my system stopped booting after recent update.When I select desktop it goes to splash screen an dies.Have to hit reset key.If I select nomodeset it boots fine excepts graphic resolution is 1280x1024 instead of 1680x1050.System is sandy bridge, Asus P8H67-M EVO, Intel Graphics enabled no other grapics cards, Suse 11.4 64 bit.I do my updates with zypper up.
View 9 RepliesToshiba notebook is set up to triple boot win7, mepis 8.5 and os 11.3.Recent update of os11.3 left system with boot failure, "file not found".I booted mepis and used utility to reinstall grub, but no joy.
Appeared to install ok but on reboot, sda5 identified as 'mepis' not os11.3 and would not boot. Win7 & mepis boot ok.
Next, booted live Parted Magic and repaired as per another thread here, but again, no joy.NONE of the systems will boot.Rebooted mepis live cd and reinstalled grub again. Sda5 still identified as mepis and will not boot. Win7 & mepis boot ok.
This morning I did an update on a current F13 system with NVIDIA Graphics card. System gets to a complete white bar across the screen followed by "FEDORA 13" . This all starts blinking and goes no further.
View 7 Replies View RelatedI have an EEE 1000 that successfully connected to WPA networks until yesterday. I tried re-installing the RT2860 drivers that had been previously modified and did not have success.
Additionally, I just installed 10.04 on a Gateway laptop that's a few years old. It immediately connected to the WPA network and I ran the updater. Lo and behold, after updating it no longer connects to the network.
after a recent update my policykit permissions stopped working, and I can't understand why.An example: mounting a flash drive requires password, hinting on rg.freedesktop.udisks.filesystem-mount. /usr/share/polkit-/actions/org.freedesktop.udisks.policy has the following:
Code:
<action id="org.freedesktop.udisks.filesystem-mount">
<description>Mount a device</description>
[code]....
Firefox 3.6 "Namoroka" stopped working after a recent update. Clicking on my panel launcher or the launcher in the applications menu does nothing. I even tried starting Firefox from the terminal and got an error message: "(firefox-bin:3592): GLib-WARNING **: g_set_prgname() called multiple times", whatever that means.I would be willing to rip out Firefox and start all over again but I don't know how to remove the 3.6 version. I couldn't find a method in the Software Center for doing that graphically.
View 7 Replies View RelatedMy Laptop Config is as follows.
Compaq Presario V3700
AMD Turion64
2GB Ram
Windows Partitions
/dev/sda1 == C: (WINDOWS)
/dev/sda2
[Code]...
I have been carrying out updates of both Vista & SuSE whenever i operate in them.
One (Not So) Fine Day, when i Choose from the Grub loader "Microsoft Windows Vista SP2" option it just din't boot into Vista. I have Tried many a time.
My First doubt was towards Vista only, so i choose the "Windows Recovery Mode" option from Grub. It went into the Recovery mode. I ran Memory Tests on Windows Partition, took its own sweet time, whatever missing indexes and all it carried out and finally gave the Thumbs Up result. After that, i carried out Startup Repairs, all came out well. So, Yet again i restarted and tried to get in Vista. Nope, dint work.
OpenSuSE 11.1 updated on Saturday to all of the latest patches and stuff. I was a bit behind, so quite a few things got updated. Most of them probably don't matter for this problem.
Prior to Saturday, desktop effects were working fine. After, they don't. Gnome still works ok, but attempting to go in to the "Desktop Effects" configuration just hangs for a minute (spinning "wheel" cursor) then nothing happens ("arrow" cursor returns).
Looking at things via "ps ax" I can see that clicking on "Desktop Effects" starts process(/usr/bin/python /usr/bin/simple-ccsm).
Running this from a CLI produces:
After which nothing happens and I have to hunt down the PID and kill it.
Searching for this "tuple index out of range" error, I found a couple of 2008 references, but those are for much older version so I'm thinking that they're probably not relevant. Nothing else seems to apply.
I'm new to openSUSE, this is the first time i try to install openSUSE version 11.4. on my IBM Thinkpad T43 (on which SUSE Linux version 8.0 has been running before without problems). I have downloaded the ISO images and successfully burned the ISO images on a blank DVD. Having placed my openSUSE DVD in the drive and rebooted my laptop I can see the boot screen.
I then select installation with arrow up/down and press enter. Choosing language and keyboard layout works fine, as well as accepting the license agreement. However, when it comes to 'System Probing' the installation stops at 'Search for system files'. The cursor shows a little turning disk but the rest of the screen is blocked.
I am running Suse 11.0 and the system had stopped working. I booted from the disk and chose repair system. Now I can get to the Give root password for login and it accepts the password, but I get the line
(repair filesystem) #
Microphone used to work well, but now it does not Indicator in Gnome sound properties does not move and there is no sound in Skype.
View 2 Replies View RelatedRecently I updated my openSUSE 11.2 and I'm not too sure what all were the recent updates but I suspect networkmanager also got updated. After I restarted my machine, my laptop fails to connect to the wireless access point. I tried both in gnome as well as KDE but the same error. This is the log I found in my /var/log/NetworkManager which I believe should give some pointers.
Code:
Jul 8 15:08:42 AshSuse1520 NetworkManager: <info> Activation (wlan0) starting connection 'Buckeye Plaza'
Jul 8 15:08:42 AshSuse1520 NetworkManager: <info> (wlan0): device state change: 3 -> 4 (reason 0)
Jul 8 15:08:42 AshSuse1520 NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
[Code]....
I did a search of this error in google and all I got were few results which complained about bugs in some debian distro.
My wireless card works fine and so does the access point I try to connect to since my Ubuntu installation is able to connect fine as well as my windows Xp.
Yesterday I did follow exactly the description how to build a live system on a USB Stick with the additional second partition for the data of Live_USB_stick. So far I had success, as my Netbook did start booting and loaded the OpenSUSE 11.2. Then I rebooted the Netbook and it never again comes up with the 11.2. It looks as if it would stop somewhere at starting the graphical system, but I'm not sure.
Today, second try, I created the USB stick with the 11.2 Live System only (no second partition). My Netbook starts booting and shows the 11.2 system successfully, also further boots are the same successful. Then having created the Live system with the second partition again, results in a un-bootable Netbook again (not even the first time it comes up).
What I wonder when I did check the USB partitions: the one (sdg1) with the Live-CD can be mounted and the content is readable. The second one (sdg2) cannot be mounted; shouldn't it be mountable and shouldn't it be formated with a file system? Did anyone have some experience on this? Or, at least, the people having a running persistent live system, what does the partition them show up?
I currently have Ubuntu 10.04 LTS installed on my PC. The details of how it got installed I cannot explain... I installed it on a HD that was not partitioned and I accepted all the defaults that Ubuntu suggested. So as far as I know right now Ubuntu "owns" the whole HD.
I now would like to create a dual-boot system by installing openSUSE 11.3 alongside Ubuntu 10.04 LTS. By reading things here and there, my guess is that I need to create a partition for openSUSE by shrinking the one for Ubuntu. But I am really not sure.
So I downloaded the CD version (GNOME) only of openSUSE, launched the installer and the process came to the following suggestions which is basically all Greek to me:
* Delete partition /dev/sda1
* Create root volume /dev/sda1 with ext4
* Create volume /dev/sda3 for /home with ext4
* Use /dev/sda5 as swap
As I said before, what I would like to do is install openSUSE side-by- side with Ubuntu and create a dual-boot system. I do not want to delete Ubuntu! I got scared by that "Delete partition /dev/sda1" thing mentioned above and so I aborted the installation.
What is the installer suggesting? Has it realized that I already have Ubuntu installed and that I want to create a dual-boot system?
I got three times fsck failure during system booting, fixed issue by reinstall whole suse last two times, this time I really do not want reinstall.
View 4 Replies View RelatedIm probally just being a noob here but for the projects sake I thought it would be good to identify this problem. I have an old advent laptop and I tried to install Opensuse from DVD on it. I followed the installation as normal but when I tried to boot it said some sort of check was forced and then I have to enter the admin/root password upon doing this I got the message system repair # in red. I have tried to repair the system through the installation DVD and tried re-installing it but I still get the same message.
View 9 Replies View RelatedI recently installed Suse 11.1 from the Live CD on an older PC. Suddenly, when booting up yesterday, the system announced corrupted IPtables and didn't load KDE. After login, I tried commands like KDE, run KDE but the bash didn't understand the commands.
So I booted from the live CD, but I can't find an option in the install menu to repair the existing installation. The help in the boot-up screen claims there should be an install option, but it doesn't show it at that point, only after KDE has started from the Live CD.
Since I've already made some changes (newer firefox, downloaded thunderbird etc.), I would like to keep and repair the current installation, instead of a new installation.
I don't however understand enough about the automatic partitions I'm being offered in the installation menu to know what to choose to keep the existing files. I did choose the offered automatic partitions the first time, and have now several partitions, home swap and so on.
Second question: While 11.1 was still running nicely, I could not find the option to upgrade to 11.2 in the Yast menu (I don't know any batch commands, so I only use Yast for installation). Looking at the download sites on opensuse on the internet, I saw an update option, but when I tried to add that URL to the Yast repository, it somehow didn't work. I also didn't see a nicely packed .rpm or similar update package.
Third problem: I downloaded a newer version of Firefox and Thunderbird and after some tries got Yast software repositories to install them. But the Avira antivir tar.gz package I downloaded, did not appear on the Yast repository manager. Doubleclicking to Ark didn't work, and when I went to console and tried to run the install file in the zipped package, it wanted parameters, and I didn't know what to answer.
how to update my system online (for example my firefox 3.0 to 3.5) but i can't figure out how this possibly works. I tried the "online update" using Yast2 but apparently (according to Yast) there is nothing at all to be patched on my system. I tried to click on the Firefox-3.5.5 rpm in the repository web-interface and open it using "install software" but the process aborts because of unresolved dependencies. Is there an easy way to update software without having to download/install every dependency manually?
View 1 Replies View RelatedLike many others it seems, my wireless has stopped working since a recent upgrade The answer does not lie in analysis of logs, settings etc. but surely with those who did it - they should provide a fix. I cannot believe everyone expects each individual users to go into their own analysis of why this is no longer working as it is clearly widespread. I have been using Ubuntu for 18 months without this problem on the same dual-boot laptop, and it still works on Windows as before, only Ubuntu 10.4 has recently stopped my network card from working.
I need to know when this will be fixed. I have been embarrassed by promoting Ubuntu to many colleagues who now also cannot work at home on their wireless networks. Seriously disillusioned I may start looking for a more stable alternative to Windows.
i have a dell 1501 that has been upgraded from 10.10 to 11.04. everything was working okay. and then the user ran an upgrade recently. subsequently the wifi has mysteriously stopped working. it connects okay if one plugs it directly into the router but the wifi seems to have just stopped working.my mini 9 connects fine to the netgear wifi router using wireless.when i run the system tests for networking i get the errors..."root could not find def gateway info /proc""root could not find default gateway by running route"here is the output from some diagnostic commands.NOTE:this is similar to a post titled "wi-fi dead?" but the output is not quite the same...
lauren@lauren-Inspiron-1501:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
[code]....
I upgraded my Dell 2.53G machine from 10.3 to 11.2 (KDE desktop). Everything seemed fine for the first day. Then the whole desktop froze. No screen update, no keyboard, and, though you could see the mouse move, clicking didn't do anything. The only way out was to pull the plug.
After multiple attempts at fixing it failed, I repartitioned the disk and tried a "clean install". Everything worked for about 2 hours. The system is currently frozen. The harddrive is quiet. The only "3rd party app" was Adobe Flash, pulled from the Non-OSS repository.
i have running more than 50 servers with openSUSE 11.2 for a long time without any problems. After upgrading 30 server to 11.3 some of them are freeezing after one or two days. I can ping, but i cannot log in. At the console i can type in the user and the nothing happens, system has to reboot.
All servers are Hewlett Packard Proliant G4,G5,G6 with 32bit and 64bit. No errors or hints in the systemlog.
Recently i add a lot of repositories for new apps but do0ing a zypper up after that left left many things broken ,first the my system has added 2 more entries in grub menu namely, opensuse 11.3 desktop-2.6.34.7 and opensuse 11.3 desktop-2.6.34.7-(failsafe) why are these added and now when I simply boot opensuse11.3 from menu though it starts but has no sound and typical errors shown .
Firefox is broken. how could I reach a stable state now I have these repos only code...
I'm running 11.2 with standard repositories (plus packman). I want to install a recent kernel and then compile some variations of it (to investigate a hardware problem).
So I took these steps:
(1) add the 11.2 Kernel:/HEAD repository
(2) enable multiversion in zypp.conf
(3) use YaST software management to select the kernel development pattern
Note that at the moment, the standard 11.2 kernel ( 2.6.31.14-0.6-desktop) is in use and I have not selected any packages from HEAD. But it has installed 2.6.37-41.1 versions of all the kernel packages I didn't already have (source & docs etc) instead of the 2.6.31 versions. /usr/src/linux symlinks to linux-2.6.37-41 instead of to a directory for the running kernel!
(1) it should have loaded the packages corresponding to the running kernel
(2) it's not supposed to switch repositories
A recent kernel update seems to have misplaced the Kernel Headers. VMWare needs these headers and cannot find them. Attempting to run VMWARE gets the message: Kernel headers for version 2.6.31.12-0.2-desktop were not found.
View 4 Replies View RelatedIs it just me or your update applet also stopped working recently? I'm running Factory KDE-4.4.2 and openSUSE-11.2. It's always "Checking for updates..." without finding any, even though I can always see new ones through Yast - Online Update. And sometimes it asks me to accept some key, when I click OK it asks me for a root password but after I type in half of the password it simply disappears and starts "Checking for updates..." again without end.
And YAST doesn't show any newer packages anymore but rather has "Switch system packages" on the top. If I click on that, then it starts showing newer packages and wants to update them all. But what if I want to use Packman's packages for multimedia and Factory KDE for KDE? If I select "Switch system packages" for KDE then it will update, for example, Kaffeine to KDE's but I want to keep it Packman's. If I search for Kaffeine, it shows no newer packages, but if I go to Versions, there's clearly a newer version there!
I have been trying for the last couple of days to upgrade a Xen guest running on Xen Server 5.5 from 11.0 to a more recent version. I have tried both 11.3 and 11.1. The upgrade seems to take, but it fails on the initial boot. It seems that it is expecting the root partition to be on /dev/sda2 - however I believe it is supposed to be /dev/xvda2. Initially when fstab had /dev/xvda2 I had a warning, so I changed fstab through yast to use the drives uuid. I've also tried zypper dup - but that gave all sorts of dependency errors. For kicks, I thought I might try 11.4 next. Am I out of luck and should just go with a fresh install?
View 1 Replies View Relatedmy laptop(dell xps m1330) takes around 2'30" to boot, I don't remember when it started but it wasn't always that slow. even looking at bootcharts I cant seem to figure out what that could be
full-size bootchart here: [URL]
btw it powers down in less than 5 seconds
I did an update yesterday and since then my mouse stopped working.
/var/log/messages contains:
Code:
Obviously the mouse is recognized but still does not work.
Running openSUSE 11.2 with HP All-in-one 3055 printer/fax/scanner attached through network.
Using hplip package.
Printer works just fine. Scanner did work for quite some time, however it stopped working after some update about a month ago (using only opensuse update repo).
When doing hp-scan I get following error:
Checking all the logs I can think of I can't figure this one out. Tried newer hplip package fom HP site same issue (I have two systems, on one I've tried the new driver, on one only using opensuse update repo ...both same issue)