i just installed opensuse yesterday and it's very nice. i wanted to install the driver for my ati mobility radeon hd 5470, so i followed the steps on:SDB:ATI drivers - openSUSEunfortunately, after the reboot, opensuse had booted but there was nothing on my screen (basically, just a blank screen)
View 7 Repliesi have just put a Geforce 7300 GT graphic card into my machine the problem is the max resolution I can get is 1024x768 at 60 hz the screen is a benq fp71g+. also the screen goes blank when i click on the display icon in system settings. i know that the screen can be run at 1280x1024 so I don?t know where the problem is.
View 3 Replies View Relatedi just installed opensuse 11.4 on my system(gigabyte 7n400pro2,amd athlon xp 2.8ghz,ocz vertex2 ssd,ati radeon x1550) and i have this strange problem: the screen gets blank(for about a second) every 40-50seconds. everything else works fine.
View 5 Replies View RelatedA surprising thing has happened! I have been happily using open suse 11.3 on an HP probook 4320s laptop. On reboot this morning, the screen starts out fine, but progressively fades into white and the boot does not seem to happen (at least there is no sound, since I cannot see anything). I am left with a completely white screen. Things are fine with the failsafe mode.
View 9 Replies View RelatedSince 11.2 installed but shows blank screen at boot despite booting into runlevel 3 with acpi=off and noapic, I decided to try 11.3 M4 again.Media check is OK for 11.3 M4.Boot from MBR. GRUB menu shows Ubuntu and Windows 7 as well as openSUSE 11.3 desktop default and 11.3 failsafe. Both opensuse11.3 default and 11.3 failsafe return a blank screen despite the following boot options:
33 acpi=off noacpiI still cannot get to a terminal to run sax2. I read from a thread of opensuseforums (Opensuse 11.2 Blank Screen) where similar problem was solved using the correct driver which is actually "ati", NOT "radeon" for ATI Technologies Radeon Xpress 200M.Then because both Windows and Ubuntu boot fine from GRUB menu, it occurs to me I should boot up Ubuntu and try to locate openSUSE's /etc/X11/xorg.conf in order to edit the file and change the driver to "ati".In Ubuntu, xorg.conf of opensuse 11.3 M4 shows:
Section "Device"
Identifier "Configured Video Device"
EndSection
[code]...
I have tried two distros - Mandriva and OpenSuse. Both provide the same results, though Mandriva booted...but still the same problem, after installing blank screen comes up and nothing. Keyboard touch bad, mouse nothing happens. I would prefer openSuse but may have to switch.
Equipment:
Acer 7740 17" laptop
Intel i3-330M Chipset
4Gig DDR3 RAM 1066
Intel Integrated HD Video 128MB
Install Win7 64-Bit no issues, wiped and installed Linux and I cannot get past this blank screen. Installation works, no problem installed packages etc. When coming up on 1st boot, login - boom nothing? Searching the web and I suspect the Intel graphics are the problem but I'm not sure.
I bought this laptop to put Linux on it solely for a personal project of using Linux for a year. I'm an IT professional for 23 years and comfortable with CLI.
I installed 11.3 as a new install over 10.3, kept the $home and windows partitions, and let it reformat the other two partitions. NO disk partitioning structure was changed.
I did get a warning that GRUB over 128GB might not be able to boot.
I did enable the MBR.
GRUB menu does come up, but upon selection of SUSE 11.3 entry the computer screen blanks, and nothing happens. Selecting Windows does work upon power-up.
I did not have this 128GB issue with 10.3. What are my options? I am really afraid to install 11.3 on production machines now (running 11.2).
I have been trying to install openSUSE on a dell Latitude XT all day, and every time I tried to live boot, I got a blank screen. I finally decided to do a text install and I got it installed, but now I get the same result from booting off of the splash screen.
I can boot into text mode fine (still) but for whatever reason, it bombs as soon as I tell it to load the GUI. I have a 1.2 GHz Core 2 Duo, 3GB RAM, and an ATI mobility chip (2000 series, maybe?) I had the same problem with Ubuntu, and since I like openSUSE just as well, I figured I'd try it because I at least could do a text install from my liveCD.
For some reason, sometimes after I just turn the computer off by pressing the power button while hooked up to the video mount, I'll turn the computer on and (after it automatically logs into the standard user) come to a blank black screen. The only thing I can access is by pressing Alt+Tab to get a "no present windows" window, and thats it. Could it be that an activity or something has been deleted somehow?
View 1 Replies View RelatedI went to lock the screen when I got up from my computer. I came back and there was a black screen. I tried hitting different buttons nothing worked. I rebooted and still went right to black screen. I can get into recovery mode but I can't figure out what's wrong with the computer. Can someone give me a hint. My father is very good with ubuntu but he said that he would just reload the os on it. But I really don't want to go thru that process all over again.
View 2 Replies View RelatedI am running 9.10 on a HP Compaq. Every few days X will die. The screen goes blank and will not display anything. I have to SSH in, but even trying various commands like gdm restart does not help. I eventually have to reboot the box. Below is a snippet (hopefully not too large) of dmesg:
/dev/sr0 on /media/cdrom0 is a CDROM, but I dont think thats the issue.
[707515.629800] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[707515.629806] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[707515.629811] Info fld=0x45d18, ILI
[707515.629813] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
code....
Why is it on Ubuntu/Maverick that my display insists on going BLANK after a certain period of computer inactivity EVEN THOUGH I have NO screensaver functions set and the put screen to sleep function in power management is set to NEVER and ALL functions in BIOS are all set to not have display go into suspend mode ?
View 2 Replies View RelatedI have installed fedora 10 successfully but when reboot the system after installation not initrd or vmlinuz load and display first blue screen and some processing show after this blank screen display and held the system please tell me what should I do? I have reinstall many times but the problem is same.
View 3 Replies View RelatedI just installed Linux 5.5 on a Toshiba laptopn (i3, 64 bit). Centos runs until it reaches a very dark screen. On a few occasions, I am able to see something but the screen is very dark.
View 1 Replies View Relatedi am trying to install opensuse 11.2 to my vaio laptop i have win7 pro 64 bit already installed so i'm trying dual booting i have followed the below steps1- on windows, shrink the c partition and create a new unused volume for suse2- install the suse 11.2 on the new unused volume with hdd config like sda4 swap 4 gb sda5 20 gb / ext4 sda6 120 gb ext43- selected custom packages and started the installaton4- installation started smoothly and after installing packages it tried to reboot the machine at the end. But after this point the reboot operation has failed and gave a blank screen.
At the end the installation failed.I started the machine vaio boot logo comes and stops. i can't even enterbios setup or change boot options.I have unplaged the hd reset the partions, pluged it again and recovered win7So i think the installation damaged the file system.i have tried the above steps 2 times and came up with the same result.I have installed fedora 13 before with no problem.
Just finished wiping and re-installing F12 From a DVD on an Dell Inspiron 9300 with a NV 6800. The NVidia site driver refused to install, so I used the method documented here
[Code]...
as instructed to in the sticky. On rebooting, after the load animation, the screen goes blank/black. If I click around, I can hear some beeps from the OS so I assume that things are running but i just can't see anything.
I just upgraded to Ubuntu 10.04 LTS from 9.10. After the upgrade process, I restarted and chose "Ubuntu, with [the current kernel]" and now I am greeted with a white screen with no login or boot splash. My processor is pegged according to the processor case light. My computer's specs are as follows: AMD Athlon X2 5200+, ATI Radeon X1300 Pro, 2GB DDR2 ram, Dell Socket AM2 Motherboard, and 250 GB 7200 RPM hard drive. I really need to get this computer to work.
View 7 Replies View RelatedI fixed this issue on 10.04, but just recently (1 hour ago) upgraded to 10.10 and am having the same issue. Machine boots fine, but the screen is blank for most of the boot, and plymouth is up for about a half second before I get to the login screen.I've tried searching the threads, but for the life of me I can't find the solution and can't remember what I did to fix it on Lucid.
View 4 Replies View RelatedI tried in November last year to install 11.2 on a machine with NSRock K8NF6P motherboard which has an onboard GEForce class 6 graphics card. Installation went ok until the very end. Then driver problem surfaced, display went blank and was then damaged and required repair.
The NVIDEA driver install appears to require the system is up and running before it is installed. As I did not get a running system how do I install the drivers before any damage is caused?
I am having the same problem, as soon as X tries to load my screen just goes blank. I have an ATI Radeon 9550. At first I tried switching between VGA and DVI as well but upon ruling that out, I switch to my on-board video card and that is working thus far, but I'm trying very hard to figure out a way to be able to switch back. Anyways I'll check back in later on if I have any new information I will post.
View 3 Replies View RelatedJust upgraded from Karmic to Lucid.. Everything was running smoothly except compositing so I enabled the Open Source Edge repos and downloaded the latest driver my card (a ati radeon x1650). I rebooted to a bios splash and then nothing.. blank screen. After about 4 seconds of nothing the monitor flicks on showing the kubuntu bootsplash for a split second then blank again.ctrl + alt + f$ isn't displaying a tty for meI'm not getting the usual grub menu on startup (esc isnt bringing it up)(it's a usb keyboard enabled in the bios)
View 3 Replies View RelatedI have installed Ubuntu 11.04 along side windows 7 ultimate. But the problem is as soon as I switch on my computer. There is only a blank screen with my TFT screen displaying a msg "Out of Range"
Then suddenly Ubuntu loads without showing any option to load windows 7.
I have an system that d8.2 appears to install correctly. On first (or subsequent) boot, I get the DB8 load screen, then a quick fsck, then nothing. I appear to have some sort of environment running as I can move a mouse pointer, but nothing else.
CTRL-ALT-F2 results in the mouse pointer vanishing, but nothing else. I expected to end up at the CLI.
I have tried different installs and options, always the same result. This machine ran an earlier version with issues.
I have this machine (motherboard ITX Jetaway NF94-270-LF based on CPU Atom N270, full specs here) as a server for some time now (about 4 years). Debian 8.1 is installed on it.
Two days ago, after a power failure, the machine was not able to complete the boot process. I attached a keyboard and a monitor (on VGA port, the motherboard also as a DVI one, but I don't have a suitable monitor) to be able to see what's happening and interact with the machine. Unluckily, at a certain point during the booting sequence the screen goes blank and the monitor goes in standby mode; apart from that, the boot process continues in the background.
As far as I can recall, this behaviour existed for at least a couple of years (if not from the beginning) and the boot process was always completed successfully until two days ago.
The screen goes blank after the setup of the keyboard mapping. I tried everything to avoid the screen going blank: in the Grub menu I set the "vga" parameter, the "nomodeset" parameter, the grub_gfxmode parameter, I removed the "quiet" option, I removed the "load_video" line, I forced the BIOS to only use the VGA port for the video and so on, in order to disable or configure differently the video and the framebuffer. All these stuff had no effect at all: the screen keeps going blank at the same point during the boot process.
The only way I was able to use a fully booted system through keyboard and monitor was via the rescue mode of the Debian 8.1 netinst image. But that way, of course, I wasn't able to observe the normal boot process. So, I checked the boot parameters of the rescue mode and I found that the only usefull parameter was "vga", which I already used and was ineffective.
I have some problem with Debian 7. Just installed Debian 7 wheezy.
Motherboard Intel D2500CC, graphics - Intel GMA 3600. Monitor (BenQ V2200 Eco) connected via VGA cable. No X server installed.
After GRUB boot as soon as modesetting kicks in, the monitor loses the signal and goes black. Keyboard does appear to be active, as Ctl-Alt-Del will cause a reboot.
I tried nomodeset, vga=791, 771 etc kernel parameters, but this won't work.
Last night I upgraded from 9.04 to 9.10 in search of faster internet (which I got by the way), but now whenever I try to boot it goes to a blank screen for about 10 minutes befor going to the desktop. Its completely blank and has no cursor or anything. It's a huge problem and I could really use some help. 9.04 never did this.
View 9 Replies View RelatedI have a blank screen on boot up. Has happened since 10.04.It's this problem[URL]I tired their three solutions did not work however clicking F6 and slecting nomodeset before booting got farther then ever and then saidI have tried different images, betas RCS full versions, netbook, derivatives and its all the same.hats going on? Can it be fixed and is this always going to happen now or is it just a two cycle bug?
View 3 Replies View RelatedI have a HP EliteBook 2730p. lspci reports this for my graphic card:
Code:
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device 30eb
Flags: bus master, fast devsel, latency 0, IRQ 30
[Code]....
I updated from Lucid to Maverick. When I boot with the new 2.6.35-22 kernel the screen stays blank after grub. When I boot the old 2.6.32-25 Kernel everything works fine. I tried to boot 2.6.35-22 in Recovery Mode. When I do this I see some kernel messages in text mode and then the screen goes blank again.
I upgraded 10.10 from 10.04 from the update button from within the update manager. It seemed to upgrade ok but after I shut down and turned it back on it goes to a blank screen. If I then hold the power button to turn it off and back on it then loads to a boot screen where about 6 options with recovery option are listed. The top 2 options do not work as they just go to a blank screen but the bottom 2 give me some other choice including seeming to boot up to a normal Ubuntu environment. How can I fix it so that it boots to a normal Ubuntu 10.10.
View 8 Replies View RelatedI have always had Ubuntu installed along with Win 7 but rarely use it, i only use it if i am flashing firmware to my phone or something similar.
I uninstalled my older version of Ubuntu because it was becoming sluggish and have tried to install the 10.10 version a few times today, but every time i boot into Ubuntu, i get a blank purple screen and nothing else.
My mouse curser is the only thing that is working but there is nothing to click on and nothing shows if i right click.