OpenSUSE Install :: DPT PM3334UW RAID Device Driver Available?
Aug 14, 2010
I am hoping there is somebody out there who might recall DPT hardware and be able to get it to work under Linux. DPT were bought up by Adaptec but made great SCSI cards. The PM3334UW is a true hardware raid device which I have been using in SOHO environment for the last 7 years or so with IBM Warp 4.52 (MCP2). The box, although legacy hardware is sound and I wish to keep it running but hoped to have an openSUSE option. Unfortunately I cannot find a driver for the SCSI RAID card. There are a good deal of posts concerning eata_dma.c and other eata based drivers as possibles but when I load the eata driver that is available when loading openSUSE 11.3 I am asked for parameters and I haven't a clue what these should be.
View 4 Replies
ADVERTISEMENT
Feb 11, 2010
I just installed SUSE 11.2 as dual-boot with WinXP on an older system that has a 160GB PATA drive and a 500GB SATA RAID drive. I left about 80GB on the PATA drive unpartitioned to accommodate SUSE. During the initial installation attempt, SUSE was determined to install on the RAID drive instead of the PATA drive, so I disabled the SATA drivers in the BIOS to force the installation on the PATA drive. This was successful, but now there is no access to the RAID drive from SUSE because there is no driver and it is not mounted. I reactivated the SATA drivers in the BIOS and the RAID drive reappeared in WinXP with everything intact. The SATA drives now appear in SUSE under Hardware Information as "/dev/sdb" and "/dev/sdc" and the listed driver is "sata_sil".
So how do I get the RAID drivers installed in SUSE and then mount the drive so it can be browsed/modified from Dolphin? I would also like to be able to browse/change this drive from other computers on my home network through samba, just like with WinXP.
View 9 Replies
View Related
Feb 28, 2011
If I have a windows installed in raid-0, then install virtualbox and install all my linux os,s to virtualbox will they be a raid-0 install without needing to install raid drivers?
View 1 Replies
View Related
Feb 13, 2010
Short story: Correct driver for 10.1 for the raid on the Intel S3000AH board?
Long story: This system crashed due (I think) to a bad memory module, had been running fine for 2 years, had been an upgrade from Suse9. The hardware is fixed but I get "GRUB" repeating on the screen when booting and that is all. I can't seem to find opensuse drivers for 10.1 (that is what I believe is on the system, I believe the data is still intact and don't want to compromise it if possible) It will not load the 10.1 drivers from the intel site, presumably (?) because they are for SLES, not opensuse. I can boot from a 9.3 CD with the drivers from the intel site, and can see the original partitions.
View 1 Replies
View Related
Mar 7, 2011
When you see this topic we are in trouble of installing driver of the raid card on hp server.
Enviorment:
OS: Slackware 13.1
Server Type : HP ProLiant DL160 G6
Raid Card: Smart Array B110i SATA RAID
Disk : SATA 250G * 2
Raid Model: Raid 1
We have setted raid model (raid 1+0) in BIOS and when we finished install Slackware13.1 ,the OS can not recognise the raid disk(also two disk).Is there anybody can help me?Some solution or driver program or other infomation etc.My email is "feng.pan@continental-corporation.com".
View 2 Replies
View Related
Jul 27, 2009
Currently I am attempting to install Centos 5.2 64bit onto a Supermicro X7DCL-3 motherboard based machine. The Raid recognizes the HDD that's been installed into it, however, the drivers for the raid are not included in the install. After contacting Supermicro I've been supplied with a driver package that should fix the problem.[URL]However, I am still having trouble using the package in order to find the HDD (The only HDD in the machine) that is on the raid.I think I'm doing something that's should be fairly simple, but am screwing it up pretty bad.
View 1 Replies
View Related
Jan 12, 2009
Installing new Intel server S5000VSA (Sapello) motherboard with RAID 1. Downloaded F10 32 bit DVD and run install. Everything works fine and select Samba and all that. Install completes but on reboot get a blank screen.
I know with Windows one has to load the RAID driver off the Intel driver CD, so guess that is the problem. But how do I do this in Fedora? Question: How do I get to select the Intel RAID driver in the install process? There does not seem to be any place to stop and make this selection. I tried selecting the Red Hat and Suze installs on the Intel configuration assistant but it then reboots and that is it. In Windows it would ask to insert the Intel driver CD but that does not happen. So I am stuck. I loaded Fedora some 3 year ago and like it but then it was not on a RAID setup. I created a VMWare install on my desktop and did the same install options and it works. So the DVD seems fine.
View 3 Replies
View Related
Jan 8, 2010
how to detect and install a mic device driver? i only plug and play the mic in xp.
View 1 Replies
View Related
Feb 2, 2010
How do you find out which driver is being used for a certain device. Say that I run lsusb and I find "Bus 007 Device 002: ID 046d:c043 Logitech, Inc. MX320/MX400 Laser Mouse", how can I find out what the active driver for the device is?Also, is there some way to list all available drivers for a device? Is there a way to change the driver at runtime?
View 1 Replies
View Related
Jun 4, 2011
Fedora is having trouble identifying a raid partition, it sees them as separate drives. I got drivers from dell, but during a Fedora dvd install, it mentions nothing about a place to install extra drivers.
When it says it must "initialize" the drives, Fedora then breaks the dell bios raid. How to either install the dell drivers or make Fedora see the raid partition as one?
View 1 Replies
View Related
Sep 15, 2010
It's been a real battle, but I am getting close.I won't go into all the details of the fight that I have had, but I've almost made it to the finish line. Here is the set up. ASUS Z8PE-D18 mother board 2 CPU, 8 Gig Ram. I recently added an OCZ Agility SSD, defined a raid 1 virtual disk on the 1 terabyte WD HDD drives, which will holds all of my user data, the SSD is for executables.The bios is set to AHCI. Windows 7 installed fine, recognizes the raid VD just fine.
I installed Ubuntu 10.04 by first booting into try and mode, then opening a terminal and issuing a "sudo dmraid -ay" command. Then performing the install. I told it to install the raid components, and told it to let me specify the partitions manually. When setting up the partitions, I told it to use the free space I set aside on the SSD from the Windows 7 install as ext4 and to mount root there. Ubuntu installed just fine, grub2 comes up just fine, and Windows 7 boots with out a hitch, recognizing the mirrored partition as I indicated previously. When I tell grub to boot linux however, it pauses and I get the "no block devices found" message. It will then boot, but it does not recognize the raid array. After Ubuntu starts up I can run "dmraid -ay" and it recognizes the raid array, but shows the two component disks of the raid array as well. It will not allow the component disks to be mounted, but they show up which is annoying. (I can live with that if I have to)
I have fixed a similar problem before by setting up a dmraid script in /etc/initramfs-tools/scripts/local-top ... following the instructions found at the bottom of this blog:[URL].. To recap: My problem is that after grub2 fires up Ubuntu 10.04.1 LTS (Lucid Lynx), it pauses, and I get "no block devices found" It then boots but does not recognize the raid array untill I manually run "dmraid -ay". I've hunted around for what to do but I have not found anything. It may be some timing issue or something, but I am so tired of beating my head against this wall.
View 4 Replies
View Related
Sep 19, 2009
I am currently using fedora 11 kernel 2.6.29 version, i wanted to write device driver for usb to detect my own device. My project is radio with computer. My fm radio get connected to usb port so i need to write h/w interfacing program.
View 1 Replies
View Related
Nov 10, 2010
The error "USB device 6 (vend/prod 0x603/0xf2) is not claimed by any active driver." is in dmesg every time I connect my Logitech keyboard to my system. I also tried (all with the same error):
- Memory stick
- DVD-burner
- Compaq mouse
View 3 Replies
View Related
Jul 28, 2010
I have installed live cd on usb pendrive. Everything works great. How can I find out which device driver it is using? Where are the device driver files stored? How do you specify the device driver when mounting a device?
View 3 Replies
View Related
Jul 20, 2010
I cannot install 11.3 on a machine with an intel raid controller I have tried with raid 1 using the card and then setting the disks to individual raid 0 and letting suse raid them. With the card doing it the machines crashes as soon as it tries to boot the first time, with suse doing the raid I just get 'GRUB' on the screen It seems a lot of people are having similar problems, does any one have any pointers. 11.2 installs fine. I would try and do a bug report but every time I go to the page it's in Czech
View 4 Replies
View Related
Dec 14, 2009
I have got a mid-aged server which i upgraded with a simple SATA-Raid-Controller with a VT6421A chipset.I attached two Samsung 750 GB Hard disks and created directly after the POSt screen a nice Raid 1 array. Ubuntu will recognize it as well as windows (which I would never ever use... ;-)).SuSE 11.1 (we need this OS for confirmity) will simply just recognize both disks in the partitions overview. The point "RAID" remains empty.
Are there any hints out there how I can enable the whole raid stuff in open suse? Do I need to integrate other drivers / modules to get thinks working?
View 3 Replies
View Related
Feb 5, 2010
A friend of mine gave me an old Dell PowerEdge SC 1430 Tower Server. It has three hard-drives in it, that are about 160 GB each. The system had a Promise FastTrak TX1430 Raid card in it, and I am not sure. Would that be a hardware RAID, or would you consider that a BIOS Raid?In any event, have the very latest OpenSuse 11.2 install DVD.I can boot from the DVD, do a fresh install and the system starts where I can sign on as the user. When I look at the starting parition, it has /dev/sda /dev/sdb and /dev/sdc ... each being a hard drive. These are just listed under the hard-drives, not under RAID.
The problem is that when I cold shut-down the machine, and restart from a power-up, the system comes up and cannot find the boot disk. So, Obviously I am doing something wrong.I am used to having 1 or 2 drives in a machine, just SATA drives, and no raid at all. I have no experience installing Linux on a machine with RAID, again not sure if this is BIOS or Hardware RAID.
View 4 Replies
View Related
May 17, 2010
Now that I set up a 4x750GB OnBoard RAID 10, I'd like to install my 11.2 Suse (w/ GRUB dual boot)from BIOS, I've partitioned my HDD so I have:- Array1 = 30GB HTFS, 30GB XFS, 30GB Solaris, then extended part. for all (each OS) swap, temp, etc ...- Array2 = 30 GB HTFS (DMy Documents); 30 GB (/home); 30 GB (unformated) and then a big part for game install and VMware partition (Win98 for my old games, winXP32, etc ...)As a (sad) matter of fact, instal WinXP64 and/or Vista64 works perfectly. I see the array as partitioned by BIOS, and everything works.
But I can't have my 11.2 (64) SUSE installed on the drive, I have -for now- a VMware for it running ... on Windows :s(while I'd prefere the opposit)When I start w/ Suse11.2 DVD (downloaded), it says it can't install as there is NO HDD !!ok, fine, I plug back a PATA HDD, then I start the install, then I move the partition to the SATABUT, even so, I can't start the Suse ...I then lauch the repare/recovery on the install DVD, but it says that there is no root partition, no SUSE partition to fixe
View 9 Replies
View Related
Jun 9, 2011
After an install of suse 11.4, one of my drives raid 0 (ichr9 intel) does not mount and is not recognized as being formatted in NTSF, while the other unit raid 0 (ichr9) is recognized without problems?
View 4 Replies
View Related
Apr 6, 2010
I'm having some (well, a lot actually) of problems trying to get OpenSUSE 11.2 installed on my home PC. I am attempting to set up a dual boot configuration with Windows 7 installed on an bios Nvidia RAID 0.I was able to shrink the partition in Windows, and rebooted onto the net install for OpenSUSE (the MD5 validated DVD install failed multiple burns with "Repository not found"). I get into the graphical installer portion with no problems off the net install CD. However, the installer is not recognizing that there is an existing RAID 0. It lists the 2 SATA disks in the RAID separately. I can click on SDA1, and both SDB and SDB1 and it shows the disks, but does not recognize any existing partitions. If I click on SDA I get an immediate segfault in YaST and drop back to the text mode installer menu. It is loading the nv_sata module just fine.
From forum searches and google it seems that this is not usually a problem. My motherboard is a Gigabyte GA-M57SLI-S4 with the Nvidia Nforce 570 chipset running an AMD X2 64 3800+. Removing the stripeset and redoing it as Linux software RAID is not an option, I do not have enough space for a total backup/restore. Anything I do has to be nondestructive to the existing Windows installation.I really want to have a linux installation but between the DVD installer failing and now this issue I am about ready to give up on it.
View 9 Replies
View Related
Jun 19, 2010
I installed OpenSuSe 11.2 x64 on my PC.It's not work will:After installation, the system auto login KDE GUI.but when I reboot(or shutdown and open) my computer. Message on screen meaning:"can't find bootable partition".My PC's hardwareMother Board: DFI 790FXB-M3H5(South Bridge: SB750)Hard Disk: WD 500G*2 Raid 0(via SB750 Chip function)Oh, I'm sorry, It's Fakeraid, not hardraid.
View 9 Replies
View Related
Jun 25, 2010
I've got 3 extra disks on OpenSuse 11.2 - all the same size. I've created a partition on all of them as type 0xFD. If I then try and add raid in yast I get "There are not enough suitable unused devices to create a RAID."
View 9 Replies
View Related
Feb 3, 2011
I have got a server which has a motherboard with nvidia mediashield raid built in, with Centos installed it picked up the raid 5 array that i had configured as one drive so the os install was straight forward. When i booted the netinstaller of opensuse 11.3 run though the setup, when getting to the partition setup is was picking up the three hdd as seperate drives and not one, so i got to a certain point and aborted the installation and i re run the installer, the raid status said the array was degarded or something which i knew there was nothing wrong with it as i had set it up only about 2 weeks ago and there was one drive missing aswell. So i removed the array and re configured the array and rebooted and the raid status said healthy again as it was before on centos, then i run the opensuse installer again and it went though the process again but completely stop at "Searching for linux partitions" , cursor was working fine , but nothing else was so i had to press reset.
This was my problem, i know kind of what the problem is, but what i want to know is , i thought opensuse is based on rhel same as centos but how comes centos has the drivers for the raid chip i have in my board and opensuse has not.
View 5 Replies
View Related
Mar 16, 2011
I'm trying to reassemble a broken raid 5 array. The array has 3 drives. Here is some output from 'mdadm --examine': hutch:/home/sam # mdadm --examine /dev/sdb1 /dev/sdb1: - [URL]
View 1 Replies
View Related
Aug 11, 2011
I want to install opensuse on a poweredge 830 server with a cerc 1.5/6 hardware raid configuration, since i have no previous experience with linux I'm having a hard time to grasp the way to do things. But i would love if someone can direct me to a good tutorial or document where i can learn more. At this moment I'm stuck (though i decided to install using default options yast gave me, just to test) with partitioning and RAID.
So this is what i would like to know:
Conditions:
*Server currently has a windows 2003 installed but I don't need it so actually that is going to go away
*this is a small network, less than 30 users
*Server is going to be used to authentificate users through openldap, also is going to serve files (since we do printing many of them would be 100mb +), and also depending on performance may be used as printing server too (i know that's a lot of tasks but besides printing other functions won't be used that much)
*Server has 2 phisical HD that i want to use with RAID 5 or 6 there are drivers for that already in dell's webpage
* I'm installing openSUSE 11.4
Questions
1.- Does linux really needs a dedicated swap partition
2.- If so how raid works with that, is it going to be mirrored too (I don't think)
3.- Is it better to install linux in 1 HD only with no swap partition, leave the other blank and install raid after linux is up
4.- What's up with ext units, in the sense that now it looks like there are too many units.. not only the simple 'os, data' i'm used to
Objective
1.- I just want to have a linux installation with raid 5 configuration using 2 hd
View 5 Replies
View Related
Jan 16, 2010
I have three WD 1.5 GB harddrives. 2 of them already in a linear RAID also called Concatenated i think. (the same as JBOD). Can i add the third drive to the RAID without losing data? Update "Using mdadm software raid."
View 7 Replies
View Related
Mar 14, 2010
I look after some small office where computers run ubuntu. Sometimes they phone me for help. For that reason, I decided to install ubuntu alongside with my slack.I seem to have problems with lilo configuration. Ubuntu is installed on software raid :
/boot = md0 (raid 1 of sda1+sdb1)
/ = md1 (raid 0 of sda2+sdb2)
That's lilo.conf:
Code:
append=" vt.default_uft8=0"
boot = /dev/sda
bitmap = /boot/slack.bmp
[code]....
Code:
Fatal: open /vmlinuz-2.6.31-9-rt: No such file or directory
I can mount md0 without problems and the file name seems to be correct.
View 3 Replies
View Related
Jul 13, 2010
I built a new pc and want to have Suse again. Unfortunately Suse installation does not recognize my CD/DVD device. So I boot from DVD select installation and a few moments later there's a popup 'make sure cd number 1 is in your drive'. I also did try to load other kernel modules but nothing helps. The only drive which is always recognized is floppy drive.
Here are some details about my system: Asrock P55M Pro board, Intel P55 chipset, 2 SATA HDD's, IDE NEC 2510 DVD writer, BIOS is set to AHCI due to Windows.
I tried following:
Use Suse DVD 11.0, 11.2, x86 or x64
Set BIOS to AHCI, IDE (compatible), IDE (enhanced)
DVD writer NEC was used in my former pc and did install 11.0 without probs.
Installing from HDD is new to 11.2 thus I copied the DVD to a directory. During Installation I can select the correct partition but suse is not able to find repositories.(?)
View 9 Replies
View Related
Jan 27, 2010
I'm having some problems with a hosted openSUSE 11.2 server. It was running fine until I did a "zypper up" to apply patches. This included a kernel update.
On reboot the root partition does not mount the / partition giving the following error:
Unrecognized mount option "defaults.noatime", or missing value mount: wrong fs type, bad option, bad superblock on /dev/md2.
Through an Ubuntu rescue disk (this is what Hetzner provides) the disk can be mounted without problems.
( I installed a fresh openSUSE 11.2 with a similar configuration and got the same results after the update)
The server is a hosted installation from Hetzner in Germany with just the basics for LAMP setup.
The disk setup is as follows using software raid1:
swap /dev/md0 (/dev/sda1 /dev/sdb1)
/boot /dev/md1 (/dev/sda2 /dev/sdb2)
/ /dev/md2 (/dev/sda3 /dev/sdb3)
View 3 Replies
View Related
Feb 27, 2010
I'll have a Sony VAIO AR290 with 2 HDD, earlier I'll have a Windows XP and SUSE and RAID was turned off. Now I turn on RAID in STRIPE mode for better productivity, Windows 7 installation was successful, It creates MBR partition (100 M and C: HDD. During SUSE installation(I've chose all parameters- swap and partition) installation process stop at 1% on "operating with HDD" and my VAIO dont answer on any key pressed (alt ctr del, ctr c, esc) and I'll should to turn it power off. During surfing web, I'll find some solutions to solve it by creating root partition but It hasn't any results.
View 7 Replies
View Related
