I just got openSUSE 11.2 set up on my home server. The machine has two 2TB HDDs, the first (/dev/sda1) is partitioned thusly:
10GB /
1GB swap
1.82TB /home (/dev/md1 in RAID1 array)
[code]....
Why do I keep getting .gvfs (gnome virtual file system) file appearing as corrupt in /~/usr directory, I can get rid of it by unmounting, but it re-appears later on. It is causing problems as it interrupts my backups (which are automated) with an error message,ListError .gtk-bookmarks/.gvfs [Errno 13] Permission denied: '/home/jimt/.gvfs'
drwxr-xr-x 2 jimt users 4.0K Jun 22 22:00 .gstreamer-0.10
-rw-r--r-- 1 jimt users 132 Jun 24 11:50 .gtk-bookmarks
d????????? ? ? ? ? ? .gvfs
-rw------- 1 jimt users 4.3K Jun 24 11:50 .ICEauthority
drwxr-xr-x 3 jimt users 4.0K Jun 23 08:41 .icedteaplugin
I want to cause damage to a file system and then try to restore it. I want to use a VM first and when I've learned a little try it on an old HDD. Any ways to damage a filesystem non physically is welcome!
View 2 Replies View RelatedI have an Acer Aspire One running NBR 9.10. A few days ago it "went wonky", wouldn't boot and would just seem to start and then shut off before getting to the logon screen. I managed to boot from a USB stick and run check and fix in Gparted. It found a slew of errors in the file system. Unfortunately, it still won't boot, now it just hangs. I assume some of boot files were damaged.
Now I have two problems:
1. Is there a way to repair the damage? Or just wipe the disk and start over?
2. I need to get my e-mail off of the hard drive. I can mount the drive after booting from a USB stick, but the thunderbird directory is locked. Is there a way around this?
Yesterday, the file system of my mp3 player went corrupt. So I tried to format it to vfat, which in the past hasn't solved the problem and instead just made another corrupt partition. I have fixed it before by using dereks boot and nuke (dban) and filling it with only zeros so its ready to be repartitioned.
Now this time I tried to save some time by using dd instead of dban.
So I did dd if=/dev/zero of/dev/sdb
The process got interrupted by my system shutting down after about 15 min.
Now when I plug in my usb, it doesn't get recognized. It doesn't show up in gparted or fdisk. I looked at dmesg and all it gave was: usb 1-4: new high speed USB device using ehci_hcd and address 5
basically the situation I'm in is someone mistakenly expanded an NAS without unmounting the drive on the server. This corrupted the superblock and its apparent that all the backups are no good. The drive in question was expanded from about 800gigs to 1.8TBs, its done via an NAS.
At this point I'm most concerned about getting the files off the drive, I can deal with resetting the file system but I really need those files. This happened within a week of me joining this group so I'm kind of doing damage control here, backups were not taken of this particular drive.
I downloaded the first Lenny DVD for amd64, wrote it but on trying the install on my laptop (Gateway NV5389u) I cant get past the installing base system step: I get an error that some files are corrupt / cannot be read from the DVD. I am wondering whether there's a way I can download a minimal version or just the files needed for the base system installation then use the same DVD to install the packages, coz I have a terribly slow internet connection it took me a whole 2 days to download, and I surely cant stand any more of it.
View 4 Replies View RelatedHave just assembled a new computer and thought I would install the 64 bit version of openSUSE 11.2 in a "Windows free zone". After a hiccup or two I have managed to get a system of sorts running but on trying to copy files from my old computer(via a memory stick) it tells me that Vfat is an unknown file system.On my old computer I am running 32 bit openSUSE 11.2 as a dual boot system with Windows XP and have no problems moving files between the two different file systems.Is it possible to get a 64 bit file system to read 32 bit file system drives and if so how do I do it?
View 7 Replies View RelatedWas I the only one having failure issues trying to install any Debian ISO Yesterday?I got big red screens about corrupt files all while trying to install Wheezy and Jessie.All with ISO versions downloaded and burned yesterday, net install. Disc and DVD.Mint and later Fedora installed perfectly well, but I wanted Debian.
View 1 Replies View RelatedAm fairly new to linux and like opensuse distro so far and determine to get it to install on my system along side my default windows OS, iva tried 11.1 and manage to get it working, however my main goal was to set it up as a development environment i.e php,java, i had to remove it later on due to certian circumstance, lastweek ive decide to try gnomelivecd 11.2 but ran into a few errors during the final stages of installment while it was Automatically Creating Configuration, with the help of oldcpu i manage to ran installation again without a black screen but this time at the same instance where the error occurs first then direct me to the failsafe screen and am stuck there ever since. Am now downloading 11.3Mildstone6 which was recommended so what am asking now is help to remove those portions,grub and restore MBR. I have tried repairing it by booting from both a winodws7 DVD and external HD but failed, the error returned was an unexpected error occurs try again. However i can boot into gnome from the live CD and Check System > Boot Loader another error popup stating that
Because Of The Partitioning, The Boot Loader Cannot Be Installed Properly.
I cleverly built a machine with two drives mirrored, boot partition on the mirror. It crashed some time when I was not present, and was apparently writing to disk at the time, for since, it will not boot. I get error messages to the effect that there is no boot partition. At this point I am not particularly concerned to try to rebuild this array, though I have read a hell of a lot on the boards about trying that (and am daunted - everyone assumes you can boot the machine with the bad array). Instead, I am wondering is it possible to build a simple machine on a third disk, then "look" at the disks in the former (?) array, and/or potentially rebuild it?
View 1 Replies View RelatedI fail to install OpenSuse 11.3 with Raid-1. What I do: Partitioning -> Expert. sda1 type RAID do not format / mount, sda2 /(root) type RAID do not format / mount, sda3 /home type RAID do not format/mount. Clone disk to sdb. Raid -> add md126p1 type swap mount to swap, add->md126p2 type etx4 mount to /(root), md126p3 type ext4 mount to /home. Bootloader: GRUB, boot from MBR enabled, boot from / disabled. After installation the system does not boot and grub reports error that the specified filesystem can not be found.
View 9 Replies View RelatedI need some information if my plan to restore Raid1 will work that way.Two Harddrives only for Data used with Raid 1 (sdb1 and sda1).
View 4 Replies View Relatedboth root and home partition have suddenly become corrupt, and the repair tool from the installation disk just loops (Do you want to repair? Yes! Do you want to repair? Yes! Do you...).
Code:
[ 54.209685] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0
[ 54.209758] ata1.00: irq_stat 0x40000008
[code]....
After installing the recent kernel update and rebooting my machine I have found a horrible fact, my computer won't boot anymore. It seems my root partition was corrupted, and running fsck on it just sends me through a endless loop of "Ignore Errors {y}:" and "Force overwrite {y}:". I have already tried the use the repair system on the installation DVD but that doesn't do anything, the pop up asking if I want to repair the file system keeps coming up when I click repair.
View 1 Replies View Relatedopensuse 11.2 64 bits installed in a RAID1 software array. Everything worked smooth during installation, the system boots, the mdx partitions are in their places, did the upgrades, configured the way i wanted, booted several times... all ok. Then i wanted to test the RAID and since its RAID1 i just disconnected 1 drive and started the computer. All what i got is
GRUB loading stage 1.5
GRUB loading, please wait...
Error 21
Connect the drive back and the system works ok.
Disconnect the other drive, then i got
GRUB loading stage 1.5
GRUB loading, pleas wait...
(hd1,0)/message: file not found
and a simple boot menu (in character mode) shows up with the 2 options SUSE LINUX and Failsafe -- SUSE LINUX (no version number)
[Code].....
I finished downloading of "openSUSE-11.1-KDE4-LiveCD-i686.iso" file. I downloaded it by Opera WB. Then using Nero I burned this file to CD. But there is a problem with boot. Please, make a support to this problem. Maybe file, which is in a site opensuse.org is damaged?
After the reboot of computer this text appears:
ISOLINUX 3.63 0x49364136 Copyright (c) 1994-2008 H. Peter Anvin
Unknown keyword in configuration file.
Unknown keyword in configuration file.
Unknown keyword in configuration file.
Unknown keyword in configuration file.
Unknown keyword in configuration file.
Loading
Invalid or corrupt kernel image.
boot:
I'm convinced that mdadm is going to be the death of me. I've wasted numerous hours on this so far without luck.
OpenSuse 11.4 on an old Supermicro box, creating a software RAID1 array across 2 x IDE 500GB disks. Creating /dev/md0 as a 250MB partition across /dev/sda1 and /dev/sdd1 for /boot, another 465GB partition across /dev/sda2 and /dev/sdd2 as an LVM partition to hold volumes for the various other OS filesystems. After the initial installation and configuration there were a series of mishaps with faulty IDE cables that had drives failing to show up at boot. Somehow, /dev/sdd2 got configured to array /dev/md1 as a spare drive. And nothing I've done so far gets it to show up as an active drive.
The obvious step of failing the partition, removing it, then adding (or re-adding) will bring it back as a spare. I've tried roughly a dozen different permutations of those same steps. The latest was to 'dd if=/dev/zero of=/dev/sdd2' to clear the partition. Thought this might be the trick - after the zero, mdadm -E /dev/sdd2 reported 'no superblock' and no md1 configuration.
So 'mdadm --add /dev/md1 /dev/sdd2' and it still comes back as a spare. Here is mdadm -D /dev/md1
/dev/md1:
Version : 1.0
Creation Time : Sat Jul 9 10:26:01 2011
Raid Level : raid1
Array Size : 488119160 (465.51 GiB 499.83 GB)
code....
I can't stop this array, the OS is running from there. I can't easily boot from CD to repair, all IDE ports have disks attached.
Does anyone have an incantation to promote a spare to active?
I just trying installing OpenSuse 11.2 on a Dell Dimension 4500 2.0 Ghz with 512 mb memory and 40 gb hard drive.During the installation the following error was produced: "System Check for partition /dev/sdb1 contains no valid Ext4 file system". After the install process was completed, the keyboard and mouse were not useable
View 7 Replies View RelatedI am so confused! I changed my security profile to 'paranoid' (i'm a linux noob' and accidentally locked my self out of everything! Including su, sudo, YaST, etc. (openSUSE 11.1)
View 9 Replies View RelatedRecently I installed openSuSE 11.3 x64 on PC with Intel motherboard, 4GB RAM & two of 1TB WD RE3.Of course I set RAID1 during installation After some struggle with GRUB which pointed to wrong devices after installation I started to work. But suddenly I found that file system is corrupted after every reboot (It does not depend on what I use and what the way I use - reboot, shutdown -r now or even just poweroff - everything follow to:
Starting MD Raid mdadm: /dev/md2 has been started with two drives
mdadm /dev/md3 has been started with 2 drives
mdadm /dev/md4 has been started with 2 drives
mdadm /dev/md5 has been started with 2 drives
[Code]...
running 11.0,Linux 2.6.25.20-0.5-paeusing a 3ware 9500 adapter - raid 5 array with hot sparethe system is only 6 weeks old.several days ago, apache would stop responding. trying a restart gives:
/etc/init.d/apache2 start
/bin/mktemp: failed to create file via template `/tmp/apache2.nb6xHyzlga2e': Read-only file system
[code]....
I can't login due to my file-system being full. I found the main area with the large usage. Var/log is taking 99.5% of my var folder. On a full file-system scan Var/log is taking up 85% of disk use. File-system capacity is 36 gig. Temp is cleared after each boot.
What can I do to clean up any unnecessary files. I can only boot in safe mode and have limited navigation skills. To get scan results I booted a live-disc.
Opensuse 11.2 gnome 64 bit.
If you have a contiguous partial piece of an ext4 file system (assuming it's perfectly clean), starting from the beginning of the partition, is there any way to check it, or to mount it to get the files whose parents, inodes and data are all completely contained inside?
Have (or maybe had) a very large 11TB RAID 6 array, filled with a single large ext4 partition. Something strange happened when a single drive failed and the array ended up failing 13 out of the 11 drives. I had trouble getting the array restarted, and got to the point where I exhausted all of the options I considered completely safe. I considered a few things that may have worked, but mdadm doesn't seem to have a definite "do not change anything" option. So I decided the only way to be absolutely safe would be to clone the disks before proceeding - then I realized how much time that would take and sent the drives off to a recovery service so they could image them and check it out.
Before doing so, I copied the first 2GB from each disk. I XORd the images from the working drives to reconstruct the data chunks that were on the failed disk, manually assembled the chunks, and am very confident that I have 22GB of "correct" data in a single file. The parity and Q syndromes all matched (with RAID 6 you can still check with only 1 missing device). I've learned the fine details of ext4 from [URL], and have looked at lots of raw data from the reconstructed partition, and it all looks good. The recovery company says that they're not finding many inodes, but I found a lot of them, exactly where they're supposed to be. I tried to mount and e2fsk, but both processes seem to be extremely unhappy that the device size doesn't match the size implied by the file system geometry.
I considered hacking the superblock to manually reduce the size, but I figure that wouldn't work because there would then be more group descriptor blocks than it would expect after the superblocks. I might try doing that and compensating by incrementing the "reserve block count" to compensate. Alternatively, if there is some way to make the file appear to be the expected size with nothing but zeroes after the end of the actual data, maybe I could mount it and not get any errors until I cause the kernel to read past the true end of the file.
I want to convert the file system on my boot drive from ext4 to btrfs.
I have converted by 2nd drive, unsure of how to convert the boot drive and partitions.
I was installing opensuse 11.2 in parallel with windows xp.but during installation suddenly power has gone and after that opensuse is giving me the error message corrupt partition.i am also not able to login in xp. so I decide to reinstall windows, I got the error saying "invalid partition table" after the first restart of windows xp installation.
I tried to use windows system recovery console and committing fixmbr and fixboot commands, but didn't work.
i have 2 window partition(1 for windows and 1 for data).i do,nt want to format 2,nd partition.
How can I installed windows?My plan was first to install windows xp, then opensuse again.
I've just purchased HP Mini 5103 with preinstaled SLED, but I want to replace with 11.3. But I have serious problem with booting from USB. Due to problem with BIOS bug/feature, 5103 is unabled to boot using USB with recursive partition (which is created from hybrid openSUSE-11.3-KDE4-LiveCD-i686.iso either with ImageWriter of dd). When I create bootable USB with syslinux and copying of iso to existing partition, I ended with error "failed to detect CD/DVD or USB drive" (I have tried also both initrdud files, older one failed with "failed to detect USB", newer with "failed to detect CD"). I have also tried to install from full openSUSE-11.3-DVD-i586.iso which I have copied to USB using Unetbootin, but with this bootable USB I ended with "invalid or corrupt kernel image".
View 7 Replies View RelatedAfter several crashes during videos it seemed like a good idea to fsck root. Downloaded the latest systemrescuecd and ran it at boot. The error message was 'bad magic number, corrupt superblock' with a suggested command to try another superblock. That failed with the same message. Tried tune2fs to force fsck at boot and got the same message. The drive is less than 6 months old and the installed system is working more or less ok. The command I used was 'fsck.ext4 /dev/sdc2'. What am I doing wrong?
View 9 Replies View RelatedToshiba notebook is set up to triple boot win7, mepis 8.5 and os 11.3.Recent update of os11.3 left system with boot failure, "file not found".I booted mepis and used utility to reinstall grub, but no joy.
Appeared to install ok but on reboot, sda5 identified as 'mepis' not os11.3 and would not boot. Win7 & mepis boot ok.
Next, booted live Parted Magic and repaired as per another thread here, but again, no joy.NONE of the systems will boot.Rebooted mepis live cd and reinstalled grub again. Sda5 still identified as mepis and will not boot. Win7 & mepis boot ok.
It started when I wanted to dual boot Windows 7 and Opensuse off of my netbook (No DVD/CD drive) I tried install suse from an external hard drive and I botched it. I ended up erasing EVERYTHING off of my internal netbook hard drive. Windows and all.
Well, I had a couple of other computers so I studied up and eventually successfully installed OpenSUSE 11.2 on my external hard drive (11.3 being the one that I accidentally erased everything with, so kinda scared of it) and now I want to install openSUSE 11.2 on my internal netbook hard drive.
I can not use disks
I can not use a flash drive (For some reason, even if I make it bootable, it will not load up, this could be because it's actually a 8GB microSD card that is placed in a USB card reader.)
I can not use an external hard drive because that's what I'm running suse off of.
I've tried reading up on how to install suse on another drive off of the hard drive and I've gotten as far as whenever I boot up the netbook with the suse external hard drive connected it will ask to boot into OpenSUSE, the Fail Safe, or to install OpenSuse. When I select to install it it gives me the Error 18 Unknown File system.
I've tried formatting the internal hard drive twice. One as NTFS and again as EXT4. Neither seems to effect it other than when it's ext4 I can open it and it contains a Lost and Found folder.
When I interrupt the boot sequence by pressing c and going to the terminal and I use the root (hd +TAB command it tells me I have a hd0 and a hd1. The hd1 only has 1 partition which is ext4, which I'm assuming hd1 is the internal hard drive (I'm not sure how to check) and the hd0 is the external hard drive, which has three partitions. One with an unknown file system and two with ext4. When I try to enter the set up from the terminal it gives me the same error for any thing I put it (e.g. root (hd0,0) gives the same error as root (hd0,1), or root (hd0,2) and root (hd1,0)
Something like it cannot locate these two files I'm assuming it needs to boot. If anyone finds this relevant I'll retry it and post the files its missing.
I've been searching for awhile and can't find any threads that can solve my problem. From other threads, however, I have noticed that I should probably include my menu.lst, listed below
Code:
I have also ran the boot info script and received the RESULTS.txt file it generates. Listed below
Code: