I'm trying to reassemble a broken raid 5 array. The array has 3 drives. Here is some output from 'mdadm --examine': hutch:/home/sam # mdadm --examine /dev/sdb1 /dev/sdb1: - [URL]
View 1 RepliesI installed RC1, and never touched the disks that were raided previously, and the attached image is what i see for my raid array that was previously working fine.
View 3 Replies View RelatedI have an issue with a RAID array failing on boot. Seems like an issue with the file system. I get passed the RAID BIOS (and from what I can see, it looks alright there, all devices appear), but then the following error messages appear:
Code:
raid5: failed to run raid set md0
mdadm: failed to RUN_ARRAY /dev/md0 input/output error
mdadm: Not enough devices to start the array
and further down:
Code:
fsck.ext3: Invalid argument when trying to open /dev/md0
/dev/md0:
The superblock could not be read or does not describe a correct ext2
[code]....
I then login with root password to get a "Repair file system" prompt. Tried with fsck, but not working. It's 4x1TB in RAID5 on HighPoint RocketRAID 2300 4P SATA II/300, with Fedora 9. Not sure what other system info might be needed.
One of my raid disks (was a software raid5 with 4 drives) failured. I wanted to buy a new 1.5TB harddisk anyway so i i copied all the Raid data onto the new disk and disconnected the old ones. But then the new Disc crashed right before i could mirror it with another 1.5TB disk. So i need to reassemble my old Raid 5 now. I connected the drives in the former order except the first one, because this was the failed disk. The problem is, mdadm can't find the raid, no superblocks. Fdisk doesnt show mdraid superblocks, too. But fdisk has never showed superblocks. The thing is, this raid was crypted, but i crypted the /dev/md0, so this doesn't affect anything here, or?
some infos:
Code:
server:~# mdadm --misc -d /dev/sda
mdadm: option -d not valid in misc mode
server:~# mdadm --misc -t /dev/sda
[code]....
Disk /dev/sdc doesn't contain a valid partition table But fdisk always said there is no valid partition table and the raid was working.
I have a NETGEAR ReadyNAS NV+ with four 1TB drives in a RAID-5 array. This is our primary file storage. This has previously been backed up to a hardware RAID-0 array directly attached to our Windows server. The capacity of this backup array is no longer sufficient. So the plan was, take a bunch of 200GB to 320GB drives (And a 750) I had kicking around, chuck them in a couple of old SCSI drive enclosures I have collecting dust, attach them via IDA/SATA-to-USB adaptors to a USB hub, attach that to the server, create a JBOD array spanning the disks, and back up the NAS to that. Performance is not an issue as this is just to be used for backup, with the idea being as near to zero cost as possible (Spend so far = NZ$100�ish).
The first hurdle I struck was Windows not supporting Dynamic Disks on USB drives (Required to create a spanned volume). At first I resisted using another machine (i.e. a machine running Ubuntu) as I didn't want to dedicate a piece of hardware to backing up the NAS. I then decided it would be acceptable to do this via a VM, which is what I've done.So I have 10.04 running under VMWare Server 2.0.2 under Windows Server 2008 R2. The disks are all presented to the VM. I wasn't sure if I was going to end up creating the array under LVM or something else, but I noticed Disk Utility has an option to create an array, so I tried that. When I add two 250GB drives, the array size is 500GB. When I then add a 160GB drive, the array size drops to 480GB. Huh? If I keep adding disks (Regardless of order) the final array size comes out at 1.8 TB, as per the attached screenshot. Now with the following drives, I expected something more like:
160 + 250 + 250+ 750 + 250 +200 + 200 + 250 + 320 + 250 + 320 = 3.2TB
Am I missing something or making a false assumption somewhere?
I recognize that this isn't the typical question, but I have a problem with my OpenSUSE webserver, and I thought I would prevail on the community for some guidance. I have this webserver with an important MySQL db on it. The RAID array seems to have died while I was moving. (did someone drop it? dunno) Now it can't find any boot device. It has 4 old SCSI drives.
So, I know how to mount a IDE or SATA drive as a slave, in a Linux environment to read data off of it (to copy the MySQL files off of it.) But, how do I do that with a SCSI drive? Also, I have an additional (identical) server to the crippled one. What will happen if I just slide one of the scsi drives into the operating server? Is this second identical server going to help me at all? I don't even know what is on it. Can I reconfigure the RAID, so it's not using a drive, and then slide in a disk from the crippled server, and copy the data off of it?
I'm having issues with a RAID array.
Setup is like this:
Debian Jessie, 2 hard disks, each having 2 partitions: /dev/sda1, /dev/sda2, /dev/sdb1, /dev/sdb2. Partitions were paired during installation, so they form /dev/md0 and /dev/md1. /dev/md0 is the root (/) partition, /dev/md1 is for /home.
At the end of the install process, I chose /dev/sda1 to carry Grub. And I think this is where I screwed things up.
After removing one of the hard drives, there was no boot capability. So, I installed Grub on /dev/sdb, too.
Now it displays the boot menu but cannot find the kernel. This is where I got lost in the process.
Do I need to reinstall the OS or is there a way to fix it? I suppose I have to edit Grub.
I'm trying to switch to a new RAID5 array but can't get it to boot. My disks:/dev/sda: new RAID member
/dev/sdb: Windows disk
/dev/sdc: new RAID member
/dev/sdd: old disk, currently using /dev/sdd3 as /
The RAID array is /dev/md0, which is comprised of /dev/sda1 and /dev/sdc1. I have copied the contents of /dev/sdd3 to /dev/md0, and can mount /dev/md0 and chroot into it. I did this:
Code:
sudo mount /dev/md0 /mnt/raid
sudo mount --bind /dev /mnt/raid/dev
sudo mount --bind /proc /mnt/raid/proc
[code]....
This completes with no errors, and /boot/grub/grub.cfg looks correct[EDIT: No it doesn't. It has root='(md/0)' instead of root='(md0)']. For example, here's the first entry:
Code:
### BEGIN /etc/grub.d/10_linux ###
menuentry 'Ubuntu, with Linux 2.6.35-25-generic' --class ubuntu --class gnu-linu
x --class gnu --class os {
[code]....
However, when I try to boot from /dev/sda, I get:
Code:
error: file not found
grub rescue>
I'm about to install Ubuntu on two 250-gigabyte hard drives in a RAID 1 array, but I'm confused about how to partition my hard drives. How much space should I give to each partition? How many partitions should I create and where should I mount them? (I should mention that Ubuntu will be the only OS on this array.)
View 3 Replies View RelatedI've tried to install Fedora 11, both 32 and 64 on my main machine.It could not install as it stops on the first install window. I've already filed a bug but really haven't seen any feed back yet.The bug has something to do with Anaconda and the Raid array but I really can't tell.
I have an Intel Board (see signature). I am running intel raid software under W7 currently.It works fine. But, I'm wondering, when I attempt to install F!!, is my current raid set-up causing problems? Do I need to get rid of the intel raid software and use a Fedor/Linux raid program to manage the raid array??
Consider the following setup: Ubuntu system installed on a separate SSD for speed. An ubuntu software RAID array consisting of X number of physical HDD's for storage (RAID6 or RAID10). RAID setup is done during system install. If I suffer a total crash of the SSD and loose my system, will I be able to, using a new system disk, "reconnect" to the RAID array even if the "mothersystem" of the software RAID is lost? If yes, are there any particular config- or system files I need to backup to be able to rescue the array or will it just be recognized "out-of-the-box" when reinstalling ubuntu?
View 4 Replies View RelatedI am using Ubuntu 10.04 x64. I am not trying to install Ubuntu on a RAID 1 drive like all of the guides are for. I have a RAID 1 array that I am using for data storage. In windows it shows as a single array just fine. In linux it shows as 2 separate drives. I don't care how they show up to be honest I just have to data written to one drive written to the other automatically as well so my RAID isn't screwed up. Looking through different articles and forums I find a lot of stuff saying that it should show up under /dev/mapper/dxxx or something under /dev/mapper. All that shows up there for me is a device called control which doesn't seem to do something.
View 1 Replies View RelatedI just installed Ubuntu 10.10 64bit and wanted to get access to my nvidia RAID array. This array is working, and is NTFS formatted. But wasn't showing up through normal means in Ubuntu. (for example the NTFS Configuration Tool didn't display it) Here's what the system showed.
Code:
root@hermes:~# ls -l /dev/mapper/
total 0
crw------- 1 root root 10, 59 2010-11-03 22:39 control
lrwxrwxrwx 1 root root 7 2010-11-03 22:42 nvidia_dadijiag -> ../dm-0
[code]....
Is my mirror still in effect, or did i just mount one of the specific drives from the mirror?
I'm going a little bit crazy. I can't seem to remove my RAID 1 arrays. Any suggestions? I don't need to save data. The drives are empty. I'm upgrading to 4 2TB drives.Running Lucid Lynx server
Code:
jessica@nas:~$ cat /proc/mdstat
Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10]
md2 : active raid1 sdb1[1]
976759936 blocks [2/1] [_U]
md0 : active raid1 sdd1[0]
[Code]...
i am trying to increase raid1 arraysize whcih is predefind,what i did i add two more drive in the raid but i could not increase raid array
exp:-
Creation Time : Wed Feb 2 18:14:56 2011
Raid Level : raid1
[code]....
Round two:I am trying to install a RAID 1 array on my system. I already have another RAID 1 array in there. I am using the BIOS RAID option to set up the array.Here's what dmraid -r tells me:
# dmraid -r
/dev/sda: pdc, "pdc_bajfedfacg", mirror, ok, 3906249984 sectors, data@ 0
/dev/sdb: pdc, "pdc_bajfedfacg", mirror, ok, 3906249984 sectors, data@ 0
[code]....
I am currently running all my applications off a HD as I was unable to install the grub bootloader on my ocz pci express card (grub won't install on the pci express card as it is a raid0 array). I would like to use the HD for backup only and run everything off the ocz card - with the exception of booting (which is unfortunate but I didn't manage to make the pci express card boot). How is it possible to tell suse during the installation to create the /boot on the HD and the rest on the pci express card and also to allocate the remainder of the HD as empty storage area??
View 1 Replies View RelatedI installed Debian 5.0.3 (Backport with .34 Kernel), because my server hardware (Dell PowerEdge R210) needs special firmware and drivers.However, the installation went quite smooth.I put the system on a RAID 1 Array with about 500 GB space.s I said the installation went well, however, it doesn't boot! No GRUB, nothing
View 4 Replies View RelatedJust setup with Debian 8 (LXDE) a few weeks ago. Raid10 array was preexisting.
Was working well. After booting I would need to go to the save as then would need to enter the root password and everything would be good.
Can't access the array.
Used to use the command $ mount /dev/dm-o /home/myspace/folder under Debian 7.6 to mount the array (no longer works).
blkd lists a /dev/md0 but instead of UUID it is PTUUID
[Code] .....
I want to make a RAID5 array with 4 2TB hard drives. One of the drives is full of data so I will need to start with a 3 disks and then once I copy the data from the 4th onto the array, I will then add the 4th drive. This will be my first experience with RAID. I've spent a few hours searching for info but most of what I have found is a bit over my head.
View 9 Replies View RelatedI'm just about to be given a Power Mac G5 (Late 2005) Dual 2.0GHz. I think this was the last G5 produced.I plan on using it as file server/NAS and will probably run 10.04 LTS (or maybe 8.04 LTS). I would install a SATA RAID controller and run 4 1TB drives in a RAID 5 configuration. The only thing I'm unsure about is choosing a compatible RAID controller. I need to find a RAID controller that
- Is PCIe
- Is compatible with both the Power Mac and Ubuntu PPC
- Does true hardware RAID
- Doesn't cost a fortune!
Am I right in thinking that the card might need to be open firmware compatible? If it makes any difference, I plan on running the OS from a separate 5th drive. I've found this on eBay. I asked the seller and he claims it supports true hardware RAID and says the chipset is a Silicon Image SIL3124. I does seem suspiciously cheap though...
After upgrading my ubuntu install my raid array is gone. The drives appear in blkid as "Linux raid member" and both have the same uuid. If I try to mount the drive via fstab I get a message that the drive is not ready or present. If I try to mount each of the two drives, one mounts successfully the other reports serious errors. Issuing a cat /proc/mdstat shows md_d0 as inactive.How can I re-establish my raid array? I have the data backed up so if I have to wipe out the disks to start over that's an option.
View 2 Replies View RelatedI currently have a nice HTPC setup that has been upgraded from distribution to distribution since 8.xx all the way up to 9.10 now. I just moved to a new place and it feels like the right time to do a fresh install of 10.04 into the HTPC. The problem is that I have a RAID 5 array in the system that has all my pictures, videos, music, etc. This OS is installed in a separate drive that is not part of the RAID array (I have 4 drives in the system, 3 in the array, 1 for the OS). what is the general process I should follow to do:
1. a fresh install of 10.04
2. do #1 while at the same time not losing my array (don't think I would anyway).
3. what to do after install to get the array back up and running and mounted.
I am using the 10.04.1 x64 Kubuntu live CD to install Kubuntu on my FakeRAID 0 array, I tell it not to install grub as i know it is still currently broken. the install goes flawlessly. However on first boot using my live grub CD unless i tell my computer to point to the CD it will hang (which it is told to boot from CD first so i'm not sure why it does.) When i tell it to boot to Linux, it will not boot saying the kernel is missing files (to much to sadly list, all i do not understand) then offers me a terminal to input "help" into for a list of Linux commands. Windows 7 pro x64 works just fine CD was downloaded VIA P2P if it matters
View 6 Replies View Relatedrepairing the MBR on my raid array. I have three disks, each with three paritions:root (sda1 sdb1 sdc1) 59GB swap (sda2 sdb2 sdc2) 1.12GB grub/boot (sda3 sdb3 sdc3) 298MB I have been able to get this running and it has been working fine for several months. A few days ago, I installed 10.04 to a USB stick but did not disable the hard drives at that point and so the MBR was overwritten. If I leave the USB stick in, it boots fine from that stick. However now I can't get the boot from the raid array to work correctly. I can do the following:Load 10.04 from the Live CD install mdadm recreate the root partition using
Code:
mdadm --assemble /dev/md0 /dev/sda1 /dev/sdb1 /dev/sdc1
I can mount and view the files on md0 with no problems. It's not corrupted in any way. When I installed, I followed the directions to make each of the grub drives bootable. However I don't know for sure whether grub was installed on each partition separately or if it was installed on the assembled partition only. I have tried using
Code:
sudo grub-install /dev/sda3
and got warnings, something to the effect
Code:
Cannot find a device for /boot/grub
no path or device specified
Auto-detection of a filesystem module failed
specify the module with option '--module' explicitly
I have also been able to get to the grub rescue prompt but my keyboard (wireless USB) is not recognized and so I can't type anything in at that point.
I've created a soft raid w/ 2x 1TB drives by using Disk Utility. (used for mythtv storage, not system, swap or anything else)
If I start the raid array in the Disk Utility mount and everything works as it should, but on reboot the raid array isn't started so I have to go into Disk Utility, start it, then run the mount.
How can I get it to start automatically?
I have acquired a dell 2850 poweredge server and installed ubuntu server onto only to find out we cant use linux for its intended use and need to uninstall remove ubuntu and it has a raid 5 array on the server.
View 1 Replies View RelatedI have an Areca hardware RAID array that I'm trying to format & partition on a fresh Ubuntu 10.04 LTS installation. The OS drive is not on the RAID card, it's entirely separate. The RAID is a 6TB volume so I realize I have to use parted to format it, not fdisk (which I've always relied on).
My problem is that I can't figure out how to get parted to like my settings. It seems like everything I try gives me the warning "Warning: The resulting partition is not properly aligned for best performance." Here's what I'm doing:
Code:
(parted) p
Model: Areca ARC-1280-VOL#00 (scsi)[code].....
What start/end settings should I use to get a properly aligned partition? How do I know?I have tried a mix and match of 0, 0s, 1, 1s, -0, -0s, -1, -1s, 100% for my start/end with no success.
I had some issues with my RAID6 array (with 15 disks), where 5 disks got disconnected (each five disks is connected to the motherboard via 1 SATA cable), which brought down the RAID array. I fixed this problem via readding the disks and running the array:
Code:
mdadm -R /dev/md1
However, after rebooting, the array appears inactive, and I have to go through the same motions to fix this and make it active.
The array is present in the /etc/mdadm/mdadm.conf, though also 2 other raid arrays (3 arrays total):
Code:
DEVICE partitions
# auto-create devices with Debian standard permissions
CREATE owner=root group=disk mode=0660 auto=yes
[code]...
I'm running a Debian homeserver, with a 3-disk (1GB each) raid 5 array using mdadm (the OS is on a separate disk).Now, smartmontools noticed some bad sectors on one of the disks, and I'm not sure what to do next (except for backup of valuable data).I found some articles on how to fix these sectors, but I'm unaware what the result on the whole array will be.
View 4 Replies View Related