OpenSUSE Wireless :: New IMB Lenovo L512 - Command Is Not Correct For OpenSUSE ?
Jul 16, 2010
In the revision for the driver information it says it's for Ubuntu, but I assume it will work here as well.
Release date = 2010-05-07
Operating system release = Ubuntu 8.10/ubuntu9.04/ubuntu9.10/ubuntu10.04/moblin2/android-x86_090916
Kernel version = 2.6.28/2.6.30/2.6.31/2.6.32/2.6.33/2.6.34
Release driver version = 0017.0507.2010
Change history =
1. update firmware.
2. link NO-QOS-11N-AP use N mdoe.
3. Close LED when ifconfig wlan0 down.
4. Fix RTL8192SE WRT300N TP low issue.
5. To make LED dim time short enough when power save open.
6. Remove ubuntu10.04 self rtl8192se driver in make install.
In the supplied information from Realtek it tells me to:
========================================================================================
II. Compile & Installation & uninstall
========================================================================================
You can enter top-level directory of driver and execute follwing command to Compile, Installation, or uninstall the driver:
0. Change to Super User[code].....
When I do this the Make command is not correct for openSUSE
View 9 Replies
ADVERTISEMENT
Jun 29, 2010
I am sorry if this seems long I tried to only list the information I thought was pertinent to my wireless issue. I do get 2 of my neighbors wireless networks to show up but mine does not and it has the strongest signal by far. I have 3 other computers connected to it also on Ubuntu 10.04 LTS
lspci -nn | grep Realtek
03:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. Device [10ec:8172] (rev 10)
iwconfig wlan0
wlan0 802.11bgn Nickname:"rtl8191SEVA2"
Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated
Bit Rate:300 Mb/s
[Code]...
View 1 Replies
View Related
Jan 30, 2011
I am trying to get the wireless lan to work on a Lenovo 3000 n100. Currently the light does not come on and the card does not work. Cnet says that this computer has an intel pro wireless 3945abg however /sbin/lspci -nnk Yields 03:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01) ubsystem: Broadcom Corporation Device [14e4:0465] Kernel driver in use: b43-pci-bridge
View 9 Replies
View Related
Oct 8, 2010
I recently got a lenovo w510 laptop and I installed openSUSE 11.3 KDE on it. the wireless works fine at home (802.11g WPA2) when I go to work I have tried to set up the wifi for the 802.1X PEAP network but it doesn't look like it even tries to connect.
The work network set up is as follows. non-brodcasting SSID (do I need to tell network manager of this? I manually enter the SSID no problem)
Dynamic WEP 802.1X
PEAP
blank anonymous identity
no CA cert (I suspect this might be the problem)
PEAP v 1
MSCHAPv2
I have verified my username and pw several times, as well as the SSID. Just yesterday I helped a co-worker get on the network under ubuntu and it worked like a charm.
The Hardware profile displays the wifi card as a "WiFi Link 6000 Series" It is an intel card.
View 9 Replies
View Related
May 23, 2010
I'm all new to Opensuse, but I've used Ubuntu before, I am having some issues with my wireless on Opensuse, the laptop is connected and the WEP key is correct and in the system information it says I'm online! However the internet does not work, I know the internet is online as my main Desktop Pc (Running Windows 7 64bit) which I'm typing this on, is connected to the internet!
View 2 Replies
View Related
Nov 24, 2010
I have a Samsung ML-2525w, and have loaded the unified driver several times previously but long enough ago that I can't remember the correct command to install it. This is what I remember, in terminal viewer:
sudo ?(enter login)(then drag and drop the autorun file into the terminal viewer to install) I am going nuts trying to find the instructions again.
View 2 Replies
View Related
Jan 25, 2011
I got openSUSE installed, and now am trying to build my wireless driver, using the instructions here: [URL].
The wireless driver is here:
Broadcom.com - 802.11 Linux STA driver
NOTES:
- The (parenthesis: ) are my notes to show you what I was doing.
- Lines with "#" before them are what I typed into Terminal.
- Lines below (Output: ) are what was output by Terminal.
Code:
(run in su:)
lspci -n | grep 14e4
(output:)
04:00.0 0280: 14e4:4727 (rev 01)
(BUILD DRIVER:)
#su
<password>
# mkdir hybrid_wl
# cd hybrid_wl
# tar xzf <path>/hybrid-portsrc_x86-32_v5.100.82.38.tar.gz
# make
(output:)
if 'make' is not a typo you can use command-not-found to lookup the package that contains it, cnf make
(NOTE: with "cnf" it is saying "Cannot Find")
(install "make" command:)
# zypper in -t pattern devel_basis
(It installs 93 packages)
# make
(output:)
kbuild_nopedantic=1 make -C /lib/modules/`uname -r` /build M=`pwd`
make: *** /lib/modules/2.6.34-12-desktop/build: No such file or directory. Stop.
make: *** [all] Error 2
(Tried:)
# zypper in kernel-source
(It installed 3 more packages)
# make
(output:)
kbuild_nopedantic=1 make -C /lib/modules/`uname -r` /build M=`pwd`
make: *** /lib/modules/2.6.34-12-desktop/build: No such file or directory. Stop.
make: *** [all] Error 2
The problem might be derived from the fact I had to install openSUSE in Kernel (F6) > Safe Mode. If I need to install more things, please let me know ASAP! I am wired to my ethernet until then, which means I can't move from this spot until my wireless is working!
View 9 Replies
View Related
Feb 20, 2011
I have suse 11.3 tried to get wireless to workI issued command ifconfig and wlan0 not shown. One replier suggested that I need to get this working
View 9 Replies
View Related
Oct 24, 2009
in openSUSE 11.3 where can I put PIN for bluetooth devices pairing using just command line?
View 9 Replies
View Related
Aug 17, 2010
In openSUSE 11.3 where can I put PIN for bluetooth devices pairing using just command line?
View 5 Replies
View Related
Sep 16, 2010
Recently I got a lenovo laptop and installed opensuse 11.3 from live usb distribution, well the issue is when I want to listen to some music and plug in my headphones, the laptop speakers do not turn off automatically.
View 9 Replies
View Related
Dec 15, 2009
I just bought a brand new Lenovo Y550 Ideapad with the following specs:
Intel Centrino 2 2.53ghz
4gb DDR
GEFORCE GT 240M 1GB video card
I bought it blank and installed Opensuse 11.2 Gnome 64bit as the main OS (using it right now). Using the "long method" instructions found on this website, I installed the Nvidia 190.42 graphics driver from the Nvidia website. It is working perfectly. My OS worked great for a while (love it), but now I am unable to boot up completely into Gnome. The bootscreen goes fine until I get past the automatic login screen for gnome, then the display stays on the default green background. My lights indicate that my computer is working, but no panels or icons load onto the desktop. After about two minutes, a notification pops up saying that I am connected to the wireless network, but there are still no panels or icons on the desktop. My mouse pointer works fine, so I know that the display is not frozen. I end up having to shut off my computer and restart it. Usually this takes two tries before the Gnome desktop completely loads and I am able to use my computer. I'm relatively new to Linux, so if I need to do anything "fancy", you'll probably have to be patient with me and walk me through it
View 1 Replies
View Related
Mar 14, 2010
I have tried installing 11.2 64 bit with Gnome. Every time if finishes the install and reboots it will start HAL daemon and just black screen. I have tried loading with using the number 3 with no video. Same thing black screen after loading HAL daemon. I did a install with selecting VESA same thing.
View 9 Replies
View Related
Jun 8, 2011
I have a Lenovo T410 laptop. I'm unable to find drivers for the ethernet card, the wireless card and graphics. I don't even know what hardware is installed in the system. Here is the product ID if it can help in identifying the hardware.
Product ID : 2516CTO
View 9 Replies
View Related
Dec 7, 2010
Im considering installing Open Suse linux on my laptop - Lenovo Thinkpad T510i. Will all the devices be recognized?
View 2 Replies
View Related
May 6, 2011
I'm trying to install openSuSE 11.4 onto my brand-new Lenovo W520 laptop, using the Intel Rapid Storage Technology (FakeRAID?) controller, ROM version 10.1.0.1008. I have 2 physical 500GB disks configured in a mirror (RAID-1). Everything looks fine, the installation program comes up and asks if I want to use mdadm to manage the RAID, to which I answer yes. I go through the normal setup screens, and select the partition layout that I want (for sake of this post, I'll limit myself to the layout that the system itself recommends).
The problem comes when it becomes time to format the partitions. Somehow the partitioning program gets it into it's head that the root partition is 10TB, not 20GB, and the ext4 partitioning fails in various ways (short reads to sector zero, unable to map using 4096 byte sectors, etc, etc) depending on exactly which partitioning scheme I'm attempting. I pretty much get the same result no matter how I play the partitions, which file systems I use (XFS, ext4, etc [of course, I can't use XFS for /boot...]).
For now I've gone ahead and set myself up using software RAID, since this system is unlikely to become dual-boot with Windows for a few years at least. (As an aside, but as a hint to others, when the installation fails, I end up having to go back into the Intel RAID controller BIOS boot to clear out the entire RAID setup each time it fails - the disks are left in a completely useless state).
View 5 Replies
View Related
Jun 27, 2011
I have installed opensuse 11.4 in my lenovo ideapad G460. But, I am not being able to make the inbuilt microphone work. It does not record anything and also does not work in skype. I am not that expert with linux. I looked at different posts in this forum regarding microphone detection problem, bit could not follow. How to setting up my inbuilt microphone?
View 6 Replies
View Related
Sep 12, 2010
I want to install a driver for the Mobile broadband HSDPA modem of the Lenovo T510 nootebook because it dosent work with the Networkmanager.
I use opensuse 11.3 whith the kernal 2.6.34-12.
So what i want to do:
1) get attached patch
2) install and extract kernel source
3) patching and compilation (only drivers/usb/serial subdirectory)
4) copy resulting modules to kernel modules directory
If I compile: make O=../temp prepare i get a mistake.
The exactly mmessage is:
View 1 Replies
View Related
May 12, 2011
When I learn shell script, I want to add my own PATH variable to system previous variables. I find that my linux has the below PATH variables (in the end of this message). It shows 'No such file or directory' although I verify that all the directories exist. Some directories are empty indeed. This will result that warning?
I want to make the present PATH variables correct before I add mine.
bash: /usr/lib/mpi/gcc/openmpi/bin:/home/jeff/bin:/usr/local/bin:/usr/bin:/bin:/usr/bin/X11:/usr/X11R6/bin:/usr/games:/usr/lib/jvm/jre/bin: No such file or directory
View 9 Replies
View Related
Jul 8, 2011
I tested OpenSuse 11.4 as a guest OS via virtualbox on a win7 32bit host. Output to my 16:9 screen was perfect with a plentiful choice of high resolutions. Now with Suse (32 bit) properly installed as the host the only resolutions are 1024X768 and below and I am stuck with 4:3 ratio. My PC is an Intel Atom D945GCLF2 which has integral graphics. The monitor is the VGA input of a Samsung TV.
View 9 Replies
View Related
Dec 27, 2010
I'm a KDE3 user who just upgraded to 11.3/KDE4 and is still trying to learn the new way of doing things, so please bear with me if I've overlooked something obvious. I've managed to mostly get my desktop the way I want it, except for one problem: I want to add a submenu to the panel, with an appropriate icon.
According to Bug 189583 - Ability to add submenu "like editors" to kicker panel from classic menu this capability was added over a year ago, so I should be able to just right-click on any submenu and the option to add the submenu to the panel or desktop should pop up. Except for me, it doesn't. Right-clicking on a submenu just selects the first item in the submenu instead of bringing up the context menu. I've tried both the classic and kickoff menus, and the same thing happens.
The bug report does mention it is also possible to add a submenu to the panel from Dolphin by going to applications:/ and dragging the folder to the panel. This does add the submenu, but the icon displayed on the panel is the question mark icon, and there seems to be no way to change it. Besides being ugly, I need different icons to tell different submenus apart.
View 9 Replies
View Related
Jan 11, 2010
How do i find the correct path to my cd-rom drive? I want to install office 2007 using wine and I have used the programmerfish tutorial and now have to do the following:type wine /path to cd/setup.exe but I cannot seem to find the correct path.
-I tried /dev/sr0/setup.exe but it returned an error.
-I tried /dev/sr0/media/setup.exe. returned the same error.
-I tried /dev/media/setup.exe. Also no good.
I thought using df would help me and there i found /dev/sr0/ would be my cd-rom drive. Dunno it this correct though.
View 9 Replies
View Related
Dec 7, 2010
How I setup my NetworkManager to use the correct host name on my system, if that is possible. NetworkManager ignores the specified hostname and uses 'localhost', which is a bit annoying.
View 9 Replies
View Related
Jan 10, 2010
I formatted a external 160 GB HDD (Lacie) with EXT3 and encrypted. The formatting went perfect. When I stick it into the USB slot, it is recognized and mounted by HAL. Hal asks me the password and then everything seems ok. But I have no write access. Only root has. I would like to use it to store my user data, externally, but encrypted. How can I set the write permission to make this possible? Why does HAL attribute the write permissions to root, even if I have given the password as user?
Filesystem EXT3
Opensuse 11.1
KDE 3.5
View 9 Replies
View Related
Feb 11, 2011
had trouble writing to a flash drive. checked the permissions, the correct user it there, but the id is root.when logged in as root and attempt to change permissions i get Could not modify the ownership of file /media/disk-3. You have insufficient access to the file to perform the change.
now how as root can not have enough permission? i've been up and down the forums and google to no avail. poked around in the fstab and even mtab as there are two files, one a lock, that seems to come from mtab.
View 9 Replies
View Related
May 3, 2011
What is the correct/safe way to move from upstart to systemd? I originally installed upstart in 11.3 and have now upgraded to 11.4. Having successfully upgraded to 11.4 I tried to use yast2 to install systemd and systemd-sysvinit onto my running system. Yast correctly identified that upstart should be deinstalled as a prerequisite for installing systemd-sysvinit.
After the install of systemd the system wouldn't shut down, and on a reset the system reported many systemctl/start service timeouts on things such as mounts and ttys. Eventually the system started an X-windows KDM login, but there were no console ttys and mounts were missing. I used X/kdm to login to root - phew! - I restored / from an rsync backup I'd made prior to the changes, so I'm back in business with upstart. I'd like to tidy up and move to systemd - I going to have a nose around myself, perhaps I will try switching back to sysv init and then going to systemd - but I have to wait for the machine to be idle before I experiment, any info in the mean time would be great.
View 3 Replies
View Related
May 7, 2010
i am running openSUSE11.2 which is fully updated.only problem is that it wont play my audio throught the correct ports.it plays everything clear on the front ports but not the back ports.please inform me if there is a package or application that will help me fix this problem.
View 5 Replies
View Related
Nov 8, 2010
Had a well working sound system until I bought a USB webcam with microphone. Sound still works well except with flash. As mentioned here my problem is making flash use my normal sound card instead of the USB webcam microphone.
View 2 Replies
View Related
Apr 6, 2010
I have a problem with the fritz!wlan usb stick. I have installed itth success on another PC by using instructions published here Ndiswrapper - openSUSE.Today I have decided to erase WindowsXP from my wife's computer (that is an identical to the one I use). So I have downloaded the OpenSuse 11.2 DVD and I have performed a completely new installation from DVD.After installation has been executed with success, I have decided to install an internet connection using the istructions above. I told to myself: "it will take 5 minutes, all I must to do is to reply action I have done one month ago... the internet usb-stick is the same, so it will be easy to replicate the process..."I was wrong... When I reach the point where I must "modprobe" the ndiswrapper module I receive what follows:
Code:
linux-2n4g:/home/mila/Desktop # modprobe ndiswrapper
WARNING: All config files need .conf: /etc/modprobe.d/ndiswrapper, it will be ignored in
[code]...
View 7 Replies
View Related
Feb 25, 2010
I just installed OpenSuse 11.2 3 months ago on my laptop. I'm running with the Gnome Desktop. I live in Chicago and am currently in London. When I set the timezone to Europe/UK the date/time are correct UNTIL I reboot the laptop. After reboot if I type in the 'date' command it shows the time at 6+ hours from London time. When I check the hardware clock 'hwclock' it displays the correct London time. I check the time setup with yast and it shows the correct Timezone but again shows the 6+ hours difference. I change the time in yast and and my applications ( e-mail) display the correct local time again... UNTIL I reboot and then I'm right back where I started - wrong local time ! I suppose I could write a little startup script to do a 'hwclock --hctosys' but I thought I'd check here first to see if anyone out there had any ideas..BTW - I hate to say this but on the same laptop running XP I don't have this problem AND I didn't see this problem in OpenSuse 10.3 or 11.1
View 9 Replies
View Related
