Ubuntu Installation :: Dual Boot 10.10 And Windows 7 On Seperate Drives?
Mar 8, 2011
I am trying to install ubuntu 10.10 and windows 7 on my hard drive. I want to install both the OS on seperate drives. can anyone tell how to do it? I know that there are screenshots on ubunutu site itself but i am new to ubuntu and I am unable to follow instructions.
I first installed ubuntu 10.10 in dec 2010 using my ubuntu dvd. Now I am reinstalling it again but the setup screens have changed? hows that possible? i mean its the same disk. does anyone know why? or am i drunk.
View 4 Replies
ADVERTISEMENT
Jun 21, 2010
I'm a n00b at dual booting and I plan on installing Ubuntu 10.04 on a separate hard drive than my Windows 7 64 bit one in a dual boot situation. I have read that you can do this by unplugging the Windows hard drive, install Ubuntu on the other one, and than plug the Windows hard drive back in and everything will be fine and dandy. Is this correct? If it is, will I have to manually set the Primary and Secondary drive (in the BIOS I think?), or will it automatically do that.
View 6 Replies
View Related
May 1, 2011
I've used it once before but got fed up with the boot asking me everytime I turned my laptop on because I wasn't using it enough. I have Windows 7 on drive C . I want to keep it on drive C. I have several 1.5TB+ drives, and one of them is not being used. I want to dedicate it to Ubuntu, and be able to do a dual boot with my Windows 7 install. Is this possible? If it is, what about when this drive is not connected to my laptop? Will that mess up the boot process?
View 2 Replies
View Related
Jun 25, 2010
Ok so first off my hardware Asrock 775dual-vsta Master and Slave hard drives on primary IDE Absolute Linux 2.6.33.3 ; Dos 7.1 (yes Dos 7.1 by itself no windows whatsoever) Absolute Linux=sda1 ; Dos=sdb1
Ok so I can't boot into dos from lilo boot menu. It boots fine however if I tell the bios to boot from the second HDD first (DOS). But it's inconvenient to tell the bios every time on power-up to choose the second hard drive as the first boot device. Here is my lilo.conf boot section
# Linux bootable partition config begins
image = /boot/bzImage
initrd = /boot/initrd.gz
root = /dev/sda1
[Code]...
Either way when I boot from the first hard drive (linux hard drive) and lilo pops up, I select dos and hit enter then nothing... It just sits there and ctrl-alt-delete can't reboot my comp as it's frozen.
I don't wanna have to tell the bios to select my dos hard drive as my primary boot device everytime I wanna boot dos. I wan't my linux hard drive to be my primary boot device and have my dos hard drive selectable from the lilo boot menu. Why can't I do that? What am I doing wrong? I thought this was easier than dual booting from a single hard drive?
View 5 Replies
View Related
Aug 25, 2010
I have Vista installed a 500 gb and recently added a 320 gb hard drive. How do I install ubuntu on to the 320 gb HDD and be able to dual boot the 2 operating systems? Also how do I keep myself from getting the symbol 'grub_puts' not found error when updating to 10.4?
View 5 Replies
View Related
Jul 3, 2010
I have installed winxp & ubuntu 10.04. But i cannot find my windows drives from ubuntu 1.04. how can i watch my windows drives from ubuntu 10.04
View 3 Replies
View Related
Mar 18, 2010
I have Windows XP installed. And I also plan to install CentOS 5.4.I have two hard drives. Hitachi 500 GB and WD 500 GB.Windows XP is intalled on first drive And I plan to install Linux on Second drive. And since i find some contradicting and not understood by me posts. I have to be sure what to do. I can install Linux, then i can edit grub. and add there something like:
title Windows
map (hd0) (hd1)
map (hd1) (hd0)
root (hd1,0)
chainloader +1
When its on one drive as I understand it will definately work. But if its on 2 different drives. There is a problem that windows doesn't boot from secondary drive. So I find this article witch i cannot understand. Do i have to understand it? Or its wrong and bad decision.
[URL]
I have no RAID.After all what is step by step process of creating bootable CentOS and Windows situated on different hard drives drives?
View 19 Replies
View Related
Nov 23, 2010
I just started working with Linux over the weekend. I do have a working dual booting system but it's not configured exactly how I want it to be. Currently Windows 7 Ultimate and Ubuntu are on the same hard drive but different partitions. The Windows boot screen comes up and I can select Windows or Ubuntu fine. Grub comes up when I select Ubuntu and I can successfully select any choice in the menu and it will run properly.
Everything works great now so you may wonder why I even want to keep tinkering, well, it's not working how I want it to. This is what I want it to do. I want Windows 7 on disk 0 and Ubuntu on disk 1. I want each OS to have it's own hard drive. I want Grub to be the only boot loader that comes up with the option to select Ubuntu or Windows. I want to skip the window's OS selection screen all together. I can modify Grub, I've already done some of that on my work computer.
I've been installing from windows. Should I use a CD instead? Would that accomplish my goals without doing anything special?
View 3 Replies
View Related
Oct 7, 2010
We were trying to install w7 on a reserved partition. W7 did not like the partition (whatever we tried).
Since we had 3 hard-drives, on the allocated drive we deleted all partitions and set the partition table type new to MSDOS (yast etc.....).
W7 installed fine. We did not time it, but it appeared that 11.3 installs faster plus considering 11.3 installs quite a number of applications.
There are plenty of postings re integrating W7 to the Grub-menu.
This system went through several Suse updates, hardware upgrades, basically was all over the place.... we did a "new" install of 11.3 allocating its own hard-drive.
Install......fine, and Grub entered W7 to the menu. Worked ! Mounted the windows partition to /home/yourusername/windows
So, if you really (?) need W7 and have a spare hard-drive, this maybe is a clean solution.
View 7 Replies
View Related
Dec 10, 2010
recently sent up another computer as follows:Two sata drives. Windows 7 was installed on the first drive(sda)and booted successfully. This drive was disconnected ( I have had some installs where Unbuntu wipes out the existing C drive eventhough I am installing to D) and Ubuntu was installed to the second drive (sdb). At one point I had to rebuild the grup on the Ubuntu drive and was careful to make it installed on the Ubuntu drive. To my surprise when the PC booted up I saw the Grub menu with a menu entry for Windows. The Windows drive was always the primary drive before the Ubuntu install. I was planning on the Windows drive being the boot drive and using a boot manager to determine where to go from there. If I utilize the BIOS boot option (F12) I can boot each drive individually. I cannot in BIOS set a particular drive to boot - just a hard drive. Everything is working I am just curious why the primary drive does not boot first. IN BIOS the Windows drive is a primary SATA with a lower number that the Ubuntu drive which is listed as a secondary drive.
View 4 Replies
View Related
Feb 15, 2011
I can only use the Live CD to operate Ubuntu. After typing in the command sudo fdisk -l, I get the following?
Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
[Code]....
And when I boot without the Live CD, I get the following message in the GNU GRUB Version 1.98-1ubuntu7 window page.
View 9 Replies
View Related
May 31, 2010
I have tried (a few times now lol) to get this setup. I am using Windows 7 64-bit and Ubuntu 10.4 64-bit. I have Windows 7 installed on one hdd, another hdd has the System Reserved partition along with a data partition for files, the third hdd is the one where I want to install Ubuntu. I have found numerous tutorials on installing them both on the same drive, but not on separate ones. The couple I have found haven't really worked.
I think that Ubuntu is installed correctly but there is no option to boot into it. Windows 7 just happily loads itself. I have tried reinstalling and selecting 'sdc1' (the native ubuntu partition) as the location for the bootloader to be installed and then used Easy BCD to add that location to the windows bootloader which gives the option to load Ubuntu but when selected dies complaining that there is a missing file (I think it just can't find the Ubuntu bootloader).
As an aside when I get to the installation screen the Ubuntu installer keeps on telling me that there are no operating systems detected on the machine (Even though I'm pretty sure the drive it is talking about 'sda' is where Windows 7 is installed). Not sure if that matters just seemed a little wierd.
View 7 Replies
View Related
Aug 25, 2011
I have been messing around with the ubuntu family for some time now, and usually have no problem finding my answers. This one, however, is giving me some trouble. I have been using ubuntu on my laptop for some time now, and recently got a new 2TB hard drive for my desktop. I cloned the old hard drive to the new one, and decided to install ubuntu onto a third drive. The third drive was IDE, the new one is SATA. I disconnected the other hard drive, and so my current set up is a SATA drive with Windows 7, and an IDE drive with Ubuntu (11.04 of course)
Well, I am unable to dual boot between the two, unfortunately, and would like to figure out how. I would like to say the problem is with Windows, since that is the primary drive. No GRUB shows up upon booting when both drives are plugged in, and the Windows Bootloader does not show my installation of Ubuntu, instead it goes right to Windows.
View 4 Replies
View Related
May 1, 2010
this may be a very stupid question, but. My computer has two hard drives. One has Windows XP installed on it. The other is blank.
Is it possible for me to install Ubuntu onto the second hard drive, and run a dual-boot using GRUB during startup? Or does it only work when both OSs are on the same hard drive?
View 1 Replies
View Related
May 4, 2010
I would like to install Ubuntu 10.04 on my new 1 TB hard drive. I currently have Windows XP installed on a 160 GB hard drive for things that I cannot do on Ubuntu. I would like to know if it's possible to install the other hard drive, and then dual boot Windows with it? Effectively dual booting across two hard drives. I wouldn't care if GRUB replaces the standard Windows bootloader, just as long as I can choose between the two at startup
View 9 Replies
View Related
Jun 4, 2011
I have Ubuntu 11.04 on 1TB HDD and Win 7 on another 1TB HDD. Right now I have to unplug a SATA cable to get to boot into one or the other. What is the best way to be able to pick. I don't care which OS I do it in or which is the primary, if there has to be one. I have an MSI mobo.
View 2 Replies
View Related
Aug 9, 2011
I've been using ubuntu exclusively on my two laptops lately, for coding and all of my other work. I plan on installing it onto my desktop now for work as well, but I would like to retain Windows 7 so I don't have to worry about compatibility for all of the games I love to play. My question is this:When setting up my partitions, how much space (and what format) should I set aside for windows to write and read games from? I have a 500GB hard drive currently, and was planning the partitions as:
1. Windows 7 (NTFS, setup with Windows installer) ~20 GB
2. File Storage (NTFS, set up with the Ubuntu install partitioner) ~452 GB
3. Ubuntu (EXT3, set up with Ubuntu install partitioner) ~ 20 GB
4. Swap (~2x the size of my RAM) ~ 8GB
The plan is to have Windows install and execute games from the NTFS File Storage partition, while being able to access the same partition from Ubuntu for my documents, code files, music, etc.I don't know if this would work, and I'm also not sure what my file system will be like (windows or linux-y?) if it did. Will this work? Or is there a more elegant solution?
View 7 Replies
View Related
Apr 14, 2011
I have recently built a new system which has two internal sata drives. The plan was to install windows 7 one drive and ubuntu 10.10 on the second drive for KVM hosts. I started with the windows install which completed, then I went forward and installed ubuntu 10.10 64bit to my second drive (sdb). During the installation I chose to manually partition my drive. i partitoned the drive (sdb) as follows
/boot - 1gb
/ 40gb
swap 16gb
extended partion of 400gb
I then selected sdb to hold the boot record, as it was set by default to sda (my windows drive). The OS installed fine. I then went to reboot my system so go back into windows, by selecting the first drive in the bios. Once selected the system keeps booting into Ubuntu, no matter which drive I select. Now I checked the grub.cfg file and i see all references to hd1 there is no reference for windows found. I then proceeded to do 'sudo update grub2' this did not pickup any reference to my windows droive to add to the grub menu. When i select the ubuntu drive to boot fom my bios, i get no grub menu appaer it just boots quite happily into ubuntu. Can anyone please provide any resoloution to this, I can provide additonal outputs regarding my partion tables etc. later this evening when I get back from work.
View 9 Replies
View Related
Jun 8, 2011
Is it possible to create a dual boot system from two separate disk drives each having been created as a single boot computer? I have an 80gb disk drive with Windows XP installed on it. I have a 160gb disk drive with Ubuntu 11 installed on it.
I have installed the Windows disk drive as drive 0 and the Ubuntu disk drive as drive 1 in my computer. Each disk drive was set with cable select pin settings. The computer boots to windows. If at all possible, how would I go about setting up the system to dual boot to both windows and Ubuntu? I have attached screen shots of part -l, gparted 80gb disk and gparted 160gb disk.
View 4 Replies
View Related
Jun 4, 2010
I have the following PC set up:
Dell 8400 with 3 GB of RAM with 3 160 GB SATA drives:
The first one has Windows XP installed on it.
The second one has been newly formatted and Ubuntu 10.04 has just been installed on it (20 GB / and 6 GB swap) with grub being installed on the first partition and not the master boot record. The remainder will be for storage for Windows.
The third drive is simply storage for Windows.
At this point I am able to boot XP just fine, but I'm not able to boot Linux. I just getting a blinking cursor or the PC just reboots when I choose Linux. I believe I have set up my boot.ini properly using:
C:Bootsectc.lnx="Linux Ubuntu"
After running dd if=/dev/sdc1 of=bootsect.lnx bs=512 count=1 and putting that file in place.
For reference, I don't believe this is a Linux problem, as much as I am simply trying to guide the ntldr to be properly pointed to a place where it can boot Linux. When I go into the bios and disable the first and the third hard drives, grub pops right up and I'm able to boot Linux with no problem, so that piece is fine. I think it's just now trying to get the correct syntax so I can boot Linux without having to disable drives and reenable them.
For kicks I even tried these syntax types in boot.ini:
multi(0)disk(0)rdisk(1)partition(1)="Linux11"
(i.e. 2nd disk, 1st partition ...etc...)
I read many troubleshooting documents on dual booting and so forth but I just can't get this right. For reference, I stated the way XP views my Hard Drives in the intro, which seem to be a different order than Linux sees them, yet I believe I've tried all the combos of settings for this to work (yet clearly have not). I have attached the output of boot_info_script*.sh here: [URL]. Boot Info Script 0.55 dated February 15th, 2010 ..... Devices which don't seem to have a corresponding hard drive.
View 9 Replies
View Related
May 29, 2011
I've been trying to properly install grub for the past 3 days and failing every time.I recently bought a new computer and would like to dual boot Windows 7 64 and Natty. On my previous machines, ubuntu installer has automatically detected windows. It does not do so on this machine.I have three hard drives: 2 ssd's and a single 3 tb drive for storage.
I would like one ssd for windows 7 and one for natty.Currently, I am able to boot into both OS's but only by altering the boot sequence of the drives from the bios. I am hesitant to install grub to the windows drive for fear I will lose the ability to boot into windows. I did this early in the discovery process and ended up having to reinstall windows.
View 9 Replies
View Related
Jun 17, 2010
I need a suggestion on setting up a dual boot menu for my setup. I have two hard drives one with WinXP and a second one with CentOS 5.3 installed. I basically moved the hard drive from another identical machine to this one and so I want to setup a boot menu to access either windows or Linux. CentOS already has grub on it.
What is the simplest method of setting up the dual boot menu? I would like something which is easy to administer which I can just ghost over either the Linux drive or Windows drive or disconnect either and have either boot just fine. I don't ask for much do I?
If I have to go through a little process after ghosting over one or the other drives that would probably be ok. We get updated images for this machine and replace the image on the drives with new images, although Linux shouldn't be reimaged, just windows. So the Linux drive (2nd drive) should not be touched normally.
View 9 Replies
View Related
Feb 9, 2009
i'm tying to dual boot Vista64 (already installed) and Fedora 10 x86_64. I am running a Dell XPS 410 running 2 sata hard drives raid 0 (ICH8DH). I started the process by shrinking my C drive on disk0 leaving 64.45GB of unallocated space. Next I rebooted into Fedora install DVD and when i get to blue graphical install screen i get message asking if my drive is GPT and if it is it may be corrupted. I click NO, and it comes up with a message telling me i have to initialize my drive if i want to use it ( have to click NO twice) and if i do it i will lose all my data.
i can click no and keep proceding through the install until i get to the partition setup screen. No hard drives or partitions are shown. I've tried googling the problem and get bits of pieces of information scattered in different parts but nothing conclusive to my problem i think. As far as my background of knowledge goes, I'm new to the linux community but give me a thorough guide and i'll do fine (i hope). I've been using fedora on a separate laptop for 2 days now .
View 9 Replies
View Related
Feb 28, 2011
I am new to Linux and was wondering how to make dual booting Windows and Ubuntu from 2 separate drives work. I have dual booted from the same drive but never different ones. If I install Ubuntu on the second drive how will I configure the system to let me choose on start up?
View 3 Replies
View Related
May 24, 2010
After attempted upgrade on my dual bot drive I can no longer boot Windows XP or either of my 2 sata drive.
View 5 Replies
View Related
May 7, 2010
I had 9.10 installed and I did an upgrade to 10.04. However I cannot see anymore my Windows Vista partition with grub.. I have a Toshiba laptop Satellite p305.This is my boot script output:
Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================
=> Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in [code].......
View 3 Replies
View Related
Feb 3, 2011
I have a motherboard with the following chipset Intel 945GM + Intel ICH7R Chipset
This board: http://emea.kontron.com/products/boa...6lcdmmitx.html
I have two 320GB HDDs setup in hardware raid as shown below. But in gparted they are showing as two seperate drives. Why is this?
Raid setup:
GParted
fdisk -l
What am i doing wrong here?
View 8 Replies
View Related
Apr 30, 2010
I just did an upgrade from 9.10 to 10.04 and now I can't boot into Windows 7 on this dual boot desktop. I usually do a clean install but with a laptop and desktop a copy of Windows 7 and Ubuntu on each machine it's getting very tiring with 4 os's so opted for the upgrade this time.
During the installation there was a window that game up about upgrading grub and what devices to install it on. The help box was not very complete and seemed to say to click all the check boxes which included the main drive and it's partitions including windows. During the install somewhere it said something like grub could not be installed on one of the devices which I think was sda6 which is probably the Windows 7 partition.
So how would I get the option of booting into Windows 7 on startup as now I only get a blank black screen when I click on the Windows 7 option upon bootup? I hope I don't have to reinstall one or both os's again from scratch as this is becoming to much work to do on two systems every 6 months, especially with the amount of programs I have installed.
View 9 Replies
View Related
Mar 23, 2010
I had a dual boot machine with fedora 12 and windows vista and I could use grub boot-loader to switch between two. Few days ago windows got corrupt and I have to reinstall it. I put windows 7 now and as usual it erased grub. So to reinstall I put the fedora 12 installation CD on and followed some usual setup steps. When I got the command line I issued the command "grub-install /dev/sda" (sda not hda because It showed bunch of sda, sda1..) but surprisingly it said grub command not found. I remember doing it before while it worked fine.
View 4 Replies
View Related
Jul 8, 2010
I have a netbook running Windows XP as standard. There is also a recovery partition which came from the factory.
In the past I installed Ubuntu (I think 9.something) from USB key and all worked fine. However my XP became corrupted and I needed to do a repair on it. After this, Ubuntu became removed from the boot select menu.
Since then, Ubuntu has become updated to 10.04, which I now cannot install.
The Live CD tells me there is a "file IO error" and simply stops installation at around 70%.
I did manage to get into Ubuntu from a Live USB using Wubi. However when I chose to install Ubuntu to a Harddrive, the option to "install side by side" was missing.
After reading on the forums, I did a chkdsk /f on Windows and tried again. Now my liveUSB does not show a boot menu!
When I select to boot from USB stick, the screen goes blank with a flashing cursor. Ctrl+alt+dlt reboots.
I'm really lost here! It seems when I fix one problem, another problem arises!
Also when trying to instal Ubuntu within Windows, the process goes through to 100% and asks me to reboot. When I do so, the option for Ubuntu does show in the boot menu. However when I select it, I get an error "Windows boot failed: file wubildr.mbr and status: 0xc00000f - something is corrupt".
View 1 Replies
View Related
