General :: Ubuntu 9.10 Installation Insists For RAID Hard Drives
Jan 29, 2010
So windows wouldn't recognize my drives as a raid setup, so I disabled it and switched to IDE, now Ubuntu 9.10 installation will only recognize my drives as RAID. I have and ASUS M3A32-MVP Deluxe Series motherboard, it has 4 sata connectors and 2 marvel controlled sata connectors. In the 4 sata connectors I have my 2 wd 500gb hds, my dvd burner, and my external usb, esata slots. In the marvel controlled sata connector I have a wd 160gb hd. Originally when I built the computer I wanted a raid setup with the 2 500 gb hds.
But windows wouldn't recognize the raid set-up and wouldn't boot properly. So I said screw it and removed the raid and set all the drives to IDE. Then, when I tried to install Ubuntu 9.04 it would only recognize my 2 500 gb hds as raid. Gparted recognizes the drives as both raid and IDE. Eventually, after a day or two of praying and messing around the installer recognized both drives as raid and IDE. A couple months later here I am trying to install Ultimate Edition 1.4.
I'm renting a dedicated server with a company that claims that the server has 2 hard drives in a software RAID 1 array, but I need to make sure that the server really has the 2 HDD, and the size of the 2nd drive... how to do that ?? system is Centos 5.3
I have been battering with FC10 and software RAID for a while now, and hopefully I will have a full working system soon. Basically, I tried using the F10 live CD to setup Software RAID 1 between 1 hard drives for redundancy (I know its not hardware raid but budget is tight) with the following table;
[Code]....
I set these up by using the RAID button on the partition section of the install except swap, which I set-up using the New partition button, created 1 swap partition on each hard drive that didn't take part in RAID. Almost every time I tried to do this install, it halted due to an error with one of the raid partitions and exited the installer. I actually managed it once, in about...ooo 10-15 times of trying but I broke it. After getting very frustrated I decided to build it using just 3 partitions
[Code]....
I left the rest un-touched. This worked fine after completing the install and setting up grub, reboot in to the install. I then installed gparted and cut the drive up further to finish my table on both hard drives. I then used mdadm --create...etc to create my RAID partitions. So I now have
I'm about to install Ubuntu on two 250-gigabyte hard drives in a RAID 1 array, but I'm confused about how to partition my hard drives. How much space should I give to each partition? How many partitions should I create and where should I mount them? (I should mention that Ubuntu will be the only OS on this array.)
I want to make a RAID5 array with 4 2TB hard drives. One of the drives is full of data so I will need to start with a 3 disks and then once I copy the data from the 4th onto the array, I will then add the 4th drive. This will be my first experience with RAID. I've spent a few hours searching for info but most of what I have found is a bit over my head.
I have the newest Ubuntu installed on my machine. It currently has a 160GB sata drive. I just bought two shiny new 2TB drives that I want to RAID as 4TB. How do I go about adding these two hard drives even though install is complete? I want the 4TB assigned to my /home directory.
I have three 640GB sata hard drives that I would like to put into a raid 5 configuration. I would like to opt for a software raid 5 so its hardware independent. I was trying to follow these instructions, but they seem a bit dated.
I am currently trying to configure a set of hard drives as a RAID configuration. My system is running with Red Hat Enterprise Linux Client release 5.1 as the base OS. I am booting from CD. I am trying to image a set of drives that have not been imaged before. When the GUI dialog window for disk setup is displayed, it shows a default disk layout including a LVM slice. In the disk layout is a /boot partition already. It is not what I would like so I edit it to be the size for my system and make it the primary partition. I also select it to be a software RAID. I then add three more partitions for my drive 'A' all of type software RAID and NOT primary partitions.
At this point my drives have the correct number of partitions except for showing the LVM slice. I select 'RAID' again, followed by selecting 'Clone a drive to create a RAID device ...' followed by 'OK'. I then get a dialog to select the source and target. i select my drive 'A' to be the source and 'B' to be the target followed by 'OK'. An error dialog is received stating that all the partitions are not of type software RAID. The disk partitions are all type software RAID except the extended LVM slice. I can not get past this point and I am following a procedure written some time ago by a person that is not available.
i have cretaed RAID on one of my server RAID health is ok but its shows warning. so what could be the problem. WARNING: 0:0:RAID-1:2 drives:153GB:Optimal Drives:2 (11528 Errors)
I've been through a lot of the posts already, but nothing seems to solve my problem. I have Ubuntu 9.10 and Windows 7 dual installed (Windows was installed first). Everything has been working fine until a few weeks ago when I accidentally left a USB drive plugged in when I restarted my computer from Windows.
Ever since then, whenever I have restarted my computer from Windows grub2 has failed (it does not fail when I restart from Ubuntu). I get a varying message like Grub loading. The symbol ' ' not found. Aborted. Press any key..where the part between the single quotes is usually different each time. When this happens I have to reinstall Grub2 from a live disk, which is becoming a bit of a pain.
I've been reading around, but I don't really have a great understanding yet of how hard drives and partitions work in general, and so I haven't been able to work out what the source of this problem is.
I was recently given two hard drives that were used as a raid (maybe fakeraid) pair in a windows XP system. My plan was to split them up and install one as a second HD in my desktop, and load 9.10 x64 on it, and use the other for mythbuntu 9.10. As has been noted elsewhere, the drives aren't recognized by the 9.10 installer, but removing dmraid gets around this, and installation of both ubuntu and mythbuntu went fine. On both systems after installation however, the systems broke during update, giving an "read-only file system" error and no longer booting.
Running fsck from the live cd gives the error: fsck: fsck.isw_raid_member: not found fsck: Error 2 while executing fsck.isw_raid_member for /dev/sdb and running fsck from 9.04 installed on the other hard drive gives an error like:
The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 <device>
In both cases I setup the drives with the ext4 filesystem. There's probably more that I'm forgetting... it seems likely to me that this problem is due to some lingering issue with the RAID setup they were in. I doubt its a hardware issue since I get the same problem with the different drives in different boxes.
I have recently installed a Asus M4A77TD Pro system board which supports raid.
I have 2 x 320gb sata drives I would like to setup raid-1 on. so far i have configured the bios to raid-1 for drives, but when installing Ubuntu 10.04 from the cd it detects the raid configuration but fails to format.
When I re-set all bios settings to standard sata drives ubuntu installs and works as normal but i have just 2 x drives without any raid options. I had this working in my previous setup but thats because i had the o/s on a sepreate drive from the raid and was able to do this within Ubuntu.
I have a SATA drive that worked fine. Then I installed two more hard drives into my system. When these hard drives are installed, if I try to access the SATA drive in Linux, it will start lightly clicking and then the drive will become unavailable. If I power on the machine without the other two hard drives then it works fine. What could be causing this to happen? I don't think it's heat because the two hard drives are far away from the SATA drive.
I'm breaking into the OS drive side with RAID-1 now. I have my server set up with a pair of 80 GB drives, mirrored (RAID-1) and have been testing the fail-over and rebuild process. Works great physically failing out either drive. Great! My next quest is setting up a backup procedure for the OS drives, and I want to know how others are doing this.
Here's what I was thinking, and I'd love some feedback: Fail one of the disks out of the RAID-1, then image it to a file, saved on an external disk, using the dd command (if memory serves, it would be something like "sudo dd if=/dev/sda of=backupfilename.img") Then, re-add the failed disk back into the array. In the event I needed to roll back to one of those snapshots, I would just use the "dd" command to dump the image back on to an appropriate hard disk, boot to it, and rebuild the RAID-1 from that.
Does that sound like a good practice, or is there a better way? A couple notes: I do not have the luxury of a stack of extra disks, so I cannot just do the standard mirror breaks and keep the disks on-hand, and using something like a tape drive is also not an option.
how to migrate my whole server to larger hard drives (i.e. I'd like to replace my four 1TB's with four 2TB's, for a new total of 4TB instead of 2TB)... I'll post the output from everything (relevant) that I can think of in code tags below.
I'd like to end up with much larger /home and /public partitions. When I first set up raid and then LVM it seemed like it wouldn't be too hard once this day arrived, but I've had little luck finding help online for upgrades and resizing versus simply rebuilding from a failure. Specifically, I figure I have to mirror the data over to the new drives one at a time, but I can't figure out how to build the raid partitions on the new disks in order to have more space (yet mirror with the old drive that has a smaller partition)... don't the raid partitions have to be the same size to mirror?
Ubuntu Server (karmic) 2.6.31-22-server #65-Ubuntu SMP; fully updated
so I setup a raid ten system and I was wondering what that difference between the active and spare drives is ? if I have 4 active drives then 2 the two stripes are then mirrored right?
I just installed Debian 5.0.4 successfully. I want to use the PC as a File Server with two Drives configured as a RAID 1 device. Everything with the RAID device works fine, the only question I have belogs to the GRUB 0.97 Booloader. I would like to be able to boot my Server even if one of the disks fail or the filesystem containing the OS becomes corrupt, so I configured only the data partitions to be a RAID 1 device, so on the second disk should be a copy of the last stable installation, similar to this guide:[URL]...
My System Intel Core Duo E5300 Mobo - Gigabyte G31M-ES2L 1GB DDR2 800MHz RAM 4 x WD20EARS HDD I have been trying to install Fedora or Ubuntu for over a week. I thought it would take an hour and i would be away. I have been trying to install using the mdadm Software RAID feature. Everytime it takes about a day to format the drives and then i get an installation error. The drives state they are ready to use as is on any operating system other then WinXP, but this does not appear to be the case.
I am very new to Fedora... I have been doing some reading.[URL].. That information has been promising. I have been able to get into Fdisk off the live CD but i can't figure out how or if it is possible to do what i want it to.
Has anyone had any luck getting these drives to function correctly in a software RAID? I have had good luck with WD drives in the past and just assumed these drives would do what i wanted to but alas i have been proven wrong.
The partitions i wanted was... - A 2GB swap parition - A 10 GB RAID 1 partition for Fedora - The remaining space as a Raid 5 for files.
Am i just banging my head against a wall here, or is this possible.
I know I can simply create a degraded raid array and copy the data to the other drive like this: mdadm --create /dev/md0 --level=1 --raid-devices=2 missing /dev/sdb1
But I want the specific disk to keep the raw ext3 filesystem so I can still use it from FreeBSD. When using the command above the disk will be a raid disk and I can't do a mount /dev/sdb1 anymore. A little background info. The drives in question are used as backup drives for a couple of Linux and FreeBSD servers. I am using the Ext3 filesystem to make sure I can quickly recover the data since both FreeBSD and Linux can read from that without problems. If someone has a different solution for that (2 drives in raid 1 that are readable by FreeBSD and writeable by Linux),
Having a little problem with 10.04 installation. I have two hard drives installed on my PC. One that had Hardy Heron and one data. When the install program launches from a CD boot, it fails and drops me to a live session to check out the problem. I can see both drives and mount them but if I then launch the installer, it does not give either as an option for installation.
When i try to install ubuntu 10.04 on my desktop i get through the first 3 steps which are Language, Region, and Keyboard. when i get to Prepare partitions, there is nothing there (same problem with 9.10). I followed the steps of another thread about removing the raid settings and I am sure i did that correctly but it did not work, when i try to find my drives in terminal they can not even be found.
Both of my drives are SATA, one is 250gb, other is 500gb. They are both recognized by other operating systems. I have switched the SATA headers that they are plugged into. I really am just not sure what else to do here. Im not totally stupid at linux, ive been using it for a few years and i have taken two classes for linux in the past year. I really feel dumb for not being able to figure this out :/
Alright so i'm trying to install ubuntu 11.04 except it's not recognizing my hard drives. I have two 80gigs plugged in via sata. And neither of them are being recognized by ubuntu. I have tried plugging them in together, and separately, still nothing. I'm getting pretty frustrated. Ubuntu 11.04 just doesn't seem to be working for me. I can run from the liveCD, but i get no unity desktop environment
I am installing Ubuntu on my server that has 2 2tb disk drives. My plan for this server is to set it up as my web server (using apache), will need a mysql database and would like a ftp site. I could really use some advice on how to partition the hard drives.
I have a 4 disk raid 5 array on my Ubuntu 10.10 box. They are /dev/sd[c,d,e,f].Smartctl started notifying me that /dev/sde had some bad sectors and the number of errors was increasing each day. To mitigate this I decided to buy a new drive and replace it.I have an external 4-bay disk enclosure. I failed /dev/sde via mdadm:
Fedora is having trouble identifying a raid partition, it sees them as separate drives. I got drivers from dell, but during a Fedora dvd install, it mentions nothing about a place to install extra drivers.
When it says it must "initialize" the drives, Fedora then breaks the dell bios raid. How to either install the dell drivers or make Fedora see the raid partition as one?
i am new in Linux. i have two drives one IDE and other SATA in my computer.i want to keep windows XP , WIndows 2003 server on one drive and two flavours of linux on the other drive, let say oopen suse and redhat.please help me how i install these sofwares to make multi boot the machine.
