Ubuntu Installation :: Network With MSI H61M-P23 Not Working
Apr 19, 2011
I'm building a new HTPC.
The motherboard is an MSI H61M-P23 [URL]
According to the site it has a PCI Express LAN 10/100/1000 Fast Ethernet by Atheros AR8151
I downloaded and installed a fresh copy of Ubuntu 10.10. The network did not work. I've googled around, but havent found a fix. Too new?
I went to Atheros web site [URL] and tried downloading the drivers from there, the download, with extension .tar.gz errors when I tar -xzf it.
View 1 Replies
ADVERTISEMENT
Aug 7, 2011
LM-Sensors can't seem to pull any info on the temp sensors for my new MSI H61M-P21(B3) mobo. Is MSI just not Linux friendly? Or could it possibly be that there really are no temp sensors on this board? I must be missing something simple here
View 9 Replies
View Related
Aug 20, 2010
Config: Squeeze, 2.6.32-5-amd64I just installed squeeze and the network is up and nm-manager deamon if working but the Gnome applet doesn't seem to work as usual. It indicates no network although the network is available as indicated by ifconfig and route below. When I switch WiFi on, the nm works flawlessly. When I click on the applet icon it says "Wired Network: device not supported" (or similar, msg in french is
eth0 Link encap:Ethernet HWaddr 00:1f:e2:12:ea:d8
inet adr:192.168.0.182 Bcast:192.168.0.255 Masque:255.255.255.0
adr inet6: fe80::21f:e2ff:fe12:ead8/64 Scope:Lien
[code]...
View 3 Replies
View Related
Jan 19, 2016
I installed debian 8.1.0 (netinist-i386) in my laptop at work using ethernet (installed mate desktop). At home I do not have such thing, so I should use my phone connection. I can not use wifi due to b43-firmware. I use usb tethering as my only solution. Now I connected to my phone but do jot have internet access in laptop. ping http://www.google.com or 8.8.8.8 or any other address says destination host unreachable,
ifconfig shows usb0 is ok
/etc/resolv.conf:
#generated by networkmanager
nameserver 192.168.42.129
View 7 Replies
View Related
Aug 17, 2011
i installed a linux flavor (Ubuntu 10.04 LTS, Ubuntu 11.04, and then Linux Mint).. They all gave this same problem about the wired network (see the picture). The connection seems to be fine but i can't connect to internet or even to my router. Which is weird since it knows my router IP 192.168.1.79. Wasted the whole night trying to figure it out but i just can't understand why. I have a separate partition on this computer to run Win7 also and confirmed that the network connection is working.
View 9 Replies
View Related
Mar 14, 2010
I met network connection problem in my previous installation, so I tried a second time. But when I try to "enable your network interface", it gave me an error: "An error occurred trying tobring up the eth0 network interface.". I tried again and it just freezed there and won't work anymore.I use Comcast cable service, and a Apple Exteme station as router with gateway "10.0.1.1". This desktop is new HP e9150t with Gigabit Network card. Don't know why.
View 9 Replies
View Related
May 27, 2010
I have just installed openSuse 11.2, but my network connection isn't working. I'm new to linux so i don't know how to approach this problem and how to diagnose what's the problem. Few information about my system: I have Asus X51L laptop with KDE installed. I have cable internet wired to laptop via ethernet network card. In Windows XP my connection is working without problems, but in Suse I have problemsThe main problem is when I enter Suse PC light (on modem) is not working, and it should blink (at least in Windows does). Cable and power light is turned on, and that's good.
View 9 Replies
View Related
Feb 25, 2011
i installed RHEL 6 as virtual host on one of the blades on HP enclosure. i set up network on eth0 and started it but i cannot even ping gateway from within this installation. i logged in as root. i set up everything such as IP, netmask, gateway, nameserver etc.
View 1 Replies
View Related
Jul 25, 2011
I had an Ubuntu Server 32 bit installation and everything was working fine. Now that I installed Ubuntu Server 64bit on a new drive in the same machine, the ethernet card is not working!! This is insane cause when I put the hard disk with the 32bit installation back and booting from it, the ethernet card is working without any problems but in the 64bits installation it is not shown at all using "ifconfig -a"
lspci output:
Quote:
02:00.0 Ethernet controller: Atheros Communications AR8151 v1.0 Gigabit Ethernet (rev c0)
How can I check which module is being loaded in the 32bits installation to try to load it manually in the 64 bits installation?
View 3 Replies
View Related
Jan 29, 2011
I have a Broadcom Corporation NetXtreme BCM5721 network card on my server at work.Everything works fine for a few weeks, then randomly the network connection on the server will stop working. After it stops working, I will try to reconnect with the network manager, it shows a wired connection available, it shows the "connection in progress"animation, then the "connection disabled" icon.
I uninstalled the network manager and used manual configuration, but do you think the network manager was the issue? I can't have the server disconnecting randomly every few weeks with no way to know what the real problem is. Was there an issue with the network manager with 10.04?
View 4 Replies
View Related
Dec 17, 2010
I use an internet connection with a proxy. I have set the proxy in Firefox and systemsettings so now I can browse the web and I can ping Google from Console. But when I start Software Management, it says "Cannot access installation media". Whats wrong?
View 3 Replies
View Related
May 7, 2011
Sometimes my file share network stops working,and will then work again.I'm lost with this problem. The server pc is a Zenwalk pc.The other pc is a win7 pc. This error only occurs on Zenwalk. When i run puppy from the live cd the file shares are always visible,without fail.Under puppy i use pNethood. When the ping command is used there is no problem, and the pc name can be pinged.This is shown below:
[Code]...
View 6 Replies
View Related
Aug 28, 2010
OK so I set up a server yesterday and got ndiswrapper loaded on it with the appropriate driver, I edited the /etc/network/interfaces file to contact my router with it's MAC address, WEP Key, etc... So the problem is I can ping addresses like Google and Ubuntu Forums but I can't use apt-get to install or update packages. When I try sudo apt-get update I get a whole bunch of Code: W: Failed to fetch <address>Temporary Failure resolving <address>My Wireless interface is wlan0 and also I can ping my server from my other computer running Linux and my server can ping that computer too.
View 1 Replies
View Related
Feb 13, 2011
I'm new to SuSe and lateley I was trying to establish a Network, when some weired problems occured. I was able to establish the network and i have connection to the internet. The suse-machine is rechable by ping from all the other computers in the network. If I'm tryiing to ping the other computers from the suse-machine, nothing happens. The router responds without packet loss, but every other ping occurs in:
From 192.168.2.6: icmp_seq=2 Destination Host Unreachable
From 192.168.2.6: icmp_seq=3 Destination Host Unreachable
From 192.168.2.6: icmp_seq=4 Destination Host Unreachable
From 192.168.2.6: icmp_seq=5 Destination Host Unreachable
I've been searching for some ideas to solve this problem but couldn't find any.
View 1 Replies
View Related
Feb 11, 2010
I can not get my network to work.Wireless shows no networks at all and wired the ethernet light does not even turn on. I have dpne heaps of searching but i can not seem to find a solution.
View 6 Replies
View Related
Sep 4, 2010
I am using open suse 11.1 in my acer emachine laptop. Everything is okay except Network cards are not working. It says that firmware is missing or kernel problems. My network cards are Broadcom network cards. How can I fix it?
View 9 Replies
View Related
May 21, 2011
I recently purchased a Dell Vostro v130 which came with Win 7 pre-loaded. I've been using it for a few weeks with no problems, but now I'd like to install ubuntu studio. I made it through the the partitioning part but now I'm getting a networking error: "Network autoconfiguration failed. Your network is probably not using the DHCP protocol. Alternatively, the DHCP server may be slow or some network hardware is not working properly."
I've been using the wireless connection in win 7 without any problem so I don't know why I'm having a problem now.
View 9 Replies
View Related
Mar 11, 2010
I can use the internet on Vista but not Ubuntu. I have gone into my network settings but still no hope.
What should I do?
View 4 Replies
View Related
Jan 13, 2010
I decided to bite the bullet & upgrade from V8 to V9.Now after doing so the WAN connection is not working
Code:
bcm@bcm-laptop:~/wireless$ sudo iwlist wlan0 scan | tee sb.lis
wlan0 Scan completed :
[code]....
View 4 Replies
View Related
Jul 9, 2010
I have a Dell studio 1558 laptop, which I have just installed Ubuntu 10.04 32 bit on it with wubi (It runs windows 7 usually). All seems to be fine, apart from the wireless networking doesn't appear to work. I click on the wireless network icon in the top bar, and it says "wireless: disconnected" and "wierless networks:disconnected".
View 7 Replies
View Related
Oct 6, 2010
OMG i had to do this because i just updated to ubuntu 10.10 from ubuntu 10.04 and now i can access my wireless network at all the funny part is that with ubuntu 10.04 everything was working perfect so please help me with this cause iam new to this and i dont know how to fix this is not my wireless network cause iam writing to you in windows 7 with my wireless network.
View 9 Replies
View Related
Jun 25, 2010
Using 10.04 happily for some time, I shut the machine down today and when I started it back up there was no network.
I've tried to fix the problem myself, but probably made things much worse! I've tried to reinstall the network manager, manually bring up eth0 with a static ip address (it was happily using dynamic earlier today). I even followed some instructions for manually configuring a network interface added an entry to the routing table (which I suspect will turn out to be a huge mistake). No matter what I have done, I haven't even been able to ping my router.
I am not sure what if any of the following is useful: my router is 192.168.1.1 and is set up as DHCP server
ifconfig Code: eth0 Link encap:Ethernet HWaddr e0:cb:4e:32:2e:10
inet addre:192.168.1.5 Bcaset:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[Code]....
View 9 Replies
View Related
Sep 24, 2010
So i just managed to get a flash drive version of xubuntu, trying my hardest to figure out how to get the network up. i have wireless but xubuntu doesnt seem to scan for them and manual input of network names and key doesnt work either.
View 10 Replies
View Related
Jan 22, 2010
I'm clearly missing something small. My Ubuntu machine can see the XP machines in the WORKGROUP, pull files over and even print to the printer attached to one of them. Internet sharing also works. However, the XP machines cannot find the Ubuntu system.
View 1 Replies
View Related
Mar 14, 2010
I have just done a new install and have no network (LAN) connection.My network card blinks as if there is activity but the corresponding diode on my router is not active.I have checked the ethernet cable by switching with a valid connection to a WinXP system; like this I know that all the router ports are good.The network configuration module does not indicate a wired connection.
I have also tried sudo ifdown eth0 and sudo ifup eth0 but receive error message: interface eth0 not configured Can anyone help as it is my first experience with linux systems.
View 2 Replies
View Related
Apr 30, 2010
I've followed several guides and am trying to get NFS working on my local network. For starters, I think I should be able to NFS mount a drive on the server (192.168.1.65) TO the server. From there I'll work with another client (currently 192.168.1.80)
Code:
$cat /etc/exports
/media 192.168.1.0/24(rw,no_subtree_check)
$cat /etc/hosts.deny
portmap mountd nfsd statd lockd rquotad : ALL
[Code]...
The guides I've read seem simple, so I must be missing something easy. Can't figure it out, so I'm looking for help after googling for 2 hours.
View 9 Replies
View Related
May 2, 2010
I was using before in dual-boot both Win7 and Ubuntu9.10. I've upgraded yesterday Ubuntu to v. 10.04 and since then a strange thing happened. My (wired) network works fine under Ubuntu. Internet connection is all right, download speeds seem normal,etc. I booted back into Win, and it informed me that my cable is not plugged in. Very weird, because in Ubuntu I had no problems. I disabled the device, rebooted, Windows re-installed the driver for me, but still, the same problem. As I was planning to do it, I even re-installed Win, but STILL, the same problem.
So now, I'm in the strange situation that I have internet connection under Ubuntu and a "please plug in your cable" message under Windows.
View 5 Replies
View Related
May 10, 2010
so i just downloaded Ubuntu Server 10.04 and i'm very happy with it on my virtual machine... but when i try to install it on my actual server it fails.
When i went to install it, it told me that there was no network hardware detected or something like that. So i just thought i could install a driver for it later.
So other than that all went well. and im very happy but now i dont know how to install my network driver. The card is a LYNKSYS LNE100TX. i downloaded the driver software and burnt it to disk because i was out of floppys. (I like floppys better) and when i went to install the software it allmost worked but it said:
Code:
make: gcc command not found
I'm assuming that means i need to install gcc but didn't really know how to go about it having no internet.
View 6 Replies
View Related
Jun 25, 2010
Using 10.04, everything working fine every day since the install a month or so ago. I shut down the machine normally, when I returned a few hours later it started up without a hitch, but without network. I found a thread suggesting the following (in the case of a failed suspend, which did happent to me a few weeks ago)
Code:
service network-manager stop
rm /var/lib/NetworkManager/NetworkManager.state
service network-manager start
but it didn't help.
My ifconfig looks like this
[Code]...
View 4 Replies
View Related
Aug 2, 2010
I have posted this in networking, but perhaps it should have been here. Can anyone give me a clue on how to get my networking to work again? I don't care about sound.Last night I was trying to get my printer working, and when I rebooted, I lost networking and sound.I am currently booting on a live CD, and sound and networking are fine-- so it can't be a hardware issue (obviously). I must have inadvertently broken something, but I can't figure it out.
I have tried restarting networking, but it doesn't respond-- it says stop/waiting or something like that.I can't access the sound preferences-- it says waiting for sound to respond (or something like that).When I reboot, sometimes I see a terminal window with the same line scrolling very, very quickly-- something about waiting for USB.Additionally, the system is very slow to respond-- clicking a menu item can take a long time for it to appear, etc.
View 5 Replies
View Related
