Software :: Installing ATI Radeon Card In Existing Fedora 12 System?
Aug 23, 2010
After lots of trouble with the new Nvidia stuff in Fedora 12 I gave up and am trying to switch to an ATI Radeon 4350 card in the existing system.I have removed the Nvidia refs with rpm -e, deleted /etc/X11/xorg*, and installed the card. I am only able to get a maximum resolution of 1024x768. Here's what I've done:
Boot and su/delete all refs: /etc/X11/xorg*
Reboot. System comes up with 1024x768
Select Administration->Display to run system-config-display.
Su/password dialogue
[code]....
If I try to add a mode line following Depth 24, It is ignored by system-config-display and overwritten. This worked with the Nvidia installation and I was able to select my resolution above 1024x768.
View 13 Replies
ADVERTISEMENT
Feb 7, 2010
I am trying to use an ATI Radeon x300 graphics card with my current system setup with fedora 12 but i am having an openGL issue. I am trying to create a 3D model using comsol and i get an error like:
Failed to initialize 3D graphics. OpenGL not fully supported.
This is a hardware/software issue with the graphics card... not the program COMSOL. How could i enable openGL support to correct this issue?
View 2 Replies
View Related
May 13, 2010
I have two SAS RAID controller cards in a Dell server in slots 2 & 3, both with an array hanging off them. I went to install a third card into slot 1, but then when it boots it says two of my sd's have bad magic number in the super-block and it wants me to create an alternative one, which I don't want to do. If i remove the new card, the server boots perfectly like it did before I added the new card. Is the new card trying to control stuff that isn't hooked up to it because its in slot 1, so its confusing RHEL?
View 5 Replies
View Related
Apr 18, 2010
I have a lenny system up and running, my CF-card reader is supported and I can mount a 1GB card. My PC _can_ boot from CF cards, I verified... My Linux resides in sda3 (other partition is XP). How would I transfer the partition to a cf card? I tried using dd if=/dev/sda3 of=/dev/sdb1, but as that doesnt work I have the feeling there's more to do... Maybe install GRUB on the CF-Card? Change some paths after copying?
View 6 Replies
View Related
Jun 29, 2011
After a bit of work I got 3d acceleration (direct rendering) working on my system. Now, whenever I use intensive graphics, (certain screen savers, Google Earth overlay animations) all performs fine for a while (1-2 minutes) and then causes a full system freeze. Only solution at that point is a hard power reboot. I don't know where to look for a solution, since I can not check any diagnostic files when the system is frozen.
System:
Intel Pentium 4 CPU 3.00GHz
ATI FireGL V3100 graphics Card
OpenSuse 11.4 with radeon driver.
View 9 Replies
View Related
Oct 29, 2010
just like most Linux distributions, will happily co-exist on a hard disk with just about any version of Windows. This is a concept known as dual-booting. Essentially, when you power up your PC you will be presented with a menu which provides the option to boot either Ubuntu Linux or Windows. Obviously you can only run one operating system at a time, but it is worth noting that the files on the Windows partition of your disk drive will be available to you from Ubuntu Linux regardless of whether your windows partition was formatted using NTFS. To day I have installed Latest Windows 7 and Latest Ubuntu 10.10 on my office system (Dual booting). This two operating system which I installed in HP dx 7200 micro towers.
System Information
Operating System: Windows 7 Ultimate 32-bit (6.1, Build 7201) (7201.winmain_win7ids.090601-1516)
Language: English (Regional Setting: English)
System Manufacturer: Hewlett-Packard
System Model: HP Compaq dx7200 Microtower
BIOS: Default System BIOS
[Code]...
View 3 Replies
View Related
Apr 20, 2010
I have fedora 12 currently installed on my laptop, but would like to install another version along side it. How do I do this? Will it detect the second version automatically and add a grub entry? Or do I need to do something else. Also, what partitions need formatting, do any new one except '/' need creating?
Current layout>
/dev/sda1 ext4 /boot 200 MB
/dev/sda2 ext4 20 GB <--- I want to install new version here.
/dev/sda3 ext4 / 20 GB
/dev/sda4 extended 425 GB
/dev/sda5 ext4 /media/Media 425 GB
View 3 Replies
View Related
Feb 10, 2010
I just installed fedora12 on my machine,But it didn't recognize to my graphic card! my ATI card type is radeon 9550.
View 6 Replies
View Related
Mar 1, 2011
I am thinking about buying a new computer. It has ATI Radeon HD 3000 Graphics. Does Fedora 14 support ATI Radeon HD 3000 Graphicst? Will I have to install a driver and if so where would I download the driver?
View 4 Replies
View Related
May 20, 2011
Well I've been trying to get drivers installed for this card for a few days now and I can't get anything to work. The proprietary drivers for this card don't support the xorg version installed in F14. I've tried mesa and ati drivers but I can't get them to actually work, they both just cause x to crash during startup. I've looked through the threads for ati drivers but they all seem to talk about using the latest catalyst drivers and thus non of them have helped me much.
View 3 Replies
View Related
Jul 4, 2011
Right so my situation is a little obscure and from all the posts I've read through I can't find one that suits me well enough.My PC's hard drive recently went on the fritz so I backed up all my data, got a brand new Terrabyte hard drive and then put all my stuff on there. I also plugged in the fault drive as a secondary and ahev cleared most of the stuff off it. It's separated into two partitions; E: and F: but together make about 600 gigs. I then have two external Terrabyte hard drives, it's a long story but their connected via USB.
Now I really like the idea fo getting to grips with Linux. I don't want to use a LIVE CD, I've done that already and I want to see how I get along using it as a proper OS. I also really need to keep the Windows Vista for several reasons, most importantly for iTunes which I use to keep my iPhone and iPad up to date and I've heard iTunes and linux don't get along too well, even with programs like WINE. So obviously I'm looking to dual boot and keep all my data but what would be the best way to go about it? Stick it on my primary drive? Or on my slightly faulty drive? Or on one of my two externals? On the bright side, because I'm on a fairly new hard drive, my Vista runs really smoothly, and so I shouldn't encounter too many bugs that windows is renowned for a long the way...
I'd also like to be able to access all my data from both OSs so I don't have to keep jumping from one OS to another. Is that possible? or simple to accomplish?I have a pretty good Nvidia graphics card too, so I'd appreciate it if someone could explain how I get XGl working on Fedora once it's all set up.
View 8 Replies
View Related
Aug 10, 2009
I've loaded Fedora and must say what a nice OS! But I'm having some issues getting the video working correctly so let me jump right into the issue. The video is very garbled and hard to read. can't seem to find a way to correct what would appear to be a driver issue. Here are a list of things tried:
- display works fine with Ubuntu
- display is clear but is chopped off when using an external monitor from onboard vga slot
The video card is an ATI radeon and the linux drivers from the ATI site don't work with the new images that are out yet.
View 3 Replies
View Related
Mar 29, 2011
Will Fedora 15 support this video card on laptops?
View 2 Replies
View Related
Jun 14, 2011
The display card of my notebook is ATI rd 6370m ,the OS is fedora14. After I installed the driver download from ATI web site, it says that my computer can only run 2D can't run 3D. I want to know if some one used the same card with me in fedora14 has run 3D sussesfully? After the installlation I run "#aticonfig" it says "can't find the adaper".
View 2 Replies
View Related
Jun 5, 2010
I have acer laptop with ATI Mobility Radeon HD 5470 graphics card. I have downloaded ATI Radeon 5xxx driver from ati official site. When I ran it using the command below, it gives me the following error
command:
Error:
Removing temporary directory: fglrx-install.OiFpw4
View 14 Replies
View Related
Dec 14, 2010
I have ATI graphic card with HDMI video and Audio:
I see that I have HDMI connector and S/PDIF connector on the mortherboard, I just have HDMI connector on the monitor, I have no problem with the video but the audio does not work, I just want to confirm that the audio should also go throught the HDMI cable right ?
Here is the output from the alsa-info.sh script.
View 1 Replies
View Related
Jul 21, 2010
I have an EeePC 4g netbook which only has a 4Gb hard drive and I thought I would like to install Fedora 13 on an 8 Gb SDHC card and use it to boot the netbook.
As neither the netbook nor I have an optical drive, I made a bootable USB memory stick using Unetbootin which boots the netbook and could be used like a live CD to install Fedora.
On booting with the live USB stick, with the blank SD card in place, and clicking on the install icon, the installation starts but then there are 2 problems; the first is that the installer appears to want to install to both the SD card and also the USB stick. There is a tick in the box beside the USB stick which I can't remove.
I decided to ignore that and put a tick in the box beside the SD card but when it got to the point where it creates partitions it said "Could not find enough free space for automatic partitioning. Please use another partitioning method"
Surely 8 GB is more than enough space for partitioning, so where am I going wrong and why does it want to install on the USB stick as well?
View 2 Replies
View Related
Jul 31, 2011
I have an existing Fedora 15 system installed from scratch.I've ordered a harddrive identical to my SDA and want to add it to my existing system as a RAID1 setup.I've googled around and cannot find recent clear instructions how to accomplish this. I don't want to reinstall everything from scratch. It should be possible to create the RAID1 using the existing data disk and then mirror everything up?
View 1 Replies
View Related
Feb 19, 2009
I have recently installed Fedora 10 in my x86_64 system and fully updated. The updation size was nearly 650MB. My question is can I make a an updated installer DVD from my existing fedora system?
View 8 Replies
View Related
Jun 22, 2010
I've had such good luck with Fedora (and this Forum), I'm attempting to put F12 on wife's brand new Sony Vaio, a VPCEB11FM, a 64bit system. I downloaded the Fedora-12-x86_64-netinst.iso, made sure it was ok with sha256.exe, then burned the image to DVD. Booted it up and let it default to "install or upgrade an existing system". It dead-ended in a dark blue or black screen. I re-started and examined the other options. Thought I'd try the one that says: "Install system with basic video driver". Got all the way through to where it got ready to start downloading files. Can't get past that point because it attempts to get to the Internet using the Sony's wireless card! Why would it try the wireless when there's a wired NIC card in this PC that requires no special driver etc. How to proceed from here?
View 3 Replies
View Related
Apr 6, 2009
I want to find out how to create a Fedora installation CD from an existing Fedora System. I cant find my CDs and I want to set up another system. What commands do i use or how do I go about it.
View 1 Replies
View Related
Apr 4, 2010
I replaced an ATI Radeon 9550 with a Radeon X1300/X1550, in hopes of better performance.
My System: P4@3GHz, 1.5Gb RAM, Fedora 12, kernel 2.6.32.10-90.fc12.
Faults: Screen refresh is extremely low. Glxgears outputs 25 FPS. Dragging windows around is sometimes really slow.
What I did so far, in hope of fixing it:
1. Installed 'system-config-display', for providing an xorg.conf
2. Did: yum --enablerepo=rawhide update mesa-dri-drivers-experimental mesa*, fixing this, but to no avail...
I cannot find any errors in the log...I don't know what to do...
I am posting my Xorg.conf, Xorg.0.log and Glxinfo through links to pastebin.com
POST UPDATE:
When running GlxGears, I get a bit of motion, and then the gears freeze for 1 second. And this goes on and on. But...if I move the mouse around, I get 1100FPS!
Now I messed a bit with xorg.conf and the "SWCursor" Option, but the above happens when this option is on "true". On "false" there is no 1100FPS, only the freezing loop...
View 1 Replies
View Related
Apr 21, 2010
I'm looking at buying this card and I'm wondering if anyone here has had an issue using this card with Ubuntu(currently on 9.10)
[URL]
View 3 Replies
View Related
Sep 16, 2009
I had some problems with ububtu because it doesn't work very well with Intel cards. Anyway I've downloaded Fedora 11 and Now i am using it without installation. I'd like to install it over ubuntu I have to choose this option right ? "replace existing using system"?
View 8 Replies
View Related
Mar 28, 2011
i am trying to install asus usb wifi card WL-167g v3 in fedora 14. but i am not able to install it properly.
View 4 Replies
View Related
Apr 26, 2011
I sudo apt-get uninstalled a bunch of stuff I shouldn't have. Now my Ubuntu Partition doesn't boot up correctly, something about the graphic system, video system, etc. all being unconfigured. (I'll get the exact error later.) All I can use is the command line.can I install Ubuntu over my old Ubuntu partition without messing up rebooting/GRUB and all that?
View 3 Replies
View Related
May 12, 2011
I have a Radeon HD 5830 card and it just doesn't seem to be working to it's full potential. I've tried TF2 and SC2 through the latest stable release of Wine, but the frame rates are horrible.
Also, when I run fgl_glxgears, I only get 800fps. (If I reboot the computer and run fgl_glxgears as soon as I log in, I get at least 3000fps for a few seconds. Then it's back to 800)
I've tried reinstalling the driver several times.
Why is the performance so low?
Here's my setup:
XFX Radeon 5830
Ubuntu 11.04 (fresh install and updated)
11.5 ATI driver from AMD's site. Here is fglrxinfo output:
[Code].....
View 9 Replies
View Related
Apr 14, 2010
I had a problem with OpenGL on my computer (I run Ubuntu), and so I created a thread here: [url] but it turned out that the problem was with my graphics card, so I made a new thread at the Ubuntu forum at [ubuntu] Problem with OpenGL in Ubuntu - Ubuntu
View 4 Replies
View Related
Aug 6, 2010
I decided to put a Radeon 8500DV card in my Slackware box. Works fine with the Vesa driver. Problem is, I'm using a widescreen monitor, and Vesa doesn't support my default resolution (1366x768). So I thought I'd do a little editing in my xorg.conf file and fix it right up.
I logged on as root, and did "X -configure", then I went in and edited the file it made me and put in the appropriate values for my monitor and resolution. And then it copied it over my xorg.conf file, and typed startx. Voila! Looked great, and I checked the settings to be sure I was in 1366x768. It worked fine!
Once.
Then I logged out and tried "startx" with my user account. As soon as I do, my monitor displays "No Signal"... weird - cause it just worked. So I rebooted, and logged on as root, and tried startx again. "No Signal"
So why would it work just once and not again. I tried repeating my steps exactly, and still can't get it to come up.
Here is the xorg.conf I used when it did work:
Quote:
Originally Posted by xorg.conf
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/local"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/OTF"
[Code].....
I tried removing the Card1 and Screen1 sections (since they are invalid), but that made no difference.
View 14 Replies
View Related
Dec 15, 2010
I have installed a 9200 Radeon (the card says 9250 on it, but computer reads as 9200) on a AMD Sempron 2500+ 64 bit,Ubuntu 10.04 Gnome 2.30.2, Kernel Linux 2.6.32-26; Samsung VGA 941BW monitor.
A friend told me if I added more RAM (512mb), the card would run properly & the graphics would be stellar.
He also told me the drivers were installed.
When I did this & started the computer, before I got to my login, a box appeared, telling me my graphics were running in "Low Mode", & do I want to configure them. When I said "Yes", it told me to restart. When I did, nothing happened & the video card is still running on "low". I checked the fglrx info, and was told "command not found".
View 2 Replies
View Related
