I've connected my openSUSE laptop with a Windows XP computer using an Ethernet cable that supports two-way traffic.
LAN settings on Windows XP
IP address: 192.168.5.1
Netmask: 255.255.255.0
Gateway and first DNS server: 192.168.5.2
LAN settings on openSUSE
I was trying to activate my wireless connection .... in turn did something that triggered eth0 no-carrier when "ifstatus eth0"
View 2 Replies View RelatedToday I switched from Ubuntu to OpenSuse. But I can't setup my Ethernet connection.I have 2 PCs connected with a crossover cable, one with Ubuntu, the other with OpenSuse 11.3. Lights are on in both NICs.
View 9 Replies View RelatedI installed 10.3 (after buying it a couple of years ago and letting sit on the shelf) and can't get it to configure my ethernet connection or my wireless card. Yast doesn't include a list of available cards, and the error I get in installation-network setup is that the kernel isn't present. The machine I'm installing this on is a Lenovo, in which there isn't a discrete ethernet card (it's in the motherboard), but my wireless card (a Cisco LINKSYS 802.11G) is a discrete card. Because I'm divorcing Microsoft for a number of valid reasons, I don't have Windows available on that box.
View 4 Replies View Relatedguide me to connect the SLED 11 SP1 to KEVIN.org (This is the name of my domain I created) Wich i created on windows server 2008.
View 9 Replies View RelatedI'm on opensuse 11.4 (11.3 won't work with my monitor).
My computer gets internet through wireless and I want to share that internet through its ethernet port. So far I've tried using Knetworkmanager to create a network bridge between my wireless and wired connections. I created a new wired connection and shared it using the ip address settings. I was able to get both connections active, but the device hooked up via ethernet had no internet connectivity.
I also tried this command:
echo 1 > /proc/sys/net/ipv4/ip_forward
but another test resulted in the same fashion (no internet on wired). I believe anything I add to /proc should have an immediate effect, correct?
I often use an Ethernet cable to connect my computer to another computer for various purposes. But when I do that, I cannot use the internet even though I'm still connected to a WiFi access point. I'm presuming that's because openSUSE is trying to reach the internet through the Ethernet cable, which has precedence over WiFi.Is there a way to enable internet usage via WiFi while I'm connected to another computer over Ethernet?
View 9 Replies View RelatedI have just switched over from Ubuntu. My PC with Ubuntu connected to the ethernet fine, but now the internet is not found at all. Can someone tell me what sort of things I need to do to get my internet up?
View 2 Replies View RelatedI am using Sony vaio E series laptop. Previously, I was using my E63 nokia phone as modem for internet connection and i have installed K-internet in my Opensuse OS, and configured wvdial.conf as follows:
[Dialer Defaults]
Init1=ATZ
Init2=ATQ V1 E1 S0=0 &C1 &D2 + FCLASS=0
Init3=AT + CGDCONT=1, "IP","bsnlnet","",0,0
Baud=4608000
Modem Type= Analog Modem
[Code]....
But now, I have Reliance Brodband Connection through LAN. when I am Pluggin in my LAN cable in my laptop YAST Network Configuration Showing Marvell Ethrtnrt is not Configured, When i am going to configured that part it's showning me no Enther net present or Configured By ny Hardware Is detecting ethernet. So, I have concluded that it might be the problem with my wvdial.conf. Also, additional information are as follows:- S- Open suse 64bit, Version- 11.2, cause I cannot Connect to my Internet now? What should I do to have this Problem Fixed?
I've been searching for a couple of hours and have not found any threads that solve my situation... hope I'm not repeating something here.
Setup: Notebook with openSUSE 11.2 using KDE 4. Using Network Manager to manage network connection (although I've tried configuring this using ifup as well with no luck).
I need to be able to connect to client networks via a network cable (Ethernet) and connect to the internet via my MiFi 2200 Mobile WiFi. Both cards/connections are active with the following:
I have no problem mounting drives from the client's network. But, can not reach the internet. If I disconnect the ethernet cable, the browser will immediately connect to the internet and load web pages.
I'm assuming the ethernet connection is taking precedence over the wireless connection?
I can't imagine that there is not a way to set this up. If Windows can do it, I'm sure openSUSE can!
system:
destop
openSUSE 11.4 KDE
single wired network connection
running as a headless server
upgrade from 11.1
Problem: I had a bunch network services running under 11.1 with KDE. Now after upgrade to 11.4 full network functionality is broken. I was using ifup but now is broken. Between ifup and NetworkManager I can demonstrate the full required range of functionality but not all at the same time (the union of functionality of each provides the full required functionality, but not individually). WOL does work in all cases.
With 'ifup', it seems that everything is 'working' as before, but services are broken when accessed from outside. eth0 up and fuctioning with statically assigned IP. Outgoing connections seem to work - I can browse the web. But trying to access services from outside is broken. VNC is rejected. Connecting to SMB shares reports login error. TFTP doesn't respond. SSH connection is rejected.
Although sometimes it will get in a state that everything except VNC works (connects but then is dropped upon login with "Error while waiting for server message") but I can't consistently reproduce this state other than it seems to happen after some extended period of time.
I have verified the firewall is off and apparmour is off.
On the other hand, everything works with 'NetManager' (both KDE and Plasmoid) with no other changes. The problem here is that it does not seem possible to set a static IP address - eth0 doesn't show up in the list of wired interfaces to be able to select and edit. That's problem 1 - I need a static IP. (I suppose I could reserve an address at the DHCP server, but a static IP works 100% to get the right address). The other problem is that neither NetManager starts at boot and only start _after_ login at the console - that won't work as I never log in at the console. (I suppose I could set it up to login automatically into a console or something but I would rather not)
im on node1 when i type the command ssh node2@ip the terminal hangs up a bit then an error message stating that connection timeout but here is a thing: i cant ping to node2
but i can terminate the ping manually using ctrl+c when i terminate the ping usual message appears stating 10 packets transmitted, 100% loss
ps: when i go to node3 and ssh to node2 it works fine and also i can ping from node3 to node2 very fine. and the firewalls are down at all nodes -all wired connection over a switch
I can make a connection to the vpn server, the connection starts, but nothing happens! My IP address remains the same as previous! There is nothing added to my Knetworkmanager, I'm a beginner I should use a pcf file for my vpn connection. I use it properly, I'm sure because the connection starts and an icon is added to my panel and remains until I disconnect.
I checked it via ifconfig -a, the last part (which is for vpn) is:
Code:
tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:141.213.169.76 P-t-P:141.213.169.76 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1390 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
I installed the OpenSUSE 11 on my IBM T43 laptop. After installation finish I found the Yast can't detect the integrated ethernet cardBroadcomCorporationNetXtremeBCM5751MGigabitEthernet PCI Express(rev 11).
View 5 Replies View RelatedHow can I enable the network with Networkmanager WIHTOUT logging in in OpenSuse 11.2?
If I define a connection for ethernet the System connection is greyed out. I want to use Networkmanager because I have also wireless connections...
My WiFi can connect to internet without any problem, until I plug my ethernet cable ...then I lose internet.
So the question is : how do I configure my ip/dns and stuff to still have internet when I'm plugged by cable at the same time! it was working on windows ;-)
I'm currently using SuSE 11.4 and after running the full online updates and restarting the machine as YAST suggested, I no longer have eth0/eth1 available.
I'm clueless about what to do since I'm kinda new to Linux and at the moment, I'm trying out all the distros before making a full commitment to anyone. So far, Ubuntu has been trouble-free from day one, but I'm willing to give this distro (opensuse) some slack.
I have a strange problem. An old PC is my home server. On the PC I had in the long past 2 NICs. For the last year or so, I had only one NIC installed, a Compex with 8139too module which run just fine. After the upgrade to 11.4, 32bit of course, with zypper dup, I saw that I had no internet and no network connection to the server. So, I logged on the server and found that rcnetwork could not start the eth0 and eth3(!). OK, a mistake I thought. Enter Yast and solve it. Unfortunately, yast reports 2 cards! I removed all of them, rebooted but nothing. lspci reports 2 cards, while I have NONE installed on the motherboard!hwinfo --netcard the same! yast the same! So, the OS "knows" that I have 2 NICs, while I definitely have none!
Checked if /etc/udev/rules.d/70- had any left data from the past, but the file was empty. Checked the /etc/sysconfig/network/scripts nothing again.In principle, the openSUSE 11.4 believes that I have 2 cards (and with wrong MACs, obviously) and I cannot make it rescan the PCI bus to find that I have nothing! I am sure that some garbages are left somewhere but I don't know where to look at. it is very critical to have that server but on-line and in my LAN.
I would like to have all traffic from the ethernet connection out through the wireless (basically using the box as a router) however I am having some trouble doing this.
I have done this before on Windows however I am having some trouble doing this on linux, I have tried using Squid Proxy however I am having some trouble using configuring/using it.
I am using Yellow Dog Linux however I am willing to change to any other distro as long as it is compatable with PS3 (as this is what im using linux on)
I'm new to this environment. I'm currently using OpenSuse 11.2 freshly installed. I'm attempting to install FCoE as a target on one box and an initiator on another. I've gone to the Open-FCoE.org site and got the tar file open-fcoe-2.6.34.tar.gz and attempted to install it, but there appear to be missing dependencies, such as libhbalinux. However, the more I seem to install, the more there are unresolved dependancies. I've followed the Open_FCoE Target and Iniator Quick Starts, but I'm running into many missing souce dependencies. What exactly I need in the way of packages, files, etc and how to install them? Is there any documentation of how to install FCoE from scratch?
View 2 Replies View RelatedAfter updating to openSUSE 11.3, and restarting my computer, I placed my computer in sleep(suspend to RAM) mode, and I lost my internet connectivity. I noticed that my computer was only connected through ethernet. After entering "dhclient eth0" in a terminal, I received the following output.
Code:
RTNETLINK answers: Cannot allocate memory
This is the first time that I have had issues with connecting to the Internet using Ethernet.
I have a hp zd 7000, i really like this laptop, the onboard ethernet will not work at all. i purchased a dynex wired ethernet pcmcia card to get on the internet with. i have had no luck getting on the internet with it it will light up so i am getting power but no transmitting light works at all i have three net work cards listed in the system. one is the wireless. and the other two are the wired eth0 is the onboard and eth2 is the dynex what can i do next to determine the problem i do not use the wireless at all.
View 1 Replies View RelatedI have a Opensuse 11.4 workstation that has two ethernet ports and I was wondering if there is the chance to use the other ethernet port as a switch to a Mac/PC?
View 2 Replies View Relatedi have installed openSUSE 11.2 on a dell dimension 2400. My Ethernet card wasn't working, so i am using a wireless interface, but it doesn't work either. It worked on a dell dimension 4400, but when it gets to the activate network my system freezes. Should i re-install my system, or should i post this under the hardware category.
View 9 Replies View RelatedWhat must be done to mount an ext3 partition that's on another computer which is connected via utp crossover cable? I can't seem to figure this one out, though I've read somewhere that it can be done, and I'd like to know how.
View 2 Replies View RelatedI did a fresh install of OpenSuSE 11.3 KDE 64-bit on my new laptop. Worked like a charm. But I brought it with me to work without connecting it to a wi-fi and now the network manager doesn't want to start when I'm back in range of my home connection. Also, whenever I try to launch KNetworkManager, it won't load up a window and I still can't connect. This is even disabling the Ethernet port also.
View 3 Replies View RelatedI've not found how to configure more than one ip address with network manager.Nor with kde nor with plasmoid network manager.I need several virtual ip addresses for eth0 when the "default" of eth0 is connected i.e. "Connected to Auto eth0" should initialize the virtual interfaces.I have not found no even how to configure the ip address.I think this will be used from ifup config in yast or not?There I have the virtual interfaces but they are not taken from network manager.And last but no least: Is it possible that when using network manager the eth0 is enabled even no user has logged in?
View 4 Replies View RelatedI deleted the firewall files "K09SuSEfirewall2_init", "K01SuSEfirewall2_setup", "S11SuSEfirewall2_setup" and "S01SuSEfirewall2_init" from "/etc/rc.d/rc5.d" in order to disable the firewall when rebooting.
As a consequence all network services are not working. I can't connect to any other machine nor to the internet.
I rebuilt the symbolic files based on the ones for runlevel 3, but still no network services are available.
Any suggestions how to make it work again? I'm using Suse 11.3.
I have a dual boot system (Suse 10.0 and Windows XP Pro) in my notebook. My notebook is toshiba m358, which has a Marvell Yukon Gigabit Ethernet Network Card (Marvell 88E8072) on it. My problem is this: in Windows XP Pro, the network card works well, but in openSUSE, the light on the network card does not turn on. I believe that there is no driver for the network card. I have tried several ways to solve this problem:
1. Download Marvell 88E8072's driver from "[URL]", whose name is "install_v10.85.3.3.tar.bz2", and then install it with following commands:
Code:
# tar xfvj install_v10.85.3.3.tar.bz2
# cd DriverInstall
# ./install.sh .....
Code:
# modprobe sk98lin
# WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/.
After I reboot the openSUSE, the light of network card is still off.
2. Follow "[URL]" to configure the Marvell 88E8072. It also does not work.
Just today I installed opensuse 11.3 on my Compaq CQ61. Even though I am able to connect to networks (both with an ethernet cable and wireless) I don't have internet access. I have used opensuse for a very brief period in the past and I had no such problem.
View 3 Replies View Related