Slackware :: Windows 7 Slow After Install ?
Apr 6, 2011I set up a dual boot with windows 7 and slackware, but now my Windows 7 is so slow that it wont even open things.
View 14 Replies
ADVERTISEMENT
Networking :: New Slackware 13 Install - Slow Internet?
Jan 24, 2010After installing Slackware 13 and configuring it as a router, I'm getting very slow internet speeds on my clients. It takes forever to connect to a website or downloading 100mb bin file also takes forever. On the Slackware box the speed is fine though. When I boot from my previous Slackware 12 drive, the speed on the clients is ok again.
I have compared config files from my old and new installation and haven't found a difference. from other posts I learnt that disabling IPv6 by adding it to the blacklist could help. But this didn't help me either. I have also compared a traceroute on both installations. This also doesn't show a (big) difference.
The only difference I have found is that in my Slackware 13 setup the following modules are loaded while with my old Slackware 12 lsmod is empty.
Code:
The only thing I can think of is a missing option in the kernel. I have used the huge-smp from the Slackware DVD, assuming this would have all the important stuff enabled by default. It this right?
Some additional info:
eth0: nVidia Corporation MCP51 Gb onboard Gb NIC, connected to LAN (static)
eth1: 3COM 3C2000 Gb NIC, connected to cable modem (dhcp)
dhcpd is running to configure clients in the network
arno-firewall installed
Files I have compared with my old (working) system:
Slackware :: Enable Windows Wireless Drivers In Slackware 13.1 And How To Install XFCE
Aug 22, 2010I recently installed Slackware Linux 13.1 , and my Wireless is down. I've only installed 3 Linux disto's on my main laptop (Ubuntu 9.10 , 10.04 , and Crunchbang Linux 9.04 , just had Crunchbang), and they all had the same problem. In all three , I was able to enable Windows Wireless drivers and every thing worked. Now , I'm assuming I have to the same ting in Slackware? Sorry , but I have no idea what my wireless card is. But I know that my laptop is a Dell Insprion E1705. One last thing , I did ifconfig and that wlan0 is my Wi-Fi interface. I typed ifconfig wlan0 up to see if that was the problem. After I did that , I got and error message. Then I typed ifconfig wlan0 down to see if it was down and it made wlan0 down. I tried bringing it up again , but I got an error saying it couldn't find the device specified. Also , how do I install XFCE? I really don't like KDE for some reason and would like to install XFCE. I chose XFCE over GNOME (my favorite) because I want to try something new.
View 4 Replies View RelatedSlackware :: Windows Raid-O Install Virtualbox, Will Slackware Install Raid-o Without Raid Driver?
Feb 28, 2011If I have a windows installed in raid-0, then install virtualbox and install all my linux os,s to virtualbox will they be a raid-0 install without needing to install raid drivers?
View 1 Replies View RelatedSlackware :: Install To Dual-boot With Windows XP?
Jun 20, 2010I haven't used Slackware before but I used Ubuntu which I dual-booted with Windows XP.
Now I want to dual-boot Windows XP with Slackware. How do I install Slackware on top of my Windows?
My laptop is a ThinkPad my Windows is XP Pro SP3.
Slackware :: Install On MS Hyper-V (Windows 2008 R2)?
Apr 15, 2011I tried to install Slackware on MS Hyper-V (Windows 2008 R2)?
View 2 Replies View RelatedSlackware :: Install Windows Server 3008 Along Side?
Jan 2, 2011I want to install either windows xp or windows server 2003 or 2008. Now i want to make it so when i boot i get the bootloader window asking for windows or linux. How do i install my windows so when i click enter on windows it boots windows?
View 4 Replies View RelatedSlackware :: Install Windows And Now Cannot Enter In Slack ( No Start Screen With Options OS )
Nov 8, 2010I have Windows 7 and Slackware on my laptop, but I reinstall Windows 7 and now I cannot enter at Slackware ( I don't have anymore start screen to choose OS). Do I need to install again Slackware or just lilo and how to do that?
View 12 Replies View RelatedSlackware :: 13.1 - Xpdf Very Slow And Cpu Goes To 100%
Nov 14, 2010I'm gonna tell you about slackware installation on my notebook, an acer travelmate 800lci.
On this notebook, I successfully installed (and work with) slackware from version 10.0 till the recent 13.0. Upgrading to a new version till using a new internal hard disk (from 40 GB to 160 GB). After upgrade I fully reinstall slackware 12.2 and then upgrade to 13.0.
Now, I had to use the notebook for testing, so I made a new full installation of slackware 13.0 and after some time a new full installation of slackware 13.1.
On this disk (160 GB P-ATA) I have to pass the following parameter to the kernel:
during installation and boot.
This operation solve the issue that can "see" the full size of the disk (160 GB) and not the 137 GB limit.
Only using slackware 13.1, occur a big (for me) problem.
I can fully reproduce it opening any pdf document with xpdf: moving into document with arrow keys make the cpu goes to 100% and page "fault/s" goes from 30 to 8000 and some times 15000 "fault/s". So, xpdf becomes unusable. This problem reflects in similar manner to other software, like firefox.
Here is my question: what type of analisys could I try to solve/analyze this issue? Maybe the kernel, xorg?
On slackware 13.0 all works perfectly.
Slackware :: Slow DSN Lookup With 64
Sep 7, 2010I've been comparing the current Slackware 32 bit versus 64 bit, and I've noticed that the 64 bit version is as slow as dialup for domain name lookup.
The 32 bit version is very fast to find websites after a mouse click, whereas the 64 bit version takes forever looking up URLs. (using Firefox)
All the other 64 bit Linuxes seem to be the same way, not just Slackware.
The /etc/resolve.conf file is the same for 32 or 64 bit Slackware, but something is not right. The 32 bit version has a /etc/dhcpc directory, but not the 64 bit version.
Could this be causing the extreme slowdown?
It's really very irritating when the rest of the system is blazing fast.
AMD Phenom II X4 955
Asus M4A88TD-V
8 GB Corsair XM33 ram
Slackware :: Opengl Is Terribly Slow?
Apr 8, 2010Just installed slackware-13, and sorting issues. I actually have googleearth running - just.It's telling me it's using opengl, but opengl is absolutely cat on this box I have ATI RS690M with the radeonhd driver on my laptop. Opengl is terribly slow. Videos stall, but I move them withmplayer -vo sdl <my_video>/end backgroundAnything I can do with Google earth?o option to swap. fglrx is crap on opengl.
View 7 Replies View RelatedSlackware :: New 13 X64 Installation - Slow DNS Lookup ?
Mar 31, 2010I've been cracking on with getting a new Slackware 13 x64 installation going. I've got a problem with browsing the net which I can't put my finger on.
When I try to access a site my machine spends a long time with the "Looking up www.website.com" message at the bottom. It can take 7-12 seconds before the site is found. Normally I would blame this on my ISP or connection but Mint, Debian and Windows XP aren't having this problem, they just zip straight to the site whether I've been to it before or not.
Is anybody aware of where the problem might be? It's not in the browser either because Opera, Seamonkey and Firefox all have the same problem issue.
Slackware :: PSX Emulator Extremely Slow On 12.2
Aug 3, 2010I downloaded the emulator called pSX so i can play my playstation cds in my computer. on my laptop i have slackware 12.2 installed.
The dependencies for the emulator are:
opengl
gtk
alsa
gtkglext
libxml
I found the appropriate packages for all of these (with the exception of opengl, I assume that means it's preinstalled, correct me if I'm wrong) and installed them. the emulator runs, at about a quarter the speed it's supposed to. I get no error messages in the terminal, just the huge speed drop. has anybody else gotten this emulator to work fine in slackware?
Slackware :: Intel Driver Isn't Being Used And KDE Slow?
Mar 4, 2010I upgraded to -current last night hoping to improve my Intel 845G graphics controllers functioning in X, I've had to use the vesa driver for stability. The upgrade was completed but KDE seems as slow as ever. Here's some snippets from Xorg.0.log:
X.Org X Server 1.7.5
Release Date: 2010-02-16
X Protocol Version 11, Revision 0
Build Operating System: Slackware 13.1 Slackware Linux Project
Current Operating System: Linux speedy 2.6.33-smp #2 SMP Sat Feb 27 20:12:16 CST 2010 i686
code....
It seems I'm still using the vesa driver, any ideas on why the intel isn't being used and how to fix it?
Slackware :: Slow Startup (/etc/rc.d/rc.M) With Wireless?
Jan 19, 2010My Slack takes some time to boot. It hangs about 5 secs in a line that reads:
Quote:
/etc/rc.d/rc.M: eth1 information: "MySSID" Then, it polls for a DHCP server on eth1 (I didn't write down the exact message). I noticed that if my router is off, the polling process take quite some time to move on.. I tried to look the rc.M, rc.inet1 and rc.wireless scripts, but I couldn't pin point what to change... I tought of adding an '&' at the end of the command that issues the line I quoted and on the DHCP. The DHCP line I didn't search much, I'll try it later...
Networking :: Internet Is Very Slow With Slackware 13 Router
May 16, 2011I just installed and configured Slackware on an old computer I am using as a router.
The internet works fine on the slackware box (router) but all of the computers behind it are having issues. When browsing, some websites work perfectly fine, while others are slow to load, and a few don't load at all. I'm not really sure where to start on diagnosing this, so any help would be appreciated.
Also whenever I restart the computer, I have to use this command before the DHCP server will start. What do I have to do to get it to start up with the computer?
Code:
Slackware :: Opera 10.60 Very Slow To Start New Links
Jul 8, 2010I've been using Opera 10.11 on two different computer systems, two different locations (work & home), and two different Slackware versions (13 & 13.1 current). Opera 10.11 runs very quickly on both. After upgrading to Opera 10.60, I now find that linking to new web pages takes 5 to 10 seconds, but returning to a previous page is almost instantaneous.
I've tried installing 10.60 using slackbuilds and Opera's installer - both give the same results. I've since reverted to Opera 10.11. why it is so slow to open web pages? Opera 10.60 for Win7 works great, so what happened to the Linux version?
Slackware :: Slapt-get Slow When Downloading / High It?
Nov 30, 2010I am a newbie regarding the Slackware, though i have some millage on Ubuntu. Anyway, i have Slackware 13.1 and slapt-get is really, really slow when downloading packages, even when i do slapt-get -update the slowness is just killing me
The second question is somewhat different. How can i view dependencies on which a particular application is depended?
Slackware :: Slow Dns Resolution With A Netcomm Router?
Jul 26, 2010i have a nb5plus4w modem/router at home which acts as a dhcp server on my lan. upon connection it instructs the clients to use 192.168.1.1 as a dns server (which is the ip address of the router) and linux machines are happy to use that in /etc/resolv.conf. now the issue is that under these conditions dns resolution is sloooow. there have been some discussions on the net saying that the router is not a 'real' dns server (don't know what that means), but the only way i have been able to get around the issue is to edit /etc/resolv.conf to use my isp's dns servers and then chattr -i the file so that dhcpcd doesn't change it.
this approach works for the desktop and even though it is ugly it's effective. the laptop is a different issue. if i take it out of the house i have to chattr -i and let the new network put it's dns addresses in and then change it all back when i get home so, the question is... can i do something to stop doing chattr and get the dns performance of a windows machine (dns resolution is quick on the windows machines)?
Slackware :: Slow - Every 30 Seconds The Internet Lags
Oct 20, 2010It seems every 30 seconds the internet lags, after that it is fine for 30 seconds. And this happens continuously. Also it seems when I am on Firefox if I am connected to a website, I can navigate the website with not further trouble. But if I navigate away and try to go back, it takes a while. I didn't update, or upgrade or anything. I am running 13.1 and have been since it came out. This just started with the internet 2 days ago. Also I have a dual boot with Win7 and the internet is fine on Win7.
View 8 Replies View RelatedSlackware :: Wireless Keyboard In KDE Slow To Work
Nov 1, 2010I have a Slackware 13.1 install on a Desktop PC with wireless keyboard and mouse. When I log in it takes a very long time(5 minutes or so) before the keyboard starts working, and f.ex. it's possible to do Alt-F2. The mouse also works slowly in this period, but it is working.
I'm running KDE 4.5.2 on Slackware current, but did have the same problems with the fresh install and KDE4.5.1. When the lag period is over everything is working as normal. I have turned of strigi indexing and could not find anything special when running "ps ax" or "top".
Slackware :: Xcompmgr Working Slow At Start
Mar 5, 2011i got 2xgtx280 and 2 x xeon 5650 transparency and shadows work ok but i have little problem when windows mannager starts(fluxbox) when i click first on for exemple firefox windows its moving slow for 4 sec after that is ok and if i dont use that window for 2 min and i wanna use it again its slow again for couple seconds how can avoid this? i was trying alot xorg.cnf settings and xcompmgr and nothing changes...
View 1 Replies View RelatedSlackware :: Ati Radeon Drivers - Everything Freezes Or It's Just Dead Slow
Nov 5, 2010My Nvidia card broke down recently, I replaced it with Ati Radeon 2600HD Pro.
Now I have no compositing, everything freezes or it's just dead slow.
As for now I'm using fglrx drivers, but I've tried xorg drivers before, without success either.
My xorg.conf
Code:
Slackware :: Intel 82865g Current Glxgears Slow?
Nov 22, 2010When i checked last time couple months back glx gears gave me 1400 frames around now i get
Code:
glxgears
Running synchronized to the vertical refresh. The framerate should be approximately the same as the monitor refresh rate.
21 frames in 6.6 seconds = 3.160 FPS
2 frames in 5.6 seconds = 0.359 FPS
84 frames in 5.8 seconds = 14.362 FPS
149 frames in 5.0 seconds = 29.724 FPS
300 frames in 5.0 seconds = 59.814 FPS
and everything is running slow im wondering where the problem might be?
code....
Slackware :: Nepomuk Slow Down Machine And Used 1Gb Of Disk Space
Jan 14, 2010Quote:
Originally Posted by mcnalu
Nepomuk/strigi slowed my machine to a crawl and used 1Gb of disk space so I turned it off. In my machine is the same thing. Turning it off is a right and wise solution?
Slackware :: Slow Graphics With 13.37 And Radeon Mobility X1600
May 4, 2011I've upgraded (reinstalled) from Slackware 13.1 to 13.37 on an old iMac and have problems with slow graphics.
lspci says this about the graphics card:
Code:
With Slackware 13.1 I had no KMS enabled and graphics speed was okay. It wasn't very good, but okay for everyday work. Now with 13.37 it's extremely slow. glxgears runs with only around 38 fps, no matter what I do. And every now and then when logging off, I get a black screen and no new kdm-login. But I can ssh into that machine and restart X by issuing 'init 3;init 4'.
KMS is enabled (I've also tried disabling it, but then KDE crashes right after logging in) and it's a fresh installation of 13.37 with a 2.6.37.6 kernel.
What can I do?
I have to admin I don't know this video and X stuff very well and I used to have machines with NVIDIA cards.
If there's anything else than the usual Xorg.0.log needed.
To me the log doesn't look like there's any problem whatsoever:
Code:
Slackware :: Slow Terminal History Browse Using Vesafb ?
Jul 10, 2010I've just installed Slackware 13.1 and am using a VESA framebuffer on a dv5-1251nr HP laptop with standard hardware.
In bash when I browse the command history using the up/down arrow keys the input line changes rather slowly.
For example, when I am on the history command
Code:
And the next command I go to is
Code:
The terminal input line deletes each character from the beginning and changes something like this:
Code:
But going the opposite direction, from
Code:
To
Code:
Is instant.
The effect does not happen with VESA turned off. I've used VESA on other computers without this problem.
Slackware :: Dual Boot Of Slackware 13.1 And Windows Server 2008?
Oct 27, 2010I installed Slackware 13.1 and Windows server 2008, I also installed LILO in MBR, I Found I can boot into slackware, but can't boot into Server 2008. then I　use command bootsect/fixmbr. now I can boot into server 2008, but the problem is I can't boot into slackware. I try to install lilo to supper sector. it's not works. I only can boot my slackware by a USB stick.who can help me to solve this problem? I really need these two systems.
View 5 Replies View RelatedSlackware :: Which Is Best Free Virtual Machine To Run Windows On Slackware?
Feb 9, 2010I know that there are lots of solutions, like Sun virtualbox, vmware, ecc ecc.What's the best choice? I'm searching the best compromise between license, stability, features, speed.
View 14 Replies View RelatedSlackware :: Windows 7/Slackware Dual Boot, Different Discs?
Sep 19, 2010My new job requires I use Windows and as such I put a second HDD in my laptop for the purposes of Window/Work The issue is that Windows will not install on this second disc (Windows cannot create partition or install to disc). I got around this by installing Windows to the first disc, then the second then putting Slackware back on the first but then I suffer the "Bootmgr cannot be found, press ctrl + alt + delete to restart".
I am using Lilo and I have never really had an issue dual booting them on the same disc (Admittedly over a year ago) but it is of the utmost important I have them on separate Discs. Has anyone encountered this and/or know a way around?