Ubuntu Installation :: Grub Update - Can No Longer Boot Vista
Feb 27, 2010
I recently installed Ubuntu (Karmic Koala) on a Dell Inspiron 1525 which already had Vista installed on it. The installation went just fine and I could boot into either Ubuntu or Vista using the Grub bootloader options. After updating grub through the update manager however, I can no longer boot into Vista and get an error message that says:
"Windows cannot start. A recent upgrade or hardware change may have caused this".
And below that:
File: \boot\bcd
Status: 0xc000000e
info: An error occurred while attempting to read the boot configuration data"
When I run sudo fdisk -l, I get the following:
Disk /dev/sda: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000080
Device Boot Start End Blocks Id System
/dev/sda1 1 6 48163+ de Dell Utility
/dev/sda2 * 7 13619 109345113+ 7 HPFS/NTFS
Partition 2 does not end on cylinder boundary.
/dev/sda3 13619 15936 18605117+ 7 HPFS/NTFS
/dev/sda4 15937 19457 28282432+ f W95 Ext'd (LBA)
/dev/sda5 19066 19457 3148708+ dd Unknown
/dev/sda6 15937 18930 24049242 83 Linux
/dev/sda7 18931 19065 1084356 82 Linux swap / Solaris
Partition table entries are not in disk order. I have the Vista recovery disk but was wondering whether using it to repair the Vista bootloader might mess up Grub.
View 4 Replies
ADVERTISEMENT
Mar 21, 2010
upgraded from 9.10 to 10.04 beta today.Ubuntu boots but not Vista boot info script info for my system as follows...Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================
=> Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in
partition #7 for /boot/grub.
=> No boot loader is installed in the MBR of /dev/sdb
[code]...
View 2 Replies
View Related
Apr 27, 2009
I will be booting Vista, XP, and then installing Linux with grub. So the Vista boot loader will be setup to boot both Windows, so then when I do install a Linux on the same hard drive, (all on separate partitions) what is the best method to boot up all 3 systems?Should I just allow grub to install on the master boot record, and then chainload XP and Vista. Or I could install grub on the boot sector of what will be my Kubuntu root partition, and then try to add this Linux to the Vista boot loader ?
View 7 Replies
View Related
Jul 2, 2011
I'm new to linux systems and just installed Fedora 14 onto my Windows Vista laptop. I chose the shrink existing system option and then proceeded to install Fedora. The only problem is that when I choose Other in the Grub boot menu my Windows Vista goes straight to the recovery screen and does not boot. I don't want to do a point recovery. Is Vista not running because I shrunk it or because of some configuration that I did not add in the Grub files. How to solve this problem and get Vista running properly from the dual boot menu?
View 2 Replies
View Related
Dec 31, 2010
I have just installed Linux on a partition of my hard drive. Computer boots up and gives me the grub boot screen where I can choose from: ubuntu, some memory tests and windows recovery environment (loader). But no Windows Vista. When I boot the windows recovery option the windows boot loading screen comes up but then the screen turns blank but the hard drive is still working and the wifi light also comes on my keyboard. Ubuntu is working completely fine I just need to find a way of getting Grub to display Vista instead of the Recovery environment.
Here is my Boot Info Script: .....
View 9 Replies
View Related
Mar 7, 2009
I am new to Fedora, having used Ubuntu for 2 years. However, I am a little dissappointed in the latest Ubuntu releases and want to try something new. So I installed Fedora 10 on my second hard drive, deleting Ubuntu. On my first hard drive, I have Vista installed. During installation I followed a guide for dual-booting and it said not to install Grub to the MBR of the Windows partition, so I followed that advice...
This caused a Grub error 15 on the next boot. I booted the Fedora installation from the second hard drive. My hypothesis is that the Grub bootloader of Ubuntu was still installed somewhere and it could not find the Ubuntu linux kernel. Therefore, it gave error 15. So I installed Vista again and am hesitant to try Fedora again... How can I install Fedora alongside Vista properly (as dual boot)?
Or should I stay away, because it is apparently too difficult for me? Is it worthwhile to make a separate /home partition as I read that it is preferred to do a clean install every release? Could I just do that with Gparted and then assign the partition as /home in the Anaconda installer? The downside is that I then need to create a swap and / partition too, right?
View 6 Replies
View Related
Nov 6, 2009
Shrinking the Vista partition and format the rest of the HD as ext4 and install Fedora into that partition and put the GRUB in MBR, is this the right way to dual-boot fedora with Vista?
View 4 Replies
View Related
Apr 27, 2010
I've got a machine that I'd got 9.10 on, that I've now upgraded to Lucid Lynx - and I'm having the same problem with dual boot (or lack thereof) that I was having previously.
Rough scenario is:
(Original Vista machine had)
C: Windows Vista OS + Windows software, etc.: 500GB - single NTFS partition - SATA drive
D: General dumping ground for data. 500GB SATA drive. Was single NTFS partition, now shrunk to install Ubuntu.
So is now:
- NTFS partition (containing general rubbish)
- Ubuntu / partition
- Ubuntu swap partition
... and then 3 x 1TB SATA drives making up an (Intel ICH9R) FakeRaid RAID5 array - that Windows can happily 'see' and use, but I don't care about Ubuntu having access to it or even seeing it.
Lucid Lynx is installed to /dev/sde6 (IIRC) - but when I boot the machine just boots straight into Vista.
I've done what I can to try and get GRUB correctly installed - to the point that right now I probably have it splattered just about anywhere and everywhere.
So - now - the machine boots and simply presents me with "GRUB Hard Disk Error" and stops...
I can fix this by running the Vista repair, with a fixmbr etc. and putting the MBR back to 'normal' on the first boot disk (/dev/sdd in this case). The machine then just boots straight into Vista.
...or I can boot into Ubuntu (or Vista) by booting off a Super Grub Disk (CD) and selecting "Boot Linux" (or whatever it is) - and it correctly boots Lucid Lynx from /dev/sde6
Ideally I want a proper GRUB dual boot menu - but I just seem to be getting into more and more of a mess!
Bootlog below will show what sort of mess I'm in:
Code:
Boot Info Summary:
View 2 Replies
View Related
Dec 24, 2010
ok so last night i had my computer set up and working with both vista and ubuntu dual boot so when i started my computer i had a choice between ubuntu or vista went back and forth a few times to make sure everythign worked fine and it did. so this morning i update my vista basic to 7 home premium well now when i start my computer i no longer have a choice and it boots directly into 7. can someone help me fix this i really liked being able to have both on on hdd
i know that ubuntu is still there becouse my hdd reads 220 free of 250 the hdd is 320 i set the other half for ubuntu
View 7 Replies
View Related
Jan 25, 2009
I did a fresh install of Fedora Core 10 32bit on my Caompaq Presario AMD 64 laptop which originally only had Vista ultimate 64bit. When I go in to grub and choose windows I get a screen that says:
Windows failed to start...
File: windowssystem32winload.exe
Status: 0xc0000225
Info: The selected entry could not be loaded because the application is missing or corrupt.
View 9 Replies
View Related
May 11, 2011
error: unknown filesystem grub rescue>
Background: My mother's HP laptop had Ubuntu and Vista on it, Ubuntu my brother's doing. He decided he wanted to take off Ubuntu yesterday (he had forgotten the password), and deleted the partition that it was contained within. The computer now boots to this error.
Inventory: We no longer have the install disk for Windows Vista, he cannot tell me what version he used of Ubuntu, what partition it was on, any of the specs for the machine, or generally any information about the system. All I am aware of is that error on the boot-up screen. I have nothing else to work with.
I would like to remove Grub, and Ubuntu, and leave Windows intact (the request of the owner of the computer), but I have no idea what commands I could use to get rid of either when I can't access Windows, or how to properly remove them if I did access Windows.
View 10 Replies
View Related
Apr 29, 2010
I upgraded today to 10.04, everything went fine and was working fine. I went to boot back into Vista via grub2. I immediatly get the PXE-E61 Media Test Failure, check cable PXE-M0F Exiting PXE ROM
I first checked my boot order, and lan is very last. Also, through Ubuntu I can view everything on the hard drive so it is not that. I think it may have to do with during the update process, it asked about grub2 update preferences and asked about different drives and such (I am not exactly sure what it was called). I didn't select all of the choices, and I believe this may be the cause, as this was the only thing I had control of that I could have screwed up.
View 9 Replies
View Related
Mar 4, 2011
I have 2 hard disks. sda,sdb
In sda, I have 4 partitions, and I have windows 7 in one of the extended partitions [not in the primary partition].
In sdb, I have 3 partitions. 2 for storage, and 1 10GB drive for Ubuntu. Again, Ubuntu is not of a primary partition.
I had ubuntu 10.04 running on that for a long time. However, I wanted to reinstall ubuntu and use 10.10.This is what I did EXACTLY:Booted from Ubuntu install CD
Chose advanced istall
Selected sdb3 for Ubuntu
I installed GRUB2 on the SAME partition as Ubuntu aka sdb3 Installed then rebooted
I can boot into Ubuntu fine, but whenever I select Windows 7 bootloader from the GRUB menu, the screen goes black, and my PC reboots.
Boot Info:
Code:
Boot Info Script 0.55 dated February 15th, 2010 [code]....
ls: reading directory sda6/: Input/output error
I have tried the testdisk/update-grub method, but it didn't work.
View 9 Replies
View Related
Nov 22, 2010
I've been using Fedora 10 for a while, but after i upgraded to vista a long time ago, it changed the MBR so my dual boot no longer worked. Coincidentally I no longer needed linux at that time so I never bothered to fix it. Now I need it again and I was wondering how I could fix the MBR to get back my dual boot. When I insert the Fedora 14 LiveCD it just takes me to the OS...
View 3 Replies
View Related
Dec 20, 2010
I've been using Linux for over a decade, so no need to worry about the obvious. I'm positive that I have my partitions/install correct. What has me baffled is that Fedora 14, which uses GRUB 0.97 (GRUB legacy) - boots Windows flawlessly every single time on the same hardware, but Ubuntu's (or the upstream Debian's) GRUB legacy do not - even though they are based on the same upstream code from the GNU Savannah servers.
No matter what I've tried I cannot get the Debian or Ubuntu version of GRUB/GRUB-legacy to boot any recent Windows 64 beyond XP (Vista or 7). All that it does is resets the computer when Windows attempts to boot, without an error. GRUB is notoriously difficult to compile, so before I try to compile code from RedHat's archives - any thoughts,experiences, similar issues - whatever?
View 9 Replies
View Related
Apr 7, 2010
after doing an upgrade to 10.4 and updating grub I get this message. how do I address this
[Code]...
View 2 Replies
View Related
Jul 5, 2010
I have a Dell Inspiron laptop which was set up to dual boot windows Vista and Ubuntu 10.04. I created a live USB image for Ubuntu 10.04 using Unet bootin and rebooted from from this to install Ubuntu on an SD card. When I remove the SD card and reboot the laptop I no longer get the GRUB loader menu, instead I get the GRUB error message. I can not now boot into Windows Vista or Ubuntu! Obviously I have caused a GRUB error. I have rebooted using the USB live image and run fdisk l and blkid, the outputs are listed below. how I can restore the GRUB loader menu back please so that I can access Ubuntu or Vista?
[code]...
View 4 Replies
View Related
May 7, 2010
I had 9.10 installed and I did an upgrade to 10.04. However I cannot see anymore my Windows Vista partition with grub.. I have a Toshiba laptop Satellite p305.This is my boot script output:
Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================
=> Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in [code].......
View 3 Replies
View Related
Mar 18, 2011
I have a single hard-drive on a spare computer and I decided to try out Ubuntu on recommendation from a friend. I really like it now but at first I just dual-booted it, and now I want Vista gone. I know it's unnecessary to have just one OS but my hard-drive isn't particularly big and I'd prefer to have Ubuntu by itself. Can anyone tell me how to eliminate vista and leave Ubuntu as my sole operating system (I've all my files from computer on another computer so I don't have to worry about losing anything).
View 2 Replies
View Related
Oct 9, 2010
i have just installed fedora over a existing copy of ubuntu. The problem is i cant boot in to vista any more. i have looked over many forums trying to fix it but still wont work.the attachments are of screen shots i have with the details of the hard drive partitions.i am able to mount the hard drives and have all the data still and still have the boot folder for vista but just cant figure out how to boot in to vista.i also get the error " error 1: filename must be an absolute pathname press any key to continue" i get this error when i try to change the boot partitons
View 4 Replies
View Related
Apr 6, 2011
I installed Ubuntu 10.10 on my PC running Vista Home Basic. I installed to run as a dual boot but now I can only boot into Ubuntu. I have tried to run the recovery disk for Vista and it errors out also..
View 6 Replies
View Related
Aug 20, 2010
I am dual booting Windows Vista and Ubuntu 10.04 with WUBI. (Windows works fine). When I updated Ubuntu from the update manager, it just gives me this error code from a JPG attachment I just added with this post. It keeps on saying that every time ubuntu boots up.Is there a Fix? I cant boot up to ubuntu at all...
View 1 Replies
View Related
Jul 21, 2010
I have been phenomenally unlucky with Ubuntu as seen my my post history and decided to dual boot.
I set it all up with a clean install, when I tried to load Windows from Grub the computer restarted. After much headache I managed to set it up correctly (when it wouldn't load from Grub I booted from the Windows CD and clicked on "Repair computer" and it finally worked).
Now I am having the same problem as before--I think my installed all the updates from Update Manager and it included a grub one. Now I can't load Windows from the grub menu: It goes to the Starting Windows screen and then reboots my computer. If I do it again it gives me an error message and an option to perform "Startup repair". When I try to do Startup Repair, the computer reboots after a few loading screens.
So I tried what worked before and put in my Windows 7 CD, and clicked on Repair Computer. BUT NOW it gives me an error message somewhere along the lines of system restore is not compatible with my installation of Windows, and to insert a compatible recovery CD. This is the ONLY Windows CD I have (legitimate copy).
Over the course of this migration experiment I have installed and reinstalled both operating systems 7-10 times total. I'd rather not do it again. My poor laptop is probably wondering what the heck.
I can't stick with Ubuntu alone because my wireless doesn't work with it, my grad school files are not completely compatible with open source software, and I can't play the games I'd like to. So I must have the option to at least dual boot into Windows.
When selecting Windows it restarts the computer entirely to the Compaq screen, not just to the Grub menu, if that matters.
View 9 Replies
View Related
Jan 9, 2010
I used the update manager to update the kernel and whatever the other recommended updates were yesterday. I shut the computer down overnight and now when i try to boot into Ubuntu 9.10 i get a basic grub shell and when i try commands like "boot" it tells me there is no kernel loaded. I installed Ubuntu with Wubi so it is a dual boot system.
I've tried to access the Linux volume with a live OpenSuse 11 CD but there is no device to mount. It sees the entire hard-drive as if it hasn't been partitioned. I don't necessarily need to fix the installation. I just need to get my files back.
View 9 Replies
View Related
Sep 29, 2010
I recently updated, and now when I boot it only goes as far as grub command line. There is no grub menu. The computer is a Dell Inspiron 8600 laptop with only Ubuntu installed -- no dual boot, no weird partition schemes. Originally installed Ubuntu 09.04 on this computer, upgraded a couple times and it currently has (had) 10.04.1 LTS running. The update should have upgraded from kernel 2.6.32-23 to 2.6.32-24. I can boot with a live CD and mount the hard drive. The drive seems fine, so it appears to be simply a grub config issue. I have to boot with live cd to get online to check for potential solutions. So I'm taking some notes on how to use grub.
View 4 Replies
View Related
Oct 23, 2010
With a bit of help from this forum I managed to install 10.04. The solution was to add i915.modeset=1 to the options when booting up from CD.Now I need to do the same in order to boot up from HD. I've opened /etc/default/grub and changed the relevant line to include the above option. But I need to run "update-grub" and it comes back with an error to the effect that it 'can't find a device for / (is /dev mounted?)Also, the boot menu only has ubuntu - no sign of windows in my intended dual-boot. What can I do?
View 9 Replies
View Related
Jun 6, 2011
I just updated my server from Ubuntu 8.04 to 10.04 and now it cannot go past grub, at boot time, it would "give up waiting for root device", asking me to check whether I gave the right "root=..." or if I should increase the "rootdelay=..." in the command line argument and end up with the initramfs.
The machine is a Dell Poweredge 2900 with a HW RAID controller (I hope that should not matter, but just in case...). I tried to follow the instructions there to make sure grub is setup correctly, but without any luck.
Below is the output from the bootinfoscript (while running on the LiveCD). Anybody has any idea what can be the problem or what I could do to debug this ? I am running out of ideas.
[Code]...
View 1 Replies
View Related
Aug 24, 2010
I've previously had a dual boot Vista/Ubuntu machine that was working fine. Fast forward, I'm not able to boot into Vista at all and decide to reformat, return to factory settings after which I'll simply reinstall Ubuntu to get my functioning dual-boot back. I reformat the drive, everything seems to work fine and when I reboot I'm met by the GRUB screen rather then the Vista bootloader screen I expected. I select the Vista option and rather than starting to boot, seeing the Windows splash and then breaking (as it's been doing for a few weeks leading up to my decision to reformat), I'm promptly given a message that it can't find the disk 5252-ACFA (that Vista was previously on). After further inspection, my Ubuntu partition is still in tact and untouched, so I think the 'reformat' simply reformatted the Vista partition not the entire HD as I'd wanted. How do I modify GRUB to point to the new correct Vista boot?
View 4 Replies
View Related
Apr 30, 2010
I had been dual-booting Ubuntu and Windows 7. Today I upgraded to Ubuntu 10.04 and now Grub still has a Windows 7 boot option, but when selected it goes to a blank screen and does not boot Windows 7 as it would before.
View 4 Replies
View Related
Apr 28, 2011
When I first boot up. I get the GRUB command line. What happened to the boot menu? And I can boot up into my Windows partition just fine. But when I try the other partitions i get "Unknown file system" or when I try to boot into the other ntfs drive, I get "BOOTMBR missing", but yet it does not mean Windows, because i can boot that just fine. I can't find my Ubuntu partition. How can I get the GRUB boot menu back?
View 1 Replies
View Related
