I'm installing OpenSuse 11.4 to a HP DL180 G6 server, with no luck. I go through the installation process when booting up from the DVD, and when it finish and restarts in loads Suse and then goes to a black screen and doesn't respond.
View 9 RepliesI have my brand new Dell latitude e6410 delivered with Windows 7 already installed. I want a dual boot and I decided to try SUSE for the first time. I used the installation DVD, the installation seemed to end up well. The problem is that already at the first reboot, the screen went completely black. By pressing ctrl-alt-del I can reboot the laptop. It seems to me a problem with the graphic card.
My setup is:
Dell Latitude e6410
Intel i5 m560 @2.67 GHz
nVidia NVS 3100M
4Gb DDR ram
Intel 82577LM Gigabit Network connector
If I start in failsafe mode, the X server starts, I have KDE, although with a somewhat sketchy graphic, I can use SUSE almost normally. The main problem in this case being that the system doesn't find any ethernet/wi-fi device, so I cannot connect to the Internet (I'm writing from Win7 right now). I tried choosing the default SUSE boot with the additional boot option "nomodeset" at the grub prompt. This is a suggestion mentioned in another post on this forum, although in that case the problem was coming from a bug dealing with an Intel graphic card. The system goes up but then kde doesn't start. I'm asked to lgin at a prompt. If I try to launch kde from command line (startkde), it complains that the variable $DISPLAY is not setup.
This is where I am now. I'm quite out of ideas, so I want to ask you few things. First stupid question: is the problem coming likely from the drivers of the nvidia graphic card? Second question: in that case, how can I fix it, considering that the linux partition is "isolated"? The fact that in failsafe SUSE doesn't see any network adapter concerns me a bit.
I'm having a really odd problem since I upgraded to 10.04 on my IBM T40 laptop. Every now and then, especially if I'm using Firefox (so it seems), I will be in the middle of something and suddenly I get a black terminal screen that flashes a few lines ending in "checking battery state" and I get bounced back to the login screen. I log back in and all my work is gone (Firefox and whatever else was open has closed). I was on the web for a while tonight and in a few hours it did it three times. I never had this happen before in 9.10.
Any idea what's going on? If it matters I'm on AC power when this is happening. I haven't used it long enough on battery to know if it does it then or not.
When I load Ubuntu, it goes to the desktop screen, shows my desktop picture, loads Pidgin which I have set to start on startup, loads Icons, and then the screen goes black. The mouse cursor shows up, I can move it around, and then it goes black again, and the mouse cursor shows up again. This repeats a few times until the cursor freezes. This started happening after I tried fixing a bug with new drivers for my Intel 845gl video card. The instructions I followed are these:
Code:
To use the available fix, run the following commands:
pt-add-repository ppa:glasen/855gm-fix
apt-add-repository ppa:brian-rogers/graphics-fixes
apt-add-repository ppa:glasen/intel-driver
aptitude update
aptitude install linux 855gm-fix-dkms
aptitude dist-upgrade
,taken from here.
I have tried some of the options in recovery mode from GRUB menu, none really work, except booting with default graphic configuration, or something similar like this.
After entering runlevel 2 and gdm loads, I only get a black screen. I hear a beep that indicates gdm has loaded, but everything stays black. Trying to switch to a console using ctrl-alt-f1 does absolutely nothing.
At one point, I disabled gdm from starting in runlevel 2, and rebooted. I then typed into tty2 "sleep 60 ; reboot" and in tty1 "gdm" and hoped for a reboot if the graphical login didn't appear. No reboot occurred, my black screen remained.
I've issued acpi=off at kernel command line (from grub) and disabled all acpi services. That seemed to work for a few hours but now I get the black screen again every time. There's no option in the BIOS to switch from acpi to apm, so I've done all I can do on the software side of things.
[Code]...
I have a bad problem with debian 5.0 . I have installed it all right with no fail or error and when it boots,i just see a black screen with nothing else. My graphic card : Nvidia 9500M gs. I tried ubuntu,fodero but both of them were same after installing debian (Before i didn't have this problem)
View 3 Replies View Relatedfinally just got ubuntu to install on my emac a1002, I had to use the powerpc version. The install went fine, it restarted and loaded ubuntu, but after it loads goes to a blank black screen. And I imagine it sits there forever, yet I've only left if for about 5mins or so. The emac is from 2003, and has a 1ghz processor (Powerpc) and has 256mb ram.
View 1 Replies View Relatedjust installed ubuntu on my win 7 laptop using the wubi.. after the install it said restart,so i restatred and booted up ubuntu which went sound,it then says finishing installation.. ubuntu comes up does the partions then started copying files then once it had done this the screen went black with loads of writing on it..it seems to just stay like this.. i left it 30 mins the restarted laptop again..laptop working sound booted ubuntu again and the same thing happened..
View 1 Replies View RelatedI try to install openSUSE 11.4 KDE RC 2, unfortunately I show black screen after GRUB screen. I must press Power button to turn off my computer. I hope it won't on openSUSE 11.4 stable. I'm waiting for downloading openSUSE 11.4.
View 8 Replies View RelatedI've got a problem with my openSuse 11.3 for a few days. This is my first Linux so i'm kind of rookie.OK, let's start.I installed it something like 1 month ago and everything looks good until now. When I turn on my PC and try to login (deskop mode) login bar goes from 30% to 50% and then appears a black screen, nothing more, just deep black (cannot type anything etc.) I use GRUB - Windows, opensuse deskop mode and failsafe mode. Failsafe mode works good, but I have no idea what should I do because I didn't change anything. I even done a reinstall of OpenSuse and after one day I've got the same black screen.Someting wrong with grapfic card drivers? (ati 4850, downloaded from ati page, works good for 1 month) maybe some kind of new update which was installed automatically?
View 3 Replies View RelatedI'm running openSUSE 11.2 on a Thinkpad T61p with nvidia graphics. I'm running the proprietary nvidia driver.The battery ran very low and the computer suspended itself. After I woke it up, the desktop is completely black.After troubleshooting as much as I could, I did ctrl-alt-backspace, which brought me to a normal (non-black) login screen. However, as soon as I logged in, I was back to a completely black screen. But the system is operating.I rebooted the computer (warm reboot as well as cold restart) and each time the video is normal until I get to the desktop and all I get it black.Everything was normal until the pm suspend.Suspend has never worked exactly right, so I don't normally use it. But in this case, it used itself Next step: I logged in to console mode and looked at the logs. The only messages of interest seem to be in Xorg.0.log I found a couple error messages that might be of interest:
(II) LoadModule: "nouveau"
(WW) Warning, couldn't open module nouveau
(II) UnloadModule: "nouveau"
[code]....
I'm on a JFK assassination binge right now
Every ten minutes or so the screen goes blank and I have to hit the keyboard or wiggle the mouse to bring it back to life
This isn't hibernation...for the audio still works
I've looked around the control center...right clicked the desktop and looked at options there
I have been using OpenSuse at work for years. My Windows 7 machine crashed on me. Instead of spending the time to fix it, I decided to take the plunge and install 11.2 on my home system. I have 4 one TB drives. My RAID card has a 2x2 1/0 RAID array defined (sdb, sdc, sdc, and sde). A fifth hard drive, outside of the arrary, which is a 250GB drive (sda). It is a software RAID. Here are the partitions I set up in the installer.
On the raid:
1.75 TB on /home
2.01 GB on swap
48.55 GB on /tmp
Off of the raid:
sda1 115 GB /
sda2115 GB /boot
(I know these are really big but I did not want to put any data outside of the RAID) In the final Installation Settings screen, I chose Booting and change from booting from the MBR to the /boot partition. The boot loader type is Grub and the status location is at /dev/sda2. I select Install and it installs without any error message.
After it installs, it restarts and I press ESC to see what is happening. It skips boot.cycle and continues to load to "starting HAL daemon ...done" and then the cursed black screen. I cannot SSH into it. It just sits there and I have to do a hard resest. Once I restart it, it boots into the non-RAD drive I get the follwing error message:
GRUB ..(it went to fast for me to get the rest of it)(hd1/1) message: file not found and I get the option the change the boot options of the Desktop -- openSUSE 11.2 and Failsage -- openSUSE 11.2 . I select e to edit the boot section of desktop and see
root (hd1,1)
kernal /vmlinz-2.6.31.5-0.1-desktop root=/dev/disk/by-id/ata-ST32508...
intrd /initrd-2.6.31.5-0.1-desktop.
I tried changing the root (hd1,1) to 0,1 1,0 2,0, etc with no luck.What do I do? I need to boot into OpenSUSE and finish the cursed installation.
PS: You can tell I work IT with the uber amount of details I put into this
I have registered a problem similar to the one reported in this thread: Solution to black screen problem in opensuse11.2 - openSUSE Forums
after installing openSUSE 11.2 from DVD, and rebooting the system a blank screen appears after booting process is completed.
Initially, I was thinking that was 'cause of the installation of ndiswrapper drivers (see command "modprobe ndiswrapper" not working - openSUSE Forums) but after the 4th (!) installation of openSUSE I really don't know what to think...
Sometimes openSuse boots regularly, and sometimes not... seems that there is no difference if I restart the PC or I turn it off and then off. Result is the same: sometimes I get the user desktop and sometimes not...
As explained in my previous post, I have checked the disk but all seems ok.
Now I cannot use the PC even in failsafe mode... I get always a black screen.
But what is more surprising is that I have 2 identical (identical!) PC with the identical hardware, and identical bios configuration. Only the monitor is different. Well, said that, one is working the the other one not...
To be honest, the working PC was an openSUSE 11.1 systems updated to openSUSE 11.2.
I think that must be something wrong on the distributed openSUSE DVD..
I tried both installing 11.3 on top of 11.2 and a new install with the same result on a couple of different mac pros (with 2009 ATI Radeon HD 4870 with 512MB of GDDR5 memory, 2.66 GHz 2x4 core Xeon 3500, 24 GB of memory). The install was done via the downloadable dvd from opensuse.org. The graphics of the install process looked fine as well as the configuration. When it came time to boot, however, the suse splash screen showed up and then the monitor went dark. The graphics seems to be frotzed. Now attempting to boot from the DVD does not cause the display to do anything. Even putting a mac DVD restore disk (and using C during boot) does not result in anything on the display). Any ideas of what the installation could have done -- seems like a no-brainer that something is screwed up with the graphics card, but I have no real proof and even less idea of what to try next.
View 2 Replies View RelatedI very frustrated at this point. I have tried to boot OpenSUSE 11.4 from the usb flash drive iso and CD iso. After I restart my computer the boot menu comes up and I click the boot option and the screens loads a bit and then goes black. I have also tried the text installer, but that doesn't work either. I know the problem must be my graphics chip. I have a integrated Intel HD Graphics chip. My laptop is a Gateway NV79. How can I get the graphics to work?
I've tried everything I can think off. I'm not the most computer savvy so if someone replies I would appreciate a dumb-down explanation on what to do with clear steps, if possible. Note: I'm dual booting with windows 7. The graphics problem is not just OpenSUSE. I tried Ubuntu 11.04, Kubuntu 11.04, Fedora 15 and they all have the same problems. In Fedora 15, I was able to boot in but I got an error message that said Gnome 3 fallback and I couldn't get the graphics to change to standard mode
I get a black screen when I install the driver, plus:
Code:
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02)
01:00.0 VGA compatible controller: ATI Technologies Inc Redwood [Radeon HD 5600 Series]
is there a method to install the drivers on openSUSE 11.4?
I've installed 11.2 KDE on a very old samsung V20 specs here: [URL]... My problem is that when I boot I get a black screen with just the mouse pointer. I can boot in failsafe fine, but the graphics are horrible. My question is, is there a workaround or am I flogging a dead horse with this laptop? This is my first venture into Linux, and I was really keen on leaving windows far behind. I've tried quite a few sax2 commands to no avail.
View 2 Replies View RelatedI recently installed 11.1 via unetbootin from the network onto an old Sony VAIO laptop. After the installation completed, I suppose the OS started to boot, but I was presented with a black screen. I heard "chimes." The black screen does not provide any visible feedback from mouse or keyboard input. I hard rebooted and was presented with an interesting background graphic (grayish, I think) that faded to the same black screen.
View 9 Replies View RelatedA few days ago I updated my openSUSE installation on my Acer Aspire 5920G notebook from 11.1 to 11.2, but I haven't been able to get any kind of graphical shell loaded. Using the regular "desktop" option in GRUB results in a black screen. seems my PC is still responsive though as hitting Ctrl+Alt+Del like a mad man results in the PC getting rebooted after a while. I had the same "black screen" issue with the KDElive CD and the regular installation CD (Yeah, I should have known better than to do the upgrade...).
When opting for "Failsafe" in GRUB, I reach a command line. Before that it seems to try to load GNOME (you get to see the cursor) but fails at it a few times in a row. When I try to start GDM afterwards from the command line, it gets into a loop in which it tries to load, then crashes and then tries to load again, endlessly.I have installed the newest NVIDIA drivers "the hard way", and my card (NVIDIA 8600M GT) is on the list of supported devices on the NVIDIA website. SaX2 seems to work OK with it.
I'm having a rather peculiar problem booting into openSUSE 11.2. After the installation (which goes fine), i get a black screen and my system freezes.
In detail, I can see the splash screen and booting details, but at the moment I am supposed to see a login manager, i just get a black screen. Sometimes it has a cursor indicator in the top left, sometimes it doesn't. Same thing happens in failsafe mode too.
This happens over and over, no matter which installation type I choose, 32bit or 64bit, KDE/Gnome/XFCE.
My problematic box is:
AMD Athlon 3200+ 64bit
2GB DDR
ATI Radeon x1950pro <-- which I believe might be causing all these issues.
I have been trying to fix this for some time, on and off, and have been unable to, I have also ben unable to find a solution in the forums.I have installed openSUSE11.2 GNOME on a laptop, the install went fine, and it runs great, except for two problems:When I start up the splash screen doesn't show (this isn't really important, and I am happy to watch as everything is loaded)When I shutdown/reboot the computer freezes and I have to use the power button to switch off.This doesn't happen every time I shutdown, but most of the time.The freeze happens at different points of shutdown, so I don't know where to find what is causing the problem.As I mentioned point 1 is not really important, although I would like to know why this is happening, but problem 2 is very important.
View 9 Replies View Relatedi've just tried to install openSUSE on to a spare hdd, i've also got windows 7 on another. After installing everything and the computer went to reboot the screen just went black and didn't restart. After restarting it myself, i turned the computer on and got to a menu that says:
openSUSE
failsafe
windows
When i tried to go to openSUSE it seemed to work and a long list of text came up but after a few seconds it went to a blank screen. The same thing happens when i go to failsafe. so i'm not really sure what to do, i would have tried a few things i've found from searching but can't get to the command prompt on failesafe.
I've got an ati readon hd 4750 video card.
I had to re-install openSUSE11.2 but I kept having either black screen or mouse cursor freeze. Using sax2 to change video driver didn't work whether "ati", "radeon" or "vesa" was selected. I finally came across a solution: 1. Log in at run level 3 with acpi=off, no apic,F3=vesa, then become root 2. YAST -> Miscellaneous -> Live Installer, etc. 3. Reboot 4. If black screen, force a reboot and repeat step1 5. Autoconfig restart? Yes 6. When installation is finished, reboot 7. Boot option: 3 acpi=off noapic F3(vesa) 8. Login as normal user then become root 9. #YAST > Online Update 10> #YAST > Edit Bootloader
11. Edit Grub menu: Add the following to the end of the kernel line (under heading: kernel options...): vga=792 acpi=off noapic. Note that vga=792 is from a LILO config file example, which has the side note:"vga=792 #you need to do this so it boots up in a sane state". I came across this from "Framebuffer HOWTO: Using framebuffer devices on Intel platforms" Your Grub menu may also show vga=0x317 but this is because you might have selected 1024x768 screen resolution;it has nothing to do with vga=792. Vga=792 is what essentially solves the black screen problem.
I have a problem after "Loading Linux Kernel - 100%".It mean when I chose "Installation" or "Check installation media" after boot screen, I see "Loading Linux Kernel" from 0% to 99% and after that I see only Black screen for long time. Even NUM LOCK key or Ctrl+alt+del has no resultThere is no a problem with 11.2 and 11.1(current OS).Machine: HP xw8400, 2 CPU XEON 3.0Ghz, 4GB RAM, 2x250GB HDD SATA, NVIDIA Quattro FX 1500 256MB.The same problem with VirtualBox (on the same PC).
Last line in "text mode Installation" is :
...
[ 0.040974] Checking 'hit' instruction... OK.
[code]....
I've down loaded the live CD for SUSE 11.3 and, using isohybrid and dd, I put the contents onto a USB stick and made it bootable. All good so far.
I then installed SUSE on one of the partitions on my hard disk (Windows is also on the disk). I set 4GB for SWAP, 16 GB for ROOT and the rest ~270 for /HOME.
I set the bootloader to be installed in the MBR.
The installation completed with no problems indicated.
I was asked to reboot and did so, removing the usb stick so that 11.3 would boot.
The reboot failed! I was presented with a black screen and nothing else happened.
I tried again, selecting openSUSE 11.3 from the boot menu. - Again a black screen shortly after pressing enter.
I can boot in Failsafe mode and then login with text prompt. I can't boot into runlevel 3 (same problem - black screen)
Does anyone know whether this is a problem with network configuration or graphics?
I have a notebook with ATI Radeon Mobility HD 5650 graphics card and
ATHEROS ar8132 ethernet controller.
I Have installed openSUSE 11.3 using VMWare and liked it so I thought I would install as my main OS. So I downloaded the latest livecd Gnome and created a usb install using imagewriter with suse. I can boot to the initial menu asking if I want to boot the livecd or install. If I choose either it will begin to show a lot of things on the screen scrolling really fast and then the screen will go black. I've waiting up to about 15 minutes with no result.
View 9 Replies View RelatedI have installed ati drivers looking at this HOWTO ATI Installer HOWTO for openSUSE users
But after reboot i see only black screen....
My vga is ati hd4770. Looking for a full tutorial how install drivers (maybe with screens). Please help me.
With ubuntu/linux mint everything was working perfectly.
Configuration: AMD 2500+, 2GB RAM, ATI HD3850 AGP
Problem: Can not install OpenSUSE 11.3. Boot from the disc - the installation screen resolutions, modes of installation - everything is in order. But when the installation can proceed - loading (logo) and just a black screen - possibly the installation goes - but no picture. Also try to set mode "vesa" - loading equipment "ok" ... "ok" ... "ok" ... "ok" ... and again in the black screen.
Here is the solution. (I don't know how to change the title of the original thread to indicate that the problem is solved, so I've started a new thread with a link. There must be an easier way!)
View 5 Replies View Related