Red Hat / Fedora :: Configure A Set Of Hard Drives As A RAID Configuration?
Apr 21, 2010
I am currently trying to configure a set of hard drives as a RAID configuration. My system is running with Red Hat Enterprise Linux Client release 5.1 as the base OS. I am booting from CD. I am trying to image a set of drives that have not been imaged before. When the GUI dialog window for disk setup is displayed, it shows a default disk layout including a LVM slice. In the disk layout is a /boot partition already. It is not what I would like so I edit it to be the size for my system and make it the primary partition. I also select it to be a software RAID. I then add three more partitions for my drive 'A' all of type software RAID and NOT primary partitions.
At this point my drives have the correct number of partitions except for showing the LVM slice. I select 'RAID' again, followed by selecting 'Clone a drive to create a RAID device ...' followed by 'OK'. I then get a dialog to select the source and target. i select my drive 'A' to be the source and 'B' to be the target followed by 'OK'. An error dialog is received stating that all the partitions are not of type software RAID. The disk partitions are all type software RAID except the extended LVM slice. I can not get past this point and I am following a procedure written some time ago by a person that is not available.
View 2 Replies
ADVERTISEMENT
Jan 7, 2011
I have three 640GB sata hard drives that I would like to put into a raid 5 configuration. I would like to opt for a software raid 5 so its hardware independent. I was trying to follow these instructions, but they seem a bit dated.
View 2 Replies
View Related
Apr 15, 2009
I have been battering with FC10 and software RAID for a while now, and hopefully I will have a full working system soon. Basically, I tried using the F10 live CD to setup Software RAID 1 between 1 hard drives for redundancy (I know its not hardware raid but budget is tight) with the following table;
[Code]....
I set these up by using the RAID button on the partition section of the install except swap, which I set-up using the New partition button, created 1 swap partition on each hard drive that didn't take part in RAID. Almost every time I tried to do this install, it halted due to an error with one of the raid partitions and exited the installer. I actually managed it once, in about...ooo 10-15 times of trying but I broke it. After getting very frustrated I decided to build it using just 3 partitions
[Code]....
I left the rest un-touched. This worked fine after completing the install and setting up grub, reboot in to the install. I then installed gparted and cut the drive up further to finish my table on both hard drives. I then used mdadm --create...etc to create my RAID partitions. So I now have
[Code]....
View 2 Replies
View Related
Sep 19, 2010
I just went out and bought stuff to build a new computer, and among the parts was a Gigabyte ga-890fxa-ud5 motherboard ([URL]). The board has 3 (well, 4, but we'll stick to the 3) main sata interfaces, with 2 slots per interface, allowing 6 sata drives. In slot_0 i put my blu-ray drive, in slot_1 i put my drive that will host the OS and its partitions, and that is in the sata connector pair on the left. The middle sata connector pair (slot_2 and slot_3) i have 2 2tb drives, and in the sata connector pair on the right (slot_4 and slot_5) i have 2 1.5tb drives.
[Code]....
View 14 Replies
View Related
Aug 26, 2009
I currently have a clean installation of Windows on the Primary drive (13gbs) and I want to install Fedora 11 on the other (7gbs). Should I install grub on the Windows hard drive or will Windows hate on me for that? Earlier I tried installing grub on the slave with the Fedora system, but I had trouble configuring Grub in a way that it would understand and I ended up messing up the MBRs of both hard drives.
View 1 Replies
View Related
Mar 17, 2010
I want to make a RAID5 array with 4 2TB hard drives. One of the drives is full of data so I will need to start with a 3 disks and then once I copy the data from the 4th onto the array, I will then add the 4th drive. This will be my first experience with RAID. I've spent a few hours searching for info but most of what I have found is a bit over my head.
View 9 Replies
View Related
Oct 30, 2010
I'm using 4 hard drives (1 of which is a sata drive) and i need help installing raid drivers i cant get these hard drives to mount at all
View 3 Replies
View Related
Feb 23, 2010
I'm renting a dedicated server with a company that claims that the server has 2 hard drives in a software RAID 1 array, but I need to make sure that the server really has the 2 HDD, and the size of the 2nd drive... how to do that ?? system is Centos 5.3
View 1 Replies
View Related
Oct 30, 2010
I have the newest Ubuntu installed on my machine. It currently has a 160GB sata drive. I just bought two shiny new 2TB drives that I want to RAID as 4TB. How do I go about adding these two hard drives even though install is complete? I want the 4TB assigned to my /home directory.
View 4 Replies
View Related
Aug 3, 2011
I have a PC104 running debian. I have 3 hard drives (in addition to the one booting) mounted in fstab by UUID. I use the options defaults,error=remount-ro. However, this means that when I boot with the hard drives not attached, I have to press Ctrl-D to bypass when the boot discovers the drives are missing. Is there a timeout commandoption I can add to fstab so that it automatically continues booting even if the hard drives are not attached? I could not find anything on a timeout command. (I tried adding timeout=1000 but no-random guess)
View 5 Replies
View Related
Apr 22, 2010
I know my Linux Servers have RAID but I want to know
1. Can I find RAID level?
2. how to find Disk information...I mean if it's not possible to get RAID Can I get how many hard drives and the real size?
View 2 Replies
View Related
Jan 29, 2010
So windows wouldn't recognize my drives as a raid setup, so I disabled it and switched to IDE, now Ubuntu 9.10 installation will only recognize my drives as RAID. I have and ASUS M3A32-MVP Deluxe Series motherboard, it has 4 sata connectors and 2 marvel controlled sata connectors. In the 4 sata connectors I have my 2 wd 500gb hds, my dvd burner, and my external usb, esata slots. In the marvel controlled sata connector I have a wd 160gb hd. Originally when I built the computer I wanted a raid setup with the 2 500 gb hds.
But windows wouldn't recognize the raid set-up and wouldn't boot properly. So I said screw it and removed the raid and set all the drives to IDE. Then, when I tried to install Ubuntu 9.04 it would only recognize my 2 500 gb hds as raid. Gparted recognizes the drives as both raid and IDE. Eventually, after a day or two of praying and messing around the installer recognized both drives as raid and IDE. A couple months later here I am trying to install Ultimate Edition 1.4.
View 14 Replies
View Related
Apr 8, 2010
i have cretaed RAID on one of my server RAID health is ok but its shows warning. so what could be the problem. WARNING: 0:0:RAID-1:2 drives:153GB:Optimal Drives:2 (11528 Errors)
View 1 Replies
View Related
Jul 5, 2011
I have Fedora 14 installed on my main internal drive. I have one Fedora 14 and one Fedora 15 installed on two separate USB drives.When I boot into any of these drives, I can't access any of the other hard drives from the other drivesll I can, but just the boot partitions.Is there any way of mounting the other partitions so I can access the information?---------- Post added at 12:42 PM ---------- Previous post was at 09:34 AM ----------I guess even an explanation on why I can't view them would be good too.
View 7 Replies
View Related
Apr 4, 2010
I'm about to install Ubuntu on two 250-gigabyte hard drives in a RAID 1 array, but I'm confused about how to partition my hard drives. How much space should I give to each partition? How many partitions should I create and where should I mount them? (I should mention that Ubuntu will be the only OS on this array.)
View 3 Replies
View Related
Jan 18, 2010
I'm breaking into the OS drive side with RAID-1 now. I have my server set up with a pair of 80 GB drives, mirrored (RAID-1) and have been testing the fail-over and rebuild process. Works great physically failing out either drive. Great! My next quest is setting up a backup procedure for the OS drives, and I want to know how others are doing this.
Here's what I was thinking, and I'd love some feedback: Fail one of the disks out of the RAID-1, then image it to a file, saved on an external disk, using the dd command (if memory serves, it would be something like "sudo dd if=/dev/sda of=backupfilename.img") Then, re-add the failed disk back into the array. In the event I needed to roll back to one of those snapshots, I would just use the "dd" command to dump the image back on to an appropriate hard disk, boot to it, and rebuild the RAID-1 from that.
Does that sound like a good practice, or is there a better way? A couple notes: I do not have the luxury of a stack of extra disks, so I cannot just do the standard mirror breaks and keep the disks on-hand, and using something like a tape drive is also not an option.
View 4 Replies
View Related
Jun 9, 2011
so I setup a raid ten system and I was wondering what that difference between the active and spare drives is ? if I have 4 active drives then 2 the two stripes are then mirrored right?
root@wolfden:~# cat /proc/mdstat
Personalities : [raid0] [raid10]
md1 : active raid10 sda2[0] sdd2[3] sdc2[2] sdb2[1]
[code]....
View 2 Replies
View Related
Sep 1, 2011
I have a RAID 1 that is mounted and working. But for some reason I can also see the individual drives under gnome Devices on gnome-shell. Is there a way to hide them from gnome or linux in general. (So only the raid 1 can be seen)
View 2 Replies
View Related
Jan 6, 2010
I recently installed Fedora 12 for use with Amahi HDA. Before installing on the Hard drive I used the LIVE CD to test it out. While using the LIVE CD I could see all my HDD's. My file system, my 2nd Hard Drive, and my Raid 0 Configuration. (2 250GB drives) and could browse all my files on those drives.
After installing the full version on my hard drive, my RAID drives are showing up as seperate drives. I have a Asus P4P800 board using hte SATA raid. I know its FAKERaid and not a true hardware raid.
My goal is to restore the Raid in Fedora and make those drives active. However, i dont want to lose any of the data on those drives. To make sure I wasn't an idiot, i rebooted withthe LIVE CD again and verified that I could see the Raid Array.
View 3 Replies
View Related
Dec 31, 2010
My System Intel Core Duo E5300 Mobo - Gigabyte G31M-ES2L 1GB DDR2 800MHz RAM 4 x WD20EARS HDD I have been trying to install Fedora or Ubuntu for over a week. I thought it would take an hour and i would be away. I have been trying to install using the mdadm Software RAID feature. Everytime it takes about a day to format the drives and then i get an installation error. The drives state they are ready to use as is on any operating system other then WinXP, but this does not appear to be the case.
I am very new to Fedora... I have been doing some reading.[URL].. That information has been promising. I have been able to get into Fdisk off the live CD but i can't figure out how or if it is possible to do what i want it to.
Has anyone had any luck getting these drives to function correctly in a software RAID? I have had good luck with WD drives in the past and just assumed these drives would do what i wanted to but alas i have been proven wrong.
The partitions i wanted was...
- A 2GB swap parition
- A 10 GB RAID 1 partition for Fedora
- The remaining space as a Raid 5 for files.
Am i just banging my head against a wall here, or is this possible.
View 1 Replies
View Related
Jun 4, 2011
Fedora is having trouble identifying a raid partition, it sees them as separate drives. I got drivers from dell, but during a Fedora dvd install, it mentions nothing about a place to install extra drivers.
When it says it must "initialize" the drives, Fedora then breaks the dell bios raid. How to either install the dell drivers or make Fedora see the raid partition as one?
View 1 Replies
View Related
Mar 26, 2011
I am building a home server that will host a multitude of files; from mp3s to ebooks to FEA software and files. I don't know if RAID is the right thing for me. This server will have all the files that I have accumulated over the years and if the drive fails than I will be S.O.L. I have seen discussions where someone has RAID 1 setup but they don't have their drives internally (to the case), they bought 2 separate external hard drives with eSata to minimize an electrical failure to the drives. (I guess this is a good idea)I have also read about having one drive then using a second to rsync data every week. I planned on purchasing 2 enterprise hard drives of 500 MB to 1 GB but I don't have any experience with how I should handle my data
View 10 Replies
View Related
Aug 10, 2009
I have a fresh installation of Fedora 11 and I am having a hard time figuring out how to automount my storage drives. Each time I login, I try to access my various storage drives and gnome makes me authenticate asroot before mounting it. FSTAB lists only logical volumes but not my storage drives. What can I do to make sure these automount when I login?
View 3 Replies
View Related
Jan 12, 2010
I have two identical 73 GB Scsi ulta320 scsi drives, Fedora web server is install on one drive with all web files and etc. I wish to make an exact clone of the drive that will boot and run everything as the current drive does now. Is there a download of a program I could download or purchase that would boot and make an exact clone to do the above.
View 6 Replies
View Related
Apr 7, 2011
I am trying to figure out how to get the UUID for some of my external hard drives.the internet revealed a couple of promising leads, this is what I have tried so far:
ls -l /dev/disk/by-uuid -> didn't list the hard discs
blkid -> didn't list the hard discs
lsusb -v -> listed the hard disc but no uuid
A normally formatted usb key is listed with uuid. The external hard discs are fully encrypted by truecrypt(realcrypt). I have been reading not so great things about that itself, but for now I don't have a promising alternative that I can use with windows as well.Any google searches don't seem to cast any new light on this for me,I'd be open to suggestions if there's a better way to get a definite ID for a hard drive... I just need to be able to mount it with realcrypt
View 3 Replies
View Related
Jul 11, 2009
I installed Linux on my Y drive, and all went well until I tried to boot into XP again. I can't access or install an operating system to my other three hard drives, C, X, and Z.I think that during the install my hard drives were changed to something other then NTFS, but Linux won't access them either.
When I use my Windows XP or Windows 7 disc, it says the drive has 0mb free, and it can't install until I delete the partition, then reformat. I don't want to do this obviously, because I don't want to format all of my data.When I go to Places > My Computer it lists my CD drive, Filesystem, and the Y drive. It doesn't show my other three hard drives.Under Palimpsest Disk Utility I can see my other three drives, but I can't access the data on them yet.
View 3 Replies
View Related
Apr 10, 2010
I ran smartctl and it says "unrecognized" hard drive. I recognized the hard drive the first time I ran the test. But now, it's unrecognized? How come? I don't know how or why this happens. How can I get rid of this problem and the annoying icon?
I tried to run Windows, then started getting errors? This is strange: I've been running Linux the whole day. I last used the Windows hard drive was 2 days ago. Now its screwing up. Window is screwing up the hard drive? HDD has too many bad sectors. didn't touch it, I didn't do much on it, etc? I do not understand?!
View 4 Replies
View Related
Oct 5, 2009
I've installed Fedora 10 short time after it came out. Now I am having some problems unmounting thes drives on restart or shutdown. It hangs at the stage of 'unmounting file system'. I've looked into this matter and discovered that those drives are automatically mounted and shown on the Gnome file browser. As the /etc/fstab indicates, it is not mounted by it. I must have done something to have all the hard drives shown in the file browser and now Fedora seems to be unable to unmount them.
Quote:
#
# /etc/fstab
# Created by anaconda on Mon Sep 7 20:25:11 2009
#
# Accessible filesystems, by reference, are maintained under '/dev/disk'
[Code]....
View 4 Replies
View Related
Dec 11, 2009
First time linux user, am trying to install a fresh full install of Fedora 12 dvd i686 version. I have two identical sata drives, which fedora fails to identify. Have reset the bios, changed settings in the bios, still not finding them. I have an asus av8-x motherboard, with a athlon dual core processer.
View 5 Replies
View Related
Sep 3, 2010
The Fedora installer won't display my two SATA hard drives. I've tried both the x86_64 live CD and DVD. On the live CD, fdisk -l displayed nothing. However, if I click "Specialized Storage Devices" a devices shows up as "BIOS RAID set (stripe)" with a capacity equal to both my hard drives. I don't even have RAID enabled in BIOS - it is set to AHCI. Other os installers display the hard drive correctly.
Specs:
2x 640GB western digital caviar blacks
ASUS M4A78T-E 790GX motherboard
View 2 Replies
View Related
