OpenSUSE Hardware :: External USB HDD Not Recognized At Boot Time
Mar 20, 2011
I am actually working again on a problem i had already on opensus 11.3 (never resolved), and now also after the upgrade to 11.4 .
I do have an external HDD (Samsung STORY Station) usually connected to the linux server. I also have udev rules setup to automount the device on /media/xxx by label.
I used to have my own rules, now have some more coplete from the internet.
When I now reboot the server, the "sd*" device for story station is not created, and obviously not mounted.
If however I do switch of th estory station after reboot, and turn power on again, the device is configured and properly automounted as by udev rules.
Also during the boot the device is seen as from boot.msg:
Code:
<6>[ 1.444939] usb 2-2: New USB device found, idVendor=04e8, idProduct=5f06
<6>[ 1.448686] usb 2-2: New USB device strings: Mfr=1, Product=11, SerialNum
ber=3
<6>[ 1.452462] usb 2-2: Product: Samsung STORY Station
<6>[ 1.456217] usb 2-2: Manufacturer: JMicron
P.S.: I used th esearch function and google, but did find many similar articles but nothing matching my scenario. So I hope I did not miss something obvious.
View 9 Replies
ADVERTISEMENT
Jul 18, 2011
I have installed "open-SUSE 11.4" on a "500GB Free Agent External Hard Drive". I didn't have any problem in booting since last week that I booted it from my laptop. Also I did it before several times from then when I try to boot it e.g. from an "Intel(R) Core(TM)2 Quad CPU Q9400 @ 2.66GHz" PC the time between loading INITRD and starting boot sequence messages lasts nearly 30 minutes!(i didn't actually measure it but it take a long time in the same order). after starting boot sequence which is showed on monitor everything looks normal. e.g copy of files would be done by speeds between 2MB/s to 30 MB/s depending on the targets.I used to use the external hard derive to boot from different laptops and PC's from start but I didn't have such a problem anytime.
View 1 Replies
View Related
Jan 16, 2011
I have gone through Mint, Ubuntu, Fedora, and continue using them on different PCs but I recently had a problem with my graphics card on new releases.. another story all together.So I am using OpenSUSE 11.3 on my Dell inspiron 1526 AMD 64 bit. I have always been able to plug in my external HD and have it show on my desktop. Now with OpenSUSE something is different. I tried other flash drives, all show up and open to view on their own, but my 1GB ext HD doesn't. I am not a pro with the Terminal yet but I prefer to use it and am good at reading and copying commands from online.
jason@linux-z81g:~> lshal -m
Start monitoring devicelist:
04:35:12.017: computer_power_supply_battery_BAT0 property battery.voltage.current = 12479 (0x30bf)
04:35:17.813: usb_device_1058_1102_57442D574341553432313937303738 added
04:35:17.833: usb_device_1058_1102_57442D574341553432313937303738_if1 added
04:35:17.839: usb_device_1058_1102_57442D574341553432313937303738_if0 added
code....
as you can see it says "My Book" which is the name of my ext TB but where is it and how do I mount it?
View 14 Replies
View Related
May 2, 2010
OpenSUSE 11.2 server, Gigabyte GA-MA790X-UD4P sda for system, 3 ext4 partitions, working fine.sdb promise RAID1 for data, 1 ext4 partition, working fine.sdc is an eSATA docking station for data backup, 1 encrypted ext4 partition -- here lies the problem.
This configuration has been functional for months until I decided to add two more external drives (sdc) to rotate through backups. I had difficulty with encyption on the first new drive and eventually decided to start over. Using the gui Yast Expert Partitioner, I deleted the single partition. That began a real nightmare...
Since deleting the partition, the system detects drives inserted in the docking station, but does not report them (including a different fully functional drive and a brand new unused drive). I have tested all drives on other computers and they function perfectly. I have rebooted the system several times while troubleshooting this issue.
Could not recreate the partition on server (since it does not recognize the drive), so I used Gparted on another computer - it all went without a hitch, formatted ext4. But when I placed the drive in the dock, the drive still was detected but not recognized.
Details:
BIOS lists the eSATA drive
Entering Yast Expert Partitioner, error message follows:
The partitioning on disk /dev/sdc is not readable by the partitioning tool parted, which is used to change the partition table.
You can use the partitions on disk /dev/sdc as they are. You can format them and assign mount points to them, but you cannot add, edit, resize, or remove partitions from that disk with this tool.
Yast partitioner shows drives: sda, sda1, sda2, sda3, sdb, sdb1 sbc is not listed.
# fdisk sdc results in: Unable to open sdc
# dmesg | grep tail reports:
[48442.370779] sd 0:0:0:0: [sdc] Unhandled error code
[48442.370793] sd 0:0:0:0: [sdc] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
code....
So how did partition deletion cause this issue, and how do I correct the problem? It is possible that my difficulties encrypting the first new drive are related (it's not my first time doing it successfully). It seems the problem is in the Kernel or configuration. I have invested many hours in forums and on google - tried dozens of possible fixes. I'm beginning to suspect system corruption or a bug, however all other system functions are working perfectly.
View 5 Replies
View Related
Sep 18, 2014
I have a backup HDD with a different distro for my laptop and i can boot into it via external usb or if swapped into the laptop. This HDD/install in question is debian testing and was working fine, the issue arose suddenly. I was first suspecting a failure of hardware somewhere on the motherboard, but the hdd i was using with an external usb adapter also works when installed into the machine. also, the HDD is recognized once i have booted using the external HDD and distro, but it is not recognized by the bios. so i dunno, my first guess is something became corrupt within the testing install, but i guess its also possible that there is some wrong with the HDD but thats not immediately apparent as all the data is still accessible.
Should also note that the HDD with testing on it is also recognized when connected via the external usb adapter, while booted from alternative distro/HDD.
Also. just tried this, but i can get the testing HDD/disto to boot if connected externally. it was going pretty quick, but there i did catch a line about a corrupt filesystem. any commands to run to see what might be going on?? log files to look at?
View 0 Replies
View Related
Jun 19, 2011
Increasingly over time, i.e., days I experience that the keyboard (and mouse) is not recognized when booting.Now it's every time I boot. However, there is a fix. If I plug out, and immedeatly plug in again the keyboard connector everything is fine, except that keyboard short cuts not always work depending on application. In the mouse case the right mouse button doesn't respond either. Besides these effects the system, openSuSE 11.3, boots fine. It's a hazzle everytime to plug in and out again. I'm opting for another fix. Nothing suspicious in /var/log/messages. I've tried to see if there is a particular led light sequence on "num lock", "Caps lock", "Scroll lock" that I can get som info from, but I haven't been successful.Anyone got a suggestion to what might be the cause of this behavior?
Keyboard is kwd-205
Mouse is Microsoft wheel optical mouse
Base Board Information
[code]....
View 5 Replies
View Related
Mar 1, 2010
I have a Microsoft Wireless keyboard / mouse which I use for my Windows world. I have tried booting the OpenSuSE 10.2, 11 DVDs, but none of them recognize the wireless keyboard that I have connected and I am unable to proceed with the installation because, the default selection in OpenSuSE's first installation screen is *Boot from HardDisk* I also tried using the Ubuntu Live CD that I had, the same problem of keyboard not recognized, but the lucky part was, the first screen in the live CD was a language selection and the default language was English and timed out and moved onto booting the Live CD. Once the booting was over, the wireless keyboard and mouse worked like a charm!
View 7 Replies
View Related
Jan 4, 2010
does anyone know that if i can boot from an external hard drive with "openSUSE" installed on it?
how about FireWire, will it work?
i'm trying to set up a triple boot for me newly bought iMac.
View 4 Replies
View Related
Mar 12, 2010
I bough a 640 GB external USB disk.I found something wasn't working well when I couldn't restore a backup from the disk (with sbackup).So I tried to convert the filesystem from fat32 to something newer.I installed gparted, and it shows no partitions on the 640 drive (however, I can access the filesystem!!!). Also, for some reason it shows as a 298.08 GiB drive.So I thought I should format it to solve this. When I tried to do this, gparted simply closed, with no error messages.
View 9 Replies
View Related
Apr 5, 2010
Jaunty is fully updated but SUDDENLY is not recognizing external devices (card reader, camera, DVD inserted in drawer, etc.) In other words, I cannot see my media and, therefore, cannot open it.
Anybody else having problems here? What's up? Did something go wrong in the updates?
(AMD64 running stable Jaunty 9.10 fully updated)
View 3 Replies
View Related
Jun 18, 2010
I'm trying to install Lunar Linux OS on my external HD alongside other OS's but only my fixed HD appears during the install process. I already have two Linux installations on the EHD. Is there a way around this problem or will Lunar only install to an IHD???
View 3 Replies
View Related
Jan 9, 2016
Recently (in 2015) our Debian systems started not to recognize HDDs connected via an external docking station.
On my computer I run: (uname -a)
* Linux violin 3.16.0-4-amd64 #1 SMP Debian 3.16.7-ckt9-3~deb8u1 (2015-04-24) x86_64 GNU/Linux
* If I connect to a flashdrive to the USB2 port, it is recognized as sd* (messages are also written to dmesg/syslog)
* If I connect the USB3 connector of the external docking station with an 1TB WD SATA docked, to this USB2 port (the external docking station has its own power supply, so I do not expect to have a problem with the current, the drive spins up and is spinning), there is nothing in the dmesg/syslog, and no new items under /dev/sd* or lsusb or similar tools.
* If I connect the same external docking station with the same disk via eSATA on a different computer it is recognized. That computer runs the same debian. If I connect through its USB2 port it does not work either.
* I also tried another docking station and USB cable.
View 7 Replies
View Related
Jun 16, 2010
I have an external hard drive that connects through an expansion card with eSATA on it. It was partitioned and formatted as NTFS in Windows but isn't recognized in Ubuntu 10.04.
View 1 Replies
View Related
May 25, 2010
I have a Maxtor external storage HDD with firewire (1394) interface.
When I connected it with my computer, which is running an up-to-date Debian squeeze, it was recognized as "/dev/sda1" and replaced the existing partition on the computer.
View 2 Replies
View Related
Jul 31, 2010
I have a laptop that came with no OS. It has no internal HDD, so I formatted a 320gb external HDD and installed openSUSE 11.3 from another computer onto the external hdd. I can't seem to boot from the external hdd on the laptop though. I have it set as the primary boot source in BIOS. Is it possible to boot from external hdd or am I missing a step?
View 7 Replies
View Related
Nov 20, 2009
This sounds strange, but my laptop (running 11.2) won't boot correctly unless my external HDD (ext3) is on and plugged in. If I don't turn it on, it hangs at the start of udev. If I press ctrl+c, the system continues to boot, but the keyboard and mouse don't activate... don't function, etc. But I can press my power button and it does shut down. Going through dmesg (during a successful boot with the external HDD on), I saw this (not sure if it is relevant):
Code:
[2.201029] scsi 2:0:0:0: Direct-Access Ext Hard Disk PQ: 0 ANSI: 4
[2.201450] usb-storage: device scan complete
[2.206637] sd 2:0:0:0: [sdb] Spinning up disk......
[6.062434] udev: starting version 146
[6.225262] .
The device sdb1 is the HDD.
Now, I don't know much about udev. I can tell you that I have no sdb1 lines in /etc/fstab, and I have no autofs references to it.
View 8 Replies
View Related
Dec 3, 2009
A while back when 11.0 was recent i upgraded my computer to an hp pavilion desktop which only had SATA which wasn't compatible with my 500gb IDE hard disk. I then decided to buy a compatible hd (500 gb as well) and use an external hard drive case to put my old one into(which plugs into the USB ports) i currently have the external 500 gb partitioned with a linux native mounted at /home, and my other with NTFS and linux native mounted at /
Prior to updating to 11.2:I could power on my external hd(Thermaltake A2396) after grub and it would boot up no problem. if i turned it on too late or before grub was done it wouldn't load and i would have to log in as root in repair mode, turn the hd off then back on, wait for a couple of lines to pass(I assume the drive being detected) then mount /home, and init 5This didnt really bother me for the previous versions of suse much because i just had to remember to turn on the drive After updating to 11.2:the only way to boot is to wait, do the power on/off, mount /home, and init 5this gets to be quite annoying after a while and i was wondering if anyone knew a way to get it to mount itself while its booting. let me know if you'd like me to post any more info
View 8 Replies
View Related
May 18, 2011
I'm very new to Ubuntu. Now that I have it installed, my computer doesn't recognize my external hard drive or flash drive. How do I access my external hard drive and flash drive? I'm also trying to get Rosetta Stone to work using Wine, but having a heck of a time. I've searched the forums and have found some similar topics, but nothing that really helped me.
View 6 Replies
View Related
Oct 8, 2010
I am trying to get my computer to mount an external folder on a different machine with :
Code:
//192.168.1.200/share1/mnt/Documents cifsauto,users,username=user,password=useruser,uid=Alastairo,gid=users0 0
[code]....
View 5 Replies
View Related
Jul 2, 2010
I do this every time.
Code:
ifup dsl0
How can i set this to start at boot time?
View 9 Replies
View Related
Mar 30, 2011
i have compiled/installed Apache from source code ...however i don�t now how to start it at system start up as a daemon to run at level 3the server is usually started by the apachectl scriptwhich understand start stop restarti don't want to use suse distribution of Apachecan i just copy apachectl to /etc/init.d and make a link to it at /etc/init.d/rc3.d
View 4 Replies
View Related
Jun 4, 2011
I've just replaced my SATA boot drive /dev/sda1 with a 65Gb SSD (Kingston SSDnow V-100, latest version) but I find the much-hyped speed advantage almost negligible. I used to have boot times in openSUSE (fresh install of 11.4, measuring from GRUB menu to startup guitar chord) of around 50 seconds, and the SSD drive is only a little faster at about 40 seconds. I was expecting something more like half the previous boot speed.Haven't done any tinkering yet except for the noatime setting in /etc/fstab.
View 9 Replies
View Related
Oct 9, 2010
I'm planning to migrate from ubuntu server to open suse serverI'm testing the migration in a virtual machine and I'm having problems with mdadmEvery time Open suse boots I need to run mdadm --assemble /dev/md0 and activate the volume group vgchange -ay VGNAMEDuring the boot time boot.md and mdadmd are running but (startup scripts only scan) I believe mdmad is not running because needs to be assemble every time.
View 9 Replies
View Related
Dec 26, 2010
Are there any easy special tricks to speed up the boot time?Coming from Linux Mint (GNOME), I could get to the Desktop from cold in less than 25 secs.Now in openSuse 11.3 (KDE4.5) it takes more than twice that.Is this a function of KDE or have Ubuntu done something that openSuse hasn't to speed up the boot?
View 9 Replies
View Related
Jul 4, 2010
i have 2 partitions on dmraid. I am not able to configure them to mount with yast; yast partitioner gives an error stating that it can't mount a file system of unknown type. I am able to start the dmraid devices manually and mount them manually.
See bug:
https://bugzilla.novell.com/show_bug.cgi?id=619796 for more detailed info.
View 2 Replies
View Related
Aug 15, 2010
For some reason, every time I shut down and reboot my machine, the system time advances four hours. The local time here is EDT (-4hrs UTC). I have it set correctly in Yast and have the 'hardware clock is set to UTC' checked. However, for some reason, the next time I boot, the system time will be ahead four hours.
View 7 Replies
View Related
Oct 27, 2010
i have just installed opensuse 11.3 on a pc which was once a Windows XP,the configuration for opensuse installation well everything is good.The problem is when i switch off or reboot the pc,.at the 1er black screen where u see the 'boot' its says
Verifying DMI Pool Data........Update Success
(take 2mins almost then)
GRUB Loading stage 2......
(takes up to 10mins or more)
then i got this:
root (hd0,1)
Filesystem type is ext2fs,partition type 0x85
kernel /boot/vmlinuz -2.6.34.7-0.4-desktop root=/dev/disk/by-id/ata-HDS728080PL
[code]....
View 2 Replies
View Related
Dec 14, 2010
I use opensuse 11.3 and would like to see daemon status at boot time, instead of the chameleon with a progress bar
View 8 Replies
View Related
Mar 26, 2011
Though my upgrade from 11.3 to 11.4 went pretty well (X and apparmor/samba config to renew), I have a bunch of warnings at boot time. Sample: "* wil be removed in a future UDEV version..." On another box, I get some "/etc/*/ipv6" should have a .conf file. Should I worry / fix up something before next upgrade?
View 2 Replies
View Related
Apr 13, 2011
pm-hibernate and pm-suspend only work the first time after booting into runlevel 5. This behavior is reproducable. pm-hibernate starts out correctly but then hangs the system bevore it gets to save the image from memory to disk. The computer locks up and does not power down.
pm-suspend: on wake up there is no signal on the screen (pm-suspend called from X environment or text terminal shows same result). I spent some time reading information on s2ram s2disk and added the follwing options:
S2RAM_OPTS="-f" in
/etc/pm/config.d/00meine.config
(display adapter is GForce4 nvidia with the closed source nvidia driver for accel)
splash = n in
/etc/suspend.conf - to get some more information during the suspend / hibernate.
Any ideas to get pm-hibernate / pm-suspend to work more than one time after boot??? Hibernate would be a great start for daily work and for energy saving.
horstausdemwald PS: In runlevel 3 pm-hibernate works various times from a text terminal. Under the same condition pm-suspend leads to a scrambled text terminal after resuming (some help on this: using vga=normal in Grub). The computer continues to work - though without visual aid - when the text terminal is scarambled. For example Runlevel 5 can be called blindly from the text terminal.
View 8 Replies
View Related
