Debian Hardware :: Dell T5400 Fan Controller And Temp Sensors
Nov 19, 2015
I recently assembled a Dell T5400 workstation. I'm getting some strange issues with this machine concerning fan controller.
-Only 2/4 motherboard fans are detected. All fans have RPM signal
-The only sensors that are reporting temperatures are for the memory modules,graphic card and disk but not from my Intel CPU's. This chip reports memory module temperatures as they tend to get pretty hot (DDR2-FBDIMM).
-Every time a fan speed gets reported with sensors command the bus freezes for a moment. Videos playback and audio chops for a moment and continue normally.
After removing module dell_smm_hwmon the sensors command executed without interrupting multimedia flow but no fan speeds were reported also.
As a temp solution I blacklisted the dell_smm_hwmon module and I solved the high fan noise problems and the bus freeze.
As it turns out i8k module for fan control is very buggy for some DELL models. Can I manually configure it somehow to work?
So to sum up the problems my problems are:
No CPU temperatures reporting. 2 Fans Speed and PWM controller info missing, and freezing the bus when probing to get speeds from those identified (dell_smm_hwmon module issues).
The object is to get fancontrol working in my setup.
I run debian testing with kernel 4.2.0-1-amd64.
View 0 Replies
ADVERTISEMENT
Aug 7, 2011
LM-Sensors can't seem to pull any info on the temp sensors for my new MSI H61M-P21(B3) mobo. Is MSI just not Linux friendly? Or could it possibly be that there really are no temp sensors on this board? I must be missing something simple here
View 9 Replies
View Related
Jan 22, 2010
just downloaded gkrellm and I go to set the temperature sensors and I get "No Sensors Detected" now I've never dealt with something of this nature before so can anyone tell me where I might begin with this one?
View 9 Replies
View Related
Jun 30, 2010
After Kernel upgrade, sensors-applet doesn't display the hd temp. To fix the problem I have to remove and after reinstall hddtemp package.
View 5 Replies
View Related
Sep 4, 2009
I'm running into this issue after installing Fedora Core 11 off DVD. Anaconda install the first part of the installation, then after reboot it goes into run level 3 (I think, where you have to login as root) I noticed that it said xserver failed to load before it actually boots Anaconda.
Maybe I should pull a graphic's card? I have logged in as root after the base install and did a lspci, and you can see the two Nvidia Quadro FX1700's and you can tell it is an intel board with the Intel Corp 6311ESB/6321ESB PCI Express ports. Also you can navigate through the linux directories via ls \. I tried YUM to find/install the graphics drivers but it says something about metadata not being configured. I checked the IP address with ifconfig and had to manually assign an ip.
View 14 Replies
View Related
Feb 23, 2010
I just got a dell studio 1557 with core i7 processor. I have heard they run warm and suspect this one is no exception but am having a hard time monitoring the temps. When doing acpi -V i can see 2 thermal zones (0,1) with the first being 63C and the second always staying 26.8C. When I am doing a lot of processing the first thermal zone jumps up quickly. First, should that be the processor temp? Secondly, any way to get more accurate readings with lm-sensors(sensors-detect can find no monitoring items).
View 5 Replies
View Related
Jun 27, 2010
I have a Dell Precision M4500, Intel Core i5 CPU, running Linux (Ubuntu Lucid), and would like to keep an eye on CPU temperature. I've tried lm-sensors: sensors-detect didn't find any sensors; following its hint ("This is relatively common on laptops, where thermal management is handled by ACPI rather than the OS.") I tried acpi -V but got nothing thermal. The Gnome panel applet "Hardware Sensors Monitor" reports on GPU temperature but nothing else.
View 3 Replies
View Related
Mar 3, 2011
I can't for the life of me get the xsensors to work. I installed lm-sensors, the applet and also xsensors.I followed everything on this guide:URl... Went through it more than twice and a couple of restarts. I just can't figure out what's wrong.When I run "sensors" nothing is found. I ran the sensors configuration and it only found one device to add to /etc/modules. Please see the trace below, I would be very grateful if you can help me find the fix for this! The desktop is an HP Pavilion a730n with a Pentium4 processor.
View 3 Replies
View Related
Jul 2, 2010
megaraid controller and Dell2850, all that I can see on thi screenshot:
[URL]
All drives successfuly passed verifing from LSI controllers (Ctrl+A at startup), also I tried to boot from rescue llive cd and mount all the morrored drives and check it by fsck - ok.
View 5 Replies
View Related
Oct 4, 2010
I am trying to install Centos onto a Poweredge 2650, with Dell Poweredge Expandable Raid Controller. I have 5 SCSI disks installed, and have created and initialised 2 logical volumes via the SCSI controller setup utility (Ctrl M after boot). After reboot the system reports two logical volumes present.
The Centos installer cannot find any disks when it gets to the disk partitioning/setup step. It reports no disks present. Do I need a specific driver for this controller?
View 2 Replies
View Related
Dec 20, 2010
I have a web server whos DocumentRoot is:/tmp/wwwNow, /temp/www/fake/ is a directory that contains a series of other files/folders.What I want to do is access the files in /temp/www/fake as if they were in the root directory (/temp/www/)For example:
could either be located in "/temp/www/test.php"
-or-
located in "/temp/www/fake/test.php"
so "http://127.0.0.1/test.php" would essentially call both directories. Is this possible? Whould I do this through apache or through the actual file system somehow? (Like some sort of symbolic link?) I would love to hear your input.
View 8 Replies
View Related
Jan 8, 2010
I am using Dell Inspirion 1545 core 2 duo T6600, 3 gb ram,320 gb sata hddand in my bios i got 4 option (1) disable which disable sata and hdd is not detected (2) ATA where in my M$ is working(3) AHCI which mode will work. also i am using vm-ware to installed redhat linux 5.my hdd did not detected. do u need any information tell me i will post it on the same any command out put or log by which we can solve this problem.
View 1 Replies
View Related
Jun 21, 2010
I would like to use lm-sensors with my new PC.With my old one lm-sensors showed all sensors of CPU, GPU, wattage and Fan.With the new AMD64 (kernel 2.6.32-5 on Debian Squeeze) I get only the temperature of the GPU and the HDD.The only found sensor is "Fintek F71882FG/F71883FG Super IO Sensors"No embedded "AMD [...] thermal sensors" found in sensors-detect How can I fix it?sensors-detect
Code:
#
# sensors-detect revision 5818 (2010-01-18 17:22:07 +0100)
[code]...
View 3 Replies
View Related
Jan 6, 2011
After I ran sensors-detect, it said that İ needed k10temp module to be compiled, so I searched some forums and got required stuff. However, before compiling it, I added the gnome applet for sensors to the panel, and surprisingly it shows the cpu and motherboard temperatures. How reliable it is? Do I still need to compile k10temp? (I will compile it since I don't want to use a kernel from experimental repo).My kernel is 2.6.32-5-amd64, TestingCPU: AMD Phenom 2 x4 955 BE
View 2 Replies
View Related
Mar 23, 2010
I have an issue with IBM XSeries 236M rack server running Debian Squeeze (2.6.32-3-vserver-amd64). I have installed "lm-sensors", "fancontrol", "acpid" and "acpi-support-base" packages. The problem is that I cannot get fan voltage and RPM displayed.
Command "sensors" will only display core temperatures:
root@xseries:/home/yang# sensors
k8temp-pci-00c3
[code].....
View 3 Replies
View Related
Jun 3, 2010
I have Debian Squeeze with Gnome "sensors-applet" installed.I have a Nvidia 7300GT GPU whose Thermal Monitoring(Temperature) is Shown fine on "nvidia-settings" GUI. But ,Sensors Applet in Debian shows only CPU temp and if I install hddtemp,it will show hard disk temperatures.
I ended up rebuilding the package from debian source enabling nvidia support.and it worked(with "DEB_BUILD_OPTIONS="--enable-gui --with-nvidia" Has Any Work Around to show nvidia GPU temperature without rebuilding the package ?PS:Below is a screenshot of nvidia GPU temperature showing in the top panel(of Gnome). sensors-applet_nvidia.png (5.5 KiB) Viewed 518 times
View 1 Replies
View Related
Aug 4, 2011
Having installed the 2.6.32 backport for Lenny, I have suddenly noticed that my Gkrellm doesn't display CPU and MB temperature anymore. Also, the smart sensors are inaccessible. Smartctl cannot access the readings even when run manually in a root terminal. I tried reinstalling lm-sensors and running sensor-detect again but it didn't help. What else needs to be updated to let the backported kernel see the hardware sensors?
View 4 Replies
View Related
Mar 17, 2010
I just recently changed my motherboard, and now the command "sensors" shows "no sensors detected" I ran sensors-detect but still i get no sensors detected.
View 9 Replies
View Related
May 10, 2015
I am noticing some rather high CPU temps while using Debian 7.8 KDE on a Lenovo X200 laptop.
Even when its not doing anything its getting as high as 70C sometimes. I opened it up and went in with a can of compressed air, it went down a little to 36C now its back to 70c the day after.
Then I realised the fan was hardly spinning is there any way I can control how much (or little) the fan spins at certain temps?
My guesses are it could be done with a bash / shell script in the kernal loaded at booting up. But am unsure.
Here is my dmesg [URL] ....
And lsmod [URL] ....
View 2 Replies
View Related
Apr 6, 2015
Bizarrest thing after swapping in my HDD from an old laptop into a new one. My LXDE panel temperature display is showing "-273," AKA absolute zero in celcius. I've done a bit of googling for lxde temp sensor, and most of the discussions I saw referred to installing lm-sensors, which apparently I did not yet have, although on my old laptop the temperature was shown correctly. I believe the automatic sensor location is off and I need to give it the correct location manually. I am unsure of how to do that, and it makes sense that it's hardware specific. After installing lm-sensors, I saw that sensors-detect provides me with a list of the correct temp sensors in my computer, but I'm unsure how to save those results so the computer can use them.
View 5 Replies
View Related
Jun 18, 2010
I can not get the node or cloud controllers to startup using the init.d scripts. I have a fresh install of CentOS 5.4 with Eucalyptus 1.6.2 I have compiled Eucalyptus and all packages using the RPM supplied from Eucalyptus and utilizing yum installer. I do not currently have any processes or applications listening currently on the ports on the boxes as well. I think it may be a permissions issue or something because I get a "permission denied error", but I am not sure if it is Eucalyptus or CentOS. It looks as if it is not binding to the address on the interface of the NIC. It may be something else however. I have the Node controller, Cloud controller, and Cluster controller on seperate physical boxes. When I try to run either the cloud controller or the node controller I get this message:
Cloud Controller:
[root@cluster-cont ~]# /etc/init.d/eucalyptus-cc start
Starting Eucalyptus cluster controller: (13)Permission denied: make_sock: could not bind to address [::]:8774
(13)Permission denied: make_sock: could not bind to address 0.0.0.0:8774
[code]...
View 2 Replies
View Related
Sep 15, 2010
Basically i want it so that the analogue stick on my PS2 controller, which connects via a USB adaptor and is recognized, correctly controls in game characters. It seems to work fine enough in platformers, at least it does with Banjo Kazooie, but with games like perfect Dark it seem to be trying to move forward and look down at the same time, also backward and look up simultaneously and look sideways and move sideways simultaneously , rendering the game all but unplayable.
I have tried running jscal and, apart from the fact that it seems a bit beyond me, it reports "jscal: missing devicename" when i try to run "jscal -c". Do others out there have there analogue sticks working correctly with games like Perfect Dark, or the James Bond games, for example?
View 4 Replies
View Related
Jul 21, 2010
I've bought a small embedded controller running with a minimized Lenny for armel. Minimized in a way that there is even no apt-get or dpkg installed on it, due to keep the memory footprint as small as possible.Is there a way to keep a "shadow" system in a directory on my Laptop (e.g. ~/armel), maintained with dependencies by a package manager like apt-get? This would allow to install addition packages including all dependent with a simple apt-get call.Of course, later I have to put the whole tree from my Laptop towards my embedded controller. I've already tried the following:Setup a directory tree behind ~/armel for apt by a copy from my laptops Lenny
"sudo apt-get -o DIR=~/armel -o APT::Architecture=armel update"
to get the repositories, this works fine
"sudo apt-get -o DIR=~/armel -o APT::Architecture=armel -d -f install"
to download the full list of .deb packages, this works fine
[code]...
View 3 Replies
View Related
Mar 31, 2011
It is possible to use the sixaxis as a joystick. But how?
For a year and a half I've been trying to get sixaxis working on ubuntu, and there appear to be even less options on debian.
While this page suggests there is kernel support, usbmon doesn't show any packages coming down the line at all (But lsusb does recognize the device)
So how do I get debian to recognize the sixaxis?
View 3 Replies
View Related
Aug 2, 2010
Recently we bought a server machine in purpose of hosting game servers.Debian is the optimal choice for us but we have a huge problem.We have 2 x HDD Fujitsu MBA3300RC, 300GB, 15000rpm, 16MB [MBA3300RC] , but NO SAS-controller , so standard Debian DVD1 didn't recognized our HDD's during installation.Is there any way to install Debian on our machine without haveing to buy a SAS-controller? answer in "step-by-step" method, i am not very experimentated in linux.
View 2 Replies
View Related
Apr 26, 2010
Does Debian have any particular tools or nuances for installing new hardware? I saw some stuff on Ubuntu which is related... but you know.
The dmesg file shows that it's being recognized, but I don't think it's actually being used (i.e. there is no driver installed). This is what's in the dmesg file:
Code:
[ 1.384634] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.855496] SCSI subsystem initialized
[ 5.146598] scsi0 : ioc0: LSI53C1020A A1, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=16
[Code]....
Unless someone has already compiled a driver for Debian Lenny for this hardware, I'm going to have to compile my own I guess. The driver package seems to come with something called mptlinux-4.00.43.00-src.tar.gz which I'm guessing can be compiled for any Linux, but looking at the instructions, it's pretty much beyond me how to get started. It talks about using kernel source to build a module and such and such.
View 3 Replies
View Related
Apr 28, 2009
At the school i work in i have a server2k3 server that provides a domain to all the windows clients, aswell as a fedora server that acts as an imaging machine and webserver.
Im rather concious of the fact that if for any reason the Server2k3 server was to die there is no backup of active directory, or anything that can take its place whilst a replacement is found.
So is it possible to use a fedora machine with samba as a secondary domain controller? so it can be used as a login server, and has a copy of AD.
View 1 Replies
View Related
Feb 18, 2010
Can Debian act as a Windows Domain Controller? I'm just curious because my boss recently tossed out some old servers and I grabbed them. They're good machines but I can't afford to pay $1000 for Server 2003 R2 just to setup a domain at my place and run Endpoint Protection and such. I've never used a domain setup in Linux before so I thought I'd ask and possibly try to, if Debian/Linux is capable of such a thing.
View 6 Replies
View Related
Mar 27, 2010
However, I have the problem I can't see any devices on my IDE port in my Asrock P43 mainboard, because the VIA VT6415 IDE controller isn't recognized. I typed an 'lspci -k', and I can clearly see there wasn't loaded any module to handle this VIA PATA controller.
...
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
Kernel driver in use: r8169
[code].....
View 2 Replies
View Related
Mar 31, 2011
I have been having trouble installing a working Debian 6.0.1a (Squeeze) desktop; I cannot seem to get Xwindoes working (under KDE). Is it possible that my video monitor is simply incompatible with Squeeze? I am using an old but not ancient Samsung SyncMaster 997DF with PS/2 keyboard and mouse. Output of lspci -nn | grep VGA is: 01:00.0 VGA compatible controller [0300]: Silicon Integrated Systems [SiS] 661/741/760 PCI/AGP or 662/761Gx PCIE VGA Display Adapter [1039:6330]
When I compared the contents of /usr/lib/xorg/modules and output of kdm.log between my working (but no longer trusted) Lenny and my nonworking Squeeze, I found that the driver sis_drv.so seems to be loaded by my Lenny but not by my Squeeze, and someone said that Squeeze uses a new version of Xorg which is incompatible with SIS. If so, does that mean that I need to get a new monitor? A new motherboard with video controller? I never had a video card--- do I need one to use Squeeze with KDE?....
View 8 Replies
View Related
