Following a reinstall of debian amd64 lenny I am unable to get 3D acceleration (which was working fine before), although all checks are positive:
###########
francesco@tya64:~$ glxinfo
name of display: :0.0
display: :0 screen: 0
[code]....
I'm having problems with my video card (Radeon X1600) ever since I upgraded to 10.04 (video is fine until I stress the video card (eg using 3D acceleration)). This appears to be a problem with the drivers for the video card. I've had problems in the past with video cards (many because I didn't check that the card I'm buying is "Linux friendly" or not. Now I'm doing my do diligence and asking the community what video card I should buy to replace my current one? I have the following Motherboard: [URL]
View 9 Replies View Relatedi have an msi x320 (damned netbook). it was working with karmic, but no video acceleration and no wireless. i decided to update to 10.04 before installing drivers for video and wireless. but all went wrong each time i boot stuck on blank screen. haged in something if i did the same in recovery mode stuck in endless:
mmc2: controller never released inhibit bit (s)
mmc2: card removed during transfer!
mmc2: reseting controller
mmc2: timeout waiting for hardware interrupt
and never get to desktop i updated to 10.04 and this happened i loaded 10.10 netbook remix onto my flash drive, and tried to load and make fresh install but no go, very same error im using my flash drive now with 9.1 netbook remix (dont like it btw) ill use 9.1 desktop later.. to reinstall its working well i end up giving up fixin 10. something ill install 9.1 but i need firs to back up the old home folder, but need to change permision to do it...
I have an HP laptop with an ATI 4300 HD built-in. When I play avi/divx video in fullscreen, this is kinda choppy sometimes. I use the ATI proprietary driver: How do I enable hardware video acceleration for this driver?
View 5 Replies View RelatedMy system is a 2.0Ghz Dual Core PowerMac G5 Ram 16Gb - 2Tb HDD - It is running Jessie 8.3 [new Install] and seems stable enough.....! My system is showing the message below on boot up, but I don't know why? I have had to disable the 3D video acceleration with a Yaboot parameter "nouveau.noaccel=1' to get the system to load KDE. I am also having some bluetooth headaches (along with many other people apparently).
# systemctl systemd-modules-load.service
Unknown operation 'systemd-modules-load.service'.
root@Apple-Desktop:~# systemctl status systemd-modules-load.service
â— systemd-modules-load.service - Load Kernel Modules
[code]....
I installed Lenny on my HP/Compaq nx6125 (the Sempron 32 bit model). Although X is running OK, I can't get video acceleration working. Games like Nexuiz are unusable, and programs like Stellarium and Google Earth simply fail to load. i attached some information below.
Currently, I had the free radeon driver installed. The non-free fglxr drivers are available, but I read that they do not support old chipsets like the 200M. I would like to know some pointers or instructions on how to get acceleration working. Most of the information I read seems to be outdated.
tommy@tardis:~$ glxgears -info
Warning, xpress200 detected.
GL_RENDERER = Mesa DRI R300 20060815 x86/MMX+/3DNow!+/SSE2 NO-TCL
GL_VERSION = 1.3 Mesa 7.0.4
[code]....
opensuse v11.2, linux 2.6.31.12-0.1-desktop x86_64
ati radeon hd3200 (built into motherboard)
gnome desktop
The video acceleration is clearly not enabled since I can practically watch each pixel drawn. (Well, a bit hyperbolic, but really slow.) Another system, same hardware, had this slow video problem and at one point required a complete OS re-installation. The slow video refresh went away. So there is some way to configure the graphics+display to enable acceleration at install time.
All of the videos on tennistv are flash. The pre-recorded videos seem to play okay using iceweasel and flashplugin-nonfree but the CPU is very high. When she watches live streamed matches the video stalls and jumps, so I have been trying to figure out why. Tennistv support people say that Linux isn't supported and that streaming is "harder" but don't explain why. They suggested using Google chrome, which did seem to work as well as iceweasel but no better. In desparation I tried XP and it was much better and uses much less CPU.
The only difference I could think of was that flash video hardware acceleration works by default in XP, so I started reading up on Flash video acceleration for linux. The latest Adobe flash player releases appear to support video acceleration, but it's switched off by default. So I upgraded to the latest version and did and then restarted iceweasal if you right click on a flash video you can set hardware acceleration in a tick box, but that seems to be there whether the above is config file is there or not there isn't a live tennis match on again until June 6th. How can I tell if hardware acceleration is actually working or not? The PC is has a 3GHz CPU and 1G RAM. Seems nuts that it can't play video properly. Its a Dell SX280.
Today I installed the latest Ubuntu, added VLC and... the acceleration is not there. When I compiled VLC myself on 9.04 I had a checkbox to enable hardware acceleration in the FFMPEG codec settings but this checkbox is not present in the VLC that was downloaded to my 10.04 by default.am I doing something wrong or is the hardware acceleration simply not there? And what do I have to do to enable it? Is FFmpeg in 10.04 compiled with VAAPI support? Is VLC in 10.04 compiled with VAAPI support? Do I need to recompile both or just on of them? I have just updated my system and now I'm not able to watch the family movies from my HD camcorder.
View 2 Replies View RelatedI was looking at purchasing a radeon x1300 for a multimedia pc for my lounge and was wondering if anyone knew whether hardware video acceleration with this card was supported with ubuntu? I read that on the ati website that it does support mpeg2,4, etc video acceleration,but didn't know if this was so for ubuntu. I have a few bluray quality movies that I would be interested in playing, so hardware video acceleration is a must.
View 1 Replies View RelatedI'm currently running a three-monitor setup, two of the monitors being connected to an NVIDIA card, and the third being connected to the motherboard's onboard ATI adapter. This works, and it actually works quite well, but after installing the nvidia-current drivers (using the GNOME dialog), I am unable to get any video acceleration going. The GLX module doesn't seem to want to load, and while I'm actually quite impressed with the video performance I'm getting with the open-source drivers, I'd really like to have the OpenGL capability, as it does make things look prettier.
Relevant configs and logs are below.
I should clarify - I don't care about the 3rd monitor on the ATI adapter; I'm only concerned with getting OpenGL working on the two on the NVIDIA - if that's possible, which it may not be...
System:
Code:
xorg.conf:
Code:
I thought this may be of interest, so I'm sharing. I've built some experimental mplayer packages for Fedora 11 and Rawhide (x86-32 and x86-64 arches) with shiny new features. Aside from being very recent snapshots, one of them includes support for hardware video playback acceleration via VDPAU and VAAPI, and the other includes support for multi-threaded playback (so you can split the decoding load across multiple cores).
The playback acceleration can definitely be used on NVIDIA adapters (from the GeForce 8xxx series onwards) using the proprietary driver (not, unfortunately, nouveau). Also on Intel Poulsbo (GMA 500) adapters, using my packaged version of the native driver for that chipset (link is in the blog post). VDPAU acceleration is also allegedly possible on S3 Chrome 530 GT and S3 Chrome 540 GTX adapters using S3�s own driver, but I haven't had the chance to test that. Multi-threaded playback can be done on any system, but only really makes sense on those with multiple processors (cores).
Full details of where, how and why are in my blog post:[URL]..
there is a way to use hardware acceleration with a Nividia Gforce G 105M video card in Ubuntu.
View 5 Replies View RelatedI am in the process of building a new desktop machine for work and fun. I am looking to run a undecided flavor of Linux (guessing Ubuntu) as my primary OS and several Windows installs with a Windows 7 install for .net development and gaming as virtualized environments.
From my previous experiences with virtualization software in Linux I was never able to find an application that offered descent video card support / graphic acceleration etc. to be capable of playing any games within one of the virtualized environments. And since I will be investing quite a bit of money into this system for gaming I would naturally want to find the best option available to achieve this setup.
So Onto my question: Is there any virtualization software available for Linux that has full video card support, graphic acceleration and capable of taking advantage of everything the video cards have to offer within the virtualized environments?
Or am I stuck with running Windows 7 as my primary OS and using virtualization for Linux and the other OS's?
Also I have no preference on open/closed source and price range would be up to $175.00 to support at least 3 virtualized environments.
While installing XBMC, which was working with my standard Ubuntu install, I accidentally installed NVidia hardware acceleration (sudo apt-get install libvdpau1 nvidia-185-libvdpau) on a notebook with ATI video.
Now XBMC does not work and says it requires OpenGL. apt-get remove does not work for that package because it's transitional. how I can get my stuff working like it was?
About 1 hour after successfully installing 9.10, the window elements started flickering and were inaccessible. I was working on intalling dimdim, but I did not touch any system files around the time the failure occurred. Thereafter, any regular login attempt results in a flickering black box on top of the new dim-gray-light ubuntu login window. The machine needs to be rebooted to get out of this mode. System restore mode works perfectly. startx starts the x environment, but with the flickering and uselnessness. The machine is a dual bood Ubuntu/Vista box (yeah, I know, Vista came with it). It is an intel quad core 2.33 MHz processor. The video is a cheapo on-board type. I have included system stats at the end of this message.
System Information report written at: 01/24/10 14:51:33
System Name: MERCURY
[Components]
[Multimedia]
[code]....
everex gPC2 tc2512 they went under
ubuntu 804 hardy
no windows
single boot
my onboard video is going bad.i have a radeon 9250 pci 256mb v/d/vo card.i would like to install before the onboard goes all the way out.how and what all do i need to do.what do i look for and change in the bios.yes it may be the power pack but if not i can not install the video card later
i have this problem i install android sdk, and i install libreries: libstdc++5, lib32stdc++6, lib32ncurses5 and libstdl1.2-dev,
now if i use ldd comand don't have problem, but when i use eclipse and i compile a simple example (hello word example), i have this
error: [Emulator] SDL init failure, reason is: No available video device i have a notebook toshiba satellite A300-1RI whit ATI Radeon 3650, i install the amd driver and all work well.
I have a computer with three video cards and six monitors. Works great on Windows. Trying to get it to run Ubuntu 10.4 as well. It loads fine when I have it configured to run on one adapter; detects both screens, runs ok. But I want to turn the other 4 monitors on and run the whole thing as one extended desktop (one session, etc). So I downloaded and installed the newest ATI driver for Linux, which seems to work, kinda. I ran this to set up the screens:
aticonfig --adapter=all --initial -f Now when I boot, Ubuntu seems to turn on all the screens (3 viewports, each with two cloned displays from what I can tell). When I enter my login info OR move the mouse off the main screen, the screens freeze and the kbd/ms become unresponsive.
[Code]...
I'm trying to create a VPN through SSH but encounter the following:
Code:
[18:42:11]root@bronzhip:/home/casey# sudo ssh -w 0:0 97.**.***.221 -i VPN
channel 0: open failed: administratively prohibited: open failed
[code]....
I just got an error message and i have no clue what it means.Error: Unable to establish connection with FAM.Do you have "FAM" or "Gamin" installed and running?I installed the net cd of Lenny and it is up to date so I don't know whats up.
View 2 Replies View RelatedI have a headless server, running Fedora 13. I want to make a ssh tunnel to that server from laptop that is also running Fedora 13. Logging into that server over ssh works well, X11 forwarding also works, but I can't establish a ssh tunnel.
At the moment I was trying to connect two small python tcp sample programs, that communicate through port 8000. Running them both on my laptop works well.
What I am trying to do is that I am making two seperate ssh connections to my server, let's say it's address is myserver.com.
1) I make a 'standard' ssh connection to it
Code:
And run the server program
2) I open another terminal window and make the tunnel
Code:
3) I open 3rd terminal window and try to run the client program, that is trying to connect to localhost:8000.
If I understand it correctly, the client should now connect to localhost:8000, ssh would discover that and send that data to myserver.com port 8000. Then the server program on myserver.com is listening on that port and should get that data and send "hello world" string back to the client. Then the client should get that, print it to stdout and exit.
Unfortunatly all what it does is that it just hangs for about ten seconds and then says "connection lost" (timeout?)
I have tried other programs, they also timout.
By passing the -v argument to ssh it outputs:
Code:
When I try to connect the client it prints four more lines:
Code:
So as you see, it says that the connection times out..Also can anybody tell what the "Unspecified GSS failure." means? The possible break in attempt is caused by connecting to the server using the myserver.com address while being in the same local network with the server. If I connect using server's local ip address (ie. 192.168.1.xxx), the message dissappears.
What I have:
Computer: Dell XPS M1210
Modem: SpeedStream 51000 - It's SBCGlobal
I followed the pppoeconf setup instructions.
cracker@Jack:~$ sudo pppoeconf Plugin rp-pppoe.so loaded.
RP-PPPoE plugin version 3.8p compiled against pppd 2.4.5
I then asked it to start the connection.
cracker@Jack:~$ sudo pon dsl-provider
Plugin rp-pppoe.so loaded.
RP-PPPoE plugin version 3.8p compiled against pppd 2.4.5
Checked connection information and got this.
cracker@Jack:~$ ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:18:8b:dd:6e:cb
inet6 addr: fe80::218:8bff:fedd:6ecb/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
I have set WAN to 'bridged' mode for my D-Link DSL-G604T so that individual devices can connect directly to the internet.
A problem I now face is not being able to connect a computer running Ubuntu 10.04 LTS to the internet via DSL.
The computer connects to the D-Link DSL-G604T router via wireless network connection - which is established, but I am unable to connect to DSL and I don't know why. The DSL connection doesn't even list under the network icon at the top right.
I have two firewalls, one primary (fw1) and one fall-back/backup (fw2). On the LAN side the fw's reside in the same LAN segment. I have a client who wants VPN redundancy. So I configured two VPN tunnels for this client. One via fw1 and a backup via fw2. Since the default gateway on the VPN server points to fw1 only the tunnel via fw1 is established. OpenVPN can't establish a tunnel via fw2 because of the gateway and just sits there waiting...
View 1 Replies View RelatedI recently upgraded my flavor (Arch, latest version) and now I am unable to connect to samba (latest version; obtained through pacman) either through Windows or Linux. My error logs reveal: (/var/log/samba/log.smbd)
[code]....
nmblookup shows what it should but smbclient -L gives the generic "Error NT_STATUS_UNSUCCESSFUL". I also tried to reinstall Samba. I am not sure why it continues to try for CUPS, as I do not have printers listed in smb.conf.
I try to establish Firebird 1.5.4.4910 on CentOS 5.2. It is established without mistakes. But be connected to a server I can not. The command - xinetd-d deduces:
Service configuration: gds_db
id = gds_db
flags = REUSE IPv4
socket_type = stream
[code]...
At attempt to be connected to a server in magazine there is a message:
May 27 10:20:48 Mikle xinetd[4737]: START: gds_db pid=5399 from=192.168.1.206
May 27 10:20:48 Mikle xinetd[4737]: EXIT: gds_db status=0 pid=5399 duration=0(sec)
May 27 10:20:48 Mikle xinetd[4737]: START: gds_db pid=5404 from=192.168.1.206
May 27 10:20:48 Mikle xinetd[4737]: EXIT: gds_db status=0 pid=5404 duration=0(sec)
I just set up vsftpd, from the localhost it works just fine, but when i try to acess it from the network, via firefox or the osx "connect to server" i get a message can't establish connection.
I 'm a new to setting up servers, so maybe i just havent set any neccessary paramters for anonymous login.
My vsftpd.conf looks like this:
Code:
I'm trying to establish NFS mounts for my SOHO NAS 500 as I used to with other versions of OpenSuse. I go to Yast, I find my SOHO server and my exported directory. I put rw for options and Add it to the list. When I exit I get the following from Yast in a pop up: YaST got signal 11 at YCP file Service.ycp:77/sbin/yast2: line 399: 13095 Segmentation fault $ybindir/y2base $module "$@" "$SELECTED_GUI" $Y2_GEOMETRY $Y2UI_ARGS I am not an expert (rather basic knowledge) but this is really cryptic for me. Anyone knows what it is? Of course my mount doesn't work. My newly established system is working fine with 11.3 OpenSuse.
View 1 Replies View RelatedWorking in CentOS. Want to have drag-and-drop SCP access to another system.
Opened up the file manager (nautilus) and went under File -> "Connect to Server". Filed in the information, hit connect. The connection will sit forever and will never properly establish. It creates an icon on my desktop, but noting else.
If I go into terminal, su to root, open nautilus and then repeat the process as a root user, then it works successfully. Connection established after I trust the remote host. File transfer works fine.
what is occurring when I attempt to connect as my normal user?