Since yesterday a constant purple vertical line has appeared on my screen, positioned about 3/4 from the left, which remains even after I reboot.I'm running Ubuntu 10.10 on an Apple iMac (Intel), single boot Ubuntu.
View 8 RepliesI don't seem to have an "xorg.conf" file.
Gateway SB400a computer with Edubuntu Lucid installed. The problem first cropped up when I installed the Edubuntu packages on Ubuntu. I did a fresh install with Edubuntu and the problem persists. I don't want to go back to Ubuntu since this computer is for my Grandkids and I want to the Edubuntu stuff for them.
I don't have the specs handy, but I can get them. what I have to do to get them. (it happens when you get old)
EDIT: From my xorg.0.log: (--) PCI:*(0:0:2:0) 8086:2562:107b:4000 Intel Corporation 82845G/GL[Brookdale-G]/GE Chipset Integrated Graphics Device rev 3, Mem @ 0xf0000000/134217728, 0xffa80000/524288
I can't seem to get Ubuntu to run on my old Dell Dimension 2300. It boots to a purple screen then it goes to a black screen with a load of writing nothing else happens after this screen. [URL] Could someone advise how I can get it to work?
View 1 Replies View RelatedI have been using ubuntu wel a long time now and I know my way around in linux but I recently updated my laptop from ubuntu 10.04 to ubuntu 10.10 all went fine until I had to restart my laptop. I got a purple screen (loading screen) with 4 dots and a oldskool like font which said: Ubuntu 10.10 Right after that the screen goes purple and its like the system halts I hear no login sound etc just a purple screen. So I did a clean install from the 10.10 live cd which booted perfectly fine and the system was also useable like before. But when I installed the system and rebooted it again no problems.
But when I tried to install the proprietary nvidia driver (the recommended one) I got the same problem again the purple screen. After searching a while on the internet I only found posts which had the problem with ATI cards but my laptop is fitted with a Nvidia Geforce 9300 M card. So I tried several things like removing the xorg.conf (read it somewhere) which ofcourse did not work, and booting in graphics fail safe mode which worked. So the point is in 10.04 and 9.10 I CAN use my video card drivers but not in 10.10 is there a solution to this problem? I am talking about the 32 bit version of ubuntu and here's my system hardware profile:
Intel core 2 duo t7350 @ 2,0 ghz / 3mb l2 cache
2 GB DDR3 ram
160 gb hdd
Nvidia 9300m gs
Chipset: I dont know sorry
Model: Samsung R710
I installed Ubuntu 11.04 today as the main OS on my laptop.I had deleted my XP partition, and repartitioned it according to a guide I had found. (http:url)......Basically it was setup like this: 500mb ext2 primary partition, has the grub folder, I believe this is either the '/' partition, or the '/boot' partition 2gb swap space logical partition
10gb ext4 logical partition -- this is either the '/' or the '/boot', it contains the 'bin,boot,cdrom,dev' etc folders 243gb (the rest of my hard drive, with the exception of a partition that contains documents and files from my XP OS, formatted to NTFS) ext4, this is the one that has all my desktop/documents/etc folders.After Ubuntu was done installing, I had some message pop up about installing an ATI proprietary driver for my ATI graphics card (an ATI Radeon HD 4330, I believe, I may have messed that number up). I installed it and rebooted, no problem.
Next, I had another update window pop up with 198 items checked and ready to download and install. I went through all of this, and rebooted, again, no problem.Next thing I did was install some apps that were essential for me to have to use for my work (an ide, chat programs, etc). No problem with any of that.Last thing to install was the OSE Virtualbox, and then I installed WindowsXP Pro and Windows Vista Business, then installed the guest addition addon for VB. This all worked without any issues whatsoever.
Time goes on, and I notice my computer is heating up much more than (seemingly) normal. I begin to wonder if its my graphics card. So I shut down the computer and let it cool down. Reboot, and no problem, still working fine.Then I opened a couple of apps and tried a simple game (can't remember the name) I believe it was a simple 3d topdown, as I wanted to test my graphics card. This is where things seemed to start to go wrong. My laptop began hanging, not even allowing me to access the terminal via ctrl+alt+f2. The screen flashed and I saw the blue/green/grey fuzz that I get when the graphics card is starting to heat up too much. Then everything hangs and I can't do anything at all, including move the mouse. I did a hard reboot (I believe this is what you call pulling the plug/pressing the power button, correct me if I'm wrong). I then rebooted, saw a chkdisk, then it booted seemingly normal, but it hung right after the purple screen after the grub screen.
This is pretty much where I'm at right now. I strongly suspect the fault is with the ATI drivers, but have been completely unsuccessful in my attempts to fix it. I've googled just about everything I could think of, along with searching these forums. I've tried just about everything listed in the forums, but to no avail.I've tried the commands that are supposed to purge the ati drivers, but all I get are errors that say they can't remove the 'virtual drivers'.
Right now I'm booting off a live cd, so I know the computer still works fine, just not my actual installed OS. I'd really like to get the issue resolved without having to reinstall, as it took quite awhile just to get it usable in the first place, but this has already taken so much time, I may just resort to that if we can't solve it any other way. Got too much work to catch up on as it is.As a re-instated note, perhaps if you have any tips, but not particularly about fixing the OS, my laptop (I'm strongly guessing my graphics card) is heating up much more than normal, compared to that when XP was installed. Is this more than likely just a driver issue, as is the rest of it? Also, I did have Compiz installed, though I didn't choose for it to be installed, I believe it came pre-installed. I've heard it could cause some issues, though I have no idea as to the validity or relation to this particular issue.
Edit:
I just remembered while searching for a solution, I found a post somewhere that said something about the information not being sent to the monitor from the graphics card properly, thus no desktop. I'm guessing that'd still fall under the driver issues, but again, I'm unsure. I would think that wouldn't be entirely true anyway, since I can still see my mouse fine, just no desktop, only a black screen.
'm trying to duel boot windows 7 and ubuntu 11.04 on an Acer Aspire 5736, but when I try to boot from the cd (which I burned with InfraRecorder) it first goes to a black screen with a blinking under score in the corner, then to a purple screen with a couple symbols at the bottom, and then the screen goes black and nothing else ever happens
View 4 Replies View Relatedi am fairly new to Ubuntu. i was using it fine for a month, but today, when i booted my computer up, it came up with a black screen instead of the normal purple ubuntu screen. the black screen had white text on it, and asked for my username and password. from there, it was a terminal prompt. i have been google searching for a while, and have tried typing "startx", "sudo apt-get install ubuntu-desktop", "sudo gdm", and i have also tryed uninstalling xorg, and reinstalling, and none of these things wanted to do anything for me.
View 4 Replies View RelatedI'm still getting some vertical lines through my splash screen, they are just a little darker purple than the rest of the screen, but disappear over the ubuntu logo/text/dots. I've tried the following from the faq, which made the screen at least show up, which is wasn't doing before.
Bootup/Plymouth.
Users should experience a much faster boot however some users may experience problems with Plymouth after the nVidia graphics driver has been enabled. Users may experience plymouth using lower graphics resolution. [URL]
Graphical solution : [URL]
Command line :
(Some of the fixes put forward dont work for everyone.)
One that works for nVidia and to try is this.
Code:
gksu gedit /etc/default/grub
and add the line in BOLD.
# The resolution used on graphical terminal
# note that you can use only modes which your graphic card supports via VBE
# you can see them in real GRUB with the command `vbeinfo'
#GRUB_GFXMODE=640x480
GRUB_GFXPAYLOAD_LINUX=1680x1050 Save the file and run
Code:
sudo update-grub
The resolution chosen should be your monitors native resolution.
Other graphics card users may get a black screen with flashing cursor and then a very short duration plymouth. [URL]. One fix for this is to create this file.
Code:
gksu gedit /etc/initramfs-tools/conf.d/splash
and add this option FRAMEBUFFER=y, save the file.
Then
Code:
sudo update-initramfs -u
I am seeing the Vertical screen wrap problem (discussed in [URL]) on a 64-bit Athlon XP desktop with the Ubuntu version that I installed yesterday (10.04 LTS 32-bit).
Vertical screen wrap, with the mouse pointer offset by a few pixels to the north, taskbar partially visible .
The xserver video amd package version is, xserver-xorg-video-amd 2.11.8-4 and the geode package is, xserver-xorg-video-geode 2.11.8-4. Is it possible that the problem lies in the new geode package (and not the intel/amd driver) ?
The screen info says it is 1280*1024*60Hz.I put this into the nouvou monitors hardware control centre. The screen is too stretched in the vertical. Some icons are cut off at the top.The screen is a V7 videoseven.For some reason the menu controls on the screen only work on the non screen movement icons. I cannot access them .how to get the vertical height corrected? If I have I will go back to the NV proprietary drivers but I would prefer not to do so.
View 2 Replies View RelatedI just started and very green, I got a old unit that has Linux instaled. I get home start it and I get a purple screen after gnu grub screen, I'm using a diferent mouse and monitor is all that changed from when I picked it up. I don't know were to start.
View 4 Replies View RelatedUbuntu 9.04 works fine, I have just installed Ubuntu 10.04 Lucid Lynx without problems, it runs fine but after a while the screen starts flashing and the only way out is to reboot with ctrl-alt-del. First of all I get a pale purple screen with blocks of random colour in the middle then it goes on to flashing between two screens. In one the top half of the screen is vertical black and white stripes and the bottom half is black, in the other it is a terminal screen with this distributed across it:
Starting common Unix printing system cupsed
Pulse Audio configured for per-user-sessions
Enabling additional executable binary formats binfmt support
Checking battery state
On the latest occasion the text was "could not write bytes: Broken pipe" repeated all over the screen, followed by "checking battery state".
I've got 10.04 installed on my Blade 1000 workstation. Installed 6.06 first and worked my way up as per other postings. See attached cookbooks I wrote. Framebuffer is Elite3D-lite, and I have done the afbinit install. Using Xorg w/ Gnome and other windowing software to eliminate the possibility it is Gnome. From what I understand, Ubuntu does not require a custom X11 conf file like OpenBSD.
Current screen output shows large vertical stripes, where the stripes overlay on top of the GNOME desktop. Inside the stripes are the prior boot screen output of Ubuntu 10.04. When the screen saver kicks in, the Gnome desktop disappears, but the blue 10.04 stays visible. Mouse cursor moves across the screen, under each stripe as it goes.
My knowledge of framebuffers is limited. Would this then imply that the framebuffer is not fully "refreshing"? The screen does not provide full width even though the correct OpenBoot monitor configuration is set. Haven't found any mention of this issue from other Ubuntu/Linuxes Sparc users. Attached the X11 log. Looking at the log, I suspect this will need a custom X11 config file.
When booting, right after Grub OS selection, Purple screen without ubuntu logo appears for about 3-5 mins without HDD LED flashing. after this 'freeze', same purple screen with logo appears, and it fully loads to ubuntu login screen in about 5 seconds.. is this usual?My spec= 1Ghz CPU, 1GB RAM. Netbook.any idea why and how to fix this?
View 9 Replies View RelatedInsert the boot disk into the drive, boot with dvd drive. get a purple screen with keyboard on the bottom then BAM. Input signal out of range(no video). Hanns G 28' 1080p monitor PNY GTX 260./tear
View 9 Replies View RelatedI've installed almost every version of ubuntu so far and four different versions on this computer, and I've never had a problem with the installation cd. The install cd on this new version however gives me only a purple screen of death with a white line down the middle. What is going on? The ubuntu-10.04-desktop-i386.iso file's md5sum is fine. I've burned it successfully on two different discs and still I can't install it. I've got a Dell 6400 with an nvidia geForce 7300 video card.
View 9 Replies View RelatedMy problem is with the new Ubuntu 10.04 Installer, and the Plymouth Bootloader.
I have installed Ubuntu plenty of times before on my hardware setup, so 10.04 shouldn't be significantly different, however I can't seem to get it to go past the purple screen with the red dots.
If i let it sit there for a while, then press an arrow key, it takes me to the text which is as follows:
Code:
(process:404) : GLib-WARNING **: getpwuid_r(): failed due to unknown user(0)
unable to open '/dev/mapper/nvidia_afgjfcea'
unable to open '/dev/sda'
unable to open '/dev/sdb'
[Code]....
I upgraded from 9.10 to 10.04 2 weeks ago. After a day or so I suddenly couldn't logon anymore. The pc boots, I get the userlist and can enter my username and password, then the userchooser dissappears but the background stays purple and nothing happens anymore. I can still move the mouse and switch to text console but I don't get my desktop. This happens for any user even a new user I created from the command line just to test this. In the end I assumed I messed something up during the upgrade and reinstalled the pc from scratch using Ubuntu 10.04 32-bit.
I was happy for almost 2 weeks but now suddenly I get exactly the same problem. No matter which user account I try I just can't logon (graphically) anymore. Rebooting the system doesn't help. When I run top on a text console I don't see anything hogging the cpu. There is nothing obvious blocking anything. I can't find any clue in /var/log/* or ~/.xsession-errors. I can logon still in text mode as a regular user, my homedir is there, everything looks ok. 1 thing I did notice is that a (few) boots before this started happening autofs suddenly didn't start anymore at boot time (my homedir is mounted from a NAS via NFS). I had to manually start autofs as root to be able to get to my homedir. However this seems to be ok now, automount is running and my homedirs are available. I tried making a new user with a local account just to rule out network issues but even this user can't logon. So the automount issue may be totally unrelated.
I'm getting a screen that has what looks a like a keyboard, equal-sign, then a person in a circle. This happens when I go to install it. I have made new discs and everything and nothing but the screen.
View 2 Replies View RelatedI downloaded the latest LTS last evening , placed it along side my Win 7 , things went well seemingly until I got the install done and restarted the pc. From the initial purple log in area, the second I curse to the place to put my pw the screen blinks off to the purple screen, devoid of the login section and freezes, taking my mouse control away and then it just sticks. I have restarted quite a few times with the same issue. Is there a known issue about Win7 and the latest LTS concerning the log in screen?
if so, what would I need to do to correct, do I need to jump backwards to an earlier version and wait for the issues to be corrected? Is that even possible?
I have 2 monitors my main one working fine, my second one plugged in a usb to VGA adapter displays a purple screen with ubuntu on it and 5 dots but does not go any further than that. In display settings it can not find my second monitor either. Any way to get Ventrilo client on ubuntu. I am using Ubuntu 10.10.
View 3 Replies View Relatedwhen I install them all goes well but when I get into the GUIs I can hardly press anything - major bug with mouse and it is really annoying. Secondly there is a big gap between the GUI and my screen's edge. Hmm, I think - it must be a problem with the GPU driver and that might be the thing also messing with the mouse clicks. I download the drivers provided by the Ubuntu community - all goes well and I restart - stuck at purple screen after the "moving dots" on boot. So I reinstall the whole OS and try with the drivers provided by NVIDIA - same thing. I try the same procedure with Kubuntu and no progress.
View 2 Replies View RelatedI have a macbook pro 5,3 and recently i've upgraded from ubuntu 10.10 to 11.04 , but after the instalation when I reboot ubuntu hangs on purple screen and no login window appears, what can I do to login into my ubuntu?
I've found a strange thing : when the purple screen appears if I wait for about 5 minutes and then restart my computer the next time a window with some options appears and when i choose "use previous version of linux" it goes into natty! I really don't know what's going on
I installed lubuntu 10.10 on my old computer (pentium II, 192 mb ram) but when i try to boot it passes the purple screen and feezes just after showing:
* Starting AppArmor profiles [OK]
* Starting NTP server ntpd [OK]
It was installed on From liveusb with the harddrive plugged into another computer cus the old ones bios doesnt support usb boot.
Yesterday I booted into the Ubuntu 10.10 CD, and hit the Try Ubuntu button. Ubuntu booted fine from the CD, and after trying it for a few minutes, I decided to install it.
I already had (and still have) Windows 7 installed, so, using the Ubuntu Installer, I shrinked the C (system) partition of Windows by roughly 14 GBs. 10 of which used for Ubuntu itself, and the other 4 as Swap Area.
Installation went fine, and I was asked to reboot - and so I did. However, upon restarting, I was 'welcomed' by a stuck, purple splash screen. So I used Recovery Mode, and updated my Ubuntu. That didn't change anything. I rebooted, started Ubuntu without the "splash quiet" commands, and instead used the "nomodeset" command. I logged in my Ubuntu user, and ran the StartX command. It didn't work, and I was given a few errors, including "no screen found", "Fatal server error", and something along the lines of "no NVIDIA module found (...,0)".
So what's wrong with the NVIDIA driver, really?
I switched back to my ubuntu installation few hours ago and I couldn't notice the strange boot screen! I remember that it used to be orange, there was the ubuntu logo and a nice loading bar. All is displayed now is a horrible purple background with just the text "Ubuntu" in the middle and a few dots just below it, showing the loading process.. I don't know how to restore the classic splash screen (I also found the original background in /usr/share/images/xsplash ).
View 2 Replies View RelatedSince upgrading from 9.10 to 10.4 and then on to 10.10, I have only ever seen an uninspiring purple screen (current.jpg, except mine says 'Ubuntu 10.10') as my boot splash image. I have downloaded different themes for Plymouth, selected them, and then updated 'initramfs' (screenshot), all to no avail. I also recently installed Nvidia drivers, but nothing changed. Is there something I'm missing?
View 5 Replies View RelatedI already had Plymouth issues on 10.10, which was solved by this script [URL]
After upgrade, boot only gave me a blank, purple screen, so I used his revert script then tried this : [URL]
But I'm only getting a black screen. Removing vga=795 option only make it stay purple. It might be because of the multiples workarounds I tried back in 10.10, but I don't know how to clean that up. I have an ATI HD Radeon Pro 2400 card with free drivers (but I was using the proprietary ones during upgrade).
I upgraded from 10.10 to 11.04 and now I have a blank purple screen. I have searched and went through some of the steps members have been giving, but haven't been able to fix the problem. I can get into the computer going through the grub menu, but when I restart I go through the same problem.
Here is the computer that I have: [URL]
If you had or have a black screen or purple screen problem in Natty, add support by subscribing to this Launch Pad Bug: Xorg's HAL causes Purple Screen or Black Screen on GDM startup. [URL]
Through helping people with these problems in the Ubuntu Support Forum (Installations and Upgrades) and through this sticky: [URL] this bug (above) seems to be where this problem is originating. It affects this problem with all video hardware types. As I said in this bug report: "Normal users should not have to be highly skilled "techies" to manually bypass a broken part of a system to make a released distribution work during an install or distribution upgrade"