OpenSUSE Hardware :: Soundcard Not Detected?
Mar 1, 2010
My sound stopped working! (after a fresh install, explained below)I just installed the latest release of openSuse. Right after installing, I ran the updates tool and got all recommended updates. All fine.I then installed my ATI catalyst drivers. Rebooted a couple of times. All fine.Everything was working 100% (including sound), I then rebooted, now something is wrong.Now my sound is not working, I right-click the speaker icon in the taskbar, and to my surprise my soundcard is not listed like it was just before. It used to show up as an X-fi card, which was correct.
In Yast, I go to sound, and in the hardware section, there is nothing there, my soundcard is not listed. I tried to add a soundcard in Yast, (creative xfi) but it wont install, I get some IRQ error.I'm all out of ideas. I'm a new to using linux, but I know my way around the console.I have trolled through the internet for hours to no avail
View 7 Replies
ADVERTISEMENT
Jul 24, 2011
Motherboard: Intel DP35DPlspci:
00:03.0 Communication controller: Intel Corporation 82G33/G31/P35/P31 Express MEI Controller (rev 02)
Subsystem: Intel Corporation Device 5044
[code]....
View 1 Replies
View Related
Dec 30, 2009
I'm using an external Cambridge Audio Dacmagic with F12 and Amarok. This worked great, until I upgraded Fedora this morning. The Dacmagic does not appear anymore in the Multimedia Audio Systems settings, only Pulseaudio is shown. However, in my hardware info widget, the Dacmagic does appear? This is shown as "C-media USB Headphone set". Now I'm totally lost. I did restart Fedora with the Dacmagic on, I did restart the Dacmagic with Fedora running, but nothing changed.Any good suggestions on what I can try next--- Post added at 04:47 PM CST ---------- Previous post was at 03:05 PM CST ----------Isn't the net fun? Poking around, I found I could try "lsusb". The output gives:
[root@Mediacenter ~]# lsusb
Bus 004 Device 002: ID 0d8c:000c C-Media Electronics, Inc. Audio Adapter
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[code]....
View 5 Replies
View Related
Dec 27, 2010
I was using alsa, but then reverted temporarily to pulseAudio due to a minor issue. Later on, I did remove pulseaudio through yum. And that was the end. No matter what alsa/pulseaudio version I install or reinstall...
[NetGh0st@localhost ~]$ aplay -l
aplay: device_list:235: no soundcards found...
[NetGh0st@localhost ~]$ cat /proc/asound/cards
[code]....
It does not find my soundcard, and I have a nasty feeling that the whole sound module was removed ... i don't know, may be from the kernel...
View 5 Replies
View Related
Dec 15, 2010
My sound was working quite fine with Fedora 13 (Internal Audio) until I decided that I want to install the appropriate driver from the vendor's website.
[Code]...
View 2 Replies
View Related
Sep 1, 2010
I was listening to music and decided to check update manager, and after the install I reboot and then POOF, sound is gone, I checked Alsamixer and got "no such file" did aplay -l and got that there was no soundcard found, which I officially can say is bull, since, I DO have a card, hahaha. I am running a HP G72 and already went through the comprehensive check and kinda got with seeing which driver matched my card*EDIT*
heres some info I forgot to post
Code:
00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03)
Subsystem: Hewlett-Packard Company Device 1484
[code]....
View 9 Replies
View Related
Dec 20, 2010
New install of 11.2 with KDE 4.I have two soundcards in my system, one on the motherboard and a soundblaster. I multiboot and all FIVE other images, including SUSE 10.1 with KDE 3, use the soundblaster so that is where the speakers are plugged in. 11.2 insists on configuring the motherboard sound card for KDE, even when I do a fresh install setting the soundblaster as the primary sound card at installation time or when I remove the motherboard sound card from the configuration after installation. KDE 4 never even lists the soundblaster as a known card. Any way to fix or work around this restriction?
View 9 Replies
View Related
Jan 24, 2010
I have 2 soundcard - a M/B built in Intel AC97 and an old Aureal (later SoundBlaster). This is because there's a problem with Intel's microphone in XP. So I use Intel for playback and Aureal for recording.
Now, how do I duplicate same setup in Suse (to avoid switching plugs) ? I am a bit lost in where to specify hardware to be used for recording and playback.
View 5 Replies
View Related
Mar 25, 2010
Recently I installed a new soundcard to my computer, and I don't have any sound anymore in Linux. Now I have in YaST two sound chips, one AC97 and my soundcard Asus Xonar Essence STX. Obviously Linux detected my soundcard since the custom driver called "Virtuoso" is there. However, my soundchip has still the slot 0, and my soundcard is not configured yet. And here I'm stuck, because:
1. when I tried to delete the AC97 entry, YaST hangs (actually y2base or something like that, the sound subprogram). Alternatively, I tried to just disable the driver, but this wasn't possible (unlike with Windows, where you just click a checkbox).
2. when I tried to configure my new soundcard, the configuration program got stuck again - with every of the three alternatives (fast setup, normal setup and custom setup or so).
I also tried whether the old soundchip is still working, plugging in my headphone into the output of the AC97 soundchip, but I didn't hear anything, so system sound really seems to be broken.
View 9 Replies
View Related
Jan 2, 2011
I have the problem that for working properly my soundcard needs sort of re-initialisation after every reboot (11.3, 64 bit). I have to change a setting in the sound module of yast that causes the yast to rerun its final steps. What is not working otherwise is audio playback from a usb TV-stick (recording is no problem, same as playing an audio/video file). any idea what might be the problem? how to call the final steps of the sound module of yast from the command line, I could at least put that call into boot.local to avoid having to call yast.
View 9 Replies
View Related
Apr 14, 2010
Trying to get external microphone to work via CMI 8738 soundcard. Using SuSE 11.1, KDE 3.5, (No pulse). Mic works on other computer. rpm -qa '*alsa*'
alsa-oss-1.0.17-1.37
alsa-1.0.18-8.12.1
alsa-utils-1.0.18-6.4
alsa-plugins-1.0.18-6.12
[Code]...
View 3 Replies
View Related
Jan 22, 2011
I got some troubles with my external VGA output of a Notebook. I tried various things (see below) but now I ran out of ideas. I studied the sticky post in this forum about configuring graphics cards but unfortunately this gave me no new hints. My System:
Fujitsu Siemens Lifebook E Series
OpenSuse 11.3 (i586, 32Bit)
Graphics: Intel 965GM
I found lots of questions and solutions concerning the 965GM but they all are just about configuring the VGA monitor/screen in Xorg.conf.d / xrandr. I'd LOVE to do so but in my case the VGA outout isn't even detected for some reason (please see details below) Summary of my findings up to now:
[code]......
View 8 Replies
View Related
Mar 16, 2011
I have been using Fedora for a while. I decided to upgrade, and that I wanted to do a network install, but I didn't want to go for Fedora 14 when 15 comes out in a couple of months, so when I found openSUSE 11.4 was released this month, and also supported a net install, I decided to go for that. Yesterday I downloaded the net install CD. I burnt it from Windows. It burnt and installed successfully. When I got into the system this morning, it doesn't detect my DVD drive at all. There is no device for it in /dev, nor is anything shown by /usr/sbin/hwinfo --cdrom. When I insert a CD/DVD, it (the drive) detects it, but does nothing more. If I boot to Windows, it works fine. It is connected properly (I built it myself, and upgraded the drive about six weeks ago).The DVD drive is a LG GH22LS50 SATA one, connected to the SATA3 port on a Gigabyte GA-P67A-UD3 motherboard.I found this in dmesg:
Code:
[ 1.528777] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.528789] ata2.01: SATA link down (SStatus 0 SControl 300)
[code]...
View 6 Replies
View Related
Apr 20, 2011
with opensuse 11.4, my gps qstartz 1000z seem detected like a storage mass
[Code]....
View 4 Replies
View Related
Jun 5, 2011
It seems my Xonar soundcard is not detected by Suse, is there anything I can do about this?
View 9 Replies
View Related
Feb 9, 2011
a few day ago i have checked my application and make rs232 cable converter to communicated it. And not detected, why? FYI, this is my lsusb command, but in my dmesg, was not found. check this out, (usualy there is another rows, just like ".....converted to ttyUSB0....")
View 1 Replies
View Related
Apr 15, 2011
I have been using dropbox for quite some time but in the last few days I have been bumping into a problem.Recently I had a fresh install (GNOME3 and afterwards added KDE 4.6) and after installing dropbox I get the following error:
Code:
*** glibc detected *** /home/filipe/.dropbox-dist/dropbox: double free or corruption (!prev): 0xb3d44d08 ***
and dropbox terminates...
[code]....
View 8 Replies
View Related
Jan 30, 2010
REcently i hav installed opensuse 11.2. now it does nt detect the laptop keyboard and touchpad...but it detects a usb keyboard and mouse....
View 4 Replies
View Related
Jun 5, 2011
I have a 1TB USB 3.0 verbatim portable drive. When I connect it to my IBM Thinkpad R500 OpenSUSE 11.4 does not detect the drive as being plugged in. All my USB 2 devices work fine. Do I need to configure something to get this drive going?
View 1 Replies
View Related
Jan 26, 2010
1.Keyboard and touch pad not detected.
2.wifi not detected
View 9 Replies
View Related
Jan 26, 2010
i have installed opensuse 11.2. the keyboard and wifi are not detected...
View 3 Replies
View Related
Jul 4, 2010
I have 2 physical 500 GB Sata drives/stripes that appear as 1000 GB C: drive under WinXP. I have partitioned that drive into 750 GB Windows native C: and an empty 250 GB partition F:
When running the installer for OpenSuse 11.2 only the physical drives appear in the list of available hard drives 2x 500 GB (= sda and sdb), rather then the partitions of 750 and 250 GB (would expect sda1 and sda2). Is it possible to install Opensuse on the 250 GB partition (F: under windows) without destroying the WinXP installation and data on the C: partition?
View 9 Replies
View Related
Apr 2, 2011
I just installed 11.4 and I get an error when I try to boot, "fsck failed for at least one filesystem". It's referring to sdc2, which is my /. This drive is a 1.5gb SATA drive, and it may be that this drive is very slow to initialize. I used to have a problem in Windows where this same drive wouldn't be detected after waking from sleep, so I had to apply a hotfix patch.
I tried manually fsck-ing, but the drive isn't detected at all. Maybe some way I can make it wait longer for the drive?
View 3 Replies
View Related
Oct 28, 2009
Just discovering Linux. Couldn't expect everything to work right away, of course. I has some issues with the x11 (the GUI wouldn't show itself), but have gotten around that. Next is WLAN. I have a Motorola USB stick whose chipset i've identified as the Ralink T2501.
It won't show up in YAST as a WLAN adapter, but does in the USB devices attached. I've procured what the sticky advised, and this is it:
HTML Code:
40: USB 00.0: 0000 Unclassified device [Created at usb.122]
UDI: /org/freedesktop/Hal/devices/usb_device_148f_9021_noserial_if0
Unique ID: CiZ2.Q1gxt8A0_KF
Parent ID: uIhY.3f5c44ENLJ9
[Code]....
Anyway, i've downloaded the necessary driver (rt73), but don't want to leap into installing it before i consult you guys. Where do i go from here?
View 9 Replies
View Related
Feb 16, 2010
I have a D-link dir-635 firmware v. 2.30eu (latest) and a USB WLAN adapter D-link DWA-140 802.11n. The driver seems to be installed correctly since lsusb lists it correctly and all the wireless networks in the vicinity are detected including mine. When I try to connect however NetworkManager says it is activating but after awhile the windows with the newtork password appers. dmesg output:
[ 5509.487262] wlan0: direct probe to AP 00:1c:f0:71:03:88 try 1
[ 5509.684014] wlan0: direct probe to AP 00:1c:f0:71:03:88 try 2
[ 5509.884020] wlan0: direct probe to AP 00:1c:f0:71:03:88 try 3
[ 5510.084014] wlan0: direct probe to AP 00:1c:f0:71:03:88 timed out
So it is able to determine the AP:s mac address but each time it times out.
I have tried disabling the security on the router but no luck.
Not sure what to try next. I have checked some of the tips supplied in these forums but none seem to handle the issue I am having.
View 7 Replies
View Related
Jul 17, 2010
an issue with my broadcom wireless that is using the bcm4312 driver. I installed the b43(?) cutter firmware from the command line and now my network is detected but it just won't actually connect to it. My router has wpa security enabled but i think it worked with it before.
View 9 Replies
View Related
May 4, 2010
I use OpenSuse 11.1. My graphic card is an intel Q43/Q45 chip. I was instructed to update my xorg and mesa packages in order to make on application work (it was crashing my x server). After I did so, x wouldn't start:
intel(0): No kernel modesetting driver detected
Screen(s) found, but none having a usable configuration
Now I am stuck with vesa if I want to have x running at all. I tried reverting to the versions of mesa and xorg I had before, when everything worked, but to no avail.
What can I do? (I am by no means an expert and that I don't know linux very well, and even less openSuse... just has to use it at work....)
View 9 Replies
View Related
May 23, 2010
I have Onboard Realtek ethernet card (eth0) it worked fine but suddenly it stopped working when i see in yast it shows hwinfo not found. when i use hwinfo --netcard it gives realtek card name thats all. I went to yast >lan> edit> hardware and tried to add r8169 module but it was not accepting. previously created ifcfg-eth0 file is available but its not getting up.when i say ifup eth0 it say interface not found. the same messg is also available in /var/log/boot.msg.
View 4 Replies
View Related
Aug 3, 2010
I have installed opensuse11.3 on my dell desktop. I get the gui with only 4 or 8 bit colors. I have resolution 0f 1024x768, which I have given at installation time. I cannot change it any more. I have followed your SDB:Configuring graphics cards - openSUSE guide. here is my lspci output
[code]....
I have tried to configure the xorg with command Xorg -configure. I surprised that it cause Segmentation fault. I have captured the Xorg -configure command in strace. I am pasting here certain last lines, I cannot paste the whole output because it is too large.
[code]...
View 3 Replies
View Related
Mar 23, 2011
I have a Sony MP3 player which is a SOK-NWZ-B512F(B) model that couldn't detected by OpenSUSE. I did try on other pen drive which is a Kingston brand, it is detected and a pop-up message mention that I have an USB drive connected.
View 7 Replies
View Related
