Networking :: Forwarding All Internet Traffic Through Proxy
Jul 19, 2011
My PC is part of a LAN so while configuring eth0, we specify the Gateway to access all other resources in the network. The PC successfully access Internet through a proxy server configured in Mozilla(manual proxy config) but the update option or the Synaptic Pkg mngr are not able to access internet anyway. I have tried the option "Apply System Wide" in "Network Proxy" but no progress so far.
I also tried to forward all request coming for udp/tcp on port 80 to the proxyserver on a specific port, but with no success. Also I can't ping any website from terminal, reiterating the fact that I can access internet in firefox through the proxy on a specific port.
At the moment I have a proxy and all the users have to configure it in the browser to access internet. I want to make the users able to browse even without configuring the proxy in the browser. but eventually it should be received in the proxy rather than giving an error to the user. I heard with transparent proxy I can redirect all the traffic from a particular network, to a particular host( ie my existing proxy).
I tried this using firewall rules. But then the existing proxy doesn't understand the protocol of the requests. I heard that it should be in the kind of proxy protocol.
I have just recently switched my setup to have my server be in the middle of traffic and act as my new router while making my other routers just switches. However, after doing this I can no longer access my UPnP devices. They used to show up in my router but I am assuming either there is an issue with my iptables rules or that some how having my server run the dhcp and dns routing is messing with UPnP.
i want to redirect the packet to proxy server. can u help me.
Present network.
MY internal network ==> switch ==> proxyserver ==> router ==> internet. (for internet i use to connect proxy, in web browser==> lan settings ==> proxy server ip address )
What i want is
My internal network ==> getway or firewall ==> switch ==> proxy server ==> router==> internet. ( where this getway or firewall i can configure for forward http request to proxy server.)
so that i can separate my internal network from intranet but able to access the internet.
How do you set up a linux workstation to act as a gateway for all other PC's in the LAN giving them internal IP's using DHCP, but which also forces all access to the internet to go through a proxy running inside the same linux workstation at 127.0.0.1:9666?the proxy is provided by ultrasurf and run using wine and we do not want to set applications one by one to use a proxy - it must be an automatic effect.
I need to redirect all http/https/ftp traffic through the remote proxy, but when I changes connection settings in browser or in System->Preferences->Network Proxy it doesn't work well: instead of getting page content browser asks for saving some short (8 bytes) file with the same content for all requested pages. It happens in Chrome/Opera/Firefox. This proxy requires authorization and works on computer with Windos XP. It worked well when I was using Windows 7 and Proxifier, now I have Ubuntu 9.10 with all available updates.
I am new to iptables. We have two Squid proxy servers running in "non-transparent mode" (172.16.0.1 and 172.16.0.2). Currently users have to configure the proxy server they want to use by configuring them in their browsers. Recently I saw an example for redirecting web traffic to a single transparent proxy server.
Can anyone modify this rule to accommodate my current setup of two proxy servers running in non-transparent mode. i.e Redirect web traffic to the 172.16.0.1-172.16.0.2 ip range.
I am using Debian 5 and I have some networking experience, however I want to learn to do this the best way possible. I have a Debian box with two nics and I want to connect that to a switch and use my Debian box as a router basically, as well as having a firewall setup within that too.
Should I use iptables to set up nat or the route command or what? I just want to know the group of tools to use in order to set up my network. Network diagram: Internet <------> Debian Box <----> switch <----> hosts I found some guides but they are for linux 2.4 and i'm not sure if they are right.
I'm trying to setup a Centos 5.6 Squid Proxy Server with Content Filtering & Antivirus Scanning Incoming HTTP Traffic from the Internet
I then proceeded to setup an configure the Proxy Server, i was able to test and confirm that Squid and Dansguardian Content Filter is working, however i dont know if Clamav is scanning HTTP traffic before it hits the client/server. Is there a way i can check if the Antivirus scanning is working.. is there some log file or real world test i can i can do to confirm that Clamav is scanning incoming traffic or even blocking potential viruses ??
Anyone who has squid proxy server with Clamav configured and its working can share there settings/setup with me and how they tested it ??
here is what i need to do: [url]..... resolves to 209.5.5.5 which is my public IP on the external side of my router. Router is setup to forward (port forwarding) all port 80 based traffic to internal ip 192.168.1.10 which I want that server to lookup the request, and for web1 forward to 192.168.1.101, for web2 to .102 etc....how can i acheive this? What do i need to use?
We have something on our network that is reaking havoc with our content filter. I am trying to track it down, but so far I have been unsuccessful. We have approximately 500 devices in 100+ different locations spread across 9 states. Looking at each computer is not really feasible.
I need a machine that can sit in between our network and our internet connection and graphically monitor in real time and logs how much traffic each device is sending and receiving. It would need to sit inline so it has to have two nics and be able to pass traffic. The machine also needs to be transparent. Reconfiguration of our routers or workstations is not an option.
I have used ethereal and wireshark before. Ethereal may be a viable option, but wireshark seems to provide lots of information, but no practical way to make use of it. how to set up the box to be a transparent device on the network that will allow internet bound traffic to flow (freely)?
I am sharing my DSL internet connection using a modem+wireless router (single device) to 5 systems. I want all my internet traffic to go through one of the linux boxes in my network.
The problem here is that wireless devices connect directly to the modem+wireless router.
Is such routing of traffic possible??
PS: I am not sure if i could convey my situation clearly...
My ISP has given me 3 IP addresses to use for the internet (76.148.200.3, 76.148.200.4 and 76.148.200.5).
If I do a "wget whatismyip.com" or netcat into another server, I am appearing as 76.148.200.3.How do I change my route (command line) in linux to route internet traffic through 76.148.200.5?
Code: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo code....
I have eth0 and tun0. tun0 is a VPN tunnel going over eth0. Everything on the other end is setup and working fine, when I type Code: traceroute 4.2.2.1 I see my the ping is going over 192.168.2.99 (eth0). When I then type Code: route add -net 4.2.2.1 netmask 255.255.255.255 dev tun0 traceroute 4.2.2.1 I see ping is going over 10.8.0.1 (tun0) instead of eth0, so that is working
What does not work however is when I do Code: route add -net 0.0.0.0 netmask 0.0.0.0 dev tun0 traceroute 4.2.2.1 I get no ping! I believe the problem is because all traffic is routing over tun0, which means even the VPN tun0 needs to go through eth0, it can no longer do this. Is there a way around this where I can route everything except for 114.77.31.26 (which is my VPN gateway for tun0)?
I have a 2 machine LAN with both machines having an ethernet card and a wireless card. There is a Netgear router, both eth and WiFi, allowing both machines to access the internet.
On my Linux machine I am looking for some software that allows me to keep track of my broadband usage on that machine, excluding traffic between the two machines.
There are numerous such programmes for this in XP, which use Winpcap and a GUI frontend. The "other" machine on my LAN is XP and uses just such a program.
I have a desktop, a laptop, & a wireless router. The router, unfortunately, doesn't support dd-wrt, tomato, etc firmware, but I would still like to prioritize voip/web browsing over bulk Internet traffic. I hope I can offload the router's missing QoS to my desktop.
Is it possible to have the laptop's connection go from the wall to the router to the desktop, where the desktop could perform the QoS of tomato, then continue on to the laptop? I'm a bit of a noob to networking (subnets?) but do well enough following good instructions.
As for the program that would do the QoS... Don't some Linux machines basically work as super-powered routers for businesses? So there must be some package but couldn't find one. The closest I got was wondershaper but it only shapes traffic for the computer on which it's installed; it might form part of the solution but falls short on its own. other devices should be able to access the Internet normally if the desktop is turned off, & work with other devices like a (jailbroken) iPod Touch.
I have the standard wired LAN NIC and a wireless NIC installed. What my problem is, the wireless NIC will not take any internet traffic. The LAN connection gets it's internet from my LAPTOP with a Clear 4G module. I have a very strong wireless connection, but when I remove the LAPTOP from the network, I get nothing on my Ubuntu computer here, even though I have a solid connection. What is needed in the config to let the wireless run in the "back up" internet connection mode?
I have some questions about openVPN. I am wanting to hide my downloading through transmission and I'd like to know if I can use openVPN for this? Also do I need access to a server? I don't understand how it all works.
My internet gateway is 192.168.1.1 with a 255.255.255.0 subnet mask. I have a router connected to it running ddwrt with an ip 192.168.2.1/24 creating a second subnet behind it. I have a tenant moving in that will be wirelessly connecting to the ddwrt router, so to the 192.168.2.0/24 subnet. What I am looking for is a rule that will pass internet traffic to and from this client, but restrict him access from the 192.168.1.0/24 subnet otherwise. The ddwrt router is connected to the 192.168.1.1 gateway through its wan port, btw. For example, the client would get an ip address of 192.168.2.100 wirelessly from the ddwrt router. I want him to be able to surf the internet through the 192.168.1.1 gateway, but not to have any other access to the 192.168.1.0/24 subnet (ideally not have access to ANYTHING besides the internet).
Im running a web server on port80, but i want traffic coming from ip 212.333.111.222 on port 80 to be fowarded to port 9020 on the same server that my web server is rinning at that is my sshd port
Ubuntu system monitor applet doesn't show internet traffic although my wireless is working just fine. I use a conky to monitor bandwidth through vnstat and had no problem till I upgraded to maverick.
**ifconfig wlan0 Link encap:Ethernet HWaddr 00:24:d2:c4:3e:da inet adr:192.168.0.100 Bcast:192.168.0.255 Masque:255.255.255.0 adr inet6: fe80::224:d2ff:fec4:3eda/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
My Ubuntu Box has 3 interfaces. eth0 (Internal 192.168.1.0/24)eth1 (External ISP DHCP)eth2 (External ISP Static IP)I need the outgoing traffic to internet for 1 of the internal pc (192.168.1.10) to only go only go through eth2
Setting up an Internet proxy In the past I had set a computer to act as an Internet proxy. This would be multihomed, and running dansguardian, tinyproxy and firehol. Then webmin would be used as interface. By time I realised that this system is far from effective. Is there some other way to setup a proxy to be placed between users and the Internet? I would like (the admin) to be able to see in which sites users go and have a lot of control on access..
I need create ssh forwarding to other linux box that works as a proxy.I have two linux boxes(centos 5.5), one in the office(server1) behind firewall, other at colocation(server2)server1 has squid proxy instaled on port 3128.i cant use server1 as a direct proxy from home because its behind firewall.iwas able to create ssh tunnel from server1 to server2 and when i log in to server2 ican ssh root@localhost -p 12312 to server1
what i need is configure server2 so it forwards port server2:3128 to server1:3128....and i could add server2 ip addres and port to firefox proxy's and access ofice network.
I'm new to linux, but enjoy using it very much, especially without a GUI, console is fun! I need to set up port forwarding. We have 3 servers, 1x running Ubuntu server 8.04 (used as transparent proxy), 1x server 2003, 1x windows xp.
The linux box has the following ips: eth0 (internal) 192.168.1.5 eth1 (external) 192.168.0.7
Windows server 2003: 192.168.1.6
Windows XP: 192.168.1.9
Router: 192.168.0.1
The router automatically forwards specific ports to 196.168.0.7 (Linux eth0). From there I want to forward port 8585 to 192.168.1.6 and 3000 to 192.168.1.9. Is there a way that I can do this using iptables?
The commands that I think I'm gonna use look like this: iptables -A FORWARD -s 192.168.0.0/24 -p tcp --dport 8585 -d 192.168.1.6 -j ACCEPT iptables -A FORWARD -s 192.168.0.0/24 -p tcp --dport 3000 -d 192.168.1.9 -j ACCEPT
Would this be a correct way of doing it? My biggest problem is that I can't test it without going live, and if I go live and something doesn't work, the entire building will be left without internet, people will hate me. Also, The proxy captures all data on port 80 and forwards it to 3128 so that the proxy can monitor the usage, and a few systems runs fine with it, others however can ping websites, and internet explorer says "website found, waiting for reply" but the webpages cannot be displayed.
I would like to redirect traffic coming from a machine A through a SOCKS proxy (setted on machine B)Machine B run "ssh -D 4242". So that create a SOCKS proxy on machine B.Machine A would like to connect on the internet, but the only way is to use machine B SOCKS proxy. The problem is machine A don't know how to use SOCKS Proxy. (Actually, i can just set ip, netmask and gateway on machine A).So, I would like to set up something on machine B that will redirect all traffic coming from machine A throught the SOCKS proxy.
