I had been dual-booting Ubuntu and Windows 7. Today I upgraded to Ubuntu 10.04 and now Grub still has a Windows 7 boot option, but when selected it goes to a blank screen and does not boot Windows 7 as it would before.
View 4 RepliesI recently installed Ubuntu (Karmic Koala) on a Dell Inspiron 1525 which already had Vista installed on it. The installation went just fine and I could boot into either Ubuntu or Vista using the Grub bootloader options. After updating grub through the update manager however, I can no longer boot into Vista and get an error message that says:
"Windows cannot start. A recent upgrade or hardware change may have caused this".
And below that:
File: \boot\bcd
Status: 0xc000000e
info: An error occurred while attempting to read the boot configuration data"
When I run sudo fdisk -l, I get the following:
Disk /dev/sda: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000080
Device Boot Start End Blocks Id System
/dev/sda1 1 6 48163+ de Dell Utility
/dev/sda2 * 7 13619 109345113+ 7 HPFS/NTFS
Partition 2 does not end on cylinder boundary.
/dev/sda3 13619 15936 18605117+ 7 HPFS/NTFS
/dev/sda4 15937 19457 28282432+ f W95 Ext'd (LBA)
/dev/sda5 19066 19457 3148708+ dd Unknown
/dev/sda6 15937 18930 24049242 83 Linux
/dev/sda7 18931 19065 1084356 82 Linux swap / Solaris
Partition table entries are not in disk order. I have the Vista recovery disk but was wondering whether using it to repair the Vista bootloader might mess up Grub.
I've run into a strange problem recently. My primary OS right now is Windows 7, and OpenSUSE is secondary. I had GRUB as the bootloader, and everything seemed fine, but I ran into one problem in Windows 7: one program refused to work correctly with ATI forced anti-aliasing on, but it is needed by others (or else edges look jagged).So I decided to install ATI Tray Tools. But it seems that Windows 7 is being evil and won't let install drivers that their creators didn't pay Microsoft for (thank goodness that's not the case in Linux). That means I had to use a driver overrider program, and that means that it had to change the Windows 7 BCD options. And that's where bootloaders kick in. It seems that Windows 7 is too lazy to check for its BCD on other than active partitions, so it doesn't allow the overrider to function.
So what I did was change GRUB to boot Windows 7 with makeactive flag. The problem now is - it won't deactivate! I no longer get GRUB's boot screen, it just boots to BCD directly. So my question is - is there a way to deactivate (or, rather, reactivate the /boot partition) after Windows 7 shuts down or restarts automatically? Obviously I don't want to use GPartEd each time I want to boot to Linux.
error: unknown filesystem grub rescue>
Background: My mother's HP laptop had Ubuntu and Vista on it, Ubuntu my brother's doing. He decided he wanted to take off Ubuntu yesterday (he had forgotten the password), and deleted the partition that it was contained within. The computer now boots to this error.
Inventory: We no longer have the install disk for Windows Vista, he cannot tell me what version he used of Ubuntu, what partition it was on, any of the specs for the machine, or generally any information about the system. All I am aware of is that error on the boot-up screen. I have nothing else to work with.
I would like to remove Grub, and Ubuntu, and leave Windows intact (the request of the owner of the computer), but I have no idea what commands I could use to get rid of either when I can't access Windows, or how to properly remove them if I did access Windows.
Before I begin, here are some computer specs:
Toshiba Satellite C655
2 GB Ram
250 GB HDD
Intel Celeron 900 Joules / 2.2 GHz
64 bit
So, a little backstory. For christmas I got a new laptop with Windows 7, and while Win7 is a good operating system, I wanted to try Ubuntu and see which one I liked better. I installed the 32 bit version, because I understand people run 32 bit Ubuntu on 64 bit machines with out problems. For the first few days, everything was going amazing and I was pretty much using only Ubuntu (I had a dual boot with WIn7). One day, I opened my lid to find that the log in screen wouldn't appear, so I restarted.
I wish I could remember what error I got, but everytime grub tried to load Ubuntu, it wouldn't load, it just gave me some error (it may have been a kernel panic, not sure). So I went into windows, burned a windows repair disc, and fixed the MBR to be the windows boot loader instead of grub, then deleted the Ubuntu partition. Shortly after, I tried the 64 bit Ubuntu installation, and it wouldn't even boot up after the first boot (unfortunately, can't remember the error I got then either). So I repeated the MBR fix for Windows, and just stuck with Windows for a while. However, a new problem arose. Every now and then (and in time, more frequently) everything would freeze, for 1 to 2 seconds.
It couldn't have been my RAM or anything, the computer was blazing fast when I got it. The windows boot also took much much longer than usual, until it just wouldn't boot at all. I had my father (who's much more knowledgeable at computers) to do something, and he loaded into an earlier recovery partition ran a program called CCleaner, which supposedly fixed it. However, the problem was still there, and it got worse. I tried CHKDSK, it didn't do anything. The random freeze ups kept happing more frequently and became more and more bothersome. Eventually my computer just wouldn't boot up, it would just be a blank screen after the 'Toshiba' logo.
I eventually called Toshiba and they said that I apparently deleted the original recovery partition, and needed a Windows install disc, which I don't have so I have to buy one. Until then, I decided to just do a complete install of Ubuntu (64 bit), since I figured if I just did a complete fresh install removing everything, it would fix it. Well, turns out it had the same freeze up problem. I then tried a clean install of 32 bit Ubuntu. No luck, still periodical freeze ups, sometimes if the freeze ups are longer the screen will go grey. Before all this mess Ubuntu ran perfectly. I'm fearing that it may be my hard drive that's the problem, but I'm not entirely sure. So, is there anything I can do to restore my laptop to full health with out buying a new hard drive? Unless the hard drive isn't the problem, but I don't see what else is. EDIT: I tried memtest. Here are the results: It says 'Pass complete, no errors'. What do you guys think?
I'm using a dual boot computer which originally had only windows XP, and I added Ubuntu to make it a dual boot. I now have Ubuntu 10.04 and windows XP
I installed PHP, MySql and Apache using this guide:
[URL]
It seemed to work perfectly.
My problem is that when I shut down and restart, I no longer have the option to choose windows. Must I blank out the disk and reinstall EVERYTHING from the start, or is there any way to save this? My Ubuntu setup is much simpler than my windows, and if I MUST sacrifice one, it has to be Ubuntu, because it will be much easier to duplicate my ubuntu work than my windows work.
when i installed it the windows 7 Partition no longer works. I can see the windows 7 partition but when i click on it, it just reloads the grub boot loader. Im in college and need the windows 7 partition.
View 5 Replies View RelatedAfter installing recommended updates for Ubuntu, Ubuntu would no longer boot from Windows Boot Loader. It looks like an error about some missing NTFS4 files briefly flashes on the screen.
View 2 Replies View RelatedI've been using Linux for over a decade, so no need to worry about the obvious. I'm positive that I have my partitions/install correct. What has me baffled is that Fedora 14, which uses GRUB 0.97 (GRUB legacy) - boots Windows flawlessly every single time on the same hardware, but Ubuntu's (or the upstream Debian's) GRUB legacy do not - even though they are based on the same upstream code from the GNU Savannah servers.
No matter what I've tried I cannot get the Debian or Ubuntu version of GRUB/GRUB-legacy to boot any recent Windows 64 beyond XP (Vista or 7). All that it does is resets the computer when Windows attempts to boot, without an error. GRUB is notoriously difficult to compile, so before I try to compile code from RedHat's archives - any thoughts,experiences, similar issues - whatever?
I got ubuntu 10.04 lucid lynx along with windows (dual boot) and using Grub. On my computer, I have my C:/ (programs) and D:/ (data). I've never used my D:/ before that day that I've lost my windows partition on my grub menu. I usually use my D:/ with windows. The first time I used my D:/ to store data with linux, I lost my windows option in my grub menu. I'm not sure what I did wrong but I do want to restore my windows option in my grub menu.
After "fdisk -l",
I checked in /boot/grub and there is no menu.lst to modify. how I can get back my windows option in my grub menu ?
I installed 11.04 after Windows 7. when the GRUB boot menu starts up there is an option for Win 7 boot but it will not boot windows. When that option is selected the screen changes colour for 2 seconds and then reverts to the GRUB menu. Ubuntu boots fine.I downloaded the Boot Info Script and ran it, the results are
Code:
Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================[code].....
I have a Compaq Presario CQ60 with Nvidia GeForce 8200M graphics card. When I first installed Windows 7 followed by Karmic in dual boot I could boot into both OS. Now when I try to boot into Windows, it displays the Windows logo and then drops back to the grub menu. It may have started happening after Windows 7 installed updates. I tried reinstalling both Windows and Karmic again and it again worked initially but now Windows no longer boots. Does anyone have any suggestions about what may be causing this or how I can fix the problem without reinstalling?
View 9 Replies View RelatedI had 9.10 installed and I did an upgrade to 10.04. However I cannot see anymore my Windows Vista partition with grub.. I have a Toshiba laptop Satellite p305.This is my boot script output:
Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================
=> Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in [code].......
Whenever I select Windows 7 under GRUB, it just hangs at a flashing underscore windows 7 is installed under my first primary partition, what should the GRUB section look like for it? I can't check what mine looked like because this happened:I started up the windows 7 recover (another option under GRUB, on hd(0,3). 7 is on hd(0,1)) and it worked. I decided that i wanted to try something else before i restore my windows 7 partition to its factory state, so i exit the recovery thing. Next thing I know, my Ubuntu partition is completely gone, along with my grub.cfg files -.-
Partitions are like this in this order:
sda1: Windows 7 (can't boot into)
sda8: ubuntu (gets erased)
sda5: partition i'm going to use soon for another distro
[Code]...
oh, and by default, there was like 20 MB of free space in front of my windows partition (idk why asus did that) and when i shrunk my first partition (the windows one) it moved it all to the left -.- do you think something when wrong while doing that?
how to be able to add windows 7 to my grub menu or to even be able to boot to windows 7. I am currently unable to do it and my system just automatically goes straight to ubuntu. I've tried holding down SHIFT during startup and all that appears in my list is ubuntu entries and a memtest entry. My windows 7 files are still intact because I can see the drive through ubuntu and see all my files. I am trying to have Windows 7 on one hard disk that is 640GB and ubuntu on a second hard disk that is 160GB
[Code]...
I'm trying to dual boot Win7 and Ubuntu WITHOUT using Grub. This is to support Bitlocker encryption.
I followed this guide, and now when I select Ubuntu I get a Grub> prompt and no ubuntu.
I feel like I'm halfway there, I just need to get Grub to load correctly or something.
i am having a problem with my dual boot setup. I originally installed windows XP on a 100gb hard drive, from there i downloaded and burnt ubuntu off so i could install it on my 200gb hard drive. For a little bit i struggled to even get it to install because it wouldn't recognize my onboard nvidia graphics, i ended up having to get an alt boot disk and fix it with technique in this link:
[URL]
Now after the bios boot, my screen shuts off for awhile and takes me directly to the login screen for ubuntu. No Grub, no windows boot options, nothing. I tried booting windows by choosing it from the bios boot menu but all it does is hang at prompt and doesn't boot at all. I tried the live cd fix and reinstalled grub but nothing changed. What i think is happening is that it boots the Grub menu but it doesn't display it because of graphical confrontations. It hangs for about 10 seconds, the grub default time, and then turns my monitor back on to display the Ubuntu login screen.
I had a dual boot system with 3 partitions, Windows 7 on one partition, and Windows XP on another partition and a Data partition. I decided to load Ubuntu 10.10 on the Windows XP partition.During installation I selection manual partition, and deleted Windows XP.after successful completion of Ubuntu installation "Grub" directly boots into Ubuntu, it doesn't show me the OS selection screen. After following some forum posts I did an update grub
Code:
Generating grub.cfg ...
Found linux image: /boot/vmlinuz-2.6.35-22-generic
Found initrd image: /boot/initrd.img-2.6.35-22-generic
[code]....
Is it possible to have the Windows bootloader point to Windows 7 and a Linux partition instead of using GRUB to point to Windows 7 and Linux?
View 2 Replies View RelatedHW config is: AMD Athlon 64 X2 5000+ Black Edition, MSI 785GTM-E45, 2X 1Gb Kingston HyperX PC2-8500. I have set up GRUB to dualboot openSUSE 11.2 and WindowsXP. Initially i had set up system with defaults: CPU@2600MHz (200X13) and therefore RAM@800MHz. Both openSUSE 11.2 and WindowsXP worked just fine. Memtest86 found no problems.
But after a while i decided to change this setup to: CPU@2500MHz (250X10) and therefore RAM@1000MHz, as it promised better overall performance. And now Windows still boots and works better then before. Memtest86 still can't find any problem. But openSUSE 11.2 hangs at boot. I've suspected cpufreq governor, but changing from Ondemand to Conservative in /sys/devices/system/cpu/cpu0/cpufreq doesn't help.
I just set up a dual boot on a system with fedora 12 and XP. XP in on one hard drive (sda) and Fedora on a second hard drive (sdb).
I installed grub on the Fedora disk so as to not touch the windows disk at all.
Prior to installation, in the bios, I set the Fedora disk (sdb) first in the boot sequence, and then XP (sda) so that the grub loader would boot up by default. (If I set the windows drive first then the system bypasses grub and loads straight into windows.)
My system can now boot up into Fedora fine, but if I select windows from the grub loader menu I just get a blinking cursor - windows will not boot.What do I have to do so that grub can boot into XP?
i finally decided to updgrade from Hardy Heron to Lucid Lynx. for this i made a backup of my old install, then i couldnt find my Lucid CD so i used a Karmic one to partition my old ext3 to ext4. There were some errors but after trying a few times it worked. Installed Karmic, rebooted (worked fine), downloaded all updates - (did NOT reboot to let updates take effect) and upgraded to Lucid.
Everything went fine so far. Now when i try to boot into Lucid the system hangs, i've also got a windowsXP partition on there so i tried booting that, first grub tells me Error 29: Disk write error then trying again windows seems to boot but it takes much longer than it should and seems to hang.
Then i tried Karmic and Lucid LiveCD (which i found in the meantime) none of the LiveCDs make it to boot after about 20 minutes. (previously they worked fine)looking at the errors it seems to be something about the harddrive. Why the harddrive would stop the LiveCD booting is a mystery to me but the same messages appear when i select Recovery from the Grub menu so i guess the problem is related.
[Code]...
I am new to Linux. I have installed RHEL 5.4 on my PC with preloaded Windows XP.
Windows was set as the first boot kernel. So if i do not choose which OS to be loaded it will load Windows by Default.
Today I got an error saying GRub Loading Stage2 read error.
i installed ubuntu 9.10 for the third time on my lenovo s10e running windows xp. my first two installs went good until ubuntu tried to update gnome to the latest version and my computer went to sh grub on reboot, so on my third install of ubuntu 9.10 using wubi i turned off updates and the computer was working wonderfully for weeks until i let my netbook battery die.then the dreaded sh grub on reboot. i really like ubuntu and prefer to use it over xp.
View 2 Replies View RelatedI'm wondering about the best way to manage a dual install of Ubuntu and Windows XP.
I had Ubuntu installed on my HDD, but I wanted Windows also, so I used a live CD to partition the drive, and opened some space for a Windows partition. I installed Windows in that space. Naturally, the install set up the computer to boot directly into Windows. I want to set up GRUB to load and allow me to choose my OS on boot.
I'd like to use Super GRUB Disk to install GRUB on the MBR of the disk to allow me to choose at boot.
I HP pavillion dv2715nr with Windows 7 Professional 32 bit and Ubuntu 10.10 64-bit. I first install Windows 7 then installed Ubuntu 10.10 64 bit (grub2). And upgraded to Kubuntu. I can log on Ubuntu.
Problem: If I select Windows 7 from grub menu screen goes black and nothing happens.
Grub is gone but still there can only boot to Windows?
View 1 Replies View RelatedSo after completely giving up on linux for a year... after problems with installing grub, i reluctantly decided to give it another shot.
So I installed a new copy of kubuntu, everything worked correctly except one problem arised with my windows partition. When i try to boot windows through grub, it simply directs me back to the grub boot menu. I can boot kunbuntu fine.
I have tried recovering startup issues by using a windows 7 disc and also run bootrec.exe.
I had no problems running the command /FixMbr however /FixBoot has issues....
My partitions are as follows:
I think the problem is that grub has overwritten windows boot files so everytime i try boot windows it reverts me to grub in a sort of loop.
I installed Kubuntu 10.04-2 on a small hard drive, its in my computer along with my large hard drive which is devoted to Win XP. The Kubuntu worked fine for a while, then somehow the GRUB got transferred onto my Windows hard drive. I'd like to get the GRUB off my Windows hard drive and have that boot via its usual Windows method. I reformatted my small / Kubuntu hard drive, that did not help. In fact this made things worse, now there is no Kubuntu in my computer, so now I can't get into either Windows or Kubuntu. How can I get rid of the GRUB AND have Windows boot up normally?
View 7 Replies View Relatedi've a little problem with the grub loader. I've two OS in my laptot: Ubuntu 9.10 Karmic Koala 64bit and Windows 7 64bit. But i can't boot Windows 7 from the grub loader. The grub still load the /dev/sda1 partition that is the recovery partition of the laptot, while windows 7 is in the partition /dev/sda6. I tried to modify the path in the grub.cfg, but still load the wrong partition, how i can do?
View 2 Replies View Related