Ubuntu Networking :: Route Traffic From Wlan0 Through Eth0?
Dec 10, 2010
I'm running Linux Mint 10 . I have a wireless PCMCIA card (Linksys WPC 11 ver.3) that I've put into master mode, and I'm trying to set up my laptop as a wireless hotspot. I am very confident that I want to do this and have no interest in using a wireless router....I say that because that topic inevitably comes up with posts like this. The problem I'm having is I don't understand how to get wlan0 and eth0 to "talk" to each other...That is, I don't know how to set it up so that traffic from wlan0 goes through eth0, so that devices that connect to my hotspot can access the internet.I've seen a few guides about this, but they were either much broader in scope (i.e. much more complex), or for other distributions, etc, and it's too much for me to follow as a linux .
View 6 Replies
ADVERTISEMENT
Sep 29, 2010
I need to set up my centOS computer as a firewall in my home network. Ive got 2 interfaces, eth0 and eth1. I want to allow and forward all traffic on eth0 and block all traffic on eth1 except ssh, ping(icmp) and DNS. How do I do this? Ive tried some editing in /etc/sysconfig/iptables but no luck.
View 1 Replies
View Related
May 11, 2010
I've succesfullly connected to my vpn with kvpnc, but none of my traffic is going through the vpn! I dont know how to route traffic to the vpn. for instance, when I go to whatsmyip.com it still has my previous ip.
View 1 Replies
View Related
Jul 15, 2010
I have a wired connection going to my router, which is encrypted with WPA2-PSK. That works fine. I hooked up a WUSB54G v4 (Linksys USB Wireless Adapter), and used ndiswrapper to install the drivers from Vista to make it compatible with WPA2. Also configured the /etc/network/interfaces with the wpasupplicant lingo to make it all work. So if I do that, my eth0 will not work anymore. Also on a side note my network manager stops with displaying in the top panel. Not a problem I can run /etc/init.d/networking (re)start and dhclient eth0 (wlan0) and all the other commands that are necessary to make it work.
Back to the problem, so I hook up wlan0 with the settings and eth0 stops working. I want to use the wlan0 solely for the purpose of my media server. The eth0 is there for my internet and that is it .
How can I keep 'em separated?
View 6 Replies
View Related
Mar 23, 2011
I'm running Ubuntu Server 10.10 on a 64 bit laptop (also have GNOME installed just for convenience), and have a website up using apache2. I am wondering if it is possible to configure both eth0 and wlan0 to the same local static IP address? I would like to walk around my house and do stuff when I want and still have the website accessible, but also be able to jack my laptop back into the router when I am away, just for peace of mind.
Is this possible? If it is, do I need to do some configuring in apache2 to tell it to use another device? Is this even a smart way to get what I want done?
View 2 Replies
View Related
Sep 11, 2010
I just switched from Fedora 13 to openSUSE 11.3 on my laptop and so far love it...well...not quite. I'm having some major network issues. As in...no networks.
I installed everything and booted up for the first time. Everything worked great, I had wireless through wlan0 and could connect directly to my home router via eth0 with no problems. Installed a few applications and ran into some problems with hibernating/suspend modes. I rebooted and like magic, NetworkManager said networking was diabled. My WiFi light was off. Network switch on the computer didn't do anything.
I thought alright, I'll connect my ethernet cord and can go from there....problem is that won't work either. I tried searching for drivers online on my desktop, found some and transferred them via USB with no luck. They won't install. I have no idea why, or whats going on but I really need my laptop for school on Monday so it would be AWESOME to have it working by then.
Here is what I have:
Intel 5150 WiFi card
Dell Studio XPS M1640 laptop
OpenSUSE 11.3
View 1 Replies
View Related
Jul 23, 2011
just wondering if I could get a hand with bridging my eth0 and wlan0 connection. I'm using Ubuntu 11.04 if that helps at all.
View 1 Replies
View Related
Aug 15, 2010
I would like to pose is very specific to a system I'm assembling. I have ask for assistance from other forums and people, however the answers receive were too vague to implement.
As for my background, I am a network user able to write TCP Linux client/server applications quite easily. At a Linux system level I do not understand the necessary combination of applications and services to affect the following;
Network components;
- WiFi access point/router with four ethernet ports
- Laptop (user computer) cabled directly into the access point via a physical cable
- Second computer running Ubuntu 10.04, with one WiFi (wlan0) and one ethernet (eth0) interface. Eth0 is configured as a DHCP server with the following;
IPaddress 192.168.252.1
broadcast 255.255.255.0
Eth0 is physically connected to an IP camera via a Cross-over cable. The camera is configured as a DHCP client. This connection works perfectly from the Linux box with a KVM attached.
Wlan0 is connected wirelessly to the access point and the Laptop can access the Linux box and vice versa.
My objective is to have the
- Laptop via the access point/router connect directly to the IP camera on the Linux box via the wireless link.
- I would prefer not to make any configuration or routing changes/entries on the access point/router.
The type of response I'm looking for;
- is this possible at a macro level
- what facilities/server are required on the Linux box (I would like all configuration applied to this computer only)
- what commands need to be executed and in what order. If possible a brief explanation of why the command is needed and where it fits in the grand scheme of the solution.
This is probably a gigantic request outside what the forum usual activity.
View 1 Replies
View Related
Mar 4, 2010
My ISP has given me 3 IP addresses to use for the internet (76.148.200.3, 76.148.200.4 and 76.148.200.5).
If I do a "wget whatismyip.com" or netcat into another server, I am appearing as 76.148.200.3.How do I change my route (command line) in linux to route internet traffic through 76.148.200.5?
Code:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
code....
View 9 Replies
View Related
Mar 28, 2010
I have eth0 and tun0. tun0 is a VPN tunnel going over eth0. Everything on the other end is setup and working fine, when I type Code: traceroute 4.2.2.1 I see my the ping is going over 192.168.2.99 (eth0). When I then type Code: route add -net 4.2.2.1 netmask 255.255.255.255 dev tun0 traceroute 4.2.2.1 I see ping is going over 10.8.0.1 (tun0) instead of eth0, so that is working
What does not work however is when I do Code: route add -net 0.0.0.0 netmask 0.0.0.0 dev tun0 traceroute 4.2.2.1 I get no ping! I believe the problem is because all traffic is routing over tun0, which means even the VPN tun0 needs to go through eth0, it can no longer do this. Is there a way around this where I can route everything except for 114.77.31.26 (which is my VPN gateway for tun0)?
View 18 Replies
View Related
Mar 18, 2011
I just installed a fresh copy of debian (no GUI). I want all my traffic on bash (such as when I do ping or dig or wget, basically whatever) to be sent to localhost:8080. How can I do that? I've a ssh port forward setup that will forward all traffic arriving at my localhost:8080 to another server.
View 4 Replies
View Related
Jul 7, 2010
When I type ifconfig,
I see wlan0 and eth0. I want to somehow bind these two together into one device.
How would I go about doing this?
View 3 Replies
View Related
May 10, 2011
I am trying to set up a Linux box that can act as a router (and firewall later). I have a Debian 5 installation and it has two nics in it. I am trying to use the linux route command to set up a route between the two interfaces. I am finding it difficult to do. Let me explain how I am trying to set up my network: I have the ethernet cable from my modem connecting to eth0 of my Debian box, then I have eth1 connecting to a switch, which I connect all my computers and other devices to. I want to have two different ip address schemes for the devices. So here is my interfaces file:
Code:
#eth0 connects to modem
allow-hotplug eth0
iface eth0 inet static
[code]....
So I am wondering, to get my ethernet traffic from eth0 to eth1 and vice versa, do I need to make it so the Gateway for Destination 192.168.1.0 is 10.1.1.1, and for Destination 10.0.0.0, Gateway 192.168.1.0? I have looked at the linux manpage for route and I am still confused. I have also looked at the Debian networking page, but it is still unclear to me how to do this. how I am to use the route command to get this working? Or am I not even supposed to use the route command?
View 4 Replies
View Related
Feb 3, 2011
what i want to do is
client <--> wlan0 <--> computer <--> eth0 <--> internet
i have 2 network connections eth0 wired connected to internet wlan0 wireless (work fine) i have installed hostapd with madwifi and so on oki when i run hostapd the clients see the hot spot oki clients connect with wpa oki network manager run at demand not automatic (keep it for internet help) now i'm a bit lost what do i need is wlan0 give the client an ip (dhcp demand) create a bridge between wlan0 and eth0 steps to create a permanent bridge between wlan0 and eth0
View 2 Replies
View Related
Aug 21, 2010
I have a linux router with 2 physical ISPs and a VPN tunnel that all my traffic passes through. I would like to setup a rule to redirect all traffic from one internal IP address (10.0.0.x) through the physical link only. My current script is as follows.
iptables -F
iptables -X
echo 1 > /proc/sys/net/ipv4/ip_forward
[code]....
My goal is to do something similar to the mangle on the tor traffic, but for an entire host.
View 2 Replies
View Related
Mar 2, 2011
The task I am trying to complete is the virtualization of an IPv6 router created using two fedora machines. Here is the physical setup I have now...
PC1:eth0 <------> network
PC1:eth1 <------> PC2:eth0
PC1:eth2 <------> PC2:eth1
PC1 runs radvd to provide router advertisements to the network and a DHCPv6 server for stateful addresses.Each interface is configured on a separate subnet. PC2 runs a DNS server on eth0. PC2:eth1 is used as an IPv6 client for testing purposes. The connections from PC1 to PC2 are just crossover cables.I've created virtual machines of both PCs and have created 4 virtual adapters on the host machine for each of the local-only interfaces.Now I have this:
PC1:eth0 = HOST eth0
PC1:eth1 = HOST vboxnet0
PC1:eth2 = HOST vboxnet1
[code]....
View 2 Replies
View Related
May 7, 2011
My linux machine is connected to the outside internet, and I have a minecraft server running on an internal machine (192.168.1.201). Right now, I am forwarding port 80 on the linux machine to 192.168.1.30, which is working.
iptables -t nat -I PREROUTING -i eth0 -d 192.168.1.30 -j DNAT --to-destination 192.168.1.201
iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
iptables -A PREROUTING -t nat -i eth0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED,RELATED -j DNAT --to 192.168.1.201
______________________________
I want to filter out the GET/POST requests and forward them to port 8080. I can't seem to get that working.
I've tried this:
iptables -A INPUT -d 192.168.1.30 -p tcp --dport 80 -m string --algo bm --string 'GET' -j REDIRECT --to-ports 8080
View 1 Replies
View Related
Dec 9, 2010
Im setting up a server thats connected to a large network. Now my external ip on the network is static and is 10.0.12.15. What I want is to create a dhcp network using the second port of my box. The first port eth0 goes to my network with the static ip 10.0.12.15 and my second port is connected to a switch with the static ip 192.168.12.1. Now dhcp works fine but none of the boxes that are connected to the internal ip cannot connect to the internet. Iv tried using squid and manual static ip routes. Im not using network manager or anything cause its a command line server.
View 1 Replies
View Related
Apr 22, 2011
I am using Debian 5 and I have some networking experience, however I want to learn to do this the best way possible. I have a Debian box with two nics and I want to connect that to a switch and use my Debian box as a router basically, as well as having a firewall setup within that too.
Should I use iptables to set up nat or the route command or what? I just want to know the group of tools to use in order to set up my network. Network diagram: Internet <------> Debian Box <----> switch <----> hosts I found some guides but they are for linux 2.4 and i'm not sure if they are right.
View 1 Replies
View Related
Aug 21, 2010
I am attempting to run apache on my linux router while connected to a VPN. My default route is set to the VPN endpoint and I cannot control port forwarding at that end. I cannot seem to connect to any service that i bind to the eth0 interface. I believe that my iptables rules and OpenVPN are the source of the problem.
/sbin/iptables -t nat -A POSTROUTING -o tun1 -j MASQUERADE
/sbin/iptables -A FORWARD -i tun1 -o eth1 -m state --state RELATED,ESTABLISHED -j ACCEPT
/sbin/iptables -A FORWARD -i eth1 -o tun1 -j ACCEPT
View 5 Replies
View Related
Jan 18, 2010
I want to add this route but I am getting this error message. What is the reason of this problem? I cant add this route? how can i add?
Code: [root@linux/]# route add -net 10.1.0.0 netmask 255.255.0.0 gw 10.2.0.1 eth0 SIOCADDRT: Network is unreachable
View 11 Replies
View Related
Nov 21, 2010
My Ubuntu Box has 3 interfaces. eth0 (Internal 192.168.1.0/24)eth1 (External ISP DHCP)eth2 (External ISP Static IP)I need the outgoing traffic to internet for 1 of the internal pc (192.168.1.10) to only go only go through eth2
View 4 Replies
View Related
Nov 13, 2010
I have a couple of interfaces in a Fedora 14 box:
eth0: internet provided by an adsl router
eth1: LAN
I set up system-config-firewall to masquerade all outgoing traffic in eth0, as I did in other Fedora 13 boxes, but it seems it doesn't work. It sets to 1 /proc/sys/net/ipv4/ip_forward and also set the appropriate rules in iptables. But all traffic is blocked from the LAN to the Internet. "ping www.google.com" works in the Fedora box, but doesn't work in the LAN computers using the F14 IP as gateway. I have another F13 computer elsewhere configured this way and it works fine. But this one has Fedora 14.
View 2 Replies
View Related
Oct 18, 2010
I'm having a problem and despite I have googled a lot cant find the root cause. I have a server with two embedded NICs and centos 5.5 loaded. I need to have one NIC with a fix internal IP address to communicate with the intranet and a second NIC with a fix address from my telephone provider. I know I cant have two different gateways on the net so I configured only the gateway for the second NIC leaving the field empty for the first.
I found that the first NIC is handling all the traffic for both interfaces (eth0 and eth1) and the second NIC is in standby (or doing nothing). This is causing the traffic intended for the second NIC never reach their destination. After a couple days working with the BIOS and other configuration files I tried another way of solve the issue. I put a fix address for the first NIC and another fix address for the second NIC (both in the same subnet) and from a computer pinged successfully both addresses. However if I disconnect the cable for the first NIC both interfaces goes down (eth0 and eth1) and both pings fails. If I disconnect the cable for the second NIC (with the first one connected) both pings still running without any disturbance.
I worked also in a second server with different hardware (different kind of motherboard, different NIC manufacturer, etc.) but the problem is also present in this second server. I was reading about NIC bonding or teaming, but this configuration is not present in the modprobe.conf or in the ifcfg-eth0 files, so I believe the problem is not related with this feature. Do you know what is happening with the NICs and how can I get two really, fully independent NICs?
View 7 Replies
View Related
Mar 4, 2011
I need to setup two ethernets in my Centos box. OK no problem both ethernet and 1 virtual works perfect. eth0, eth1 and eth1:0. I'm trying to set up diferent routes for eth0 and eth1/eth1:0 I need eth0 has a 192.168.1.1 gateway and eth1/eth1:0 192.168.1.100 gateway.I think I've tried almost every thing but always get one gateway for all the eth.These are my config..
/sbin/ifconfig
eth0 Link encap:Ethernet HWaddr 00:XX:XX:XX:XX:XX
inet addr:192.168.1.168 Bcast:192.168.1.255 Mask:255.255.255.0[code]......
View 7 Replies
View Related
Aug 12, 2011
On a new Dell Lattitude e6400, I have installed both arch and Ubuntu. Ubuntu recognized wifi and ethernet right away and connected and is working fine, but in arch, I am having more problems then I usually do when using arch. From the output of lspci the ethernet is a intel device 1502, I have researched this and found it to need the e1000e module as its driver. I modprobed this module sucessfully, but no ethernet. With wlan, i have found that the card is a DW1501 Wireless-N WLAN Half-Mini Card that has a broadcom 4727 chip in it. I downloaded the windows driver for this chip and isntalled it with ndiswrapper but this did not help. What I think is the root of the problem is the error message that restarting networking creates.
Quote:
Dell only supplies drivers for ubuntu, but it should still be possible to get this to work. I have tried booting various live distros that I had drives for and I found that the parted magic boot disk saw the ethernet port and was able to connect to ethernet, and that the ubuntu live disk was able to connect to both wifi and ethernet. Somehow they must be seeing the prescense of the hardware in a way that I have not tried with arch. Please help, I really need to get this computer workign with arch.
View 1 Replies
View Related
Mar 22, 2011
I am running Ubuntu Server 10.10. I have installed OpenVPN using this guide I have set up everything correctly as this guide says, but I am having problems with the config file. I want to securely route all traffic on the client to the server, how ever the server will not start. My config is below:
Quote:
#################################################
# Sample OpenVPN 2.0 config file for #
# multi-client server. #
# #
# This file is for the server side #
[Code]......
The servers ip is 10.0.0.65 and I want to assign the clients the ip range of 10.0.0.200 to 10.0.0.20 When I try to start the server I get the message Fail.
View 8 Replies
View Related
Apr 22, 2011
I have an Ubuntu server box with multiple NICs. I'd like to specify that all traffic bound for a certain IP range goes through one NIC, and everything else goes through the other. Does anyone know how to do that? I'm not a total newbie, but I'm also not a linux guru (but usually can google my way to a solution...usually).
ETA: Source and destination IP for routing.We have 1 NIC with a public IP, all public IP's should talk to it.Another NIC with a private IP, all private traffic should talk to this.In practice, I have some devices on a different subnet of the public IP range we have that will only talk to the private IP.
View 2 Replies
View Related
May 24, 2010
Is there a way to get conky to show only eth0 or wlan0? My configuration only shows the wireless bit when wifi is switched on but shows eth0 all the time.
Temperature: I have nvidia card with drivers from rpm fusion, can conky give me the temperature of the card and the cpu?
View 6 Replies
View Related
Jun 25, 2010
In an attempt to set up wireless so I could connect to the university network, which I think I probably should have just downloaded network manager or something but I didn't, I tried to put things in /etc/conf.d/net and some other places and I am afraid I'm not sure exactly what (and I have learned my lesson! I will pay attention to what I am doing so I can undo it next time I mess around with stuff!)
Anyway, the long and the short of it is now, when the computer is starting up and its doing the init stuff net.lo doesn't start. Later try and start net.lo or net.eth0 you get told "not enough arguments"
View 3 Replies
View Related
