Installation :: Unable To Install Nvidia Driver After Using Dd To Copy Drive?
Sep 25, 2009
I was recently able to obtain a new laptop at work. Rather than reinstalling the OS, reconfiguring all of the software, and then copying over all of my data from my old laptop -- I decided to try to use dd to clone my drive. It worked pretty darn well (thanks Saikee!). However, I have two problems that I have noticed so far:
1) The system does not seem to offer me the option to install the proprietary nvidia driver. I was able to manually install the nvidia-glx-180 package and then edit xorg.conf appropriately and I'm running with the nvidia driver now. So this problem is resolved (though I still find it odd it didn't even offer my the "restricted hardware drivers" option in System -> Administration).
2) Wireless is not working. I checked dmesg and it doesn't seem to have any errors in it. Here is a list of things I have checked/found which I think might be relevant:
- Oddly enough it seems that my wired device always gets renamed from eth0 to eth1, and my wireless device gets renamed from wlan0 to wlan1. I'm not sure why (though I would prefer them to be eth0 and wlan0).
- dmesg output looks good shows some message about the wlan1 link not being ready
Code:
bmayes@bdmlin:~$ dmesg | grep wlan
[ 10.915831] udev: renamed network interface wlan0 to wlan1
[ 185.179556] bridge-wlan0: peer interface wlan0 not found, will wait for it to come up
[ 185.179559] bridge-wlan0: attached
[code]...
View 10 Replies
ADVERTISEMENT
Oct 15, 2010
i tried to go threw this by some tutorials on the wiki but without success. i all the time got this error: Nvidia log: [URL].. even if i ran the make oldconfig && make prepare command..
View 8 Replies
View Related
Feb 16, 2010
I installed openSuSE 11.2 three days ago, the first time, and have been trying to get the nvidia video driver to work ever since. So far, no luck. I have a dual-boot system with Windows 2k (legacy programs) and the graphics card works fine there, so the problem isn't hardware related. The nv driver also works under 11.2, but not well.The graphics card is a GeForce 6200, and the computer is an old Tyan Thunder S2885 with dual Opteron processors. I'm in 64 bit mode for the Linux install.
I've tried installing the video drivers by:Doing a fresh install, loading in the nvidia repository, then doing online update. The two nvidia drivers were loaded (nvidia-gfxG02-kmp-desktop and x11-video-nvidiaG02), but when I tried to reboot I end up with a blank screen and no sync to the monitor (Hitachi SuperScan Elite 751 CRT type). Rebooting in safe mode brings up the nv driver, which works. Doing a fresh install, doing online update,then loading in the nvidia repository, refreshing it, and installing the same two RPMs . . . with the same result. Doing a fresh install and using the "one click" install from this web site. Same result.
Doing a fresh install, doing online update, selecting the pattern "Linux Kernel Development" and installing it, downloading the Nvidia installer NVIDIA-Linux-x86_64-190.53-pkg2.run and installing it. Same result.
Same as above, but then using Sax2 -r -m 0=nvidia, even though Sax is depreciated. Same result. I've tried modprobe nvidia. Nothing. Over the last two days I've probably tried several other iterations as well, and forgot them, but nothing worked, it's always the same result.
Another weirdness, when I have YaST do "Hardware Information" it has no trouble identifying the monitor a getting it's info, but when I click the Display icon on the panel it tells me that it can't identify the monitor.
Here's the basic system info:
Code:
Directory: /home/BillyDoc/Desktop
Tue Feb 16 09:21:23 CST 2010
BillyDoc@linux-k7w3:~/Desktop> lsmod | grep nvidia
nvidia 9647368 0
BillyDoc@linux-k7w3:~/Desktop> su
[code]....
I'm definitely a novice to this sort of thing, and at this point I haven't a clue what's going on. It looks like the nvidia driver get's installed alright, but X simply doesn't know it's there. Oh, and another thing. When I go into YaST to look for the "Graphics Card and Monitor" program . it's missing! I assume this is because Sax is depreciated, but what's the substitute?
View 9 Replies
View Related
Mar 4, 2010
This is my first day with Umbuntu and my first post here at the forums. I bought a Dell Pentium 4 with a fresh install of Umbuntu 9.10 on it. Worked well until I decided to do something a newbie shouldn't do and install a graphics card and drivers. The graphics card worked just fine until the drivers were installed and I tried to reboot the system. Now it no longer boots. Some specifics for you.
Since my time with Ubuntu is limited to hours, the nomenclature will probably be wrong. But I will try to get the point across. The card is a EVGA GeForce FX 5700 Ultra. On first start up with this card the computer functioned fine. I went to a place where you could change the screen options. There were three selections and I don't remember the names (idiot that I am). I selected the middle one. The OS stated that in order to utilize all the capabilities of nvidia graphics cards blah, blah, blah, a driver would need to be downloaded and activated. No name, just a driver. OK, do it (sounds kinda windows like). The download seemed to go OK, but now I needed to reboot to activate the driver.
Now: Ubuntu logo comes up. Screen goes to a text screen that says:
Ubuntu 9.10 dave-ubuntu tty1
dave-ubuntu login:
This screen flashes and does not take input from the keyboard or mouse. Next, I removed the graphics card and used the on-board graphics. Same result with faster flashing. What have I done? Apparently Ubuntu and Linux in general don't have a system recovery option? I read something about the GRUB menu, but the system flasher GRUB loading for half a second and then is on to locking up. I can't seem to get to a GRUB menu. What a way to finish the day.
View 9 Replies
View Related
Dec 19, 2008
I recently reinstalled Debian on my desktop to migrate to 64-bit. Everything was working swimmingly before but I've encountered a bizarre error i have never seen before. After installing the Nvidia driver and rebooting when X comes up it complains it cant find any screens. However, if I kill X and start it again it starts with no issues. I also have an odd message at startup which might be part of the problem as well.I'm running Debian Testing AMD64 with and Nvidia 9800 GTX+. I compiled 2.6.27.8 for the install.
For what its worth the Nvidia module is showing up for lsmod so I don't really know what is wrong. I have tried reinstalling the nvidia driver as well which didn't help. The error message during bootup is:
Code:
Loading kernel modules...Usage: modprobe[-v] [-V] [-C config-file] [-n] [-i] [-q] [-b] [-o <modname>] [ --dump-modversions ] <modname> [parameters...]
modprobe -r [-n] [-i] [-v] <modulename> ...
modprobe -l -t <dirname> [ -a <modulename> ...]
[code]....
View 5 Replies
View Related
May 4, 2010
After upgrading kernel package to 2.6.32-5 NVIDIA installation gave me ERROR:Unable to load the kernel module 'nvidia.ko'. This happens most frequently when this kernel module was built against the wrong or improperly configured kernel sources, with a version of gcc that differs from the one used to build the target kernel, or if a driver such as rivafb/nvidiafb is present and prevents the NVIDIA kernel module from obtaining ownership of the NVIDIA graphics device(s), or NVIDIA GPU installed in this system is not supported by this NVIDIA Linux graphics driver release.
Here is /var/log/nvidia-installer.log:
nvidia-installer log file '/var/log/nvidia-installer.log'
creation time: Tue May 4 11:49:38 2010
installer version: 1.0.7
[code].....
View 12 Replies
View Related
Jul 9, 2011
Infact I've seen the linux(ubuntu 11.04) for the first time today. I don't know anything about linux & i'm not able to install my nVidia 8600gt graphics driver. I've downloaded the .run file from here
[URL]
when I'm opening the .run file it's showing an error
"Could not open the file /home/f1/Downloads/NVIDIA-Linux-x86-275.09.07.run.
gedit has not been able to detect the character encoding. Please check that you are not trying to open a binary file. Select a character encoding from the menu and try again."
After trying for all day long I found this HOWTO
[URL]
View 2 Replies
View Related
May 12, 2010
So after getting around the Fakeraid bug, and the grub bug, and all the other bugs killing my system fixed and then i moved on to install my video driver. There was nothing in Administration>Hardware Drivers, so i downloaded the latest driver for my two 8600m gt cards. Did the whole ctrl+alt+f2 and then stopping xserver and then running the driver install only to run into yet another damn bug(see log below)
I have tried fixing it by doing what other threads have said to do e.g:[URL] still nothing. Below is the Nvidia log.
[Code]....
View 9 Replies
View Related
Aug 6, 2011
I had installed Ubuntu 10.10 and there was a dim spot on the left side of the monitor. I could move the window to the right, but anything on the left was dim, and if I set the window to full screen, the whole screen went dim. I was able to find a fix online, I followed the instructions, and Voila! It was fixed, so I knew it was not a hardware issue. I installed 11.04, and have the same dim screen issue, but I can't find the instructions that fixed it last time. I tried to download and install the latest driver from NVIDIA, and I get this error:
ERROR: You appear to be running an X server; please exit X before installing. For further details, please see the section INSTALLING THE NVIDIA DRIVER in the README available on the Linux driver download page at www.nvidia.com. If anyone has any fix for the dim screen
View 4 Replies
View Related
Jun 15, 2009
I am a new user of Fedora 11. I am a Ubuntu user and could not get my GeForce 9100 on board graphics to work on my new computer with out crashing my computer so I decided I would try fedora. I downloaded the driver from NVidia and I am attempting to install it (Fedora didn't automatically find the driver). I get the following message:
"Error Unable to find the system utility 'ld'; Please make sure you have the 'binutils' installed. If you do have the bin utils installed, then please check that 'ld' is in your PATH."
I am running the driver from $Download as root. I don't know what ld or bin utils is or the check if I have it or if it is in my PATH.
View 9 Replies
View Related
Nov 3, 2010
I have been unable to find a driver for my nvidia geforce2 mx400. It's running in failsafe graphics mode. Does anyone know what I need to do to make it work? I'm a linux beginner, so please avoid jargon.
View 2 Replies
View Related
Dec 15, 2008
The rest of the message is " located in /lib/modules/2.6.24-16-server/build". The version is Ubuntu server 8.04. Why can't it, and how can I help it along?
View 9 Replies
View Related
Sep 19, 2015
I've often installed Debian Netinstall and added the nVidia driver for my monitors. I just purchased a new PC that has this as part of its description:AMD A4-5000 APU with Radeon(TM) HD Graphics..I have monitors connected to both its analog and digital outputs. Larger distros have enabled a good video driver automatically, but I need to know how to do this for my Debian Netinstall partition. The video performance is horribly slow right now.
View 2 Replies
View Related
Dec 10, 2010
I've followed leigh's installation instructions for the nVidia drivers on Fedora 14, and everything seemed to go smoothly, but I don't see any obvious changes after rebooting (should I?).When I go to KDE's KInfocenter (KMenu -> Applications -> System -> Info Center) and check the driver information I see this:
Code:
Vendor Mesa Project
Renderer Software Rasterizer
[code]....
View 2 Replies
View Related
Feb 25, 2011
how do you install an nVidia video driver?
View 1 Replies
View Related
Jul 23, 2011
The nouveau driver coming with the free fedora does not even allow to run Gnome 3, so I'd like to install the Nvidia driver. So far I did not succeed as the nouveau kernel module is loaded at an early stage. How can I remove the nouveau driver?
View 6 Replies
View Related
Nov 1, 2010
I recently downloaded and installed Ubuntu 10.10. I thought it was awesome...still do. OK, the problem is i was prompted to install some proprietary drivers and so i did but thats when the problems started. After reboot i couldn't get the GUI or gdm (not sure what to refer it to) to work. It goes directly to a terminal screen every time so i actually reinstalled Ubuntu and tried installing the drivers all different ways but no luck. i also can get into recovery mode and do low graphics. the driver version im trying to get working is nvidia 260.19.12. my graphics card is a geforce 7 series cant remember the number i have a 32bit processor.
View 9 Replies
View Related
Jul 18, 2010
I've been trying to install the latest driver NVIDIA-Linux-x86_64-256.35.run. I do ctrl+alt+f1 and login, then sudo sh ./NVIDIA-Linux-x86_64-256.35.run and it gives me the license agreement, but after I accept and right after it gets to 100% it says it can't install the kernel or access or whatever. Has anyone done this installation and had the same problem but figured it out??
View 4 Replies
View Related
Nov 9, 2010
I've seen may similar issues to mine, but some are different and others are identical, but have been resolved since in the repositories. I install Maverick from CD, reboot, update via update manager, reboot, install nVidia driver via additional hardware gui, reboot and I can't get into X, I get tty1 instead with a text login prompt.
dmesg tells me:
Code:
nvidia: probe of 0000:01:00.0 failed with error -1
purging nvidia-* and deleting /etc/X11/xorg.conf means that I can get back into X, but without any hardware drivers.
I have both an onboard and PCI-E nVidia graphics adapters but my PCI-E one is primary.
View 2 Replies
View Related
Jun 7, 2011
Can this be done similar to some other O/Ses so Nouveau doesn't pre-screw up the kernel for 3rd party drivers??? Would be great in F16 if we were given a choice re: wanting nouveau or not. I simply can not get F14 or F15 to work with the 270.xx drivers on recent equipment.
View 10 Replies
View Related
Nov 3, 2010
This was my first experience with Ubuntu, I was told to switch the hard drives on my computer and put the Windows drive in a safe place for the install. The first time I did the install on the hard drive (which was the clean second hard drive that came with my computer), I either didn't realize I believe I didn't realize I had to click a button and thought the install had gotten stuck, and therefore cut off the install midway through. The second time around the install went without a hitch, and I was able to boot to desktop once. There, I was notified that I needed/should install NVIDIA drivers, I believe version 173 was listed as the next most recent drives (the other was "current"), I have an NVIDIA GeForce 7350LE graphics card, and after installing the drivers, I went to the restart menu as directed and clicked restart, not shut down but restart, and there were several listed errors on the text/DOS screen, shutdown errors I believe (the errors were 5 digits and were something like 56759 or something like that, I can't be certain if I'm remembering right, though, but there were two errors going over again). I then proceeded to turn off the computer manually, and upon it coming on again, instead of the normal Ubuntu flash screen before login, a more choppy Ubuntu 10.10 screen popped up and it led me to the DOS mode, where I was able to login, but it did me no good because I don't know command logic for Ubuntu. The best I did (its the best I ever do when these things happen) is get menus to pop up that are basically useless. I turned the computer off and on again three times, and tried booting directly from disk, but that failed.
I'm actually using the same computer I just reinserted the Windows drive back in after the frustrating experience. Windows has been giving me problems itself, and I really wanted to switch to Ubuntu but I need to know that this is a fluke and not the norm. I can live with this sort of thing being so uncommon I must have did something that was very strange and out of the ordinary to my computer. But if its commonplace, I want to know that too, because that's just something I can't live with.
View 2 Replies
View Related
Nov 8, 2010
I realize that many have had the issue of getting a black screen when booting up. I'm posting because I've tried a couple fixes that I read after doing a search and haven't had any luck yet. I have the 64-bit 10.04 installed on my netbook and my issue surfaced after installing the current nVidia accelerated graphics driver. Following the install ubuntu now boots to a black screen and nothing more. 'nomodeset' only allows me to boot ubuntu in low-graphics mode (which I'm in now) and this fix hasn't produced a solution either: [URL]..64&postcount=9 My netbook has nVidia ION2 graphics with an integrated as well as a discreet graphics card (Intel GMA3150 and NVIDIA GT21
View 9 Replies
View Related
Apr 29, 2011
After installing debian squeeze I tried installing a nvidia driver. I had to type: /etc/init.d/gdm3 stop The nvidia driver wouldn't install because the 'make' command was missing in a path or something. Now I cannot get the GUI anymore. startx gives me a blank screen rebooting the computer gives me a blank screen. I can only boot in recovery mode. but the nic doesnt work so no internet connection.
View 1 Replies
View Related
Nov 30, 2010
Only about 1.5 weeks into Linux guys so bear with me. I'm trying to uninstall the Nouveau driver and install NVIDIA-Linux-x86-71.86.14-pkg1.run for my old Nvidia TNT2 card. Following these directions I run into a problem in the first step. When I execute the Ctrl+Alt+F1 command and get:
Ubuntu 10.10 splat-desktop tty1 splat-desktop login: if I enter splat which I believe is my username and the correct p/w I get an incorrect login response.
View 3 Replies
View Related
Aug 8, 2010
Can do nothing with the PC. New install of 10.04 and was prompted to install Nvidia driver. Did so. Rebooted, now have nothing except a thin line at top of screen. How can I remove this driver when I see nothing?
View 2 Replies
View Related
Mar 5, 2011
install debian 6 on my pc and have big problem with videoadapter driver i cannot install driver i dowload driver from nvidia do something in google but nothing! palit gtx 460 linux debian 6 x64.
View 3 Replies
View Related
Mar 23, 2011
This is to request the communities assistance with the following: As the title suggests, I am attempting to install 10.04.2 LTS on a PC equipped with an ASUS M2NPV-VM mobo and integral NVidia GeForce 6150 chipset/card and AMD dual processors.
Result: While the CD with the installation software loads, the splash screen comes up distorted and is displayed as several black and white horizontal bars. I have tried this with low end monitors with a VGA input with the same results. It appears to me as if though the video driver on the installation CD is not suitable for the mobo's chipset, but I may be wrong.
View 5 Replies
View Related
May 28, 2010
I just performed a clean install of Kubuntu Lucid earlier this week after deciding it was time to upgrade from Hardy. Pretty much everything worked, until I attempted to install the proprietary NVIDIA driver.
OS details: Kubuntu 10.04 x64 Kernel 2.6.32.22.What happened when I tried to install the proprietary nvidia-current package was simply that it didn't work. I could open the nvidia utility, it would say the driver was not in use. Attempts to force the issue by running nvidia-xconfig would render the X server unable to start, which gave me some quality time in a shell console with APT or restoring the xorg.conf file from backup. Trying to compile and install the driver from nvidia also wasn't working out so well.
I think the issue boiled-down to the install presumably attempting to upgrade the kernel during initial install from CD, but not doing so completely. I had all the appropriate 2.6.32.22 kernel and header packages, but GRUB was apparently still booting to the 2.6.32.21 kernel (which had no headers or anything) and not giving options to boot to the upgraded kernel.
How I fixed this was to remove all packages related to the 2.6.32.22 kernel via APT, then remove all the 2.6.32.21 kernel packages. That second operation triggered the 2.6.32.22 kernel to be reinstalled, and GRUB to be configured correctly to boot to it. At that point, I reinstalled nvidia-current, and it worked. I tried this after determining I was on the 2.6.32.21 kernel, and had no option to boot to the 2.6.32.22 one.
Your mileage may vary. In retrospect, I probably could've fixed it by fixing GRUB to boot to the current kernel. This appears to be a consistent issue, as I reinstalled at one point, just to start over, and went through the same thing again.
I suspect the driver I obtained from the nvidia website and patched (due to issues it has with recent kernels) might work now that I'm booting to the correct kernel with headers, but I think I'll save that for another time since nvidia-current is working great for me at the moment.
View 4 Replies
View Related
Oct 3, 2009
My system specs are..
OS: Fedora 11
CPU: Core2Duo E6750
GPU: Nvidia GeForce 9500gt
MOBO: A-Bit IP35-E
Now, i had an ATI Radeon x1950 and was using the open-source drivers with Fedora 11 and worked fine apart from maximum resolution was 1024x768. So knowing that Nvidia's Linux support was far superior i shelved out on a new GPU the GeForce 9500GT. I tried "yum install kmod-nvidia" - restarted and then the system loads using the nouveo drivers... So i blacklisted the nouveo drivers and changed the xorg.conf file to use the nvidia driver. Restarted, now its using the vesa driver! Blacklisted the vesa driver and after restarting its still picking up the vesa driver! So... i then head to nvidia's site, download the latest driver from there, shut down X-Server, installed them, restarted..... and still using the blumin vesa drivers!
View 4 Replies
View Related
Mar 9, 2011
I installed the Nvidia driver for the on board GeForce 7025 / nForce 630a the "Debian way", according to this link Debian Nvidia Howto. The problem is that the only available screen resolutions are 640x480 & 320x240 and I need something more like 1024x768. The driver is installed correctly, or at least is properly recognized, as in Nvidia Xserver settings, GPU0 appears as GeForce 7025 / nForce 630a.
Here's the xorg.conf file.
Code:
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
[code]....
..only causes gdm not to start.On my Ubuntu partition, I have working the proprietary Nvidia driver (file: NVIDIA-Linux-x86_64-260.19.36.run), and have had no problems from it at all. I was going to install this same driver onto Debian when I read several pages advising to go the "Debian way".
View 4 Replies
View Related
