I'm using Fedora Core5.0 I have using Iptables for forward port 80 to port 3128(Squid) in the same of server.I need to forward using Iptables to use the other proxy server because this server i am use for vpn and mail tranfer.What a Commnand for i use?ase 1. Server 1 >Ip 192.168.0.4 SQUID WITH PORT(3128)2. Server 2 IP 192.168.0.254 PF SENSE (3128) I will use server 2 for using internet connect only.
View 1 RepliesSo here is my issue in a nutshell. I need to take FTP requests that hit Server_A and forward them to Server_B. Server_B is not natted...Server_B is another public server in a completely different location in the world. One thing to note is that I only have one NIC hence why you will see both in and out being eth0. This is what I have in my iptables on SERVER_A:iptables -A FORWARD -p tcp -i eth0 --sport 21 -o eth0 -d SERVER_B --dport 21 -m state --state NEW -j ACCEPTiptables -A FORWARD -p tcp -i eth0 --sport 20 -o eth0 -d SERVER_B --dport 20 -m state --state NEW -j ACCEPTI've also tried both of the above without the --sport option. When I FTP to SERVER_A (where the above iptables rule are) it connects to SERVER_A instead of forwarding them to SERVER_B.
View 1 Replies View RelatedI need to forward a port to use dtella. I'm using Fedora 10, using iptables for my firewall.
I'm currently trying to forward it from terminal with this command:
Code:
sudo iptables -t nat -A PREROUTING -p udp -i eth0 -d [ip address] --dport 11823 -j DNAT --to 192.168.0.2:80
this is what I get from iptables -L
Chain INPUT (policy ACCEPT)
target prot opt source destination
ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED
[Code].....
I'd like to use ssh as a proxy/socks server and redirect all connections through this proxy.
It would look like : ssh -D 123 -N host
iptables ...
I've never used iptables before and I did not manage to find any useful for this particular case solutions on the internet.
So, what's the good way to do that ?
I am new to iptables. We have two Squid proxy servers running in "non-transparent mode" (172.16.0.1 and 172.16.0.2). Currently users have to configure the proxy server they want to use by configuring them in their browsers. Recently I saw an example for redirecting web traffic to a single transparent proxy server.
-A PREROUTING -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128
-A PREROUTING -p tcp -m tcp --dport 443 -j REDIRECT --to-ports 3128
Can anyone modify this rule to accommodate my current setup of two proxy servers running in non-transparent mode. i.e Redirect web traffic to the 172.16.0.1-172.16.0.2 ip range.
I am trying to set up my squid3 proxy as a transparent proxy - right now, I have to manually configure browsers to access via proxy. I understand that I have to put some rules into Iptables and also some further directives in the squid.conf.
I have a couple of specific questions. The proxy server is running on a Ubuntu 10.04 workstation and this machine also acts as a dhcp server for the network. I have just one subnet , namely 192.168.0.1-254 There is only 1 network card. Is it much easier to put in a second network card or is it just as easy to configure the existing lan card as a dual IP?
Is it necessary to configure these 2 IP's ( whether they are via 2 lan cards or dual IP on single card ) to be on different subnets. i.e ETH0 192.168.0.1 and ETH1 192.168.1.1 or is ok to have something like ETH0 192.168.0.1 and ETH1 192.168.0.254 ( where ETH0 is the one facing the LAN and ETH1 points to the modem router / switch i.e The Internet ) Where specifically do I save the Iptables rule configuration file and what must I call it ?
i have the following ip assignments
fedora (iptables)
eth0 -private :192.168.1.1
eth1 -public : 186.117.50.6
squid proxy
192.168.1.10:3128
my clients range
192.168.2.0/24
how can i make my clients to browse internet only from proxy server my network is NAT 'ed. Please specify a iptable rule to allow internet access for my clients to browse ONLY if they come through proxy server.
my company is a small company!and it only have one public ip,but my company have a lot of websites to access!now i use Reverse Proxy Server -- apahce to solve temporary!it is not convenience for me !So i think out whether iptables can not be used to forward according to the domain!!it is the test as follows:
public ip :10.0.0.1
privite ip1 :192.168.1.1
matching website domain:www1.test.com
privite ip2:192.168.1.2
matching website domain:www2.test.com
and if someone access [URL] the iptables will know they want to access 192.168.1.1 and it will forward to the server 192.168.1.1!!
How can I forward ssl protocol to another proxy with iptables or squid or something?I want to forward ssl protocol to xxx.xxx.xxx.xxx:443 when get ssl request from clients
=======n Windows I am OK with Mozilla browser:I can choice ssl protocol from Tools => options => Advanced => Network => setting => manual proxy configuration => ssl proxy:xxx.xxx.xxx.xxx:443this is OK for me How can I setup in linux for clients?(no need for manual choice ssl proxy in client browser)
I have three machines on three networks192.x.x.x10.x.x.x172.x.x.xThe routers are set to forward communication between 192. network and 10. network, and between the 10. network and the 172. network.However, there's not routing between 192. and 172.I want to fix that by using a machine on the 10. network to forward communication between the other two networks.The machine has one etherent connection eth0 whose address is 10.1.1.11I set up an aliased ip address eth0:0 to be 10.1.1.12 using Quote:ifconfig eth0:0 10.1.1.12Then I tried to set forwarding rules the 10. machine such that 10.1.1.12 address will provide access to the machine 172.1.1.55 as followsQuote:# iptables -t nat -A PREROUTING -d 10.1.1.12 -j DNAT --to-destination 172.1.1.55The default policies for all chains is ACCEPT.I then try to access 10.1.1.12 from 192.1.1.20 expecting it to actually access 172.1.1.55 ; it does not work
View 3 Replies View RelatedLets say i have two machines on public ips. If i get incoming traffic on machine #1 on port 55242 i would just like to forward it to machine #2 on port 35000.I would just like to use machine #1 same way as a dns server works. It just redirects the traffic and tells the client where to go.
View 6 Replies View RelatedWe use a reverse proxy to forward a lot of websites via 1 central place.so hould forward to an internal server.I already managed to forward a lot of website correctly, except for this one:hen I type:ttp://blablahblah/smt/webtier-7-11 it doesn't work correctly, but How can I make the first url to work ?
ProxyPass /smt http://192.168.10.38:8080
ProxyPassReverse /smt http://192.168.10.38:8080
ProxyPassMatch ^/((smt|webtier-7.11)(/.*)?)?$ http://192.168.10.38:8080/$1
[code]....
iptables and multiple public-facing IP addresses. With the current setup I have a public-facing firewall with iptables which will then forward traffic to a LAN IP. I will hopefully be allotted 1 private IP per public IP, which I hope will make this much more simple. For example, I have server A with the LAN IP of 10.0.0.1 which I would like to have traffic forwarded from 5.0.0.1, the public IP. I also have server B with LAN IP of 10.0.0.2 which I would like to have forwarded from 5.0.0.2, the second public IP. From what I have read and understood, this should be a simple task, however I would just like to double check to make sure that it is in fact possible, and if so, how would it be recommended that I go about doing so. Essentially, I need to forward each public IP to a corresponding LAN IP with all ports.
View 3 Replies View RelatedThe goal is to make connection calls (ssh, ping, ...) possible from one LAN (LAN-1) to a number of (at the moment two) separate smaller LANs.These smaller LANs (LAN-2a, LAN-2b, ...) have exact same specifications (same IP range, same number of nodes, ...)!The idea is to use a Fedora box (release 14 with 2.6.35.6-45.fc14.i686) and implement an appropriate iptables routing/forwarding.The Fedora box has three network interfaces:
- eth0 (aaa.bbb.ccc.m) on LAN-1 (aaa.bbb.ccc.0/24)
- eth1 (ddd.eee.fff.n) on LAN-2a (ddd.eee.fff.0/27)
- eth2 (ddd.eee.fff.p) on LAN-2b (ddd.eee.fff.0/27)
[code]....
How to forward local HTTP requests to remote Proxy with IPTables ?
View 1 Replies View RelatedI just upgraded my fedora 13 to fedora 14. I changed the cpu and the motherboard so i had to install from scratch...but I saved my iptables.
The problem is that
I do all the suff
service iptables save
And apparently it works...
But everytime I reboot I have to re run the script to forward Internet...Everything else works just fine...I mean I can ssh, vnc, etc but wont forward intel :S dont know why?
What commands do you use to set the INPUT, OUTPUT, and FORWARD chains in iptables to ACCEPT?
View 5 Replies View RelatedI have big problem with correct settings of iptables as a router. My network topology (UTM Hardware router) 192.168.1.1--->eth0 192.168.1.2(centos with apache ftp and transparent squid 8080)--->eth1 192.168.0.1(LAN with dhcp)
eth0=WAN 192.168.1.2
eth1=LAN 192.168.0.1
I have problem with hanging connections through squid which are very slow or connection failed. Sometimes i received DNS timeout error from squid stable 2.6 21
[Code]...
I need to set up an ip table and a transparent squid proxy as followed: I have 3 machine: Machine 1 works as a squid proxy. It has 2 interface eth1 and eth2.
eth1: 192.168.99.2 (Connect to eth1 of machine 2)
eth2: 192.168.98.2 (Connect to eth1 of machine 3)
machine 2 works as a webserver
eth1: 192.168.99.4
machine 3 works as a web client.
eth1: 192.168.98.4
my responsibility is to send all tcp traffic from machine 3 at port 80 to my squid proxy. In order to fulfill the tasks, I have edited the squid.conf as followed: Code: http_access allow localnet http_access allow localhost and in machine 1, I tried 2 ip tables command: Code: iptables -t nat -A PREROUTING -i eth2 -p tcp --dport 80 -j DNAT --to 192.168.99.2:80 iptables -t nat -A PREROUTING -i eth1 -p tcp --dport 80 -j REDIRECT --to-port 80 I don't know if it is right or wrong.
I'm trying to access my oracle database (port 1521) from the outside.What I have:Outside -----> Proxy ----> DatabaseWhat I try is to configure a reverse proxy or iptables for accepting connections on port 1521 and transfer them to database. Only one computer of the outside will have access to the database.I suppose than this can be done with iptables or another way.In the real environment proxy will have two nicut for test purposes my computer will have only one (for test purposes, the tree computer will be in the same net)
View 11 Replies View RelatedIf I forward port 80 to port 3128 for squid with an iptable rule, does port 3128 have to be open on the firewall or is this all routed behind the firewall?
View 4 Replies View RelatedI setup squid with transparent proxy and its working, however, when I reboot the server, the proxy server doesnt work unless I run the following.
Code: # squid server IP
SQUID_SERVER="192.168.1.1"
# Interface connected to Internet
INTERNET="eth0"
# Interface connected to LAN
LAN_IN="eth1"
# Squid port
SQUID_PORT="3128"
[Code]...
I'm trying to use iptables in order to forward all the incoming packets for port 5555 to port 5556 on the same server (192.168.2.101).
I wrote the following commands:
iptables -A PREROUTING -t nat -i any -p tcp --dport 5555 -j DNAT --to 192.168.2.101:5556
iptables -A FORWARD -p tcp -m state --state NEW -d 192.168.2.101 --dport 5556 -j ACCEPT
I'm using a Debian servers, as router/firwall.. I've two ethernet interfaces into the server, one for wan and one for lan. The i use SNAT so my LAN clients can access the internet throgh the debian router. That is working... Now i want to be able to access servers on the LAN site from the WAN site, and i wanna use port address translation (PAT). I have a FTP server running on a lan server, so i'm trying to portward port 21.
iptables -t nat -A PREROUTING -p tcp -i eth1 -d (WANIP) --dport 21 -j DNAT --to 192.168.1.2:21
When people try to access my FTP from the WAN site, they are redirected to the local FTP server, and they are promted for crendentials, but when the credentials are typed, and the local ftp server should answer the wan request, the connections dies.
The wan clients are being promted for credentials, so they are redirected to the local lan server, but after that the connections dies, so i think there is some kind of nat problem, when the local lan server is trying to respond to the wan request..
Here i my iptables script:
#flush table
iptables -F
#input regler
[code]....
Currently my DHCP Server is working now what i want to have is auto detection of squid proxy in any browser but I still got an error in my dhcp server when I restart it.
My Config:
# DHCP configuration generated by Firestarter
ddns-update-style interim;
ignore client-updates;
[code]....
I'm a network administrator and I have to cut the internet access to some network users. I would like to do that by installing a proxy server on a F10/F11/F12.
View 5 Replies View RelatedI am trying to do a NAT forward in iptables but get the following error:Quote:[root@server88-xxx-xxx-198 openvpn]# iptables -t nat -I POSTROUTING -i tun0 -o eiptables v1.3.5: Can't use -i with POSTROUTINGAny ideas on what to do?I have an OpenVON server running and I need the client to use the ports on the OpenVPN server
View 8 Replies View RelatedI`m running a rather simple iptables script, but no matter what port i try to forward it wont open. Here are the basics:
Code:
ipt="/usr/sbin/iptables"
$ipt -F
[code]...
Am using Fedora 15, in which i was able to configure the proxy server and authentication. i confirmed this by configuring web broswer and it works. Now the problem is that i want to deploy it out to other computer system(client) i dont want to use the transparent proxy because the Proxy Authentication will not work.
I even tried to configure a DHCP server if it will work but i cant still configure for other computer system to work.
My router has two bridges, br0 and br1. I'm sharing wifi access, and the guest subnet will be 192.168.2.x.The home subnet will be 192.168.1.x. I want all traffic destined for port 80 from the guest net to forward to a proxy port on a box on the home network. That's the only traffic I want to cross the bridges. How do I set this up with iptables on the router?
View 1 Replies View Related