lshw -C network now shows that it's using the new driver, but still sitting at 100MB/s:
Code:
*-network
description: Ethernet interface
product: Attansic Technology Corp.
[Code].....
I can't seem to get it to come up at the full 1GB/s. I also tried ethtool -s eth0 speed 1000 without success. why networking restart ignores eth0?
View 1 Replies
View Related
Feb 25, 2011
I'm trying to get bluetooth working. I have an ASUS USB-BT211 USB 2.0 Mini Bluetooth Dongle. Where do I find the driver and how do I install it? (Currently when I plug the dongle in, it is ignored.)
lshw shows me this:
Code:
Bus 008 Device 003: ID 0cf3:3002 Atheros Communications, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
[Code].....
View 1 Replies
View Related
May 2, 2011
I realise there are a few threads of issues with the AR8152 chipset and Ubuntu 11.04, however, my issue does not appear to be the same as others, nor does there appear to be a consistent solution yet. My ethernet worked fine in Ubuntu 10.10, but after upgrading to 11.04, I experience the errors I am about to explain. I also experience these when booting off a Ubuntu 11.04 Live CD, so it's not just the upgrade the caused the issues. The issue is, if I turn on my system without the ethernet cable plugged in, and then plug the ethernet cable in once I've logged into Ubuntu, the system will not detect it, at all. No amount of network manager of dhclient eth0 will get it to function, however, the device itself still appears in the system. If I turn the system on with the ethernet plugged in, however, it will get an IP address and function correctly. I tried to download the drivers from Atheros and build them, but for whatever reason it complained about me not having autoconf.h or automake.h (can't remember which), despite having build-essentials and linux-headers-generic installed.
View 1 Replies
View Related
