Ubuntu Installation :: Via 8327 Raid 0 - ERROR: Via: Invalid Checksum On /dev/sdb
Aug 12, 2011
I am trying to install Unbuntu 11.04 on a Via raid 0. I have windows already setup and it boots fine, but Ubuntu does not see the raid set. Running dmraid -ay (or any valid switch with dmraid) returns :
sudo dmraid -ay -v
ERROR: via: invalid checksum on /dev/sdb
ERROR: via: invalid checksum on /dev/sda
no raid disks
mainboard is Asus M2V, with 2x Hitachi 250Gb disks in raid 0 configuration set in BIOS. I have a 3rd hard disk on the onboard Marvell 88SE6121 sata controller but this is not seen at all by Ubuntu either. I was thinking of installing it here if Ubuntu does not work the RAID, but no go it would seem. I do remember installing an earlier version of ubuntu on this very same board using RAID 0 (2x 80Gb drives at that time) and the RAID was reconised and worked fine straight from live cd to full install.
View 1 Replies
ADVERTISEMENT
Jul 17, 2011
I burned a new disk with ubuntu 11.04 image and I managed to boot the live cd using my external monitor, I've installed and went into my monitor settings, it displays my external monitor as unknown and doesn't even detect my laptop screen. Changing the driver being used in my xorg.conf to vesa allows me to boot properly and ubuntu uses my laptop screen (yet it still detects it as an unknown monitor). Installing any nvidia driver and using it breaks my system. Heres an image of the laptop when using the nvidia driver (btw I can still hear the ubuntu sound that plays when its reached the logon prompt).
View 2 Replies
View Related
Jul 11, 2011
I'm running 2.6.32-28-generic. I have a raid1 (two 1tb drives with two partitions... one for / and one for /home.) After a power outage, I'm seeing grub complaining about /dev/md0 not existing (ALERT! /dev/md0 does not exist. Dropping to a shell!)
I booted to the latest live CD to have a look around. My dmesg output includes these ominous lines:
Code:
Here is the whole dmesg output: [url]
View 2 Replies
View Related
Nov 11, 2010
I had a RAID controller in a system that would not load Virtuozzo. So I deleted the array created by the 3Ware 9550SX controller before removing it and one drive from the CentOS 4.8 server. Even though I deleted the array when the server boots it shows an error:
ERROR : asr : invalid RAID config table
How can I clear and remove the table without having to reload the OS? Can I? Di I need to run the Seagate Tools and reset the drive?
View 1 Replies
View Related
May 16, 2015
I just installed jessie on a machine that had been running wheezy with no problems. Now I see that a kworker process is hogging nearly 100% of one of the CPUs. I am not sure how to proceed with solving the problem even after doing a number of Google searches.
I'm not sure if this is related, but I am getting the following when I run 'dmesg':
[ 3637.597975] [drm:drm_edid_block_valid] *ERROR* EDID checksum is invalid, remainder is 42
[ 3637.597979] Raw EDID:
[ 3637.597981] 00 ff ff ff ff ff ff 00 4d d9 90 02 01 01 01 01
[Code] .....
My hardware is:
cpu:
Intel(R) Core(TM)2 Duo CPU E6550 @ 2.33GHz, 2333 MHz
Intel(R) Core(TM)2 Duo CPU E6550 @ 2.33GHz, 2000 MHz
keyboard:
/dev/input/event0 AT Translated Set 2 keyboard
mouse:
/dev/input/mice ImExPS/2 Logitech Explorer Mouse
[Code] ....
Here is the "top" display, showing 75.2% of the CPU on kworker/1:2 and 27.6% of the CPU on kworker/1.1:
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
4731 root 20 0 0 0 0 R 72.5 0.0 0:53.73 kworker/1:2
28 root 20 0 0 0 0 S 27.6 0.0 0:58.69 kworker/1:1
1246 dan 20 0 1668476 132720 57548 S 2.7 4.3 0:42.33 gnome-shell
4673 dan 20 0 855208 158368 65568 S 2.7 5.2 0:28.44 iceweasel
815 root 20 0 201804 29020 18728 S 1.0 0.9 0:14.30 Xorg
[Code] ....
View 10 Replies
View Related
Oct 1, 2010
I have got a very frustrating problem. I am not new to Ubuntu but this time I bit my tongue! Actually it is a problem related to my graphics card "Intel 945GM" , it is a real crap card but it is working fine with Windows XP pro (I use windows just for testing)!
Problem : My monitor DELL ST2310 would not work under DVI mode (only VGA mode is working fine)! I tested with Kubuntu, Ubuntu (several distos), Fedora 13.. Upon booting, I get this error message :
Code:
EDID checksum is invalid
remainder 130
the monitor DVI connection is working perfectly under Windows XP. This means the Intel 945GM cannot read the EDID hexadecimal data transmitted by the monitor through the DVI connection. Yet, System recognizes the graphic card's DVI-D port but set it as disconnected.
[Code]...
View 3 Replies
View Related
Aug 16, 2011
Bottom Line: Dvd Drive died in my toshiba laptop and it was replaced (not before tech for some reason reformatted the Win7 partition... which was 100% un-needed, but thats beside the point now. I redid win7 (the tech installed vista) and am TRYING to "redo grub". Facts: The Slackware AND Ubuntu Partitions ARE STILL THERE and when i use SuperGrub Boot CD (which doesn't restore my grub by itself) to boot into slackware, i can see ALL THE CONTENT of both Linuxes still there including grub on ubuntu partition
(Tri-Boot: Ubuntu, Slackware, and WIn7) I had it working for two years or so, SO i know this "setup" works fine. I am A) Trying to do this as simply as possible. B) Trying to avoid the need to download a 800MB ISO (as seen for this issue on this forum) and trying not to have to reformat Ubuntu Partition (though I have the .Debs I have downloaded for it backed up ... all 1.7GB of them) I have /dev/sda1 as win7, /dev/sda2 as Slack and /dev/sda3 as Ubuntu (which contains Grub Legacy).. Every command I do seems to result in an error like "invalid command" or "invalid Execution format " (i think that second one is right) type errors. I compiled (awhile back) a few kernels for Slackware, but feel goofy that I cant figure what i this out (what i thought was going to be a "2 minute" fix)
View 4 Replies
View Related
Jul 3, 2011
i am trying to install ubuntu inside windows xp. But "invalid arguement" error occured.
log file is
[Code]...
View 3 Replies
View Related
Jun 17, 2010
I am a long time Windows user and attempting to install Ubuntu Netbook 10 on my Acer Aspire netbook.I followed the steps:1) Downloading the Ubuntu ISO to my netbook hard drive.2) Installed Ubuntu from the netbook HD to USB using USB universal installer (also using the universal installer to format the USB)3) Set bios to first read USB deviceI receive the following message during the boot "Invalid system disk. Replace the disk, and then press any key.I have retried this process several times.
View 2 Replies
View Related
May 4, 2011
I'm running 11.04 off of a 32gb flash drive. Something about grub on my install is messed up. When trying to boot after a normal shutdown, I get the following errors.
error: invalid environment block
error: invalid arch independent ELF magic
I think something about grubenv under /boot/grub is being corrupted. Loggin in under Ubuntu 10, I can make my way to the files on the 11.04 flash drive and issue the following commands to make it boot normally [URL]... file corruption happening? How can I fix it?
View 2 Replies
View Related
Jul 18, 2011
suddenly after upgrade
2.6.38-10-generic-pae ===> Error 16: Incosistent filesystem structure
2.6.38-10-generic-pae (recovery mode) ===> Error 13: Invalid or unsupported executable format
2.6.38-10-generic ===> Error 13: Invalid or unsupported executable format
[code]....
b08e48b7-1194-49c1-a743-91e7ee90334e is a link to /dev/dm-2 which is my root partition on nvidia raid
PS: At first it did not boot at all dropping out to grub shell, but I managed to boot it with gparted live usb stick and chroot to Ubuntu and re-install grub, but now 2.6.38-8 kernel works and 2.6.38-10 is not
View 1 Replies
View Related
Apr 30, 2011
I have problem witch installing larger packages. Small packages works always. Some bigger works after few tries (like vlc-data). Large packages never works (wesnoth-1.8-music 138MB). I checked many mirrors: main, every from Poland and most from Germany. It same on kubuntu 10.10 and 11.04. My ISP doesn't use proxy of any kind. What could be the reason?
View 5 Replies
View Related
Jan 7, 2010
This has to be the sixth time I am going to have to reinstall Ubuntu (Can't get enough of that Linux greatness) in the past 6 months. I just don't understand what exactly is wrong, I don't install anything extra (but the ubuntu restricted extras) yet updates that ask me to reboot will take me to a GRUB command line screen and trying to boot through the command line interface gives me an, "Invalid Magic Number", error.
There should be an official tool for when problems like this come up, so that users like me can easily move their files off their HDD before reinstalling. I didn't come here to rant but, does anyone know what may be causing this everytime, how it can be avoided maybe even how to deal with the Magic Number error and boot in (I wouldn't mind typing in the commands every time BTW)?
My system
Hp Compaq 6730s
2.0Ghz 575 Celeron
4GB RAM
Intel X4500MHD
Broadcom 802.11b/g
View 2 Replies
View Related
Jan 11, 2010
I have a fairly old computer, (4 years) it is has an Intel Pentium 4 3,4 Ghz processor with 1,5Gb RAM, and had been running XP Home on a 80Gb HDD. About three weeks ago, I purchased a 500Gb HDD, and disconnected my old drive. I partitioned the new drive to 120 Gb and 380Gb. I put XP Pro on the 120Gb partition, and Ubuntu 9.10 on the balance.
On reboot, startup menu (grub?) gave me the option to boot from, among others, Ubuntu 9.10, and XP Pro. Both worked fine! I then reconnected the old drive, and if I wanted to boot up in XP Home, would tap "F8" on start-up, and select the old HDD to boot from. This was working fine and I was happy with the way it worked! This morning, when I re-booted, the Start-up menu now had XP Home added to the list.
If I select either Ubuntu 9.10 or XP Home, they both work fine, but if I select XP Pro, it give me the message "error: invalid signature" and when I press any key, brings me back to the menu.
View 3 Replies
View Related
Jul 25, 2010
I'm trying to install Openshot 1.1.3. from source on Mandriva 2010. I don't understand what else I should do apart from the command "sudo python setup.py install", but clearly this isn't enough, because I get the following error message:
Error: invalid Python installation: unable to open /usr/lib/python2.6/config/Makefile (No such file or directory)
I've put the tarball at /usr/share/openshot-1.1.3. According to Software Management, I have python2.6 installed (and the other dependencies mentioned in the README), but what do I know. (I tried using an RPM file from rpm.pbone.net [URL], but that didn't work out either, I don't know whether this is the easier route or not.)
View 10 Replies
View Related
Aug 5, 2009
I get the following error on 'yum update'. I have tried 'yum clean all' and also:
rm -f /var/lib/rpm/__db*
rpm --rebuilddb
# yum update
Loaded plugins: fastestmirror, protectbase
Determining fastest mirrors
* base: mirror.sov.uk.goscomb.net
* updates: mirror.sov.uk.goscomb.net
[Code]....
View 2 Replies
View Related
Jul 3, 2010
My hard drives kept dropping out of the raid array, so I finally identified the problem as a bad sata cable. I redid the wires and now when I try to assemble I get this:
Code:
mdadm -v --assemble --scan /dev/md0
mdadm: looking for devices for /dev/md0
mdadm: no recogniseable superblock on /dev/sde4
[code].....
View 5 Replies
View Related
Apr 16, 2009
i followed the install method in the g95.org as follows.Installation Notes Unix (Linux/OSX/Solaris/Irix/etc.): Open a console, and go to the directory in which you want to install g95. To download and install g95, run the following commands:
wget -O - http://ftp.g95.org/g95-x86-linux.tgz | tar xvfz -
ln -s $PWD/g95-install/bin/i686-pc-linux-gnu-g95 /usr/bin/g95
everything seemed to work fine. the g95 command in terminal prompted a "no input files" so it seemed to work. i made a quick hello program to test and i get these errors.
/tmp/cc3Ugii1.s: Assembler messages:
/tmp/cc3Ugii1.s:11: Error: suffix or operands invalid for `push'
tested the program with gfortran and it worked fine. i googled around a little and it appears that the error have something to do with a 64 bit 32bit problem. i mean like the compiler is expecting 64 bit, but libraries are 32 bit. or somthing like that.
View 1 Replies
View Related
Nov 4, 2010
I'm getting an md5 checksum error during updating. Using the update manager. I'll post a snapshot.
Screenshot-Changes applied.png (38.46 KiB) Viewed 219 times
View 4 Replies
View Related
Feb 13, 2010
I have a problem. When I start Yast, and it tries to download the update repository, there is a checksum error. The problem is, that this error is always there, it occured about 2 weeks ago and never disappeared. When I change the update repository to a specific one, I chose a german one, there is still that checksum error. If I say yast I want to still use the repository with the error, there comes another checksum error, if i say i dont care about that one either, it says
Code:
"Download failed:./repodata/primary.xml.gz could not be retrieved from http://download.opensuse.org/update/11.2/Progress:-[DownloadCommand.cc:195] caught EOF from server"
View 9 Replies
View Related
Dec 28, 2009
I am attempting to do a new install of OpenSUSE 11.2 x86-64 by burning a network install disk. I am having trouble getting it to work on my hardware however. Whenever I boot up with the disc, I get a "image checksum error." I have tried to redownload the image and also reburn it. The disc will boot in VirtualBox but will not boot on the machine. I do not understand what could be causing this because the CD drive in the machine is working just fine.
View 1 Replies
View Related
Mar 26, 2010
Ive just installed Debian Lenny and then fglrx and kde, but if i try to login to kde, i get an error message because of invalid user. Do I have to enable my user first to login to kde or something?
View 4 Replies
View Related
Jul 22, 2011
I have downloaded the opensuse 11.4 64 bit iso both as a direct download and as a torrent, and the md5sums for both iso images are fine.
I tried burning both, and for both of them they fail the checksum installation media test for the actual dvd.
(dvd title openSUSE-DVD-x86_640024)
I burnt them on a 32 bit Pentium 4 machine running suse 11.3, and am trying to install on an Athlon 64 3000+.
This may well be a stupid question, but do you have to burn a 64 bit iso image on a 64 bit machine, or should I be able to burn it on a P4 ok?
I should add that I had tried installing one the dvd's first, and got a lot of failed packages and ended up aborting the install.
View 3 Replies
View Related
Jan 12, 2011
I had a working dual boot Ubuntu 10 and Windows 7. Anyways long story short, I got it working again but have lost the boot option for windows 7. If i run fdisk -l, I get the following.
root@support-Latitude-E6400:/home/support# fdisk -l
Disk /dev/sda: 250.1 GB, 250059350016 bytes
255 heads, 63 sectors/track, 30401 cylinders
[code]....
I installed gparted and can see that windows 7 is installed in dev/sda6. In another forum, i read that someone had to edit their menu.lst so i did with the following.
title=Windows 7
rootnoverify (hd0,6)
makeactive
chainloader +1
When i try to boot from windows 7, i get the following error. Error 12: invalid device request. How can i get my laptop to boot from windows again?
View 9 Replies
View Related
Jul 18, 2011
I have a raid5 on 10 disk, 750gb and it have worked fine with grub for a long time with ubuntu 10.04 lts. A couple of days ago I added a disk to the raid, growd it and then resized it.. BUT, I started the resize-process on a terminal on another computer, and after some time my girlfriend powered down that computer!
So the resize process cancelled in the middle and i couldn't acess any of the HDDs so I rebooted the server.
Now the problem, the system is not booting up, simple black with a blinking line. Used a rescue CD to boot it up, finised the resize-process and the raid seems to be working fine so I tried to boot normal again. Same problem. Rescue cd, updated grub, got several errors: error: unsupported RAID version: 0.91. I have tried to purge grub, grub-pc, grub commmon, removed /boot/grub and installed grub again. Same problem.
I have tried to erased mbr (# dd if=/dev/null of=/dev/sdX bs=446 count=1) on sda (ide disk, system), sdb (sata, new raid disk). Same problem. Removed and reinstalled ubuntu 11.04 and is now getting error: no such device: (hdd id). Again tried to reinstall grub on both sda and sdb, no luck. update-grub is still generating error about raid id 0.91 and is back on a blinking line on normal boot. When you'r resizeing a raid MDADM changed the ID from 0.90 to 0.91 to prevent something that happend happened. But since I have completed the resize-process MDADM have indeed changed the ID back to 0.90 on all disks.
I have also tried to follow a howto on a similar problem with a patch on [URL] But I cant compile, various error about dpkg. So my problem is, I cant get grub to work. It just gives me a blinking line and unsupported RAID version: 0.91.
View 2 Replies
View Related
Sep 1, 2011
I recently upgraded from 10.04 to 11.04 and I now often get boot messages about a degraded raid.
I'm fairly experienced, but I'm confused which raid it is talking about. I have a raid5 array, but I don't boot of that, and it seems fine when I finally get it to boot. Previously, I didn't have any other raid arrays[1], but now I seem to have two others called md126 and md127, they both seem to be degraded. Where did they come from?
[1] I *do* have two 80GB drives that I was booting from in RAID1, but that was a looong time ago, and I have since only booted from one of them. The partition table indeed shows partitions 1 and 5 are raid autodetect and /proc/mdstat shows they are degraded ([U_]). Could it be that this is causing the problem? If so, why has this only started to happen since the upgrade from 10.04 to 11.04?Anyway, perhaps it is a good idea to add in that second disk to the raid1 array. If so, how to do that? Note that, I've also noticed that when I boot and get to the screen when I select from the different kernel versions, I now get a couple of really old ones too - my thought is that these are from the raid1 disk that I stopped using. If I add it to the array, how can I be sure it will mirror in the correct direction?
It could be that I have fairly recently plugged in that second RAID1 disk, after a long time of not having enough spare sata sockets (I switched my RAID5 array from 8 disks to only 3 disks, so suddenly had a lot more spare sockets).
View 9 Replies
View Related
Oct 15, 2010
Where can I find the md5sum checksum for Ubuntu 10.10? They seem to keep it hidden.
View 2 Replies
View Related
Aug 10, 2010
I have an HTPC that was giving me insane amount of problems after 3 months of good use.
1x 250gig Samsung Drive (OS Drive)
3x 1TB Western Digital Caviar Green (Raid-5)
In 9.10, the raid was working fine. I decided to fresh install Ubuntu 10.04 and I can't seem to start the raid array. In Disk Utility, the array shows up but when I try to start it I get the error "Not enough components to start the array"
I've tried to assemble the array using mdadm and the following:
mdadm --assemble /dev/md0 /dev/sda1 /dev/sdb1 /dev/sdd1
This returns the following error mdadm: failed to create /dev/md0
I have no idea what to do now, and unfortunately I don't have any backups
View 1 Replies
View Related
May 1, 2010
I did the online upgrade from 9.10 to 10.04, using 64 bit. I was forced to as the 2 solutions to my incedibly slow internet lookups both required new package installs, both of which failed, so hoped it was sorted out in 10.04 TLS.
It all went to plan until it tried to reboot. I get this:
mount: mounting /dev/disk/by-uuid/1e4e276c-8741-42e7-b52e-05c195790d28 on /root failed: invalid argument
mount:mounting /dev on /root/dev failed: No such file or directory
[Code].....
I don't have RAID at all a single Samsung 200GB SATA drive as the boot drive. Can someone tell me where to start looking? Also how can a TLS release screw up so badly on a common Gigabyte motherboard?
View 9 Replies
View Related
Oct 3, 2010
i wanted to see the red hat side of things and do some virtualization with CentOS, so i am trying to dual boot ubuntu 10.04 LTS and CentOS 5.5. the machine is a laptop, toshiba A100 series. what I did was to create the following partitioning scheme via Ubuntu LiveCd
Code:
Device Boot Start End Blocks Id System
/dev/sda1 * 1 19457 156288290+ 5 Extended
/dev/sda5 1 2103 16892284+ 83 Linux
/dev/sda6 2104 9988 63336231 83 Linux
/dev/sda7 9995 12623 21117411 83 Linux
/dev/sda8 12624 18800 49616721 83 Linux
/dev/sda9 18801 19457 5277321 82 Linux swap / Solaris
created an extended partition and in there have made sda5 and sda6 as / and home for ubuntu and sda7 and sda8 as / and home for CentOS. and sda9 as swap. I installed ubuntu first and then installed CentOS with no bootloader. Run sudo update-grub through ubuntu and now i have both Ubuntu and CentOS available. But when i select CentOS, i have an error which reads "invalid magic number".
I have grub2 installed, haven't downgraded or done anything to it and the ubuntu install is fresh, one week since i updated to 10.04 from scratch. I have found much contradictory stuff on google, but not something that provides a definite solution and also this post but the second command provided in the solution is one i cannot understand very well and it doesn't seem to work. what I am doing wrong here and how to make this work. I would prefer to do things via Ubuntu since debian stuff is what i am comfortable with and i am installing CentOS to learn not to do work on it.
View 1 Replies
View Related
