I'm trying to decrease the tcp TIME_WAIT state which, from what I understand, occurs on the host that initiates the closing of a socket by sending a packet with the FIN bit set. Most people say to change /proc/sys/net/ipv4/tcp_fin_timeout to a lesser value. I have tried this many times and it makes no difference. The TIME_WAIT's still linger for ~ 60 seconds. This link says that it actually adjusts the FIN-WAIT-2 state and I think they're right.[URL]
Quote:
/proc/sys/net/ipv4/tcp_fin_timeout
Time to hold socket in state FIN-WAIT-2, if it was closed by our side. Peer can be broken and never close its side, or even died unexpectedly. Default value is 60sec. Usual value used in 2.2 was 180 seconds, you may restore it, but remember that if your machine is even underloaded WEB server, you risk to overflow memory with kilotons of dead sockets, FIN-WAIT-2 sockets are less dangerous than FIN-WAIT-1, because they eat maximum 1.5K of memory, but they tend to live longer. Cf. tcp_max_orphans.
Here's what the netstat man page says about these two different states:
Quote:
TIME_WAIT
The socket is waiting after close to handle packets still in the network.
FIN_WAIT2
Connection is closed, and the socket is waiting for a shutdown from the remote end.
I am new to Fedora, and I noticed when I opened my home folder that I only had 54GB. My HD is 120, and when I used the disk utility, I noticed that 64GB are in ext4! What?! This was not a problem in Ubuntu, so why has it happened now? Is there anyway I can decrease the size of ext4 and give some of it to Fedora?
Initially i was on kubuntu 10.10 with kde 4.5.x and i realized that animations throughout kde stunk. For example, the kickoff menu would raise and lower very jerky. So thinking this was a kubuntu or even a kde 4.5.x problem, I made a switch to opensuse 11.3 and kde 4.4.x. After install i noticed that all animations, including the menu raising and lowering, where very smooth and crisp (like they should be). I later realized I wasn't even using all my hardware's power so I put my two gtx 460s in SLI=auto. After a reboot I realized that once again all animations got jerky again . This leads me to believe,and for good reason, that kde's visual performance is degraded with SLI enabled.
There seems to be quite a craze about reducing the Ubuntu boot times to 10 seconds. I never really reached the 10 second mark.. for me it was more like 30 seconds from when I selected Ubuntu in GRUB to when I was prompted to type in the password in GDM. First of all, is this what is meant by boot time? Secondly, I know this already is quite a good 'boot' time, but just for the sake of tinkering around, is it possible to reduce the time that elapses between the GRUB menu and GDM?
The track pad on a Macbook Pro 8.3 is hypersensitive and interprets the lightest touch as a click. Even brushing the track pad with the sleeve of my shirt counts as a click. How do I decrease the sensitivity of the track pad?
I am running Arch on a Sony Vaio 64-bit computer with an ATI Mobility Radeon HD 4650 graphics card (xf86-video-ati installed).
I am attempting to decrease screen brightness; I have tried editing /proc/acpi/video/VGA/LCD/brightness (gives me: "write error: Invalid argument") and xbacklight -set <value> (gives me: "No outputs have backlight property").
I have an issue with few servers. All have OEL 5.5 and various versions of oracle (mainly 10g something).
I've noticed on one machine that amount of free memory is slowly decreasing. When it comes to less then 30M, application has problems. Ive tried adding mem on this machine (virtual), and it behaves the same.
The same is on physical machines I have simmilar, if not the same config. Variations are with physical memory installed, and it does not matter if servers have 2G, or 8G, free -m gives around 30 free
It does not swap, and does not make some big issues on other machines, but on this one, application that uses this DB timeouts the user. Is there some chance to check what is creating this issue?
P.S. I've tried with DB admin to check something related to oracle itself, bit when we shutdown instance, Oracle frees 1.5G allocated to him, but nothing else. Will try testimg a bit more, but any thought on this is usefull. This is production server, so no big issues can be done. Will try to copy it to other hardware and do some testing, but then no App server available to attack it.
On F12 and sure need to upgrade. Way back when I first had a bad disk on the "system" disk that was 80G, I only had a 200G lying around. Next time that happened my other 200G wasn't "big" enough it said, so I put a 500G in there. Now it seems I got more bad blocks etc but I need to lower the size 'cos I don't want to put a 1Tb HDD in there. My question from all of this is, how do I decrease the image so I can put it all on a smaller HDD?
Used space on the system disk's partitions is about 30G, so an 80G disk should be sufficient. What I can think of is that I need to "move" all data to the "beginning" of the HDD, then make an image of it but and the entire disk, just the data. I've tried that with no luck since the image seem to get as big as the HDD, hence why I always needed to increase the HDD all the time.
I am facing an issue with 100% CPU usage under my system when running VirtualBox. Here are some further details:
My System Information:
CPU 1 name: Intel(R) Pentium(R) Dual CPU T2310 @ 1.46GHz CPU 1 level 1 cache size: 32K Data cache. 32K Instruction cache. CPU 1 level 2 cache size: 1024K Unified cache. CPU 1 Mips: 2926.20
[Code].....
Well, each time I run Windows XP from my VirtualBox, I see the CPU usage at almost 100%. I experience a slow system even if no programs were running on my hosted Windows XP version.
I was wondering if there is a way for me to play with the settings so I can slightly enhance the performance. My PC is relatively fast under my Linux operating system. I need to know if there are some tips that I may follow when configuring the settings of my VirtualBox so i can achieve better results.
I tried to install Portable VirtualBox using wine and even though I installed it on my /host/ folder (with 19 gb free) it downloaded some massive file on my Wubi installation (with 60 mb free) and now I am down to 3 mb left on Wubi and I can't find the massive file that it downloaded. Tried using the disk usage analyzer but nothing came up. Windows is unbootable so I can't use it.
Before this, Ubuntu would constantly decrease the amount of disk space I had free for no reason as well. It would jump from 120 mb one day to 50 mb.I moved my documents to my Windows folders but the disk space only stayed at 100 for another day or so before it went down again. apt-get auto/clean, localepurge, and deborphan are completely useless and there's something else going on behind the scenes here that I don't know about.Using Ubuntu Jaunty.
I am runnin Ubuntu 9.10- the Karmic Koala on acer aspire laptop. since everythin in this netbook is crap. so I hardly can see movies that so much going on in them( when so much happens, the screen freezer for a while therefore i miss the most interesting bits) I used kinda every players. the only one that works for me is mplayer since it does not require high spec it works good but it has its own costs. if I use mplayer then i have the porblem of the sound (eg i can hear stuff before it happening) I am now just wondering if there is a way to decrease the quality. I really dont care if i have great quality or not as long as i can c whats happening ( at least for this netbook anyway)
I was wondering why the chached RAM doesn't decrease at the same rate or near that when scanning is done & the scanning software is closed as it increases during scanning ? When the cached ram reaches a certain point while scanning, the software crashes & I loose my scans
in the last instalation of slackware(13 and 13.1) when I do login the sound is down, the vol speaker is zero, and I have increase this by alsamixer, kmixer etc.I try the alsaconf, alsactl estore but it back zero(no sound). How a do for it stay in predefined volume
How can I decrease the amount of video memory in a debian squeeze laptop? The amount of video memory is 1GB and I want to reduce it to 512MB or 256MB. How can I do this
Desperate to reduce RAM usage of my tiny VPS running Ubuntu 9.04 and Apache2.2.11, here I saw that: On Linux, each child process will use 8MB of memory by default. This is probably unnecessary. You can decrease the overall memory used by Apache by setting ThreadStackSize used by Apache by setting ThreadStackSize to 1MB in.
So I tried to give the suggestion a try. But when I append: ThreadStackSize 1000000 in my /etc/apache2/httpd.conf <IfModule mpm_prefork_module> directive, and restarted apache, it failed with this message: Invalid command 'ThreadStackSize', perhaps misspelled or defined by a module not included in the server configuration
So I figured out that the relevant modules are neither enabled nor available on apache2. Now I am wondering whether there is a way to decrease the ThreadStackSize without the need to compile apache from source? If not, what should I do?
I'm having a huge performance decrease when I'm on Battery Power. Plugged in this thing runs AMAZING, HDMI with HD video, I can run compiz 3d, full desktop advanced effects, HD video from ....., you name it. Just when I pull the cable out it slows down. I tried disabling ATI powerplay but that didnt help.
Is there a way I can toggle the performance, so that I can get "plugged in level performance" even when i'm on battery power? I'm not too bothered about how long the battery lasts. I'm usually always near an outlet.
Currently, I have on internal HDD 160GB in size. 20GB are for windows XP partition and the rest is assigned for ubuntu partition(s?). i want to make it now more equal in size, but how can i do that? I'm using ubuntu 11.04...
1- Does Linux operating system decrease the original size of the HDD? because first I was only using a Windows 7 Ultimate on my Laptop Lenovo G550 4446 the D:/ partition size was 140 GB Free of 190 GB.. After I installed the Linux ubuntu along with the other Windows 7 I found the D:/ partition size became 68 GB free of 122 GB... Why the hell the size decreased?? Did the HDD destroy?
2- How can I hack Wireless Network of type WPA2/WPA or WEP using the linux? I have heard that I can do that using Shell Konsole, but I can't see Shell Konsole in my Linux ubuntu 10.10... Is it required to be installed over the internet or something, or if it is already installed within the operating system, can you tell me where I can find it?
In /proc/scsi/scsi, we can see the scsi host no. (scsi identifier no.). for e.g. Host: scsi4 Channel: 00 Id: 01 Lun: 00 In above e.g., scsi identifier no. is 4. Whenever we modprobe a particular module associated with scsi devices, we can see new entry in/proc/scsi/scsi with a greater identifier no. When we do rmmod on that module, the entry from /proc/scsi/scsi wipes off but still the counter of scsi identifier no. doesn't decreases. is is there any way to reset or decrement this counter so that next time when I do modprobe on scsi related module, it will assign no.s starting with 0 ? I found that during registering a scsi device, scsi_register() method gets value from "next_host" (which is a static int initialized to 0) and then increments next_host counter. Also, during scsi_unregister(), it decrements next_host counter. rmmod internally calls scsi_unregister(). So, if it is true then why the scsi host id. doesn't decrement during rmmod?
Lately I have noted a decrease on the performance of my Ubuntu Karmic Koala 64 bits installation. It takes longer times to open applications and documents and sometimes the windows fade to grey and I have to wait. Can anyone give me some hint on where to start looking for a solution?
We have recently built some RAC (OS:RHEL55) servers and after the Oracle guys have installed their application, somehow the directory / is using the maximum space. I contacted the Oracle team & they say that their RAC installation doesn't create any files in the / directory. This is the o/p of '/' directory file system:
Filesystem Size Used Avail Use% Mounted on /dev/mapper/datavg-vol2 498M 382M 62M 88% /
Also, when I checked the file sizes, I found that the following files were taking more space:
I don't know what these files are doing there, when I did a cat and cheked, I found the files containing this data:
nf_tre--
stem_dbusd_var_run_t...and some stuff like this Unable to decide whether or not to remove these files. Also, is there any way to find out what files are taking more space and whether they can be deleted or not? in order to free up some space in the / direcoty. As there are 10 RACs that we've build, I got to do something to fix this for all of the 10 servers.
I am attempting to setup and old BBSinside of DosBOXI've built one of the DosBOX Megabuilds, with the NE2000 patch.It uses libpcap in order to piggy back on top of the system's NIC. All of the dosbox side appears to be working.My system comes up, gets the MAC address i told it to use, i can load a packet driver in dosbox, all of that seems well and good. The issue, i think, is on the linux side. It's built on a Fedora 14 box. I'm getting the feeling that networking isnt getting out of the dosbox instance. Does it seem possible that fedora needs to have some config in place to link networking over to dosbox?
I just want to use Internet Connection Sharing (ICS) to connect to the internet. I have done a massive amount of troubleshooting, but some of it seems to contradict itself, and the only two things that I know for sure are that it used to work, and that my Ethernet cable is not the problem. When I use Terminal utilities like ifup and dhclient it seems that it can not determine IP information, but when I try to put it in manually, the "Apply" button grays out right after I finish typing it in. When I try to connect normally, in KDE or GNOME, the icon acts like it's connecting, then instead of having the connected icon, I receive a notification that "the network has been disconnected", and it goes back to the disconnected icon.
Oh, and by the way, I know that I could probably find a workaround, but I have limited resources, and this used to work. The Linux is a Dell desktop with Fedora 12 and the Windows is a Windows 7 HP laptop.EDIT: I hope that I didn't mess something up, but I accidentally used system-network-config to try putting in the IP address there, and ended up changing it back to the original settings, but the computer is now calling it Auto Ethernet in the taskbar icon, although sudo iwconfig in the terminal still calls it eth0.
I am having a heck of a time trying to find directions on networking my two computers together in order to share files. I have two machines running Ubuntu 10.10 Desktop & Netbook remix.
They are both connected to my wireless router to connect to the internet.
i know exactly what i need to do, im just not familiar enough with command line to do it properly.i have 7 computers.the first 4 are connected to a router via wireless at one end of the house. of the last 3 only 1 will be able to access the router via wireless, so it needs to share it's one wireless connection via ethernet. this computer i'm going to call 'server'server will have two IP'swlan0 192.168.1.6 this connects to the router that has internet access.eth0 i intend to have the following settingsip:192.168.0.1sub: 255.255.0eth0 will connect to a second router, where the cat5 cable goes from the server, into the internet port of the router where i will define the router's static IP:IP: 192.168.0.100sub: 255.255.255.0gateway 192.168.0.1i have then set the router IP for LAN handling as 192.168.27.1 and all ethernet connections will have a 192.168.27.x IP.
so i need to know how to, without a gui application, use the terminal to assign server eth0 a proper IP address, and tell the server to take the connection it has and share it through eth0 to supply internet for the last 2 computers via ethernet.i had it set up in this way with a windows machine being the one that had the wifi access, but i'd rather have it setup for the ubuntu server to do this task. security is imperative for these 3 remaining machines, so just getting 2 more wifi adapters for a connection to the initial router isn't an option.the 2 that connect to server do so through SSH and though server IS connected via wireless it only makes outward connections through
I have installed fedora 12 recently. after installation i tried to connect to the internet using BSNL broadband connection. I filled in the details such as IP, Netmask, Gateway and even DNS servers. In the services also I ensured that the network manager services is on. However even though my computer cannot connect to the internet. I then tried the ping test of the modem from the address 192.168.1.1 and found that the ping test is successful. Then i tried the network administrator and there I noticed something unusual.
There are two options in the devices eth0 and eth1 thats ok but the unusual; thing is that the Activate (green button), Deactivate (red button) and even the delete buttons are in the background and I cannot select them. Isthis the problem for the network connectivity.
[Code]....
I then tried the ping test of the modem from the address 192.168.1.1 and found that the ping test is successful. Then i tried the network administrator and there I noticed something unusual. There are two options in the devices eth0 and eth1 thats ok but the unusual; thing is that the Activate (green button), Deactivate (red button) and even the delete buttons are in the background and I cannot select them. Isthis the problem for the network connectivity.
I just got connected to Charter Cable Internet service a few days ago and I'm having a weird problem with my home network. Prior to this my network worked fine. On my network I have a desktop running Ubuntu 9.10/64 and Virtualbox with WinXP installed, an HTPC with Ubuntu 9.10/32 installed and a laptop dual booted with Ubuntu 9.10/32 and WinXP. The desktop and HTPC are hard wired to a wireless router and the laptop is wireless. The cable modem is hard wired to the router. I have samba installed and UFW is disabled. The problem is: with the cable modem turned off or on standby, all machines connect to each other and can transfer files, etc just fine but when I activate the cable modem all of the machines can connect to the Internet but the machines running Ubuntu can't connect to each other on the home network. If I boot the laptop into Windows, it can connect to the Linux machines just fine but if I boot it into Linux, it won't connect to the Linux machines but it can connect to the Internet and as far as the desktop, Ubuntu won't connect to the network but Windows running in the Virtualbox with bridged networking can connect to all of the machines.
