i've installed opensuse 11.3 x86_64 and everything works great. after install updates and restart i cannot access internet from wireless connection. Knetworkmanager says it is connected, i have a dhcp ip, gateway, and cannot access internet.... i tried to configure from yast and cannot access internet...
View 3 RepliesI installed 11.3amd64 as a VM under Vista/VMWare Player - all worked fine. I have now installed it as a physical system. It nstalled cleanly BUT during first boot it could not access the repos. With each repo it gave the message
- download (curl) error for (repo)
- error code connection failed
- error message could not resolve host (repo)
This was followed by a message box containing
- UI syntax error
- no widget with ID 'contents
Firefox could not access the internet (cannot find server) until I disabled IPV6 (I used about:config), now it works fine. I think the repos problem is because of IPV6 - I usually have trouble with IPV6. I tried disabling IPV6 with the following (How To Disable ipv6 on SuSE Linux | Linux Poison)
[code]......
I have a desktop computer running OpenSUSE 11.2 with two network cards installed. I would like to use both cards for connecting to the internet using different networks. The setting would be the following: eth0 is the main (default) card, almost all programs should use this NIC for connecting to the internet. eth1 is used only by a few programs, which have setting for selecting which network interface to use. The two NIC's are connected to different networks, so the IP address of the NIC's, the related subnet masks and gateways are also different.
Saying short, I would like to have the two NIC's as they would be in two separate computers. I can set the IP address and subnet mask of the NIC's. The main problem is that I can only declare one gateway. How can i setup this? I do not use network manager, I configure network cards using yast, but if needed I can of course use ifconfig directly.
I'm having a strange problem with my network connection/DNS. I turn computer the on and it recognizes and connects to wireless or wired but I can't access any Internet resources or my router. If I ping the default gateway, I get no response and I get DNS errors from any network services that run at start up. If I stop and start the network daemon then it all works fine until the next time I turn on my laptop. It does this for both wireless and wired connection.
I've tried to edit the network interface information in YaST but it says that configuration is handled by knetworkmanager and I have no idea where that information is accessed. I should point out that it all worked fine until I tried to connect to open WAP at my school and couldn't so I connected to the wired network. Next morning I had this problem when connecting to my home network. My questions are 1. What could be the cause of this error and 2. where does one configure the network interfaces when using knetworkmanager
Installed a security update for samba tonight via Opensuse updater.Now, when trying to access my home network an authentication box pops up (never used to)Asks me to enter authentication for my home network.I enter my username and password and hit enter. After a few seconds the authentication box pops up again askingfor the same indicating I have entered the wrong username / password combination (which I know I have not).
View 9 Replies View RelatedI install from openSUSE-11.3-NET-x86_64.iso. Installation was succesfull, but after install all packet on test internet / update was error. And after log in in installed system internet not work. I use router with DHCP
View 8 Replies View RelatedIs there a network trouble shooting guide for OS 11.2 that I could follow? I've shot myself in the foot so I should try to fix it.
I changed the DNS server addresses and the number of IP addresses on my router. I then set my Linux system to use static IP addressing and edited the network settings for my network adapter accordingly. I can now no longer get to any web-site.
By contrast, I also updated 1 of my Windows computers in a similar way; it continues to work without problem.
I am trying to get internet connection on Open Suse 11.2 through my wireless connection. I can connect to my network but there is no internet connection. The internet connection does work with other Linux distros and with Windows 7 laptop and Windows XP machines. I tried turning off the firewall but still no connection. What is even stranger is I can ping Google but in Firefox I cannot go to Google.
View 1 Replies View RelatedI'm kinda new to this, and usually i get help from a computor technician at school. BUT sins its Saturday, i cant get any help, and i realy need it. Well my problem is that i cant get any internet access using eth0 at my computer. I dont know what i have done wrong, if i have done anything wrong, it just reinstalled. ANd i dont know how to config it.
View 3 Replies View RelatedOpenSUSE 11.3 x64 KDE I dont know what happened it is a new install thats been running for 2 weeks . Now for some reason I can not access the internet or the router. Samba is working with Dolphin I can browse shares on local network both Windblows and Linux and ping local IP's. But I can NOT ping my router (the default gateway IP) with this box or access it with firefox so no internet. A VirtualBox of XP Pro running on this box has no problems with its bridged adapter getting out and seeing the router. I disabled the firewall, added gateway IP to network settings, disabled ipv 6 from the get go, added service provider dns's to nameservers tried opendns servers also.
View 3 Replies View RelatedBrand new to the OpenSuse project. I'm have an old AMD Duron running 11.3 and I am having no luck in connecting to the www. I'm using a D-Link usb wireless adapter. I seem to have an IP address for the PC. here is the print from ifconfig:
wlan0 Link encap:Ethernet HWaddr 00:12:0E:45:75:F5
inet addr:192.168.2.7 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::218:eff:fec45:75f5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:246 errors:0 dropped:0 overruns:0 frame:0
[Code]...
I just did a large patch on my opensuse11.3 system (upgrade of all installed packages), and whilst my network interface works, I cannot get past my router onto the internet.
I can connect to other computers on my network (here at home), I have an IP address via dhcp from my router, but I cannot get internet access, either from thunderbird, firefox, or simply by [URL] Clearly the computer was connected to the internet just fine minutes before since I did the large patch! Also, my other computers CAN still connect to the internet.
how i can debug it? It is just too coincidental I have upgraded everything and now somethings amiss!
If it's relevant, my router is a netgear WGR614v9.
A few things I've tried...
Code:
linuxthinkpad:/var/log # /sbin/route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.1.0 * 255.255.255.0 U 0 0 0 eth1
link-local * 255.255.0.0 U 0 0 0 eth1
loopback * 255.0.0.0 U 0 0 0 lo
[Code]....
recently ran into a problem with my internet access. Im using open suse 11.2 on a Dell Vostro 1520 laptop. I managed to get my wlan running and i can use firefox to access my router. In my router the laptop is also showing as connnected, dhcp reserved an ip for it.However if i try to browse the internet, no page is loading, actually no software that needs access to the web is working.
View 3 Replies View RelatedI need to implement at my sister this kind of connection: She is connected on Local area network that has about 50-80 pc's, but for internet access she must start an pppoe connection. For now when she wants to use lan she must put her local address (ps: they dont have dhcp), for pppoe she uses dhcp. Problem is that on that way she can't access lan and internet at the same time. She must disconnect from lan and then start pppoe connection and vice versa. I'm intrested if it is possible to have lan access at the same time as internet access. some kind of tunel through lan up to isp. I was googling little and so PPPoE tunneling. Is it that what I need here?
View 9 Replies View Related I cannot use the online update and any other web repository because I got the following error while using the online update:
Code:
Errore durante il download di (curl) per 'http://packman.iu-bremen.de/suse/11.3/repodata/repomd.xml':
Codice dell'errore: Connection failed
Messaggio dell'errore: couldn't connect to host
the translation is:
Code:
Error during downloading (curl) from 'http://packman.iu-bremen.de/suse/11.3/repodata/repomd.xml':
Error code: Connection failed
Error message: couldn't connect to host
I would point out that any other application that needs accessing the internet is working correctly.
I've been running Suse 11.2 KDE on a 64-bit Dell Studio 1535 since last week's release, and have had no trouble using Firefox. At some point today, however, it stopped accessing webpages -- or, when managing to grab a page, it would do so without full html rendering. 95% of the time I get an error splash, while the other 5% I get some sort of truncated page that looks nothing like it should. Konquer and Opera work fine, as does KMail.
I tried deleting the profile.int file (no luck), then uninstalled/re-installed (no luck), then uninstalled and deleted every Mozilla/Firefox file I could find in order for a fresh install -- but this has not worked after several attempts. I still cannot get Internet access. How to completely wipe-out Firefox in order to allow for a totally new installation?
I just upgraded from Suse 10.x to 11.2. Unfortunately, I didn't use 10.2 much and I('m a bit overwhelmed by the upgrade. Any advise is greatly appreciated.
After my upgrade, I lost Internet access. I don't really know my way around too well, but I did try to ping my router, but had no success. (Although I can ping 127.0.0.1).
I'm guessing that this means network access is not configured, although it looks OK to me.
Recently i started going into OSes other than Windows. So, i installed openSUSE 11.3 32bit on my system in dual boot with Windows7 32bit. Everything was okay But i couldn't find any drivers for my laptop. My problems are :
1. cannot access NTFS drives.
2. cannot connect to the internet through LAN
3. cannot connect to the internet through Wireless.
Computer's Configuration :
Dell Inspiron 14r
Intel Corei3 processor
Both the operating systems run fine otherwise
I'm trying to setup a wireless AP with my old asus eeepc, so it can act as a repeater to connect my android device on the other end of the apartment. I've already created the Wireless Access Point using hostapd. It took very little configuring, just changed from mode 'a' to 'g' and changed the channel from 60 to 1 and It was all set. Next I setup a dhcp server. Also simple enough using yast.
Up to this point, I was able to connect my android device to the newly created wireless network. However It doesn't have internet access. I guess I have to configure iptables for this, but I find it incredibly confusing! Here are a few specs to help with any examples: The laptop is connected to the internet through eth0 with IP 192.168.2.120 Hostapd is using wlan0, and I'm pretty sure it created mon.wlan0 So, to sum up, when I connect my android device to the network I can, for instance, see what ever pages apache is currently serving on the laptop, but can't access the internet.
I tried to set up my internet connection using the network manager and not the classic iufp method. At first it just didn't work but after deactivating IPv6 I got it working: firefox can connect to the internet. What troubles me is the online update with Update Applet. The following message pops up: "Error: packageKit error repo-not-available: Failed to download /media fromAlso when I go to Yast->Software->Software repositories I get the msg:Systemadministration is blocked by PID 2459 (/usr/sbin/packagekitd). Close the application and try again.Using the command "sudo zypper refresh"eates the same message.I spent already hours trying to figure out the problem without luck
View 3 Replies View RelatedI would like to be able to monitor which programs are allowed to access the internet, but a search for programs to do this has turned up nothing. Preferably, I would like a notification to come up every time an application uses the internet. Is there any (n00b friendly) software available to do that?
View 2 Replies View RelatedJust today I installed opensuse 11.3 on my Compaq CQ61. Even though I am able to connect to networks (both with an ethernet cable and wireless) I don't have internet access. I have used opensuse for a very brief period in the past and I had no such problem.
View 3 Replies View RelatedWhen I run the YAST Online Update OR Software Management OR Zypper, the Updates (or install of new software) fails when the download of the Delta RPM reaches 98%. I have added ALL of the community repositories and have Imported the appropriate certificates. When watching the DeltaRPM or normal RPM download, it starts the download at approx. 4Mbs/sec until it reaches 98% of file downloaded. Then, the speed drops to 0 B/sec and the file download fails. This then prompts a Retry which again fails when it reaches approx 98% download.
It does not matter if I am doing an Online Update, Doing a Software Management (to install new software) or using Zypper in a Terminal session, the result is the same. I have even gone so far as to connect the machine DIRECTLY to the internet, bypassing all firewalls so as to ensure it is not a firewall issue.
[Code]...
When I run the YAST Online Update OR Software Management OR Zypper, the Updates (or install of new software) fails when the download of the Delta RPM reaches 98%. I have added ALL of the community repositories and have Imported the appropriate certificates. When watching the DeltaRPM or normal RPM download, it starts the download at approx. 4Mbs/sec until it reaches 98% of file downloaded. Then, the speed drops to 0 B/sec and the file download fails. This then prompts a Retry which again fails when it reaches approx 98% download. It does not matter if I am doing an Online Update, Doing a Software Management (to install new software) or using Zypper in a Terminal session, the result is the same.
I have even gone so far as to connect the machine DIRECTLY to the internet, bypassing all firewalls so as to ensure it is not a firewall
[Code]...
I am looking for libtag-extras1-1.0.1-23.1.x86_64.rpm, but don't seem to be able to access it on the mirrors.
View 1 Replies View RelatedYesterday I applied the su security patch to my openSuSE 11.2 x86_64 system.After applying the patch, any attempt at su failed, and after rebooting the system earlier this morning any login (root, user, otherwise) fails with a "Permission Denied".Is it possible that the su update somehow messed up my (standard) pam settings?
View 10 Replies View RelatedAttempting to compile an application that is not located in any of the repos yet for 11.3 64 bit. I have downloaded the appropriate src and untarred it. However, when I attempt to run the ./configure command here is the error I receive. checking build system type... Invalid configuration `x86_64-unknown-linux-': machine `x86_64-unknown-linux' not recognized configure: error: /bin/sh ./config.sub x86_64-unknown-linux- failed
I have made sure that I have all kernel-headers packages installed and am unsure as how to proceed. I tried using the command "./configure --build=x86_64" and then receive an error stating that the "SYSTEM IS NOT SUPPORTED" and continued errors stating that gcc is not installed, eve though it is.
In the live CD, auto eth0 worked fine.After installation, it cannot connect.I am using vaio laptop VPCCW16FG, there is a known display bug therefore i am booting into the OS with 'nomodeset'.i have no access to the internet and cannot update repos, therefore i cannot work around the bug.
View 3 Replies View RelatedI just installed fedora on a customers laptop of mine and just trying to get everything working. I hooked up a wireless PCMCIA linksys card and got connected to my wireless and went through the first 250+ updates, all that went fine, so I know I am getting internet access. Everytime I open firefox though I cannot connect to any websites, like I said I am a noob so my troubleshooting skills are very limited with linux, anything I can try etc.
View 4 Replies View RelatedAlthough Im using SuSE since 7.2 this is my first forum post here. I just plugged in my iPhone with USB and 11.4 created an eth1 interface for the iPhone and also loads the ipheth kernel module. Anyhow I am not able to acquire an IP address using DHCP. The iPhone OS is 4.2.1 and its an iPhone 3G 8GB black
View 2 Replies View Related