just downloaded gkrellm and I go to set the temperature sensors and I get "No Sensors Detected" now I've never dealt with something of this nature before so can anyone tell me where I might begin with this one?
View 9 RepliesI recently assembled a Dell T5400 workstation. I'm getting some strange issues with this machine concerning fan controller.
-Only 2/4 motherboard fans are detected. All fans have RPM signal
-The only sensors that are reporting temperatures are for the memory modules,graphic card and disk but not from my Intel CPU's. This chip reports memory module temperatures as they tend to get pretty hot (DDR2-FBDIMM).
-Every time a fan speed gets reported with sensors command the bus freezes for a moment. Videos playback and audio chops for a moment and continue normally.
After removing module dell_smm_hwmon the sensors command executed without interrupting multimedia flow but no fan speeds were reported also.
As a temp solution I blacklisted the dell_smm_hwmon module and I solved the high fan noise problems and the bus freeze.
As it turns out i8k module for fan control is very buggy for some DELL models. Can I manually configure it somehow to work?
So to sum up the problems my problems are:
No CPU temperatures reporting. 2 Fans Speed and PWM controller info missing, and freezing the bus when probing to get speeds from those identified (dell_smm_hwmon module issues).
The object is to get fancontrol working in my setup.
I run debian testing with kernel 4.2.0-1-amd64.
LM-Sensors can't seem to pull any info on the temp sensors for my new MSI H61M-P21(B3) mobo. Is MSI just not Linux friendly? Or could it possibly be that there really are no temp sensors on this board? I must be missing something simple here
View 9 Replies View RelatedAfter Kernel upgrade, sensors-applet doesn't display the hd temp. To fix the problem I have to remove and after reinstall hddtemp package.
View 5 Replies View RelatedI recently built a cluster with Centos 5.3 and nodes that used different versions of the w83627ehf sensors chip. On some nodes sensors-detect detected the chip:
Found `Winbond W83627DHG Super IO Sensors' Success!(address 0x290, driver `w83627ehf')
But starting lm_sensors returned the error: Starting lm_sensors: No sensors found!
On other nodes sensors-detect did not detect the chip at all: Found unknown chip with ID 0xb073(logical device B has address 0x290, could be sensors)
[Code]....
I tried yum install pidginyum updateyum clean allJust hangs, I do see a tmp dir? not sure where to go from here. --> Finished Dependency Resolution
[Errno 2] No usable temporary directory found in ['/tmp', '/var/tmp', '/usr/tmp', '/root']
[root@SilverFox ~]# cd /
[root@SilverFox /]# ls
[code]....
I just recently changed my motherboard, and now the command "sensors" shows "no sensors detected" I ran sensors-detect but still i get no sensors detected.
View 9 Replies View RelatedI can't for the life of me get the xsensors to work. I installed lm-sensors, the applet and also xsensors.I followed everything on this guide:URl... Went through it more than twice and a couple of restarts. I just can't figure out what's wrong.When I run "sensors" nothing is found. I ran the sensors configuration and it only found one device to add to /etc/modules. Please see the trace below, I would be very grateful if you can help me find the fix for this! The desktop is an HP Pavilion a730n with a Pentium4 processor.
View 3 Replies View RelatedI have a web server whos DocumentRoot is:/tmp/wwwNow, /temp/www/fake/ is a directory that contains a series of other files/folders.What I want to do is access the files in /temp/www/fake as if they were in the root directory (/temp/www/)For example:
could either be located in "/temp/www/test.php"
-or-
located in "/temp/www/fake/test.php"
so "http://127.0.0.1/test.php" would essentially call both directories. Is this possible? Whould I do this through apache or through the actual file system somehow? (Like some sort of symbolic link?) I would love to hear your input.
I would like to use lm-sensors with my new PC.With my old one lm-sensors showed all sensors of CPU, GPU, wattage and Fan.With the new AMD64 (kernel 2.6.32-5 on Debian Squeeze) I get only the temperature of the GPU and the HDD.The only found sensor is "Fintek F71882FG/F71883FG Super IO Sensors"No embedded "AMD [...] thermal sensors" found in sensors-detect How can I fix it?sensors-detect
Code:
#
# sensors-detect revision 5818 (2010-01-18 17:22:07 +0100)
[code]...
Im having some trouble getting sensors to work on kernel 2.6.33.
This is what i have at sysconfig under lm_sensors:
Code:
When i do /etc/init.d/lm_sensors restart i get this:
Code:
I know k10temp driver is now included on kernel 2.6.33 so i dont know what to do.
I have just recently installed opensuse 11.3 on my computer. I have switched from Ubuntu and have been trying to get things configured similar to what it was. One problem I have encountered is with installing sensors and k10temp, the module needed to monitor my CPU temp. within Linux. I have an AMD sempron and a biostar mcp6p m2+ motherboard. I have installed package "sensors" and have run the sensors-detect and it went through and found k10temp that I would need to load within the kernel for this to work properly. I had this working in Ubuntu, but not sure how to do it in openSuse. I have tried compiling the k10temp source, running modprobe k10temp and received no output, and looked around the conf files, but not sure how to go about doing it?
View 2 Replies View Relatedlm_sensors failed after configuration by sensors-detect.
server3:~ # rclm_sensors start
Starting up sensors: failed
/etc/sysconfig/lm_sensors
[code]....
Where are temp files stored in SuSE 11.0? I am trying to find all of those videos and .jpgs and other miscellaneous files I've downloaded in the past, and which are now only taking up space on my hard drive. I'd like to clean out all of that. I have looked in both /tmp and in /.kde but don't see what I'm looking for.
View 9 Replies View RelatedI just downloaded hddtemp and ran it and got:
/dev/sda: 43C
/dev/sdb: 48C
Is this bad/ok?
how to clean up tmp files on opensuse 11.4 as it seems as if the partition is almost completely file of various files.
View 4 Replies View RelatedI have hdparm running and see the reading in gkrellm
.dev/sda = 36 celcius
in messages
smartd[2895]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 108 to 107
Where to change that smartd reading?
I'm using Opensuse11.4 and have kmail and Firefox. When I click a url: link in kmail it opens a new tab in Firefox. The problem is that the url is linked to my temp cache files as this file:///var/tmp/kdecache-terry/krun/1589.0.ctt
The tab this opens has most of the link icons stripped out and the links to other parts of the website don't work and I get a "file not found" error and the link is to a file which doesn't exist file:///contribute.php3
This is only a minor annoyance as I can right click > copy the url and paste it to the address bar in Firefox then it works ok. I don't think it anything in either programme that's broken because this happened after an update to Opensuse 11.4 on my previous laptop and has happened again on my new laptop with a fresh install.
I'm looking to use a vnc client so I can connect to my other windows machine. I thought i'd use realVNC as I've used it before from windows and it seems to do the job... the problem is that when I try and install it I get the following message: Package /temp/vnc-4_1_3-x86_linux.rpm could not be installed.
Details: Subprocess failed. Error RPM failed:error: Failed dependencies: libstdc++-libc6.2-2.so.3 is needed by vnc-4.1.3-1.i386
Is it a problem that I'm trying to install this on a 64 bit Suse 11.1 installation? Can anyone recommend a solution (I can't find the package to install), or any other good vnc clients I can easily use?
I installed a program with Yast (Kmess), but when I try to run it, bash gives me back this message:
Code: kmess: command not found I checked into Yast and it seems to be installed correctly!
After I ran sensors-detect, it said that İ needed k10temp module to be compiled, so I searched some forums and got required stuff. However, before compiling it, I added the gnome applet for sensors to the panel, and surprisingly it shows the cpu and motherboard temperatures. How reliable it is? Do I still need to compile k10temp? (I will compile it since I don't want to use a kernel from experimental repo).My kernel is 2.6.32-5-amd64, TestingCPU: AMD Phenom 2 x4 955 BE
View 2 Replies View Relatedi moved on ubuntu 9.10 Karmic, before on 9.04 All sensors work fine but now only "coretemp".so ran "sudo sensors-detect" and output result is:
Code:
#----cut here----
# Chip drivers
[code]....
I had previously installed lm-sensors and the associated files on my Lattitude 2100 when I was running 8.10 and got a great little bargraph readout thing at the bottom of the screen that helped me monitor system temperatures. Now that I've upgraded to lucid lynx netbook, I can't seem to get the same thing going. I installed the lm-sensors etc. but the applet/readout/display whatever you want to call it, is nowhere to be found.
View 8 Replies View Relatedcontrol my cpu fan speed? It's really loud, and I'm not stressing the CPU at all, but it seems to be running at 110% all the time.
I've tried going through some old posts related to lm-sensors but nothing seems to work.
I'm using an Asus motherboard (M4A88TD-M), an AMD 1075t six-core processor, and I have Ubuntu 10.10 installed. Ive run sensors-detect, followed the onscreen prompts... the output looks like this:
Code:
# sensors-detect revision 5818 (2010-01-18 17:22:07 +0100)
# System: System manufacturer System Product Name
# Board: ASUSTeK Computer INC. M4A88TD-M EVO
[Code]....
I have tried lm-sensors and a few others, firefox just crashed.
Phenom II X6 1090T
MSI-890FXA-GD70 motherboard
Ubuntu 10.10
Senors:
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +0.0C (high = +70.0C)
sensors-detect
Now follows a summary of the probes I have just done. Just press ENTER to continue:
Driver `k10temp' (autoloaded):
* Chip `AMD Family 10h thermal sensors' (confidence: 9)
No modules to load, skipping modules configuration.
Unloading i2c-dev... OK
There is a debugging panel on my motherboard, and I think that that displays the CPU temperature, although I am not sure.
I installed lm_sensors via Synapt & the Sensors Applet on the panel, but that applet shows me an invariable 40�C for 2 temperatures - 'CPU' & 'temp1'.Now I know it can't read the CPU temperature (long story, the CPU fan is hard-wired to 6v & there is no temperature feedback...) but it should be able to find a couple of other useful temperatures.The same PC in XP uses Speedfan which indicates plausible temperatures for (I think) Case & Hard Drive. (Temp2 & HD0 in the attached)I wonder what I have failed to do & why I cannot see Case or HD temps in Ubuntu?In terminal, I ran sensors-detect which went OK until the last bit where it said:
"~$ /etc/init.d/module-init-tools start Rather than invoking init scripts through /etc/init.d, use the service(8) utility, e.g. service module-init-tools start...etc" I don't follow that, but I have checked that I have it87 in both /etc/modules & in lib/modules/.../hwmon
FC13 sensors not workingsensors-detect gives:Some south bridges, CPUs or memory controllers contain embedded sensors.Do you want to scan for them? This is totally safe. (YES/no):
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
[code]....
I installed Karmic 64-bit on a new Phenom X4 Quad-Core PC. I've replaced the stock CPU cooler with a Cooler Master Hyper TX3, enabled all fan control settings in the BIOS, switched their profiles on silent, enabled the Cool n' Quiet option as well but my CPU fan is still noisy and seem to be running up to the max number of RPM, thus ignoring BIOS specifications. Besides this I can tell there is something wrong with it since even the CPU is on idle or with just the regular browsing, media player operations, PC sometimes freezes or is automatically rebooted .
I installed lm-sensors and went through all the sensors-detect operations (output attached to this post) but it doesn't show anything else but the CPU and HDD temperature which is always 40 Celsius degrees.
I'm running ubuntu 9.10 64 bit on a Dell Latitude E6400 with the following configuration:
Intel(R) Core(TM)2 Duo CPU P8700 @ 2.53GHz, 3MB L2 Cache 1066 MHz
Intel Graphics Media Accelerator x4500HD
4GB RAM
250 GB Hard Drive SATA 7200RPM
I'm experiencing overheating problems, after just 15-20 minutes of minimal use (surfing the internet, not even watching flash vids or any other vids). The same laptop under Windows 7 64 bit stayed really cool.
I've read several posts here and followed this manual: [URL] to try to control the fans (I only installed the lm-sensors and ran the sensors command, I didn't do anything beyond that). Specifically what I did was install lm-sensors (via apt-get), ran sensors-detect which advised me to add the coretemp module to /etc/modules, which I did.
However when running sensors the only information I get is the overall temperature and the temperature of each of the cores.
why I'm not getting fan speed info when running sensors? Also is there a way to find out if more modules needs to be added to /etc/modules?
I installed Sensors Applet & hddtemp. Installation was smooth, all of my devices were automatically detected and all seemed good.Then I restart the computer, and when everything comes back up, the processor, MB, and GPU are all working (showing a temperature) but none of the (6) hard drives are showing a temperature. After fiddling around with it I found that removing the applet from the panel, and then adding it back again fixes the problem. But then the next time I restart the computer it breaks again.
View 1 Replies View Related