OpenSUSE Network :: 11.3 Amd64 - Having Internet Access But Cannot Access Repos - IPV6?

Aug 26, 2010

I installed 11.3amd64 as a VM under Vista/VMWare Player - all worked fine. I have now installed it as a physical system. It nstalled cleanly BUT during first boot it could not access the repos. With each repo it gave the message

- download (curl) error for (repo)
- error code connection failed
- error message could not resolve host (repo)

This was followed by a message box containing

- UI syntax error
- no widget with ID 'contents

Firefox could not access the internet (cannot find server) until I disabled IPV6 (I used about:config), now it works fine. I think the repos problem is because of IPV6 - I usually have trouble with IPV6. I tried disabling IPV6 with the following (How To Disable ipv6 on SuSE Linux | Linux Poison)

[code]......

View 8 Replies


ADVERTISEMENT

OpenSUSE Network :: Cannot Access Community Repos List

Sep 11, 2010

Having assorted problems accessing v11.3 update repositories. The issue appears to be either with IPv6 or my ancient 2Wire 1000SW router.

Last week, I replaced Ubuntu with openSUSE on this Dell laptop. When I couldn't access repositories initially, I turned off IPv6 in YaST, with no luck. Turning off IPv6 in Firefox did allow me to see opensuse.org and other otherwise unavailable sites.

I edited my primary/default repo list in YaST with IP addresses replacing DNS names with great success -- except for the non-OSS repo, which YaST couldn't find. Anyway, I had a successful update!

Now adding repos to the default set is the problem. When going to Add > Community Repositories, I get the "Unable to download list of repositories or no repositories defined" message. Trying to add Packman.unixheads.com either with named URL or with IP address doesn't work either (it was curious that when using the IP address, YaST still says it can't find Packman.unixheads.com).

When I read that Packman was converting all its servers to IPv6, just for grins I went back to YaST and Enabled IPv6 again. After a reboot, I tried adding Packman again. No luck, but suddenly editing the default openSUSE non-oss repo and entering the IP address WORKED!

One more data point: I tried using a few 1-click installations from the collection at opensuse-community.org. Most failed, but for some reason, I could add the NVIDIA repository!

While I think the simple solution is probably replacing the router I've had since 2004, I'd like to avoid that particular expense right now. I'll note that I never had a problem accessing (K)Ubuntu repositories.

I'm wondering if there's a zypper or YaST config file I can edit that might allow access to the Community Repo list (though the Packman experience is somewhat discouraging in that regard). Is there something weird going on with MirrorBrain too? Figuring out how to handle IPv6 might be relevant here too.

View 2 Replies View Related

Debian :: No Access To The Internet And Cannot Update Repos

Apr 10, 2011

In the live CD, auto eth0 worked fine.After installation, it cannot connect.I am using vaio laptop VPCCW16FG, there is a known display bug therefore i am booting into the OS with 'nomodeset'.i have no access to the internet and cannot update repos, therefore i cannot work around the bug.

View 3 Replies View Related

OpenSUSE Network :: OS 11.2: Cannot Now Access Internet

Feb 4, 2010

Is there a network trouble shooting guide for OS 11.2 that I could follow? I've shot myself in the foot so I should try to fix it.

I changed the DNS server addresses and the number of IP addresses on my router. I then set my Linux system to use static IP addressing and edited the network settings for my network adapter accordingly. I can now no longer get to any web-site.

By contrast, I also updated 1 of my Windows computers in a similar way; it continues to work without problem.

View 4 Replies View Related

OpenSUSE Network :: No Internet Access 11.2

Feb 17, 2010

I am trying to get internet connection on Open Suse 11.2 through my wireless connection. I can connect to my network but there is no internet connection. The internet connection does work with other Linux distros and with Windows 7 laptop and Windows XP machines. I tried turning off the firewall but still no connection. What is even stranger is I can ping Google but in Firefox I cannot go to Google.

View 1 Replies View Related

OpenSUSE Network :: Can't Get Internet Access?

Dec 4, 2010

I'm kinda new to this, and usually i get help from a computor technician at school. BUT sins its Saturday, i cant get any help, and i realy need it. Well my problem is that i cant get any internet access using eth0 at my computer. I dont know what i have done wrong, if i have done anything wrong, it just reinstalled. ANd i dont know how to config it.

View 3 Replies View Related

General :: Use Ipv6 To Access Website While Only Ipv4 Is Supported In Network?

Feb 6, 2011

I'm using Ubuntu Linux as my operating system.In my network only the ipv4 is suported, and I need to access some website through ipv6. How can I do it, is there a way to tunnel from the ipv4 to ipv6.

View 2 Replies View Related

OpenSUSE Network :: Two Network Cards With Different Settings For Internet Access

Feb 9, 2010

I have a desktop computer running OpenSUSE 11.2 with two network cards installed. I would like to use both cards for connecting to the internet using different networks. The setting would be the following: eth0 is the main (default) card, almost all programs should use this NIC for connecting to the internet. eth1 is used only by a few programs, which have setting for selecting which network interface to use. The two NIC's are connected to different networks, so the IP address of the NIC's, the related subnet masks and gateways are also different.

Saying short, I would like to have the two NIC's as they would be in two separate computers. I can set the IP address and subnet mask of the NIC's. The main problem is that I can only declare one gateway. How can i setup this? I do not use network manager, I configure network cards using yast, but if needed I can of course use ifconfig directly.

View 9 Replies View Related

OpenSUSE Network :: Network / DNS - Can't Access Any Internet Resources Or Router

Jul 30, 2010

I'm having a strange problem with my network connection/DNS. I turn computer the on and it recognizes and connects to wireless or wired but I can't access any Internet resources or my router. If I ping the default gateway, I get no response and I get DNS errors from any network services that run at start up. If I stop and start the network daemon then it all works fine until the next time I turn on my laptop. It does this for both wireless and wired connection.

I've tried to edit the network interface information in YaST but it says that configuration is handled by knetworkmanager and I have no idea where that information is accessed. I should point out that it all worked fine until I tried to connect to open WAP at my school and couldn't so I connected to the wired network. Next morning I had this problem when connecting to my home network. My questions are 1. What could be the cause of this error and 2. where does one configure the network interfaces when using knetworkmanager

View 4 Replies View Related

OpenSUSE Network :: Can Not Access The Internet Or The Router

Sep 14, 2010

OpenSUSE 11.3 x64 KDE I dont know what happened it is a new install thats been running for 2 weeks . Now for some reason I can not access the internet or the router. Samba is working with Dolphin I can browse shares on local network both Windblows and Linux and ping local IP's. But I can NOT ping my router (the default gateway IP) with this box or access it with firefox so no internet. A VirtualBox of XP Pro running on this box has no problems with its bridged adapter getting out and seeing the router. I disabled the firewall, added gateway IP to network settings, disabled ipv 6 from the get go, added service provider dns's to nameservers tried opendns servers also.

View 3 Replies View Related

OpenSUSE Network :: Can't Access Internet Through Wlan?

Apr 6, 2011

Brand new to the OpenSuse project. I'm have an old AMD Duron running 11.3 and I am having no luck in connecting to the www. I'm using a D-Link usb wireless adapter. I seem to have an IP address for the PC. here is the print from ifconfig:

wlan0 Link encap:Ethernet HWaddr 00:12:0E:45:75:F5
inet addr:192.168.2.7 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::218:eff:fec45:75f5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:246 errors:0 dropped:0 overruns:0 frame:0

[Code]...

View 3 Replies View Related

OpenSUSE Network :: No Internet Access After Upgrade?

May 11, 2011

I just did a large patch on my opensuse11.3 system (upgrade of all installed packages), and whilst my network interface works, I cannot get past my router onto the internet.

I can connect to other computers on my network (here at home), I have an IP address via dhcp from my router, but I cannot get internet access, either from thunderbird, firefox, or simply by [URL] Clearly the computer was connected to the internet just fine minutes before since I did the large patch! Also, my other computers CAN still connect to the internet.

how i can debug it? It is just too coincidental I have upgraded everything and now somethings amiss!

If it's relevant, my router is a netgear WGR614v9.

A few things I've tried...

Code:
linuxthinkpad:/var/log # /sbin/route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.1.0 * 255.255.255.0 U 0 0 0 eth1
link-local * 255.255.0.0 U 0 0 0 eth1
loopback * 255.0.0.0 U 0 0 0 lo

[Code]....

View 3 Replies View Related

OpenSUSE Network :: Wlan Working, No Internet Access?

Jan 23, 2010

recently ran into a problem with my internet access. Im using open suse 11.2 on a Dell Vostro 1520 laptop. I managed to get my wlan running and i can use firefox to access my router. In my router the laptop is also showing as connnected, dhcp reserved an ip for it.However if i try to browse the internet, no page is loading, actually no software that needs access to the web is working.

View 3 Replies View Related

OpenSUSE Network :: Cannot Access Internet After Update 11.3 X86_64

Nov 7, 2010

i've installed opensuse 11.3 x86_64 and everything works great. after install updates and restart i cannot access internet from wireless connection. Knetworkmanager says it is connected, i have a dhcp ip, gateway, and cannot access internet.... i tried to configure from yast and cannot access internet...

View 3 Replies View Related

OpenSUSE Network :: PPPoE - Cannot Access LAN And Internet Simultaneously

Feb 7, 2011

I need to implement at my sister this kind of connection: She is connected on Local area network that has about 50-80 pc's, but for internet access she must start an pppoe connection. For now when she wants to use lan she must put her local address (ps: they dont have dhcp), for pppoe she uses dhcp. Problem is that on that way she can't access lan and internet at the same time. She must disconnect from lan and then start pppoe connection and vice versa. I'm intrested if it is possible to have lan access at the same time as internet access. some kind of tunel through lan up to isp. I was googling little and so PPPoE tunneling. Is it that what I need here?

View 9 Replies View Related

OpenSUSE Network :: Firefox - No Or Extremely Limited Internet Access

Nov 15, 2009

I've been running Suse 11.2 KDE on a 64-bit Dell Studio 1535 since last week's release, and have had no trouble using Firefox. At some point today, however, it stopped accessing webpages -- or, when managing to grab a page, it would do so without full html rendering. 95% of the time I get an error splash, while the other 5% I get some sort of truncated page that looks nothing like it should. Konquer and Opera work fine, as does KMail.

I tried deleting the profile.int file (no luck), then uninstalled/re-installed (no luck), then uninstalled and deleted every Mozilla/Firefox file I could find in order for a fresh install -- but this has not worked after several attempts. I still cannot get Internet access. How to completely wipe-out Firefox in order to allow for a totally new installation?

View 9 Replies View Related

OpenSUSE Network :: Internet Access Lost After Upgrade / Get That Back?

Apr 6, 2010

I just upgraded from Suse 10.x to 11.2. Unfortunately, I didn't use 10.2 much and I('m a bit overwhelmed by the upgrade. Any advise is greatly appreciated.

After my upgrade, I lost Internet access. I don't really know my way around too well, but I did try to ping my router, but had no success. (Although I can ping 127.0.0.1).

I'm guessing that this means network access is not configured, although it looks OK to me.

View 8 Replies View Related

OpenSUSE Network :: Cannot Access NTFS Drives And Connect To The Internet Through LAN

Aug 20, 2010

Recently i started going into OSes other than Windows. So, i installed openSUSE 11.3 32bit on my system in dual boot with Windows7 32bit. Everything was okay But i couldn't find any drivers for my laptop. My problems are :

1. cannot access NTFS drives.
2. cannot connect to the internet through LAN
3. cannot connect to the internet through Wireless.

Computer's Configuration :
Dell Inspiron 14r
Intel Corei3 processor
Both the operating systems run fine otherwise

View 9 Replies View Related

OpenSUSE Network :: Wireless AP Configuration - Doesn't Have Internet Access

Aug 7, 2011

I'm trying to setup a wireless AP with my old asus eeepc, so it can act as a repeater to connect my android device on the other end of the apartment. I've already created the Wireless Access Point using hostapd. It took very little configuring, just changed from mode 'a' to 'g' and changed the channel from 60 to 1 and It was all set. Next I setup a dhcp server. Also simple enough using yast.

Up to this point, I was able to connect my android device to the newly created wireless network. However It doesn't have internet access. I guess I have to configure iptables for this, but I find it incredibly confusing! Here are a few specs to help with any examples: The laptop is connected to the internet through eth0 with IP 192.168.2.120 Hostapd is using wlan0, and I'm pretty sure it created mon.wlan0 So, to sum up, when I connect my android device to the network I can, for instance, see what ever pages apache is currently serving on the laptop, but can't access the internet.

View 1 Replies View Related

OpenSUSE Network :: Monitor Which Programs Are Allowed To Access The Internet And Limit Traffic

Nov 8, 2010

I would like to be able to monitor which programs are allowed to access the internet, but a search for programs to do this has turned up nothing. Preferably, I would like a notification to come up every time an application uses the internet. Is there any (n00b friendly) software available to do that?

View 2 Replies View Related

OpenSUSE Network :: Able To Connect To Networks (both With An Ethernet Cable And Wireless) Don't Have Internet Access?

Mar 2, 2011

Just today I installed opensuse 11.3 on my Compaq CQ61. Even though I am able to connect to networks (both with an ethernet cable and wireless) I don't have internet access. I have used opensuse for a very brief period in the past and I had no such problem.

View 3 Replies View Related

General :: PPPOE Server Access Internet Clients Fail To Access Internet

Aug 26, 2010

I have a linux box (fedora) with two ethernet cards eth1 and eth2. On eth1 I successfully configured a PPPOE internet connection. Such that from the server I can browse the internet. On eth2 I wired it to a wireless router essentially to provide the wireless cloud. On eth2 I also configured dhcp, such that the Linux box is both PPPOE and DHCP server.However my clients on the LAN cannot access the Internet.

On passing the routing command I get
Destination Gateway Iface
196.44.x.y 0.0.0.0 ppp0
192.168.1.0 0.0.0.0 eth2 (my subnet)
0.0.0.0 0.0.0.0 ppp0.

The router (functioning as a wireless access point mainly) has a fixed IP address of 192.168.1.2 and eth2 has IP address 192.168.1.1. The dhcp file running on Linux has been set with option router (Gateway) 192.168.1.1. I cannot figure out how to correctly set the routing table such that my clients on wireless can access the internet cloud. I googled and googled but no solid solution. Any suggestions?

View 3 Replies View Related

Ubuntu Networking :: The Phone Can Access The Internet Through The Computer Unable To Get Access To Https Sites, Like Webmails

Dec 31, 2010

I managed to configure my W890i phone to get access to internet through an ubuntu-based computer. It's very easy to use the phone to give internet access to the computer, but the opposite is quite more tricky. For that I've done the following

----On the phone---

-Set the USB network option to "through computer", so that the phone uses the computer's internet connection and not the opposite.

-Decide and set "Shared Network" parameters: user, pasword and workgroup.

-In "conectivity-> internet connection" set "allow local network" to "yes"

----On Ubuntu 10.04---

-Install samba, samba-client, smbfs, smbclient, firestarter and dhcp3-server

-Configure Samba (System-> Administration-> Shared folders): same workgroup as in the phone, add new user (the phone), passwd this new user. In my case the user was called "w890i" and the password given was the same.

-Once the phone is connected to the computer through USB (then select "phone mode"), a new connection appears in NetworkManager: usb0.The aim is to create a shared network that gives internet access to this device. Edit the IPv4 parameters of this new connection, set them to Manual and give an IP adress (192.168.0.1) and a subnet mask (255.255.255.0); the rest of the fields are left empty.Connect this network.

-Set firestarter to use dhcp3: sudo ln -sf /etc/init.d/dhcp3-server /etc/init.d/dhcpd

-Launch firestarter and follow the wizard. Set "allow internet shared connection", choose the device for the primary internet access, and then the device for the shared network (usb0). Then change the settings for firestarter: activate DHCP for local network, set IP to the one we gave before (192.168.0.1).

-Open dhcp3-server config file sudo gedit /etc/default/dhcp3-server And set INTERFACES="usb0"

-Set the policies of firestarter: in incoming connections, allow connections from the IP adress given to the phone (192.168.0.1). Then add rules for the ports that need to be open for this connection. I opened HTTP, HTTPS, SMB, SMTP, POP3, IMAP, IMAPS, DHCP for all the connections in the local network.

-Apply policies and start the firewall.

------------

After all this, the phone can access the internet through the computer. Two problems appeared:

1. I couldn't get access to https sites, like webmails. The phone gave a "communication error". But then I tried with Opera instead of the browser built in the phone's firmware, and I could finally get to https sites.

2. I couldn't retrieve mail, neither POP nor IMAP nor IMAPS. I thought it was a firmware problem again, and I tried out several mobile phone email clients written in java, but none of them worked.

So this is at the moment the problem. If I connect from the phone to the internet directly through 3G, the email clients work for all my accounts. I don't think it's a firewall problem, because the ports are opened for this connection

View 3 Replies View Related

Software :: Squid 3.0 Access List / Remove Redirect Statement From Iptables All Internet Access Is Blocked?

Jun 11, 2010

I have an old FC2 box running Squid version 2.5. It has been running since 2003 so I am in the process of replacing it. I have a new machine with FC11, iptables, and Squid 3.0 installed.

On the old machine I use iptables to intercept Port 80 traffic and send it to Squid. By default I block all internet access and allow only sites that are in an Allowed_Sites.txt file. Within Squid I also have statements to allow certain users to bypass Squid based on their IP address.

I have set up the same thing on the new box. I have iptables intercepting the Port 80 traffic and sending it to Squid. That is working because if I remove the redirect statement from iptables all internet access is blocked.

The problem I am having is that Squid is not blocking any websites. It acts like the ACL is set to http_access allow all. I have worked on this for several hours and am stumped.

These are my Squid rules:
acl allowed_sites url_regex "/etc/squid/Allowed_Sites.txt"
acl manager proto cache_object
acl localhost src 127.0.0.1/32
acl to_localhost dst 127.0.0.0/8 0.0.0.0/32
acl SSL_ports port 443
acl CONNECT method CONNECT
http_access allow manager localhost
http_access deny manager
http_access allow Bypass_Users
http_access deny !Safe_ports
http_access deny CONNECT !SSL_ports
acl our_networks src 192.168.1.0/24
http_access allow allowed_sites
http_access allow our_networks
http_access deny all
icp_access deny all
htcp_access deny all
http_port 192.168.1.254:3128 transparent
hierarchy_stoplist cgi-bin ?
access_log /var/log/squid/access.log squid
refresh_pattern ^ftp: 1440 20% 10080
refresh_pattern ^gopher: 1440 0% 1440
refresh_pattern -i (/cgi-bin/|?) 0 0% 0
refresh_pattern . 0 20% 4320
visible_hostname FC11.proxybox
icp_port 3130
coredump_dir /var/spool/squid

View 2 Replies View Related

Ubuntu Networking :: Couldn't Access Internet Via LAN With Could Access With Windows 7?

Jul 6, 2011

I connected my laptop running with Ubuntu 11 in the LAN but I couldn't access internet.But I could ping to the other computers connected in the LAN. I tried the same thing with windows 7 in the same laptop and I could access internet.

View 1 Replies View Related

Ubuntu Networking :: Can't Access Internet Via Ad Hoc Network

Jun 13, 2011

I want to connect to a wireless open ad-hoc network to have internet access. It worked a while ago (1/2 year or something) but some update must have messed something up so it doesn't work any longer. Situation: There is a laptop that is running windows 7 and is connected to the internet via cabel. A open ad-hoc network is configuered with sharing of internet connection, status of the ad-hoc network is "waiting for users to connect". I want to connect with a second laptop that is running ubuntu 11.04. I can find the network and connect to it.

Problem: I cannot get any internet access while being connected to the ad-hoc network. So my questions are: how can i find out if what causes the Problem? I suspect a driver issue, but I'm not sure. required information from Howto post a wireless issue:

[Code]...

View 5 Replies View Related

Ubuntu :: Cannot Access Internet From Adhoc Network?

Jun 21, 2011

I've a laptop which is connected to ethernet. I want to access internet from my N900 through wifi( available on Laptop). So i created adhoc network on laptop and connected my smart phone to it. But i still cannot access Internet from my phone. Where am I going wrong?? or is there another way to acces internet from my phone via laptop?

PS: I followed the procedure given in this link to create an adhoc network.

View 1 Replies View Related

Networking :: Access Local Ip From Outside Network(internet)?

Mar 22, 2011

I have created more A record in dns. one record is link to my local ip, i have already static ip, how can i access my local website from global.

View 11 Replies View Related

Ubuntu Networking :: Network Connection But No Internet Access

Feb 5, 2010

I am attempting to connect Ubuntu 9.10 to the Internet.I have a network connection, and Karmic detects it fine. I can ping addresses within our network (e.g. the Windows computer in the next room), and I can ping the router, but if I ping, say www.google.com, it says "Destination Net Unreachable". Previously, in Jaunty, I had a similar problem.I found a workaround: launch Pidgin. Somehow, launching Pidgin temporarily edits my configuration. However, in Karmic, I have no access to Pidgin, however, and Empathy does not do the same thing. Since I have no Internet, I cannot "sudo apt-get install" anything.How can I get the Internet working?

View 5 Replies View Related

Networking :: Connected To Wireless Network But No Internet Access?

Sep 17, 2009

if i'm connected to my wireless network it only gives me internet acces for a few minutes. The connection with my network stays but i have to close it back of and reconnect before i get back online.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved